INTEL D98324

Intel® Desktop Board
D945GCPE
Technical Product Specification
July 2007
Order Number: D98324-001US
The Intel® Desktop Board D945GCPE may contain design defects or errors known as errata that may cause the product to deviate from published specifications. Current
characterized errata are documented in the Intel Desktop Board D945GCPE Specification Update.
Revision History
Revision
Revision History
Date
-001
This is the first release of the Intel® Desktop Board D945GCPE Technical
July 2007
Product Specification
This product specification applies to only the standard Intel Desktop Board D945GCPE with BIOS
identifier PE94510M.86A.
Changes to this specification will be published in the Intel Desktop Board D945GCPE
Specification Update before being incorporated into a revision of this document.
INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL® PRODUCTS. NO LICENSE,
EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS
GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL’S TERMS AND CONDITIONS OF SALE FOR
SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR
IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR
WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT
OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. INTEL PRODUCTS ARE NOT
INTENDED FOR USE IN MEDICAL, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS.
Intel Corporation may have patents or pending patent applications, trademarks, copyrights, or other
intellectual property rights that relate to the presented subject matter. The furnishing of documents and
other materials and information does not provide any license, express or implied, by estoppel or otherwise,
to any such patents, trademarks, copyrights, or other intellectual property rights.
Intel may make changes to specifications and product descriptions at any time, without notice.
Designers must not rely on the absence or characteristics of any features or instructions marked “reserved”
or “undefined.” Intel reserves these for future definition and shall have no responsibility whatsoever for
conflicts or incompatibilities arising from future changes to them.
Intel® desktop boards may contain design defects or errors known as errata, which may cause the product
to deviate from published specifications. Current characterized errata are available on request.
Contact your local Intel sales office or your distributor to obtain the latest specifications before placing your
product order.
Copies of documents which have an ordering number and are referenced in this document, or other Intel
literature, may be obtained from:
Intel Corporation
P.O. Box 5937
Denver, CO 80217-9808
or call in North America 1-800-548-4725, Europe 44-0-1793-431-155, France 44-0-1793-421-777,
Germany 44-0-1793-421-333, other Countries 708-296-9333.
Intel, the Intel logo, Pentium, Intel Core 2 Duo, and Celeron are registered trademarks of Intel Corporation
or its subsidiaries in the United States and other countries.
* Other names and brands may be claimed as the property of others.
Copyright © 2007, Intel Corporation. All rights reserved.
Preface
This Technical Product Specification (TPS) specifies the board layout, components,
connectors, power and environmental requirements, and the BIOS for the Intel®
Desktop Board D945GCPE. It describes the standard product and available
manufacturing options.
Intended Audience
The TPS is intended to provide detailed, technical information about the Desktop Board
D945GCPE and its components to the vendors, system integrators, and other
engineers and technicians who need this level of information. It is specifically not
intended for general audiences.
What This Document Contains
Chapter
Description
1
A description of the hardware used on the Desktop Board D945GCPE
2
A map of the resources of the Desktop Board
3
The features supported by the BIOS Setup program
4
A description of the BIOS error messages, beep codes, and POST codes
5
Regulatory compliance and battery disposal information
Typographical Conventions
This section contains information about the conventions used in this specification. Not
all of these symbols and abbreviations appear in all specifications of this type.
Notes, Cautions, and Warnings
NOTE
Notes call attention to important information.
#
INTEGRATOR’S NOTES
Integrator’s notes are used to call attention to information that may be useful to
system integrators.
CAUTION
Cautions are included to help you avoid damaging hardware or losing data.
iii
Intel Desktop Board D945GCPE Technical Product Specification
WARNING
Warnings indicate conditions which, if not observed, can cause personal injury.
Other Common Notation
iv
#
Used after a signal name to identify an active-low signal (such as USBP0#).
(NxnX)
When used in the description of a component, N indicates component type, xn are the
relative coordinates of its location on the Desktop Board D945GCPE, and X is the instance of
the particular part at that general location. For example, J5J1 is a connector, located at 5J.
It is the first connector in the 5J area.
GB
Gigabyte (1,073,741,824 bytes)
GB/sec
Gigabytes per second
Gbits/sec
Gigabits per second
KB
Kilobyte (1024 bytes)
Kbit
Kilobit (1024 bits)
kbits/sec
1000 bits per second
MB
Megabyte (1,048,576 bytes)
MB/sec
Megabytes per second
Mbit
Megabit (1,048,576 bits)
Mbit/sec
Megabits per second
xxh
An address or data value ending with a lowercase h indicates a hexadecimal value.
x.x V
Volts. Voltages are DC unless otherwise specified.
*
This symbol is used to indicate third-party brands and names that are the property of their
respective owners.
Contents
1 Product Description
1.1 Overview........................................................................................ 10
1.1.1 Feature Summary ................................................................ 10
1.1.2 Board Layout ....................................................................... 12
1.1.3 Block Diagram ..................................................................... 14
1.2 Online Support................................................................................ 15
1.3 Processor ....................................................................................... 15
1.4 System Memory .............................................................................. 16
1.4.1 Memory Configurations ......................................................... 17
1.5 Intel® 945GC Chipset ...................................................................... 17
1.5.1 Intel 945GC Graphics Subsystem............................................ 17
1.5.2 USB ................................................................................... 19
1.5.3 IDE Support ........................................................................ 19
1.5.4 Real-Time Clock, CMOS SRAM, and Battery .............................. 21
1.6 Legacy I/O Controller ....................................................................... 21
1.6.1 Diskette Drive Controller ....................................................... 21
1.6.2 Keyboard and Mouse Interface ............................................... 21
1.7 Audio Subsystem............................................................................. 22
1.7.1 Audio Subsystem Software .................................................... 22
1.7.2 Audio Connectors ................................................................. 22
1.7.3 Four Channel Audio Subsystem .............................................. 22
1.8 LAN Subsystem ............................................................................... 23
1.8.1 LAN Subsystem Software....................................................... 23
1.8.2 Realtek RTL8101E-GR Fast Ethernet Controller ......................... 24
1.9 Hardware Management Subsystem .................................................... 25
1.9.1 Hardware Monitoring and Fan Control...................................... 25
1.9.2 Chassis Intrusion and Detection.............................................. 25
1.9.3 Fan Monitoring ..................................................................... 25
1.9.4 Thermal Monitoring .............................................................. 26
1.10 Power Management ......................................................................... 27
1.10.1 ACPI .................................................................................. 27
1.10.2 Hardware Support ................................................................ 29
2 Technical Reference
2.1 Memory Resources .......................................................................... 34
2.1.1 Addressable Memory............................................................. 34
2.2 Connectors and Headers................................................................... 36
2.2.1 Back Panel Connectors .......................................................... 37
2.2.2 Component-side Connectors and Headers ................................ 38
2.3 Jumper Block .................................................................................. 46
2.4 Mechanical Considerations ................................................................ 48
2.4.1 Form Factor......................................................................... 48
2.5 Electrical Considerations ................................................................... 49
v
Intel Desktop Board D945GCPE Technical Product Specification
2.5.1 Power Supply Considerations .................................................
2.5.2 Fan Header Current Capability................................................
2.5.3 Add-in Board Considerations ..................................................
2.6 Thermal Considerations ....................................................................
2.7 Reliability .......................................................................................
2.8 Environmental ................................................................................
49
50
50
50
52
53
3 Overview of BIOS Features
3.1 Introduction ...................................................................................
3.2 BIOS Flash Memory Organization .......................................................
3.3 Resource Configuration ....................................................................
3.3.1 PCI Autoconfiguration ...........................................................
3.3.2 PCI IDE Support...................................................................
3.4 System Management BIOS (SMBIOS).................................................
3.5 BIOS Updates .................................................................................
3.5.1 Language Support ................................................................
3.5.2 Custom Splash Screen ..........................................................
3.6 Legacy USB Support ........................................................................
3.7 Boot Options...................................................................................
3.7.1 CD-ROM Boot ......................................................................
3.7.2 Network Boot.......................................................................
3.7.3 Booting Without Attached Devices...........................................
3.7.4 Changing the Default Boot Device During POST ........................
3.8 Adjusting Boot Speed.......................................................................
3.8.1 Peripheral Selection and Configuration.....................................
3.8.2 BIOS Boot Optimizations .......................................................
3.9 BIOS Security Features ....................................................................
55
56
56
56
57
57
58
58
58
59
59
59
59
60
60
61
61
61
62
4 Error Messages and Beep Codes
4.1 BIOS Front-panel Power LED Codes.................................................... 63
4.2 BIOS Error Messages ....................................................................... 63
4.3 Port 80h POST Codes ....................................................................... 64
5 Regulatory Compliance and Battery Disposal Information
5.1 Regulatory Compliance.....................................................................
5.1.1 Safety Standards..................................................................
5.1.2 European Union Declaration of Conformity Statement ................
5.1.3 Product Ecology Statements...................................................
5.1.4 EMC Regulations ..................................................................
5.1.5 Product Certification Markings (Board Level).............................
5.2 Battery Disposal Information.............................................................
vi
69
69
70
71
75
76
77
Contents
Figures
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Board Components ..........................................................................
Block Diagram ................................................................................
Back Panel Audio Connector Options ..................................................
LAN Connector LED Locations ............................................................
Thermal Sensors and Fan Headers .....................................................
Location of the Standby Power Indicator LED .......................................
Detailed System Memory Address Map ...............................................
Back Panel Connectors .....................................................................
Component-side Connectors and Headers ...........................................
Connection Diagram for Front Panel Header .........................................
Connection Diagram for Front Panel USB Headers.................................
Location of the Jumper Block .............................................................
Board Dimensions ............................................................................
Localized High Temperature Zones .....................................................
12
14
23
24
26
32
35
37
38
43
45
46
48
51
Tables
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
Feature Summary............................................................................
Board Components Shown in Figure 1 ................................................
Supported Memory Configurations .....................................................
LAN Connector LED States ................................................................
Effects of Pressing the Power Switch ..................................................
Power States and Targeted System Power...........................................
Wake-up Devices and Events ............................................................
Component-side Connectors and Headers Shown in Figure 9 .................
Front Panel Audio Header .................................................................
Chassis Intrusion Header ..................................................................
Serial ATA Connectors ......................................................................
Serial Port Header ...........................................................................
Processor Fan Header ......................................................................
Chassis Fan Header .........................................................................
Main Power Connector......................................................................
Processor Core Power Connector........................................................
Auxiliary Front Panel Power/Sleep LED Header.....................................
Front Panel Header ..........................................................................
States for a One-Color Power LED ......................................................
States for a Two-Color Power LED......................................................
BIOS Setup Configuration Jumper Settings..........................................
Recommended Power Supply Current Values .......................................
Fan Header Current Capability...........................................................
Thermal Considerations for Components .............................................
Environmental Specifications.............................................................
BIOS Setup Program Menu Bar..........................................................
BIOS Setup Program Function Keys....................................................
Boot Device Menu Options ................................................................
10
13
16
24
27
28
29
39
40
40
40
40
41
41
41
42
42
43
44
44
47
49
50
52
53
56
56
60
vii
Intel Desktop Board D945GCPE Technical Product Specification
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
viii
Supervisor and User Password Functions.............................................
Front-panel Power LED Blink Codes ....................................................
BIOS Error Messages .......................................................................
Port 80h POST Code Ranges..............................................................
Port 80h POST Codes .......................................................................
Typical Port 80h POST Sequence........................................................
Safety Standards.............................................................................
Lead-Free Board Markings ................................................................
EMC Regulations .............................................................................
Product Certification Markings ...........................................................
62
63
63
64
65
68
69
74
75
76
1
Product Description
What This Chapter Contains
1.1 Overview........................................................................................ 10
1.2 Online Support................................................................................ 15
1.3 Processor ....................................................................................... 15
1.4 System Memory .............................................................................. 16
1.5 Intel® 945GC Chipset ...................................................................... 17
1.6 Legacy I/O Controller ....................................................................... 21
1.7 Audio Subsystem............................................................................. 22
1.8 LAN Subsystem ............................................................................... 23
1.9 Hardware Management Subsystem .................................................... 25
1.10 Power Management ......................................................................... 27
9
Intel Desktop Board D945GCPE Technical Product Specification
1.1
Overview
1.1.1
Feature Summary
Table 1 summarizes the major features of the board.
Table 1. Feature Summary
Form Factor
microATX (8.60 inches by 9.60 inches [218.44 millimeters by
243.84 millimeters])
Processor
Support for the following:
• Intel® Core™2 Duo processor in an LGA775 socket with a 1066 or 800 MHz
system bus
• Intel® Pentium® Dual-Core processor in an LGA775 socket with an 800 MHz
system bus
• Intel® Pentium® D processor in an LGA775 socket with an 800 or 533 MHz
system bus
• Intel® Pentium® 4 processor in an LGA775 socket with an 800 or 533 MHz
system bus
• Intel® Celeron® processor 400 series in an LGA775 socket with an 800 MHz
system bus
• Intel® Celeron D processor in an LGA775 socket with a 533 MHz system bus
Memory
• Two 240-pin DDR2 SDRAM Dual Inline Memory Module (DIMM) sockets
• Support for DDR2 667 or DDR2 533 MHz DIMMs
• Support for up to 2 GB of system memory
Chipset
Intel® 945GC Chipset, consisting of:
• Intel® 82945GC Graphics Memory Controller Hub (GMCH)
• Intel® 82801GB I/O Controller Hub (ICH7)
Video
Intel® Graphics Media Accelerator 950 (Intel® GMA950) onboard graphics
subsystem
Audio
Four channel (2 + 2) High Definition audio subsystem using the Realtek* ALC662
audio codec
Legacy I/O Control
ITE 8718F/GX legacy I/O controller for diskette drive, serial header, and PS/2*
ports
Peripheral
Interfaces
• Eight USB 2.0 ports
• Two Serial ATA interfaces
• One Parallel ATA IDE interface with UDMA 33, ATA-66/100 support
• One diskette drive interface
• PS/2 keyboard and mouse ports
LAN Support
10/100 Mbits/sec LAN subsystem using the Realtek RTL8101E-GR Ethernet
Controller
BIOS
• Intel® BIOS (resident in the SPI Flash device)
• Support for Advanced Configuration and Power Interface (ACPI), Plug and Play,
and SMBIOS
Expansion
Capabilities
• Two PCI* Conventional bus connectors
continued
10
Product Description
Table 1. Feature Summary (continued)
Instantly Available
PC Technology
• Support for PCI Local Bus Specification Revision 2.3
Hardware Monitor
Subsystem
• Hardware monitoring and fan control through the ITE 8718F/GX I/O controller
• Suspend to RAM support
• Wake on PCI, RS-232, front panel, PS/2 devices, and USB ports
• Voltage sense to detect out of range power supply voltages
• Thermal sense to detect out of range thermal values
• Two fan headers
• Two fan sense inputs used to monitor fan activity
• Fan speed control
For information about
Refer to
Available configurations for the board
Section 1.2, page 15
11
Intel Desktop Board D945GCPE Technical Product Specification
1.1.2
Board Layout
Figure 1 shows the location of the major components.
Figure 1. Board Components
Table 2 lists the components identified in Figure 1.
12
Product Description
Table 2. Board Components Shown in Figure 1
Item/callout
from Figure 1
Description
A
Front panel audio header
B
PCI Conventional bus add-in card connector #2
C
PCI Conventional bus add-in card connector #1
D
Rear chassis fan header
E
Back panel connectors
F
Processor core power connector (2 X 2)
G
Intel 82945GC GMCH
H
LGA775 processor socket
I
Processor fan header
J
DIMM socket
K
DIMM socket
L
Main Power connector (2 X 12)
M
Diskette drive connector
N
Parallel ATE IDE connector
O
Battery
P
Serial ATA connectors [2]
Q
Auxiliary front panel power LED header
R
Front panel header
S
BIOS Setup configuration jumper block
T
Chassis intrusion header
U
Intel 82801GB I/O Controller Hub (ICH7)
V
Front panel USB header
W
Front panel USB header
X
Serial port header
13
Intel Desktop Board D945GCPE Technical Product Specification
1.1.3
Block Diagram
Figure 2 is a block diagram of the major functional areas.
Figure 2. Block Diagram
14
Product Description
1.2
Online Support
To find information about…
Visit this World Wide Web site:
Intel® Desktop Board D945GCPE
http://www.intel.com/products/motherboard/D945GCPE/index.htm
Desktop Board Support
http://support.intel.com/support/motherboards/desktop
Available configurations for the
Desktop Board D945GCPE
http://www.intel.com/products/motherboard/D945GCPE/index.htm
Supported processors
http://www.intel.com/go/findcpu
Chipset information
http://www.intel.com/products/desktop/chipsets/index.htm
BIOS and driver updates
http://downloadcenter.intel.com
Tested Memory
http://support.intel.com/support/motherboards/desktop/sb/CS025414.htm
1.3
Processor
The board is designed to support the following processors:
•
•
•
•
•
•
Intel Core 2 Duo processor in an LGA775 socket with a 1066 or 800 MHz
system bus
Intel Pentium Dual-Core processor in an LGA775 socket with an 800 MHz system
bus
Intel Pentium D processor in an LGA775 socket with an 800 or 533 MHz
system bus
Intel Pentium 4 processor in an LGA775 socket with an 800 or 533 MHz system bus
Intel Celeron processor 400-series in an LGA775 socket with an 800 MHz system
bus
Intel Celeron D processor in an LGA775 socket with a 533 MHz system bus
See the Intel web site listed below for the most up-to-date list of supported
processors.
For information about…
Refer to:
Supported processors
http://www.intel.com/go/findcpu
CAUTION
Use only the processors listed on web site above. Use of unsupported processors can
damage the board, the processor, and the power supply.
#
INTEGRATOR’S NOTE
Use only ATX12V-compliant power supplies.
For information about
Refer to
Power supply connectors
Section 2.2.2.1, page 41
15
Intel Desktop Board D945GCPE Technical Product Specification
1.4
System Memory
The board has two DIMM sockets and supports the following memory features:
•
•
•
•
•
•
•
1.8 V (only) DDR2 SDRAM DIMMs with gold-plated contacts
Unbuffered, single-sided or double-sided DIMMs with the following restriction:
Double-sided DIMMS with x16 organization are not supported.
2 GB maximum total system memory. Refer to Section 2.1.1 on page 34 for
information on the total amount of addressable memory.
Minimum total system memory: 128 MB
Non-ECC DIMMs
Serial Presence Detect
DDR2 667 MHz or DDR2 533 MHz SDRAM DIMMs
NOTE
To be fully compliant with all applicable DDR SDRAM memory specifications, the board
should be populated with DIMMs that support the Serial Presence Detect (SPD) data
structure. This allows the BIOS to read the SPD data and program the chipset to
accurately configure memory settings for optimum performance. If non-SPD memory
is installed, the BIOS will attempt to correctly configure the memory settings, but
performance and reliability may be impacted or the DIMMs may not function under the
determined frequency.
Table 3 lists the supported DIMM configurations.
Table 3. Supported Memory Configurations
DIMM Capacity
Configuration
SDRAM Density
SDRAM Organization
Front-side/Back-side
Number of
SDRAM Devices
128 MB
SS
256 Mbit
16 M x 16/empty
4
256 MB
SS
256 Mbit
32 M x 8/empty
8
256 MB
SS
512 Mbit
32 M x 16/empty
4
512 MB
DS
256 Mbit
32 M x 8/32 M x 8
16
512 MB
SS
512 Mbit
64 M x 8/empty
8
512 MB
SS
1 Gbit
64 M x 16/empty
4
1024 MB
DS
512 Mbit
64 M x 8/64 M x 8
16
1024 MB
SS
1 Gbit
128 M x 8/empty
8
Note: In the second column, “DS” refers to double-sided memory modules (containing two rows of SDRAM)
and “SS” refers to single-sided memory modules (containing one row of SDRAM).
16
For information about…
Refer to:
Tested Memory
http://support.intel.com/support/motherboards/desktop/sb/CS025414.htm
Product Description
1.4.1
Memory Configurations
The Intel 82945GC GMCH supports two types of memory organization:
•
•
Dual channel (Interleaved) mode. This mode offers the highest throughput for
real world applications. Dual channel mode is enabled when the installed memory
capacities of both DIMM channels are equal. Technology and device width can vary
from one channel to the other but the installed memory capacity for each channel
must be equal. If different speed DIMMs are used between channels, the slowest
memory timing will be used.
Single channel (Asymmetric) mode. This mode is equivalent to single channel
bandwidth operation for real world applications. This mode is used when only a
single DIMM is installed or the memory capacities are unequal. Technology and
device width can vary from one channel to the other. If different speed DIMMs are
used between channels, the slowest memory timing will be used.
For information about…
Refer to:
Memory Configuration
Examples
http://www.intel.com/support/motherboards/desktop/sb/cs-011965.htm
1.5
Intel® 945GC Chipset
The Intel 945GC chipset consists of the following devices:
•
•
Intel 82945GC Graphics Memory Controller Hub (GMCH) with Direct Media
Interface (DMI) interconnect
Intel 82801GB I/O Controller Hub (ICH7) with DMI interconnect
The GMCH component provides interfaces to the CPU, memory, and the DMI
interconnect. The component also provides integrated graphics capabilities supporting
3D, 2D and display capabilities. The ICH7 is a centralized controller for the board’s
I/O paths.
For information about
Refer to
The Intel 945GC chipset
http://www.intel.com/products/desktop/chipsets/index.htm
Resources used by the chipset
Chapter 2
1.5.1
Intel 945GC Graphics Subsystem
1.5.1.1
Intel® GMA950 Graphics Controller
The Intel GMA950 graphics controller features the following:
•
•
•
400 MHz core frequency
High performance 3-D setup and render engine
High quality texture engine
⎯ DX9* Compliant Hardware Pixel Shader 2.0
⎯ Alpha and luminance maps
17
Intel Desktop Board D945GCPE Technical Product Specification
⎯ Texture color-keying/chroma-keying
⎯ Cubic environment reflection mapping
•
⎯ Enhanced texture blending functions
3D Graphics Rendering enhancements
⎯ 1.3 Dual Texture GigaPixel/Sec Fill Rate
⎯ 16 and 32 bit color
⎯ Maximum 3D supported resolution of 1600 x 1200 x 32 at 85 Hz
⎯ Vertex cache
⎯ Anti-aliased lines
•
⎯ OpenGL* version 1.4 support with vertex buffer and EXT_Shadow extensions
2D Graphics enhancements
⎯ 8, 16,and 32 bit color
⎯ Optimized 256-bit BLT engine
⎯ Color space conversion
•
⎯ Anti-aliased lines
Video
⎯ Hardware motion compensation for MPEG2
•
⎯ Software DVD at 30 fps full screen
Display
⎯ Integrated 24-bit 400 MHz RAMDAC
⎯ Up to 2048 x 1536 at 75 Hz refresh (QXGA)
⎯ DDC2B compliant interface with Advanced Digital Display 2 or 2+
(ADD2/ADD2+) cards, support for TV-out/TV-in and DVI digital display
connections
⎯ Supports flat panels up to 2048 x 1536 at 60Hz or digital CRT/HDTV at
1920 x 1080 at 85 Hz (with ADD2/ADD2+)
•
•
⎯ Two multiplexed DVO port interfaces with 200 MHz pixel clocks using an
ADD2/ADD2+ card
Dynamic Video Memory Technology (DVMT) support up to 256 MB
Intel® Zoom Utility
For information about
Refer to
Obtaining graphics software and utilities
Section 1.2, page 15
1.5.1.2
Dynamic Video Memory Technology (DVMT)
DVMT enables enhanced graphics and memory performance through Direct AGP, and
highly efficient memory utilization. DVMT ensures the most efficient use of available
system memory for maximum 2-D/3-D graphics performance. Up to 256 MB of
system memory can be allocated to DVMT on systems that have 512 MB or more of
total system memory installed. Up to 128 MB can be allocated to DVMT on systems
that have 256 MB but less than 512 MB of total installed system memory. Up to 64
MB can be allocated to DVMT when less than 256 MB of system memory is installed.
DVMT returns system memory back to the operating system when the additional
system memory is no longer required by the graphics subsystem.
18
Product Description
DVMT will always use a minimal fixed portion of system physical memory (as set in the
BIOS Setup program) for compatibility with legacy applications. An example of this
would be when using VGA graphics under DOS. Once loaded, the operating system
and graphics drivers allocate additional system memory to the graphics buffer as
needed for performing graphics functions.
NOTE
The use of DVMT requires operating system driver support.
1.5.1.3
Configuration Modes
A list of supported modes for the Intel GMA950 graphics controller is available as a
downloadable document.
For information about
Refer to
Supported video modes for the board
Section 1.2, page 15
1.5.2
USB
The board supports up to eight USB 2.0 ports, supports UHCI and EHCI, and uses
UHCI- and EHCI-compatible drivers.
The ICH7 provides the USB controller for all ports. The port arrangement is as
follows:
•
•
Four ports are implemented with dual stacked back panel connectors
Four ports are routed to two separate front panel USB headers
NOTE
Computer systems that have an unshielded cable attached to a USB port may not
meet FCC Class B requirements, even if no device is attached to the cable. Use
shielded cable that meets the requirements for full-speed devices.
For information about
Refer to
The location of the USB connectors on the back panel
Figure 8, page 37
The location of the front panel USB headers
Figure 9, page 38
1.5.3
IDE Support
The board provides three IDE interface connectors:
•
•
One parallel ATA IDE connector that supports two devices
Two serial ATA IDE connectors that support one device per connector
19
Intel Desktop Board D945GCPE Technical Product Specification
1.5.3.1
Parallel ATE IDE Interface
The ICH7’s Parallel ATA IDE controller has one bus-mastering Parallel ATA IDE
interface. The Parallel ATA IDE interface supports the following modes:
•
•
•
•
•
Programmed I/O (PIO): processor controls data transfer.
8237-style DMA: DMA offloads the processor, supporting transfer rates of up to
16 MB/sec.
Ultra DMA: DMA protocol on IDE bus supporting host and target throttling and
transfer rates of up to 33 MB/sec.
ATA-66: DMA protocol on IDE bus supporting host and target throttling and
transfer rates of up to 66 MB/sec. ATA-66 protocol is similar to Ultra DMA and is
device driver compatible.
ATA-100: DMA protocol on IDE bus allows host and target throttling. The ICH7’s
ATA-100 logic can achieve read transfer rates up to 100 MB/sec and write transfer
rates up to 88 MB/sec.
NOTE
ATA-66 and ATA-100 are faster timings and require a specialized cable to reduce
reflections, noise, and inductive coupling.
The Parallel ATA IDE interface also supports ATAPI devices (such as CD-ROM drives)
and ATA devices using the transfer modes.
The BIOS supports Logical Block Addressing (LBA) and Extended Cylinder Head Sector
(ECHS) translation modes. The drive reports the transfer rate and translation mode to
the BIOS.
For information about
Refer to
The location of the Parallel ATA IDE connector
Figure 9, page 38
1.5.3.2
Serial ATA Interfaces
The ICH7’s Serial ATA controller offers two independent Serial ATA ports with a
theoretical maximum transfer rate of 3 Gbits/sec per port. One device can be installed
on each port for a maximum of two Serial ATA devices. A point-to-point interface is
used for host to device connections, unlike Parallel ATA IDE which supports a
master/slave configuration and two devices per channel.
For compatibility, the underlying Serial ATA functionality is transparent to the
operating system. The Serial ATA controller can operate in both legacy and native
modes. In legacy mode, standard IDE I/O and IRQ resources are assigned (IRQ 14
and 15). In Native mode, standard PCI Conventional bus resource steering is used.
Native mode is the preferred mode for configurations using the Windows* XP
operating system.
NOTE
Many Serial ATA drives use new low-voltage power connectors and require adaptors or
power supplies equipped with low-voltage power connectors.
For more information, see: http://www.serialata.org/
20
Product Description
For information about
Refer to
The location of the Serial ATA IDE connectors
Figure 9, page 38
1.5.4
Real-Time Clock, CMOS SRAM, and Battery
A coin-cell battery (CR2032) powers the real-time clock and CMOS memory. When
the computer is not plugged into a wall socket, the battery has an estimated life of
three years. When the computer is plugged in, the standby current from the power
supply extends the life of the battery. The clock is accurate to ± 13 minutes/year at
25 ºC with 3.3 VSB applied.
NOTE
If the battery and AC power fail, custom defaults, if previously saved, will be loaded
into CMOS RAM at power-on.
1.6
Legacy I/O Controller
The legacy I/O controller provides the following features:
•
•
•
•
•
Serial IRQ interface compatible with serialized IRQ support for PCI Conventional
bus systems
PS/2-style mouse and keyboard interfaces
Interface for one 1.44 MB diskette drive
Intelligent power management, including a programmable wake-up event interface
PCI Conventional bus power management support
The BIOS Setup program provides configuration options for the legacy I/O controller.
1.6.1
Diskette Drive Controller
The legacy I/O controller supports one diskette drive. Use the BIOS Setup program to
configure the diskette drive interface.
For information about
Refer to
The location of the diskette drive connector
Figure 9, page 38
1.6.2
Keyboard and Mouse Interface
PS/2 keyboard and mouse connectors are located on the back panel.
NOTE
The keyboard is supported in the bottom PS/2 connector and the mouse is supported
in the top PS/2 connector. Power to the computer should be turned off before a
keyboard or mouse is connected or disconnected.
For information about
Refer to
The location of the keyboard and mouse connectors
Figure 8, page 37
21
Intel Desktop Board D945GCPE Technical Product Specification
1.7
Audio Subsystem
The board supports the Intel High Definition audio subsystem based on the Realtek
ALC662 audio codec. The audio subsystem supports the following features:
•
•
•
Line out and Mic in functions for front panel audio jacks
A signal-to-noise (S/N) ratio of 95 dB
Independent stereo audio playback from back panel connectors and Intel® High
Definition audio front panel audio header.
NOTE
The use of AC 97 front panel audio headers is not recommended if you plan to obtain
Microsoft Windows Vista certification.
1.7.1
Audio Subsystem Software
Audio software and drivers are available from Intel’s World Wide Web site.
For information about
Refer to
Obtaining audio software and drivers
Section 1.2, page 15
1.7.2
Audio Connectors
The board contains audio connectors/headers on both the back panel and the
component side of the board. The front panel audio header provides mic in and line
out signals for the front panel.
For information about
Refer to
The location of the front panel audio header
Figure 9, page 38
The signal names of the front panel audio header
Table 9, page 40
The back panel audio connectors
Section 2.2.1, page 37
1.7.3
Four Channel Audio Subsystem
The four channel High Definition audio subsystem includes the following:
•
•
•
Intel 82801GB I/O Controller Hub (ICH7)
Realtek ALC662 audio codec
Microphone input that supports a single dynamic, condenser, or electret
microphone
The back panel audio connectors are configurable through the audio device drivers.
The available configurable audio ports are shown in Figure 3.
22
Product Description
Item
Description
A
Line in
B
Line out
C
Mic in
Figure 3. Back Panel Audio Connector Options
For information about
Refer to
The back panel audio connectors
Section 2.2.1, page 37
1.8
LAN Subsystem
The LAN subsystem consists of the following:
•
•
•
Intel 82801GB ICH7
Realtek RTL8101E-GR device for 10/100 Mbits/sec Ethernet LAN connectivity
RJ-45 LAN connector with integrated status LEDs
Additional features of the LAN subsystem include:
•
•
•
CSMA/CD protocol engine
LAN connect interface that supports the 82562G
PCI Conventional bus power management
⎯ Supports ACPI technology
⎯ Supports LAN wake capabilities
1.8.1
LAN Subsystem Software
LAN software and drivers are available from Intel’s World Wide Web site.
For information about
Refer to
Obtaining LAN software and drivers
Section 1.2, page 15
23
Intel Desktop Board D945GCPE Technical Product Specification
1.8.2
Realtek RTL8101E-GR Fast Ethernet Controller
The Realtek RTL8101E-GR provides the following functions:
•
•
•
•
10/100 Ethernet LAN connectivity
Full device driver compatibility
Programmable transit threshold
Configuration EEPROM that contains the MAC address
1.8.2.1
RJ-45 LAN Connector with Integrated LEDs
Two LEDs are built into the RJ-45 LAN connector (shown in Figure 4).
Figure 4. LAN Connector LED Locations
Table 4 describes the LED states when the board is powered up and the
10/100 Mbits/sec LAN subsystem is operating.
Table 4. LAN Connector LED States
LED
A
B
24
LED Color
Green
Yellow
LED State
Condition
Off
LAN link is not established.
On
LAN link is established.
Blinking
LAN activity is occurring.
Off
10 Mbits/sec data rate is selected.
On
100 Mbits/sec data rate is selected.
Product Description
1.9
Hardware Management Subsystem
The hardware management features enable the board to be compatible with the Wired
for Management (WfM) specification. The board has several hardware management
features, including the following:
•
•
•
1.9.1
Chassis intrusion detection
Fan monitoring and control (through the ITE 8718F/GX I/O Controller)
Thermal and voltage monitoring
Hardware Monitoring and Fan Control
The features of the hardware monitoring and fan control ASIC include:
•
•
•
•
•
Internal ambient temperature sensor
Two remote thermal diode sensors for direct monitoring of processor temperature
and ambient temperature sensing
Power supply monitoring of five voltages (+5 V, +12 V, +3.3 VSB, +1.5 V, and
+VCCP) to detect levels above or below acceptable values
Thermally monitored closed-loop fan control, for both fans, that can adjust the fan
speed or switch the fans on or off as needed
SMBus interface
For information about
Refer to
The location of the fan headers and sensors for thermal monitoring
Figure 5, page 26
1.9.2
Chassis Intrusion and Detection
The board supports a chassis security feature that detects if the chassis cover is
removed. The security feature uses a mechanical switch on the chassis that attaches
to the chassis intrusion header. When the chassis cover is removed, the mechanical
switch is in the closed position.
1.9.3
Fan Monitoring
Fan monitoring can be implemented using third-party software. The level of
monitoring and control is dependent on the I/O controller used with the board.
For information about
Refer to
The functions of the fan headers
Section 1.10.2.2, page 30
25
Intel Desktop Board D945GCPE Technical Product Specification
1.9.4
Thermal Monitoring
Figure 5 shows the location of the sensors and fan headers.
Item
Description
A
Rear chassis fan
B
Thermal diode, located on processor die
C
Processor fan
Figure 5. Thermal Sensors and Fan Headers
26
Product Description
1.10 Power Management
Power management is implemented at several levels, including:
•
•
Software support through Advanced Configuration and Power Interface (ACPI)
Hardware support:
⎯ Power connector
⎯ Fan headers
⎯ LAN wake capabilities
⎯ Instantly Available PC technology
⎯ Wake from USB
⎯ Wake from PS/2 devices
⎯ Power Management Event signal (PME#) wake-up support
1.10.1
ACPI
ACPI gives the operating system direct control over the power management and Plug
and Play functions of a computer. The use of ACPI with this board requires an
operating system that provides full ACPI support. ACPI features include:
•
•
•
•
•
•
Plug and Play (including bus and device enumeration)
Power management control of individual devices, add-in boards (some add-in
boards may require an ACPI-aware driver), video displays, and hard disk drives
Methods for achieving less than 15-watt system operation in the power-on/standby
sleeping state
A Soft-off feature that enables the operating system to power-off the computer
Support for multiple wake-up events (see Table 7 on page 29)
Support for a front panel power and sleep mode switch
Table 5 lists the system states based on how long the power switch is pressed,
depending on how ACPI is configured with an ACPI-aware operating system.
Table 5. Effects of Pressing the Power Switch
If the system is in this
…and the power switch is
state…
pressed for
…the system enters this state
Off
(ACPI G2/G5 – Soft off)
Less than four seconds
Power-on
(ACPI G0 – working state)
On
(ACPI G0 – working state)
Less than four seconds
Soft-off/Standby
(ACPI G1 – sleeping state)
On
(ACPI G0 – working state)
More than four seconds
Fail safe power-off
(ACPI G2/G5 – Soft off)
Sleep
(ACPI G1 – sleeping state)
Less than four seconds
Wake-up
(ACPI G0 – working state)
Sleep
(ACPI G1 – sleeping state)
More than four seconds
Power-off
(ACPI G2/G5 – Soft off)
27
Intel Desktop Board D945GCPE Technical Product Specification
1.10.1.1
System States and Power States
Under ACPI, the operating system directs all system and device power state
transitions. The operating system puts devices in and out of low-power states based
on user preferences and knowledge of how devices are being used by applications.
Devices that are not being used can be turned off. The operating system uses
information from applications and user settings to put the system as a whole into a
low-power state.
Table 6 lists the power states supported by the board along with the associated
system power targets. See the ACPI specification for a complete description of the
various system and power states.
Table 6. Power States and Targeted System Power
Global States
Sleeping States
Processor
States
Device States
Targeted System
Power (Note 1)
G0 – working
state
S0 – working
C0 – working
D0 – working state.
Full power > 30 W
G1 – sleeping
state
S1 – Processor
stopped
C1 – stop
grant
D1, D2, D3 – device
specification
specific.
5 W < power < 52.5 W
G1 – sleeping
state
S3 – Suspend to
RAM. Context
saved to RAM.
No power
D3 – no power
except for wake-up
logic.
Power < 5 W (Note 2)
G1 – sleeping
state
S4 – Suspend to
disk. Context
saved to disk.
No power
D3 – no power
except for wake-up
logic.
Power < 5 W (Note 2)
G2/S5
S5 – Soft off.
Context not saved.
Cold boot is
required.
No power
D3 – no power
except for wake-up
logic.
Power < 5 W (Note 2)
G3 –
mechanical off
No power to the
system.
No power
D3 – no power for
wake-up logic,
except when
provided by battery
or external source.
No power to the system.
Service can be
performed safely.
AC power is
disconnected
from the
computer.
Notes:
1.
Total system power is dependent on the system configuration, including add-in boards and peripherals
powered by the system chassis’ power supply.
2.
Dependent on the standby power consumption of wake-up devices used in the system.
1.10.1.2 ENERGY STAR*
In 2007, the US Department of Energy and the US Environmental Protection Agency
revised the ENERGY STAR* requirements. Intel has worked directly with these two
governmental agencies to define the new requirements. Currently Intel® Desktop
Boards meet the new requirements.
28
For information about
Refer to
ENERGY STAR requirements and recommended configurations
http://www.intel.com/go/energystar
Product Description
1.10.1.3
Wake-up Devices and Events
Table 7 lists the devices or specific events that can wake the computer from specific
states.
Table 7. Wake-up Devices and Events
These devices/events can wake up the computer…
…from this state
LAN
S1, S3, S4, S5 (Note)
PME# signal
S1, S3, S4 (LAN only), S5 (LAN only) (Note)
Power switch
S1, S3, S4, S5
PS/2 devices
S1, S3
RTC alarm
S1, S3, S4, S5
USB
S1, S3
WAKE# signal
S1, S3, S4, S5
Note:
For LAN and PME# signal, S5 is disabled by default in the BIOS Setup program. Setting this option
to Power On will enable a wake-up event from LAN in the S5 state.
NOTE
The use of these wake-up events from an ACPI state requires an operating system
that provides full ACPI support. In addition, software, drivers, and peripherals must
fully support ACPI wake events.
1.10.2
Hardware Support
CAUTION
Ensure that the power supply provides adequate +5 V standby current if LAN wake
capabilities and Instantly Available PC technology features are used. Failure to do so
can damage the power supply. The total amount of standby current required depends
on the wake devices supported and manufacturing options.
The board provides several power management hardware features, including:
•
•
•
•
•
•
•
Power connector
Fan headers
LAN wake capabilities
Instantly Available PC technology
Wake from USB
Wake from PS/2 keyboard
PME# signal wake-up support
LAN wake capabilities and Instantly Available PC technology require power from the
+5 V standby line.
29
Intel Desktop Board D945GCPE Technical Product Specification
NOTE
The use of Wake from USB from an ACPI state requires an operating system that
provides full ACPI support.
1.10.2.1
Power Connector
ATX12V-compliant power supplies can turn off the system power through system
control. When an ACPI-enabled system receives the correct command, the power
supply removes all non-standby voltages.
When resuming from an AC power failure, the computer returns to the power state it
was in before power was interrupted (on or off). The computer’s response can be set
using the Last Power State feature in the BIOS Setup program’s Boot menu.
For information about
Refer to
The location of the main power connector
Figure 9, page 38
The signal names of the main power connector
Table 15, page 41
1.10.2.2
Fan Headers
The function/operation of the fan headers is as follows:
•
•
•
•
•
30
The fans are on when the board is in the S0 or S1 state.
The fans are off when the board is off or in the S3, S4, or S5 state.
Each fan header is wired to a fan tachometer input of the Legacy I/O controller for
hardware monitoring and fan control.
All fan headers support closed-loop fan control that can adjust the fan speed or
switch the fan on or off as needed.
All fan headers have a +12 V DC connection.
For information about
Refer to
The location of the fan headers
Figure 9, page 38
The location of the fan headers and sensors for thermal monitoring
Figure 5, page 26
The signal names of the processor fan header
Table 13, page 40
The signal names of the chassis fan header
Table 14, page 41
Product Description
1.10.2.3
LAN Wake Capabilities
CAUTION
For LAN wake capabilities, the +5 V standby line for the power supply must be capable
of providing adequate +5 V standby current. Failure to provide adequate standby
current when implementing LAN wake capabilities can damage the power supply.
LAN wake capabilities enable remote wake-up of the computer through a network.
The LAN network adapter monitors network traffic at the Media Independent Interface.
Upon detecting a Magic Packet* frame, the LAN subsystem asserts a wake-up signal
that powers up the computer. Depending on the LAN implementation, the board
supports LAN wake capabilities with ACPI in the following ways:
•
•
The PCI Conventional bus PME# signal for PCI 2.3 compliant LAN designs
The onboard LAN subsystem
1.10.2.4
Instantly Available PC Technology
CAUTION
For Instantly Available PC technology, the +5 V standby line for the power supply
must be capable of providing adequate +5 V standby current. Failure to provide
adequate standby current when implementing Instantly Available PC technology can
damage the power supply.
Instantly Available PC technology enables the board to enter the ACPI S3 (Suspend-toRAM) sleep-state. While in the S3 sleep-state, the computer will appear to be off (the
power supply is off, and the front panel LED is amber if dual colored, or off if single
colored.) When signaled by a wake-up device or event, the system quickly returns to
its last known wake state. Table 7 on page 29 lists the devices and events that can
wake the computer from the S3 state.
The board supports the PCI Bus Power Management Interface Specification. Add-in
boards that also support this specification can participate in power management and
can be used to wake the computer.
The use of Instantly Available PC technology requires operating system support and
PCI 2.3 compliant add-in cards and drivers.
31
Intel Desktop Board D945GCPE Technical Product Specification
1.10.2.5
Wake from USB
USB bus activity wakes the computer from ACPI S1 or S3 states.
NOTE
Wake from USB requires the use of a USB peripheral that supports Wake from USB.
1.10.2.6
Wake from PS/2 Devices
PS/2 device activity wakes the computer from an ACPI S1 or S3 state.
1.10.2.7
PME# Signal Wake-up Support
When the PME# signal on the PCI Conventional bus is asserted, the computer wakes
from an ACPI S1, S3, S4 (LAN only), or S5 (LAN only) state (with Wake on PME
enabled in BIOS).
1.10.2.8
+5 V Standby Power Indicator LED
The +5 V standby power indicator LED shows that power is still present even when the
computer appears to be off. Figure 6 shows the location of the standby power
indicator LED.
CAUTION
If AC power has been switched off and the standby power indicator is still lit,
disconnect the power cord before installing or removing any devices connected to the
board. Failure to do so could damage the board and any attached devices.
Figure 6. Location of the Standby Power Indicator LED
32
2
Technical Reference
What This Chapter Contains
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
Memory Resources .......................................................................... 34
Connectors and Headers................................................................... 36
Jumper Block .................................................................................. 46
Mechanical Considerations ................................................................ 48
Electrical Considerations ................................................................... 49
Thermal Considerations .................................................................... 50
Reliability ....................................................................................... 52
Environmental ................................................................................ 53
33
Intel Desktop Board D945GCPE Technical Product Specification
2.1
2.1.1
Memory Resources
Addressable Memory
The board utilizes 2 GB of addressable system memory. Typically the address space
that is allocated for PCI Conventional bus add-in cards, BIOS (SPI Flash), and chipset
overhead resides above the top of DRAM (total system memory). On a system that
has 2 GB of system memory installed, it is not possible to use all of the installed
memory due to system address space being allocated for other system critical
functions. These functions include the following:
•
•
•
•
•
•
•
34
BIOS/ SPI Flash (4 MB)
Local APIC (19 MB)
Digital Media Interface (40 MB)
Front side bus interrupts (17 MB)
PCI Express configuration space (256 MB)
GMCH base address registers and internal graphics ranges
Memory-mapped I/O that is dynamically allocated for PCI Conventional add-in
cards
Technical Reference
The amount of installed memory that can be used will vary based on add-in cards and
BIOS settings. Figure 7 shows a schematic of the system memory map. All installed
system memory can be used when there is no overlap of system addresses.
Figure 7. Detailed System Memory Address Map
35
Intel Desktop Board D945GCPE Technical Product Specification
2.2
Connectors and Headers
CAUTION
Only the following connectors and headers have overcurrent protection: back panel
USB, front panel USB, and PS/2.
The other internal connectors/headers are not overcurrent protected and should
connect only to devices inside the computer’s chassis, such as fans and internal
peripherals. Do not use these connectors/headers to power devices external to the
computer’s chassis. A fault in the load presented by the external devices could cause
damage to the computer, the power cable, and the external devices themselves.
This section describes the board’s connectors and headers. The connectors and
headers can be divided into these groups:
•
•
36
Back panel connectors (see page 37)
Component-side connectors and headers (see page 38)
Technical Reference
2.2.1
Back Panel Connectors
Figure 8 shows the location of the back panel connectors.
Item
Description
A
PS/2 mouse port
B
PS/2 keyboard port
C
VGA port
D
USB ports [4]
E
LAN
F
Audio line in
G
Mic in
H
Audio line out
Figure 8. Back Panel Connectors
NOTE
The back panel audio line out connector is designed to power headphones or amplified
speakers only. Poor audio quality occurs if passive (non-amplified) speakers are
connected to this output.
37
Intel Desktop Board D945GCPE Technical Product Specification
2.2.2
Component-side Connectors and Headers
Figure 9 shows the locations of the component-side connectors and headers.
Figure 9. Component-side Connectors and Headers
38
Technical Reference
Table 8 lists the component-side connectors and headers identified in Figure 9.
Table 8. Component-side Connectors and Headers Shown in Figure 9
Item/callout
from Figure 9
Description
A
Front panel audio header
B
PCI Conventional bus add-in card connector 2
C
PCI Conventional bus add-in card connector 1
D
Rear chassis fan header
E
Processor core power connector (2 X 2)
F
Processor fan header
G
Main power connector (2 X 12)
H
Diskette drive connector
I
Parallel ATA IDE connector
J
Serial ATA connector 1
K
Serial ATA connector 0
L
Auxiliary front panel power LED header
M
Front panel header
N
Chassis intrusion header
O
Front panel USB header
P
Front panel USB header
Q
Serial port header
39
Intel Desktop Board D945GCPE Technical Product Specification
Table 9. Front Panel Audio Header
#
Pin
Signal Name
Pin
Signal Name
1
Port E [Port 1] Left Channel
2
Ground
3
Port E [Port 1] Right Channel
4
Presence# (dongle present)
5
Port F [Port 2] Right Channel
6
Port E [Port 1] Sense return
(jack detection)
7
Port E [Port 1] and Port F [Port 2]
Sense send (jack detection)
8
Key
9
Port F [Port 2] Left Channel
10
Port F [Port 2] Sense return
(jack detection)
INTEGRATOR’S NOTE
The front panel audio header is colored yellow.
Table 10. Chassis Intrusion Header
Pin
Signal Name
1
Intruder
2
Ground
Table 11. Serial ATA Connectors
Pin
Signal Name
1
Ground
2
TXP
3
TXN
4
Ground
5
RXN
6
RXP
7
Ground
Table 12. Serial Port Header
40
Pin
Signal Name
Pin
Signal Name
1
DCD
2
RXD#
3
TXD#
4
DTR
5
Ground
6
DSR
7
RTS
8
CTS
9
RI
10
Key (no pin)
Technical Reference
Table 13. Processor Fan Header
Pin
Signal Name
1
Ground
2
+12 V
3
FAN_TACH
4
FAN_CONTROL
Table 14. Chassis Fan Header
Pin
Signal Name
1
FAN_CONTROL
2
+12 V
3
FAN_TACH
2.2.2.1
Power Supply Connectors
The board has the following power supply connectors:
•
•
Main power – a 2 x 12 connector. This connector is compatible with 2 x 10
connectors previously used on Intel Desktop boards. The board supports the use
of ATX12V power supplies with either 2 x 10 or 2 x 12 main power cables. When
using a power supply with a 2 x 10 main power cable, attach that cable on the
rightmost pins of the main power connector, leaving pins 11, 12, 23, and 24
unconnected.
Processor core power – a 2 x 2 connector. This connector provides power
directly to the processor voltage regulator and must always be used. Failure to do
so will prevent the board from booting.
Table 15. Main Power Connector
Pin
Signal Name
Pin
Signal Name
1
+3.3 V
13
+3.3 V
2
+3.3 V
14
-12 V
3
Ground
15
Ground
4
+5 V
16
PS-ON# (power supply remote on/off)
5
Ground
17
Ground
6
+5 V
18
Ground
7
Ground
19
Ground
8
PWRGD (Power Good)
20
No connect
9
+5 V (Standby)
21
+5 V
10
+12 V
22
+5 V
11
+12 V (Note)
23
+5 V (Note)
12
2 x 12 connector detect (Note)
24
Ground (Note)
Note: When using a 2 x 10 power supply cable, this pin will be unconnected.
41
Intel Desktop Board D945GCPE Technical Product Specification
Table 16. Processor Core Power Connector
Pin
Signal Name
Pin
Signal Name
1
Ground
2
Ground
3
+12 V
4
+12 V
2.2.2.2
Add-in Card Connectors
The board has the following add-in card connectors:
•
PCI Conventional (rev 2.3 compliant) bus: two PCI Conventional bus add-in card
connectors. The SMBus is routed to all PCI Conventional bus connectors. PCI
Conventional bus add-in cards with SMBus support can access sensor data and
other information residing on the board.
Note the following considerations for the PCI Conventional bus connectors:
•
•
All of the PCI Conventional bus connectors are bus master capable.
SMBus signals are routed to all PCI Conventional bus connectors. This enables PCI
Conventional bus add-in boards with SMBus support to access sensor data on the
boards. The specific SMBus signals are as follows:
⎯ The SMBus clock line is connected to pin A40.
⎯ The SMBus data line is connected to pin A41.
2.2.2.3
Auxiliary Front Panel Power/Sleep LED Header
Pins 1 and 3 of this header duplicate the signals on pins 2 and 4 of the front panel
header.
Table 17. Auxiliary Front Panel Power/Sleep LED Header
42
Pin
Signal Name
In/Out
Description
1
HDR_BLNK_GRN
Out
Front panel green LED
2
Not connected
3
HDR_BLNK_YEL
Out
Front panel yellow LED
Technical Reference
2.2.2.4
Front Panel Header
This section describes the functions of the front panel header. Table 18 lists the signal
names of the front panel header. Figure 10 is a connection diagram for the front panel
header.
Table 18. Front Panel Header
In/
Pin
Signal
Out
In/
Description
Pin
Signal
Out
Hard Drive Activity LED
[Yellow]
Description
Power LED
[Green]
1
HD_PWR
Out
Hard disk LED
pull-up to +5 V
2
HDR_BLNK_
GRN
Out
Front panel green
LED
3
HDA#
Out
Hard disk active
LED
4
HDR_BLNK_
YEL
Out
Front panel yellow
LED
Reset Switch
[Purple]
5
Ground
7
FP_RESET#
In
On/Off Switch
[Red]
Ground
6
FPBUT_IN
Reset switch
8
Ground
Power
9
+5 V
In
Power switch
Ground
Not Connected
Power
10
N/C
Not connected
Figure 10. Connection Diagram for Front Panel Header
43
Intel Desktop Board D945GCPE Technical Product Specification
2.2.2.4.1
Hard Drive Activity LED Header [Yellow]
Pins 1 and 3 [Yellow] can be connected to an LED to provide a visual indicator that
data is being read from or written to a hard drive. Proper LED function requires one of
the following:
•
•
A Serial ATA hard drive connected to an onboard Serial ATA connector
An IDE hard drive connected to an onboard IDE connector
2.2.2.4.2
Reset Switch Header [Purple]
Pins 5 and 7 [Purple] can be connected to a momentary single pole, single throw
(SPST) type switch that is normally open. When the switch is closed, the board resets
and runs the POST.
2.2.2.4.3
Power/Sleep LED Header [Green]
Pins 2 and 4 [Green] can be connected to a one- or two-color LED. Table 19 shows
the possible states for a one-color LED. Table 20 shows the possible states for a twocolor LED.
Table 19. States for a One-Color Power LED
LED State
Description
Off
Power off/sleeping
Steady Green
Running
Table 20. States for a Two-Color Power LED
LED State
Description
Off
Power off
Steady Green
Running
Steady Yellow
Sleeping
NOTE
The colors listed in Table 19 and Table 20 are suggested colors only. Actual LED
colors are product- or customer-specific.
2.2.2.4.4
Power Switch Header [Red]
Pins 6 and 8 [Red] can be connected to a front panel momentary-contact power
switch. The switch must pull the SW_ON# pin to ground for at least 50 ms to signal
the power supply to switch on or off. (The time requirement is due to internal
debounce circuitry on the board.) At least two seconds must pass before the power
supply will recognize another on/off signal.
44
Technical Reference
2.2.2.5
Front Panel USB Headers
Figure 11 is a connection diagram for the front panel USB headers.
#
INTEGRATOR’S NOTES
•
•
•
•
The +5 V DC power on the USB headers is fused.
Pins 1, 3, 5, and 7 comprise one USB port.
Pins 2, 4, 6, and 8 comprise one USB port.
Use only a front panel USB connector that conforms to the USB 2.0 specification
for high-speed USB devices.
Figure 11. Connection Diagram for Front Panel USB Headers
45
Intel Desktop Board D945GCPE Technical Product Specification
2.3
Jumper Block
CAUTION
Do not move the jumper with the power on. Always turn off the power and unplug the
power cord from the computer before changing a jumper setting. Otherwise, the
board could be damaged.
Figure 12 shows the location of the jumper block. The jumper block determines the
BIOS Setup program’s mode. Table 21 describes the jumper settings for the three
modes: normal, configure, and recovery. When the jumper is set to configure mode
and the computer is powered-up, the BIOS compares the processor version and the
microcode version in the BIOS and reports if the two match.
Figure 12. Location of the Jumper Block
46
Technical Reference
Table 21. BIOS Setup Configuration Jumper Settings
Function/Mode
Jumper Setting
Configuration
1-2
The BIOS uses current configuration information and
passwords for booting.
2-3
After the POST runs, Setup runs automatically. The
maintenance menu is displayed.
None
The BIOS attempts to recover the BIOS configuration. A
recovery diskette is required.
Normal
Configure
Recovery
47
Intel Desktop Board D945GCPE Technical Product Specification
2.4
2.4.1
Mechanical Considerations
Form Factor
The board is designed to fit into an ATX- or microATX-form-factor chassis. Figure 13
illustrates the mechanical form factor of the board. Dimensions are given in inches
[millimeters]. The outer dimensions are 8.60 inches by 9.60 inches [218.44
millimeters by 243.84 millimeters]. Location of the I/O connectors and mounting
holes are in compliance with the ATX specification.
Figure 13. Board Dimensions
48
Technical Reference
2.5
Electrical Considerations
2.5.1
Power Supply Considerations
CAUTION
The +5 V standby line from the power supply must be capable of providing adequate
+5 V standby current. Failure to do so can damage the power supply. The total
amount of standby current required depends on the wake devices supported and
manufacturing options.
Additional power required will depend on configurations chosen by the integrator.
The power supply must comply with the indicated parameters of the ATX form factor
specification.
• The potential relation between 3.3 VDC and +5 VDC power rails
• The current capability of the +5 VSB line
• All timing parameters
• All voltage tolerances
For example, for a system consisting of a supported 65 W processor (see section 1.3
on page 15 for a list of supported processors), 1 GB DDR2 RAM, one hard disk drive,
one optical drive, and all board peripherals enabled, the minimum recommended
power supply is 200 W. Table 22 lists the recommended power supply current values.
Table 22. Recommended Power Supply Current Values
Output Voltage
3.3 V
5V
12 V1
12 V2
-12 V
5 VSB
Current
8.1 A
9.3 A
0.9 A
8.2 A
0.3 A
0.2 A
For information
about
Refer to
Selecting an appropriate
power supply
http://support.intel.com/support/motherboards/desktop/sb/CS-026472.htm
49
Intel Desktop Board D945GCPE Technical Product Specification
2.5.2
Fan Header Current Capability
CAUTION
The processor fan must be connected to the processor fan header, not to a chassis fan
header. Connecting the processor fan to a chassis fan header may result in onboard
component damage that will halt fan operation.
Table 23 lists the current capability of the fan headers.
Table 23. Fan Header Current Capability
Fan Header
Maximum Available Current
Processor fan
2.0 A
Chassis fan
1.5 A
2.5.3
Add-in Board Considerations
The board is designed to provide 2 A (average) of +5 V current for each add-in board.
The total +5 V current draw for add-in boards for a fully loaded board (both expansion
slots filled) must not exceed 6 A.
2.6
Thermal Considerations
CAUTION
A chassis with a maximum internal ambient temperature of 38 oC at the processor fan
inlet is a requirement. Use a processor heatsink that provides omni-directional airflow
to maintain required airflow across the processor voltage regulator area.
CAUTION
Failure to ensure appropriate airflow may result in reduced performance of both the
processor and/or voltage regulator or, in some instances, damage to the board. For a
list of chassis that have been tested with Intel desktop boards please refer to the
following website:
http://developer.intel.com/design/motherbd/cooling.htm
All responsibility for determining the adequacy of any thermal or system design
remains solely with the reader. Intel makes no warranties or representations that
merely following the instructions presented in this document will result in a system
with adequate thermal performance.
50
Technical Reference
CAUTION
Ensure that the ambient temperature does not exceed the board’s maximum operating
temperature. Failure to do so could cause components to exceed their maximum case
temperature and malfunction. For information about the maximum operating
temperature, see the environmental specifications in Section 2.8.
CAUTION
Ensure that proper airflow is maintained in the processor voltage regulator circuit.
Failure to do so may result in damage to the voltage regulator circuit. The processor
voltage regulator area (item A in Figure 14) can reach a temperature of up to 85 oC in
an open chassis.
Figure 14 shows the locations of the localized high temperature zones.
Item
Description
A
B
C
D
Processor voltage regulator area
Processor
Intel 82945GC GMCH
Intel 82801GB ICH7
Figure 14. Localized High Temperature Zones
51
Intel Desktop Board D945GCPE Technical Product Specification
Table 24 provides maximum case temperatures for the components that are sensitive
to thermal changes. The operating temperature, current load, or operating frequency
could affect case temperatures. Maximum case temperatures are important when
considering proper airflow to cool the board.
Table 24. Thermal Considerations for Components
2.7
Component
Maximum Case Temperature
Processor
For processor case temperature, see processor datasheets and
processor specification updates
Intel 82945GC GMCH
99 oC (under bias)
Intel 82801GB ICH7
110 oC (under bias, without heatsink)
99 oC (under bias, with heatsink)
For information about
Refer to
Processor datasheets and specification updates
Section 1.2, page 15
Reliability
The Mean Time Between Failures (MTBF) prediction is calculated using component and
subassembly random failure rates. The calculation is based on the Bellcore Reliability
Prediction Procedure, TR-NWT-000332, Issue 4, September 1991. The MTBF
prediction is used to estimate repair rates and spare parts requirements.
The MTBF data is calculated from predicted data at 55 ºC. The MTBF for the
D945GCPE board is 57,845 hours.
52
Technical Reference
2.8
Environmental
Table 25 lists the environmental specifications for the board.
Table 25. Environmental Specifications
Parameter
Specification
Temperature
Non-Operating
-40 °C to +70 °C
Operating
0 °C to +55 °C
Shock
Unpackaged
50 g trapezoidal waveform
Packaged
Half sine 2 millisecond
Velocity change of 170 inches/second²
Product Weight (pounds)
Free Fall (inches)
Velocity Change
(inches/sec²)
<20
36
167
21-40
30
152
41-80
24
136
81-100
18
118
Vibration
Unpackaged
5 Hz to 20 Hz: 0.01 g² Hz sloping up to 0.02 g² Hz
20 Hz to 500 Hz: 0.02 g² Hz (flat)
Packaged
5 Hz to 40 Hz: 0.015 g² Hz (flat)
40 Hz to 500 Hz: 0.015 g² Hz sloping down to 0.00015 g² Hz
53
Intel Desktop Board D945GCPE Technical Product Specification
54
3
Overview of BIOS Features
What This Chapter Contains
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.1
Introduction ...................................................................................
BIOS Flash Memory Organization .......................................................
Resource Configuration ....................................................................
System Management BIOS (SMBIOS).................................................
BIOS Updates .................................................................................
Legacy USB Support ........................................................................
Boot Options...................................................................................
Adjusting Boot Speed.......................................................................
BIOS Security Features ....................................................................
55
56
56
57
58
59
59
61
62
Introduction
The boards use an Intel BIOS that is stored in the Serial Peripheral Interface Flash
Memory (SPI Flash) and can be updated using a disk-based program. The SPI Flash
contains the BIOS Setup program, POST, the PCI auto-configuration utility, and Plug
and Play support.
The BIOS displays a message during POST identifying the type of BIOS and a revision
code. The initial production BIOSs are identified as PE94510M.86A.
When the BIOS Setup configuration jumper is set to configure mode and the computer
is powered-up, the BIOS compares the processor version and the microcode version in
the BIOS and reports if the two match.
The BIOS Setup program can be used to view and change the BIOS settings for the
computer. The BIOS Setup program is accessed by pressing the <F2> key after the
Power-On Self-Test (POST) memory test begins and before the operating system boot
begins. The menu bar is shown below.
Maintenance Main
Advanced
Security
Power
Boot
Exit
NOTE
The maintenance menu is displayed only when the Desktop Board is in configure
mode. Section 2.3 on page 46 shows how to put the Desktop Board in configure mode.
55
Intel Desktop Board D945GCPE Technical Product Specification
Table 26 lists the BIOS Setup program menu features.
Table 26. BIOS Setup Program Menu Bar
Maintenance
Main
Advanced
Security
Power
Boot
Exit
Clears
Displays
Configures
Sets
Configures
Selects boot
Saves or
passwords and
processor
advanced
passwords
power
options
discards
displays
and memory
features
and security
management
changes to
processor
configuration
available
features
features and
Setup
through the
power supply
program
chipset
controls
options
information
Table 27 lists the function keys available for menu screens.
Table 27. BIOS Setup Program Function Keys
BIOS Setup Program Function Key
Description
<←> or <→>
Selects a different menu screen (Moves the cursor left or right)
<↑> or <↓>
Selects an item (Moves the cursor up or down)
<Tab>
Selects a field (Not implemented)
<Enter>
Executes command or selects the submenu
<F9>
Load the default configuration values for the current menu
<F10>
Save the current values and exits the BIOS Setup program
<Esc>
Exits the menu
3.2
BIOS Flash Memory Organization
The Serial Peripheral Interface Flash Memory (SPI Flash) includes a 4 Mbit (512 KB)
flash memory device.
3.3
3.3.1
Resource Configuration
PCI Autoconfiguration
The BIOS can automatically configure PCI devices. PCI devices may be onboard or
add-in cards. Autoconfiguration lets a user insert or remove PCI cards without having
to configure the system. When a user turns on the system after adding a PCI card,
the BIOS automatically configures interrupts, the I/O space, and other system
resources. Any interrupts set to Available in Setup are considered to be available for
use by the add-in card.
56
Overview of BIOS Features
3.3.2
PCI IDE Support
If you select Auto in the BIOS Setup program, the BIOS automatically sets up the
PCI IDE connector with independent I/O channel support. The IDE interface supports
hard drives up to ATA-66/100 and recognizes any ATAPI compliant devices, including
CD-ROM drives, tape drives, and Ultra DMA drives. The interface also supports
second-generation SATA drives. The BIOS determines the capabilities of each drive
and configures them to optimize capacity and performance. To take advantage of the
high capacities typically available today, hard drives are automatically configured for
Logical Block Addressing (LBA) and to PIO Mode 3 or 4, depending on the capability of
the drive. You can override the auto-configuration options by specifying manual
configuration in the BIOS Setup program.
To use ATA-66/100 features the following items are required:
•
•
•
An ATA-66/100 peripheral device
An ATA-66/100 compatible cable
ATA-66/100 operating system device drivers
NOTE
Do not connect an ATA device as a slave on the same IDE cable as an ATAPI master
device. For example, do not connect an ATA hard drive as a slave to an ATAPI
CD-ROM drive.
3.4
System Management BIOS (SMBIOS)
SMBIOS is a Desktop Management Interface (DMI) compliant method for managing
computers in a managed network.
The main component of SMBIOS is the Management Information Format (MIF)
database, which contains information about the computing system and its
components. Using SMBIOS, a system administrator can obtain the system types,
capabilities, operational status, and installation dates for system components. The
MIF database defines the data and provides the method for accessing this information.
The BIOS enables applications such as third-party management software to use
SMBIOS. The BIOS stores and reports the following SMBIOS information:
•
•
•
•
BIOS data, such as the BIOS revision level
Fixed-system data, such as peripherals, serial numbers, and asset tags
Resource data, such as memory size, cache size, and processor speed
Dynamic data, such as event detection and error logging
Non-Plug and Play operating systems require an additional interface for obtaining the
SMBIOS information. The BIOS supports an SMBIOS table interface for such operating
systems. Using this support, an SMBIOS service-level application running on a
non-Plug and Play operating system can obtain the SMBIOS information. Additional
board information can be found in the BIOS under the Additional Information header
under the Main BIOS page.
57
Intel Desktop Board D945GCPE Technical Product Specification
3.5
BIOS Updates
The BIOS can be updated using either of the following utilities, which are available on
the Intel World Wide Web site:
•
•
Intel® Express BIOS Update utility, which enables automated updating while in the
Windows environment. Using this utility, the BIOS can be updated from a file on a
hard disk, a 1.44 MB diskette, or a CD-ROM, or from the file location on the Web.
Intel® Flash Memory Update Utility, which requires creation of a boot diskette and
manual rebooting of the system. Using this utility, the BIOS can be updated from
a file on a 1.44 MB diskette (from a legacy diskette drive or an LS-120 diskette
drive) or a CD-ROM.
Both utilities verify that the updated BIOS matches the target system to prevent
accidentally installing an incompatible BIOS.
NOTE
Review the instructions distributed with the upgrade utility before attempting a BIOS
update.
For information about
Refer to
The Intel World Wide Web site
Section 1.2, page 15
3.5.1
Language Support
The BIOS Setup program and help messages are supported in US English. Additional
languages are available in the Integrator’s Toolkit utility. Check the Intel website for
details.
3.5.2
Custom Splash Screen
During POST, an Intel® splash screen is displayed by default. This splash screen can
be augmented with a custom splash screen. The Integrator’s Toolkit that is available
from Intel can be used to create a custom splash screen.
NOTE
If you add a custom splash screen, it will share space with the Intel branded logo.
58
For information about
Refer to
The Intel World Wide Web site
Section 1.2, page 15
Overview of BIOS Features
3.6
Legacy USB Support
Legacy USB support enables USB devices to be used even when the operating
system’s USB drivers are not yet available. Legacy USB support is used to access the
BIOS Setup program, and to install an operating system that supports USB.
Legacy USB support operates as follows:
1. When you apply power to the computer, legacy support is disabled.
2. POST begins.
3. Legacy USB support is enabled by the BIOS allowing you to use a USB keyboard to
enter and configure the BIOS Setup program and the maintenance menu.
4. POST completes.
5. The operating system loads. While the operating system is loading, USB
keyboards and mice are recognized and may be used to configure the operating
system.
6. After the operating system loads the USB drivers, all legacy and non-legacy USB
devices are recognized by the operating system, and Legacy USB support from the
BIOS is no longer used.
To install an operating system that supports USB, follow the operating system’s
installation instructions.
3.7
Boot Options
In the BIOS Setup program, the user can choose to boot from a diskette drive, hard
drives, CD-ROM, or the network. The default setting is for the diskette drive to be the
first boot device, the hard drive second, and the ATAPI CD-ROM third. The fourth
device is disabled.
3.7.1
CD-ROM Boot
Booting from CD-ROM is supported in compliance to the El Torito bootable CD-ROM
format specification. Under the Boot menu in the BIOS Setup program, ATAPI CDROM is listed as a boot device. Boot devices are defined in priority order. Accordingly,
if there is not a bootable CD in the CD-ROM drive, the system will attempt to boot
from the next defined drive.
3.7.2
Network Boot
The network can be selected as a boot device. This selection allows booting from the
onboard LAN or a network add-in card with a remote boot ROM installed.
Pressing the <F12> key during POST automatically forces booting from the LAN. To
use this key during POST, the User Access Level in the BIOS Setup program's Security
menu must be set to Full.
59
Intel Desktop Board D945GCPE Technical Product Specification
3.7.3
Booting Without Attached Devices
For use in embedded applications, the BIOS has been designed so that after passing
the POST, the operating system loader is invoked even if the following devices are not
present:
•
•
•
Video adapter
Keyboard
Mouse
3.7.4
Changing the Default Boot Device During POST
Pressing the <F10> key during POST causes a boot device menu to be displayed. This
menu displays the list of available boot devices (as set in the BIOS setup program’s
Boot Device Priority Submenu). Table 28 lists the boot device menu options.
Table 28. Boot Device Menu Options
60
Boot Device Menu Function Keys
Description
<↑> or <↓>
Selects a default boot device
<Enter>
Exits the menu, saves changes, and boots from the selected device
<Esc>
Exits the menu without saving changes
Overview of BIOS Features
3.8
Adjusting Boot Speed
These factors affect system boot speed:
•
•
3.8.1
Selecting and configuring peripherals properly
Optimized BIOS boot parameters
Peripheral Selection and Configuration
The following techniques help improve system boot speed:
•
•
•
•
3.8.2
Choose a hard drive with parameters such as “power-up to data ready” less than
eight seconds, that minimize hard drive startup delays.
Select a CD-ROM drive with a fast initialization rate. This rate can influence POST
execution time.
Eliminate unnecessary add-in adapter features, such as logo displays, screen
repaints, or mode changes in POST. These features may add time to the boot
process.
Try different monitors. Some monitors initialize and communicate with the BIOS
more quickly, which enables the system to boot more quickly.
BIOS Boot Optimizations
Use of the following BIOS Setup program settings reduces the POST execution time.
In the Boot Menu:
•
•
Set the hard disk drive as the first boot device. As a result, the POST does not
first seek a diskette drive, which saves about one second from the POST execution
time.
Disable Quiet Boot, which eliminates display of the logo splash screen. This could
save several seconds of painting complex graphic images and changing video
modes.
In the Peripheral Configuration submenu, disable the LAN device if it will not be used.
This can reduce up to four seconds of option ROM boot time.
NOTE
It is possible to optimize the boot process to the point where the system boots so
quickly that the Intel logo screen (or a custom logo splash screen) will not be seen.
Monitors and hard disk drives with minimum initialization times can also contribute to
a boot time that might be so fast that necessary logo screens and POST messages
cannot be seen.
This boot time may be so fast that some drives might be not be initialized at all. If
this condition should occur, it is possible to introduce a programmable delay ranging
from three to 30 seconds (using the Hard Disk Pre-Delay feature of the Advanced
Menu in the Drive Configuration Submenu of the BIOS Setup program).
61
Intel Desktop Board D945GCPE Technical Product Specification
3.9
BIOS Security Features
The BIOS includes security features that restrict access to the BIOS Setup program
and who can boot the computer. A supervisor password and a user password can be
set for the BIOS Setup program and for booting the computer, with the following
restrictions:
•
•
•
•
•
•
•
The supervisor password gives unrestricted access to view and change all the
Setup options in the BIOS Setup program. This is the supervisor mode.
The user password gives restricted access to view and change Setup options in the
BIOS Setup program. This is the user mode.
If only the supervisor password is set, pressing the <Enter> key at the password
prompt of the BIOS Setup program allows the user restricted access to Setup.
If both the supervisor and user passwords are set, users can enter either the
supervisor password or the user password to access Setup. Users have access to
Setup respective to which password is entered.
Setting the user password restricts who can boot the computer. The password
prompt will be displayed before the computer is booted. If only the supervisor
password is set, the computer boots without asking for a password. If both
passwords are set, the user can enter either password to boot the computer.
For enhanced security, use different passwords for the supervisor and user
passwords.
Valid password characters are A-Z, a-z, and 0-9. Passwords may be up to
16 characters in length.
Table 29 shows the effects of setting the supervisor password and user password.
This table is for reference only and is not displayed on the screen.
Table 29. Supervisor and User Password Functions
Password
Supervisor
Set
Mode
User Mode
Setup Options
Enter Setup
During Boot
Neither
Can change all
options (Note)
Can change all
options (Note)
None
None
None
Supervisor
only
Can change all
options
Can change a
Supervisor Password
limited number
of options
Supervisor
None
User only
N/A
Can change all
options
User
User
Supervisor
and user set
Can change all
options
Can change a
Supervisor Password
limited number Enter Password
of options
Supervisor or
user
Supervisor or
user
Note:
62
Password to
Enter Password
Clear User Password
If no password is set, any user can change all Setup options.
Password
4
Error Messages and Beep Codes
What This Chapter Contains
4.1 BIOS Front-panel Power LED Codes.................................................... 63
4.2 BIOS Error Messages ....................................................................... 63
4.3 Port 80h POST Codes ....................................................................... 64
4.1
BIOS Front-panel Power LED Codes
The front-panel power LED blinks off and on to display messages. For example, the
power LED is on when the system is powered on, and blinks off for 0.5 second when
processor initialization is complete. In addition, whenever a recoverable error occurs
during POST, the BIOS causes the front-panel power LED to blink an error message
describing the problem (see Table 30).
Table 30. Front-panel Power LED Blink Codes
4.2
Type
Pattern
Processor initialization complete
On when system powers up, then off for 0.5 second.
POST complete
On when system powers up, then off for 0.5 second.
BIOS update in progress
Off when update begins, then on for 0.5 second, then off for 0.5
second; pattern repeats until BIOS update is complete.
Video error
On-off (0.5 second each) two times, then 3.0 second pause (off)
between on-off blink pattern; repeat entire pattern (two on-off
blinks and pause) until system is powered off.
Memory error
On-off (0.5 second each) three times, then 3.0 second pause (off)
between on-off blink pattern; repeat entire pattern (three on-off
blinks and 3-second pause) until system is powered off.
Thermal warning
On-off (0.5 second each) four times, then 3.0 second pause (off)
between on-off blink pattern; repeat entire pattern (four on-off
blinks and 3-second pause) until 16th on blink, then end.
BIOS Error Messages
Table 31 lists the error messages and provides a brief description of each.
Table 31. BIOS Error Messages
Error Message
Explanation
CMOS Battery Low
The battery may be losing power. Replace the battery soon.
CMOS Checksum Bad
The CMOS checksum is incorrect. CMOS memory may have been
corrupted. Run Setup to reset values.
Memory Size Decreased
Memory size has decreased since the last boot. If no memory was
removed then memory may be bad.
No Boot Device Available
System did not find a device to boot.
63
Intel Desktop Board D945GCPE Technical Product Specification
4.3
Port 80h POST Codes
During the POST, the BIOS generates diagnostic progress codes (POST-codes) to I/O
port 80h. If the POST fails, execution stops and the last POST code generated is left
at port 80h. This code is useful for determining the point where an error occurred.
Displaying the POST-codes requires a PCI bus add-in card, often called a POST card.
The POST card can decode the port and display the contents on a medium such as a
seven-segment display.
NOTE
The POST card must be installed in PCI bus connector 1.
The following tables provide information about the POST codes generated by the
BIOS:
•
•
•
Table 32 lists the Port 80h POST code ranges
Table 33 lists the Port 80h POST codes themselves
Table 34 lists the Port 80h POST sequence
NOTE
In the tables listed above, all POST codes and range values are listed in hexadecimal.
Table 32. Port 80h POST Code Ranges
Range
Category/Subsystem
00 – 0F
Debug codes: Can be used by any PEIM/driver for debug.
10 – 1F
Host Processors: 1F is an unrecoverable CPU error.
20 – 2F
Memory/Chipset: 2F is no memory detected or no useful memory detected.
30 – 3F
Recovery: 3F indicated recovery failure.
40 – 4F
Reserved for future use.
50 – 5F
I/O Busses: PCI, USB, ATA, etc. 5F is an unrecoverable error. Start with PCI.
60 – 6F
Reserved for future use (for new busses).
70 – 7F
Output Devices: All output consoles. 7F is an unrecoverable error.
80 – 8F
Reserved for future use (new output console codes).
90 – 9F
Input devices: Keyboard/Mouse. 9F is an unrecoverable error.
A0 – AF
Reserved for future use (new input console codes).
B0 – BF
Boot Devices: Includes fixed media and removable media. BF is an unrecoverable error.
C0 – CF
Reserved for future use.
D0 – DF
Boot device selection.
E0 – FF
E0 – EE: Miscellaneous codes. See Table 33.
EF: boot/S3 resume failure.
F0 – FF: FF processor exception.
64
Error Messages and Beep Codes
Table 33. Port 80h POST Codes
POST Code
Description of POST Operation
Host Processor
10
Power-on initialization of the host processor (Boot Strap Processor)
11
Host processor Cache initialization (including APs)
12
Starting Application processor initialization
13
SMM initialization
21
Initializing a chipset component
Chipset
Memory
22
Reading SPD from memory DIMMs
23
Detecting presence of memory DIMMs
24
Programming timing parameters in the memory controller and the DIMMs
25
Configuring memory
26
Optimizing memory settings
27
Initializing memory, such as ECC init
28
Testing memory
50
Enumerating PCI busses
51
Allocating resources to PCI bus
PCI Bus
52
Hot Plug PCI controller initialization
53 – 57
Reserved for PCI Bus
USB
58
Resetting USB bus
59
Reserved for USB
ATA/ATAPI/SATA
5A
Resetting PATA/SATA bus and all devices
5B
Reserved for ATA
SMBus
5C
Resetting SMBUS
5D
Reserved for SMBUS
Local Console
70
Resetting the VGA controller
71
Disabling the VGA controller
72
Enabling the VGA controller
Remote Console
78
Resetting the console controller
79
Disabling the console controller
7A
Enabling the console controller
continued
65
Intel Desktop Board D945GCPE Technical Product Specification
Table 33. Port 80h POST Codes (continued)
POST Code
Description of POST Operation
Keyboard (PS/2 or USB)
90
Resetting keyboard
91
Disabling keyboard
92
Detecting presence of keyboard
93
Enabling keyboard
94
Clearing keyboard input buffer
95
Instructing keyboard controller to run Self Test (PS2 only)
Mouse (PS/2 or USB)
98
Resetting mouse
99
Disabling mouse
9A
Detecting presence of mouse
9B
Enabling mouse
Fixed Media
B0
Resetting fixed media
B1
Disabling fixed media
B2
Detecting presence of a fixed media (IDE hard drive detection etc.)
B3
Enabling/configuring a fixed media
Removable media
B8
Resetting removable media
B9
Disabling removable media
BA
Detecting presence of a removable media (IDE, CD-ROM detection, etc.)
BC
Enabling/configuring a removable media
Dy
Trying boot selection y (y=0 to 15)
BDS
PEI Core
E0
Started dispatching PEIMs (emitted on first report of EFI_SW_PC_INIT_BEGIN
EFI_SW_PEI_PC_HANDOFF_TO_NEXT)
E2
Permanent memory found
E1, E3
Reserved for PEI/PEIMs
DXE Core
E4
Entered DXE phase
E5
Started dispatching drivers
E6
Started connecting drivers
continued
66
Error Messages and Beep Codes
Table 33. Port 80h POST Codes (continued)
POST Code
Description of POST Operation
DXE Drivers
E7
Waiting for user input
E8
Checking password
E9
Entering BIOS setup
EB
Calling Legacy Option ROMs
F4
Entering Sleep state
F5
Exiting Sleep state
F8
EFI boot service ExitBootServices ( ) has been called
F9
EFI runtime service SetVirtualAddressMap ( ) has been called
FA
EFI runtime service ResetSystem ( ) has been called
30
Crisis Recovery has initiated per User request
31
Crisis Recovery has initiated by software (corrupt flash)
34
Loading recovery capsule
35
Handing off control to the recovery capsule
3F
Unable to recover
Runtime Phase/EFI OS Boot
PEIMs/Recovery
67
Intel Desktop Board D945GCPE Technical Product Specification
Table 34. Typical Port 80h POST Sequence
68
POST Code
Description
21
Initializing a chipset component
22
Reading SPD from memory DIMMs
23
Detecting presence of memory DIMMs
25
Configuring memory
28
Testing memory
34
Loading recovery capsule
E4
Entered DXE phase
12
Starting Application processor initialization
13
SMM initialization
50
Enumerating PCI busses
51
Allocating resourced to PCI bus
92
Detecting the presence of the keyboard
90
Resetting keyboard
94
Clearing keyboard input buffer
95
Keyboard Self Test
EB
Calling Video BIOS
58
Resetting USB bus
5A
Resetting PATA/SATA bus and all devices
92
Detecting the presence of the keyboard
90
Resetting keyboard
94
Clearing keyboard input buffer
5A
Resetting PATA/SATA bus and all devices
28
Testing memory
90
Resetting keyboard
94
Clearing keyboard input buffer
E7
Waiting for user input
01
INT 19
00
Ready to boot
5
Regulatory Compliance and Battery
Disposal Information
What This Chapter Contains
5.1 Regulatory Compliance..................................................................... 69
5.2 Battery Disposal Information............................................................. 77
5.1
Regulatory Compliance
This section contains the following regulatory compliance information for Desktop
Board D945GCPE:
•
•
•
•
•
5.1.1
Safety standards
European Union Declaration of Conformity statement
Product Ecology statements
Electromagnetic Compatibility (EMC) standards
Product certification markings
Safety Standards
Desktop Board D945GCPE complies with the safety standards stated in Table 35 when
correctly installed in a compatible host system.
Table 35. Safety Standards
Standard
Title
UL 60950-1, First Edition
Information Technology Equipment – Safety - Part 1: General
Requirements (USA and Canada)
EN 60950-1:2006, Second
Edition
Information Technology Equipment – Safety - Part 1: General
Requirements (European Union)
IEC 60950-1:2005, Second
Edition
Information Technology Equipment – Safety - Part 1: General
Requirements (International)
69
Intel Desktop Board D945GCPE Technical Product Specification
5.1.2
European Union Declaration of Conformity
Statement
We, Intel Corporation, declare under our sole responsibility that the product Intel®
Desktop Board D945GCPE is in conformity with all applicable essential requirements
necessary for CE marking, following the provisions of the European Council Directive
2004/108/EC (EMC Directive) and 2006/95/EC (Low Voltage Directive).
The product is properly CE marked demonstrating this conformity and is for
distribution within all member states of the EU with no restrictions.
This product follows the provisions of the European Directives 2004/108/EC and
2006/95/EC.
Čeština Tento výrobek odpovídá požadavkům evropských směrnic 2004/108/EC a
2006/95/EC.
Dansk Dette produkt er i overensstemmelse med det europæiske direktiv
2004/108/EC & 2006/95/EC.
Dutch Dit product is in navolging van de bepalingen van Europees Directief
2004/108/EC & 2006/95/EC.
Eesti Antud toode vastab Euroopa direktiivides 2004/108/EC ja 2006/95/EC
kehtestatud nõuetele.
Suomi Tämä tuote noudattaa EU-direktiivin 2004/108/EC & 2006/95/EC määräyksiä.
Français Ce produit est conforme aux exigences de la Directive Européenne
2004/108/EC & 2006/95/EC.
Deutsch Dieses Produkt entspricht den Bestimmungen der Europäischen Richtlinie
2004/108/EC & 2006/95/EC.
Ελληνικά Το παρόν προϊόν ακολουθεί τις διατάξεις των Ευρωπαϊκών Οδηγιών
2004/108/EC και 2006/95/EC.
Magyar E termék megfelel a 2004/108/EC és 2006/95/EC Európai Irányelv
előírásainak.
Icelandic Þessi vara stenst reglugerð Evrópska Efnahags Bandalagsins númer
2004/108/EC & 2006/95/EC.
Italiano Questo prodotto è conforme alla Direttiva Europea 2004/108/EC &
2006/95/EC.
Latviešu Šis produkts atbilst Eiropas Direktīvu 2004/108/EC un 2006/95/EC
noteikumiem.
Lietuvių Šis produktas atitinka Europos direktyvų 2004/108/EC ir 2006/95/EC
nuostatas.
Malti Dan il-prodott hu konformi mal-provvedimenti tad-Direttivi Ewropej
2004/108/EC u 2006/95/EC.
Norsk Dette produktet er i henhold til bestemmelsene i det europeiske direktivet
2004/108/EC & 2006/95/EC.
Polski Niniejszy produkt jest zgodny z postanowieniami Dyrektyw Unii Europejskiej
2004/108/EC i 73/23/EWG.
Portuguese Este produto cumpre com as normas da Diretiva Européia 2004/108/EC
& 2006/95/EC.
70
Regulatory Compliance and Battery Disposal Information
Español Este producto cumple con las normas del Directivo Europeo 2004/108/EC &
2006/95/EC.
Slovensky Tento produkt je v súlade s ustanoveniami európskych direktív
2004/108/EC a 2006/95/EC.
Slovenščina Izdelek je skladen z določbami evropskih direktiv 2004/108/EC in
2006/95/EC.
Svenska Denna produkt har tillverkats i enlighet med EG-direktiv 2004/108/EC &
2006/95/EC.
Türkçe Bu ürün, Avrupa Birliği’nin 2004/108/EC ve 2006/95/EC yönergelerine uyar.
5.1.3
Product Ecology Statements
The following information is provided to address worldwide product ecology concerns
and regulations.
5.1.3.1
Disposal Considerations
This product contains the following materials that may be regulated upon disposal:
lead solder on the printed wiring board assembly.
5.1.3.2
Recycling Considerations
As part of its commitment to environmental responsibility, Intel has implemented the
Intel Product Recycling Program to allow retail consumers of Intel’s branded products
to return used products to selected locations for proper recycling.
Please consult the http://www.intel.com/intel/other/ehs/product_ecology for the
details of this program, including the scope of covered products, available locations,
shipping instructions, terms and conditions, etc.
中文
作为其对环境责任之承诺的部分，英特尔已实施 Intel Product Recycling Program
（英特尔产品回收计划），以允许英特尔品牌产品的零售消费者将使用过的产品退还至指定地点作
恰当的重复使用处理。
请参考http://www.intel.com/intel/other/ehs/product_ecology
了解此计划的详情，包括涉及产品之范围、回收地点、运送指导、条款和条件等。
71
Intel Desktop Board D945GCPE Technical Product Specification
Deutsch
Als Teil von Intels Engagement für den Umweltschutz hat das Unternehmen das Intel
Produkt-Recyclingprogramm implementiert, das Einzelhandelskunden von Intel
Markenprodukten ermöglicht, gebrauchte Produkte an ausgewählte Standorte für
ordnungsgemäßes Recycling zurückzugeben.
Details zu diesem Programm, einschließlich der darin eingeschlossenen Produkte,
verfügbaren Standorte, Versandanweisungen, Bedingungen usw., finden Sie auf der
http://www.intel.com/intel/other/ehs/product_ecology
Español
Como parte de su compromiso de responsabilidad medioambiental, Intel ha
implantado el programa de reciclaje de productos Intel, que permite que los
consumidores al detalle de los productos Intel devuelvan los productos usados en los
lugares seleccionados para su correspondiente reciclado.
Consulte la http://www.intel.com/intel/other/ehs/product_ecology para ver los detalles del
programa, que incluye los productos que abarca, los lugares disponibles, instrucciones
de envío, términos y condiciones, etc.
Français
Dans le cadre de son engagement pour la protection de l'environnement, Intel a mis
en œuvre le programme Intel Product Recycling Program (Programme de recyclage
des produits Intel) pour permettre aux consommateurs de produits Intel de recycler
les produits usés en les retournant à des adresses spécifiées.
Visitez la page Web http://www.intel.com/intel/other/ehs/product_ecology pour en savoir
plus sur ce programme, à savoir les produits concernés, les adresses disponibles, les
instructions d'expédition, les conditions générales, etc.
日本語
インテルでは、環境保護活動の一環として、使い終えたインテル
ブランド製品を指定の場所へ返送していただき、リサイクルを適切に行えるよう、インテル製品リサイクル
プログラムを発足させました。
対象製品、返送先、返送方法、ご利用規約など、このプログラムの詳細情報は、http://www.intel.com/intel
/other/ehs/product_ecology （英語）をご覧ください。
Malay
Sebagai sebahagian daripada komitmennya terhadap tanggungjawab persekitaran,
Intel telah melaksanakan Program Kitar Semula Produk untuk membenarkan
pengguna-pengguna runcit produk jenama Intel memulangkan produk terguna ke
lokasi-lokasi terpilih untuk dikitarkan semula dengan betul.
Sila rujuk http://www.intel.com/intel/other/ehs/product_ecology untuk mendapatkan butirbutir program ini, termasuklah skop produk yang dirangkumi, lokasi-lokasi tersedia,
arahan penghantaran, terma & syarat, dsb.
72
Regulatory Compliance and Battery Disposal Information
Portuguese
Como parte deste compromisso com o respeito ao ambiente, a Intel implementou o
Programa de Reciclagem de Produtos para que os consumidores finais possam enviar
produtos Intel usados para locais selecionados, onde esses produtos são reciclados de
maneira adequada.
Consulte o site http://www.intel.com/intel/other/ehs/product_ecology (em Inglês) para
obter os detalhes sobre este programa, inclusive o escopo dos produtos cobertos, os
locais disponíveis, as instruções de envio, os termos e condições, etc.
Russian
В качестве части своих обязательств к окружающей среде, в Intel создана
программа утилизации продукции Intel (Product Recycling Program) для
предоставления конечным пользователям марок продукции Intel возможности
возврата используемой продукции в специализированные пункты для должной
утилизации.
Пожалуйста, обратитесь на веб-сайт
http://www.intel.com/intel/other/ehs/product_ecology за информацией об этой
программе, принимаемых продуктах, местах приема, инструкциях об отправке,
положениях и условиях и т.д.
Türkçe
Intel, çevre sorumluluğuna bağımlılığının bir parçası olarak, perakende tüketicilerin
Intel markalı kullanılmış ürünlerini belirlenmiş merkezlere iade edip uygun şekilde geri
dönüştürmesini amaçlayan Intel Ürünleri Geri Dönüşüm Programı’nı uygulamaya
koymuştur.
Bu programın ürün kapsamı, ürün iade merkezleri, nakliye talimatları, kayıtlar ve
şartlar v.s dahil bütün ayrıntılarını ögrenmek için lütfen
http://www.intel.com/intel/other/ehs/product_ecology Web sayfasına gidin.
73
Intel Desktop Board D945GCPE Technical Product Specification
5.1.3.3
Lead Free Desktop Board
This Desktop Board is a European Union Restriction of Hazardous Substances (EU
RoHS Directive 2002/95/EC) compliant product. EU RoHS restricts the use of six
materials. One of the six restricted materials is lead.
This Desktop Board is lead free although certain discrete components used on the
board contain a small amount of lead which is necessary for component performance
and/or reliability. This Desktop Board is referred to as “Lead-free second level
interconnect.” The board substrate and the solder connections from the board to the
components (second-level connections) are all lead free.
China bans the same substances and has the same limits as EU RoHS; however it
requires different product marking and controlled substance information. The required
mark shows the Environmental Friendly Usage Period (EFUP). The EFUP is defined as
the number of years for which controlled listed substances will not leak or chemically
deteriorate while in the product.
Table 36 shows the various forms of the “Lead-Free 2nd Level Interconnect” mark as it
appears on the board and accompanying collateral.
Table 36. Lead-Free Board Markings
Description
Mark
nd
Lead-Free 2 Level
Interconnect: This symbol is
used to identify electrical and
electronic assemblies and
components in which the lead
(Pb) concentration level in the
desktop board substrate and the
solder connections from the board
to the components (second-level
interconnect) is not greater than
0.1% by weight (1000 ppm).
or
or
74
Regulatory Compliance and Battery Disposal Information
5.1.4
EMC Regulations
Desktop Board D945GCPE complies with the EMC regulations stated in Table 37 when
correctly installed in a compatible host system.
Table 37. EMC Regulations
Regulation
Title
FCC 47 CFR Part 15,
Subpart B
Title 47 of the Code of Federal Regulations, Part 15, Subpart B, Radio
Frequency Devices. (USA)
ICES-003 Issue 4
(Class B)
Interference-Causing Equipment Standard, Digital Apparatus. (Canada)
EN55022: 2006
(Class B)
Limits and methods of measurement of Radio Interference Characteristics
of Information Technology Equipment. (European Union)
EN55024:1998
Information Technology Equipment – Immunity Characteristics Limits and
methods of measurement. (European Union)
EN55022:2006
(Class B)
Australian Communications Authority, Standard for Electromagnetic
Compatibility. (Australia and New Zealand)
CISPR 222005
+A1:2005 +A2:2006
(Class B)
Limits and methods of measurement of Radio Disturbance Characteristics of
Information Technology Equipment. (International)
CISPR 24: 1997
+A1:2001 +A2:2002
Information Technology Equipment – Immunity Characteristics – Limits and
Methods of Measurement. (International)
VCCI V-3/2007.04,
V-4/2007.04, Class B
Voluntary Control for Interference by Information Technology Equipment.
(Japan)
Japanese Kanji statement translation: this is a Class B product based on the standard
of the Voluntary Control Council for Interference from Information Technology
Equipment (VCCI). If this is used near a radio or television receiver in a domestic
environment, it may cause radio interference. Install and use the equipment
according to the instruction manual.
75
Intel Desktop Board D945GCPE Technical Product Specification
Korean Class B statement translation: this is household equipment that is certified to
comply with EMC requirements. You may use this equipment in residential
environments and other non-residential environments.
5.1.5
Product Certification Markings (Board Level)
Desktop Board D945GCPE has the product certification markings shown in Table 38:
Table 38. Product Certification Markings
Description
Mark
UL joint US/Canada Recognized Component mark. Includes adjacent UL file
number for Intel desktop boards: E210882.
FCC Declaration of Conformity logo mark for Class B equipment. Includes
Intel name and D945GCPE model designation.
CE mark. Declaring compliance to European Union (EU) EMC directive and
Low Voltage directive.
Australian Communications Authority (ACA) C-tick mark. Includes adjacent
Intel supplier code number, N-232.
Japan VCCI (Voluntary Control Council for Interference) mark.
S. Korea MIC (Ministry of Information and Communication) mark. Includes
adjacent MIC certification number: CPU-D945GCPE (B)
Taiwan BSMI (Bureau of Standards, Metrology and Inspections) mark.
Includes adjacent Intel company number, D33025.
Printed wiring board manufacturer’s recognition mark. Consists of a unique UL
recognized manufacturer’s logo, along with a flammability rating (solder side).
China RoHS/Environmentally Friendly Use Period Logo: This is an
example of the symbol used on Intel Desktop Boards and associated
collateral. The color of the mark may vary depending upon the application.
The Environmental Friendly Usage Period (EFUP) for Intel Desktop Boards has
been determined to be 10 years.
76
V-0
Regulatory Compliance and Battery Disposal Information
5.2
Battery Disposal Information
CAUTION
Risk of explosion if the battery is replaced with an incorrect type. Batteries should be
recycled where possible. Disposal of used batteries must be in accordance with local
environmental regulations.
PRÉCAUTION
Risque d'explosion si la pile usagée est remplacée par une pile de type incorrect. Les
piles usagées doivent être recyclées dans la mesure du possible. La mise au rebut des
piles usagées doit respecter les réglementations locales en vigueur en matière de
protection de l'environnement.
FORHOLDSREGEL
Eksplosionsfare, hvis batteriet erstattes med et batteri af en forkert type. Batterier
bør om muligt genbruges. Bortskaffelse af brugte batterier bør foregå i
overensstemmelse med gældende miljølovgivning.
OBS!
Det kan oppstå eksplosjonsfare hvis batteriet skiftes ut med feil type. Brukte batterier
bør kastes i henhold til gjeldende miljølovgivning.
VIKTIGT!
Risk för explosion om batteriet ersätts med felaktig batterityp. Batterier ska kasseras
enligt de lokala miljövårdsbestämmelserna.
VARO
Räjähdysvaara, jos pariston tyyppi on väärä. Paristot on kierrätettävä, jos se on
mahdollista. Käytetyt paristot on hävitettävä paikallisten ympäristömääräysten
mukaisesti.
VORSICHT
Bei falschem Einsetzen einer neuen Batterie besteht Explosionsgefahr. Die Batterie
darf nur durch denselben oder einen entsprechenden, vom Hersteller empfohlenen
Batterietyp ersetzt werden. Entsorgen Sie verbrauchte Batterien den Anweisungen
des Herstellers entsprechend.
AVVERTIMENTO
Esiste il pericolo di un esplosione se la pila non viene sostituita in modo corretto.
Utilizzare solo pile uguali o di tipo equivalente a quelle consigliate dal produttore. Per
disfarsi delle pile usate, seguire le istruzioni del produttore.
77
Intel Desktop Board D945GCPE Technical Product Specification
PRECAUCIÓN
Existe peligro de explosión si la pila no se cambia de forma adecuada. Utilice
solamente pilas iguales o del mismo tipo que las recomendadas por el fabricante del
equipo. Para deshacerse de las pilas usadas, siga igualmente las instrucciones del
fabricante.
WAARSCHUWING
Er bestaat ontploffingsgevaar als de batterij wordt vervangen door een onjuist type
batterij. Batterijen moeten zoveel mogelijk worden gerecycled. Houd u bij het
weggooien van gebruikte batterijen aan de plaatselijke milieuwetgeving.
ATENÇÃO
Haverá risco de explosão se a bateria for substituída por um tipo de bateria incorreto.
As baterias devem ser recicladas nos locais apropriados. A eliminação de baterias
usadas deve ser feita de acordo com as regulamentações ambientais da região.
AŚCIAROŽZNAŚĆ
Існуе рызыка выбуху, калі заменены акумулятар неправільнага тыпу.
Акумулятары павінны, па магчымасці, перепрацоўвацца. Пазбаўляцца ад старых
акумулятараў патрэбна згодна з мясцовым заканадаўствам па экалогіі.
UPOZORNÌNÍ
V případě výměny baterie za nesprávný druh může dojít k výbuchu. Je-li to možné,
baterie by měly být recyklovány. Baterie je třeba zlikvidovat v souladu s místními
předpisy o životním prostředí.
Προσοχή
Υπάρχει κίνδυνος για έκρηξη σε περίπτωση που η μπαταρία αντικατασταθεί από μία
λανθασμένου τύπου. Οι μπαταρίες θα πρέπει να ανακυκλώνονται όταν κάτι τέτοιο είναι
δυνατό. Η απόρριψη των χρησιμοποιημένων μπαταριών πρέπει να γίνεται σύμφωνα με
τους κατά τόπο περιβαλλοντικούς κανονισμούς.
VIGYÁZAT
Ha a telepet nem a megfelelő típusú telepre cseréli, az felrobbanhat. A telepeket
lehetőség szerint újra kell hasznosítani. A használt telepeket a helyi környezetvédelmi
előírásoknak megfelelően kell kiselejtezni.
78
Regulatory Compliance and Battery Disposal Information
AWAS
Risiko letupan wujud jika bateri digantikan dengan jenis yang tidak betul. Bateri
sepatutnya dikitar semula jika boleh. Pelupusan bateri terpakai mestilah mematuhi
peraturan alam sekitar tempatan.
OSTRZEŻENIE
Istnieje niebezpieczeństwo wybuchu w przypadku zastosowania niewłaściwego typu
baterii. Zużyte baterie należy w miarę możliwości utylizować zgodnie z odpowiednimi
przepisami ochrony środowiska.
PRECAUŢIE
Risc de explozie, dacă bateria este înlocuită cu un tip de baterie necorespunzător.
Bateriile trebuie reciclate, dacă este posibil. Depozitarea bateriilor uzate trebuie să
respecte reglementările locale privind protecţia mediului.
ВНИМАНИЕ
При использовании батареи несоответствующего типа существует риск ее взрыва.
Батареи должны быть утилизированы по возможности. Утилизация батарей
должна проводится по правилам, соответствующим местным требованиям.
UPOZORNENIE
Ak batériu vymeníte za nesprávny typ, hrozí nebezpečenstvo jej výbuchu.
Batérie by sa mali podľa možnosti vždy recyklovať. Likvidácia použitých batérií sa musí
vykonávať v súlade s miestnymi predpismi na ochranu životného prostredia.
POZOR
Zamenjava baterije z baterijo drugačnega tipa lahko povzroči eksplozijo.
Če je mogoče, baterije reciklirajte. Rabljene baterije zavrzite v skladu z lokalnimi
okoljevarstvenimi predpisi.
.
UYARI
Yanlış türde pil takıldığında patlama riski vardır. Piller mümkün olduğunda geri
dönüştürülmelidir. Kullanılmış piller, yerel çevre yasalarına uygun olarak atılmalıdır.
OСТОРОГА
Використовуйте батареї правильного типу, інакше існуватиме ризик вибуху.
Якщо можливо, використані батареї слід утилізувати. Утилізація використаних
батарей має бути виконана згідно місцевих норм, що регулюють охорону довкілля.
79
Intel Desktop Board D945GCPE Technical Product Specification
80