LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only SURFACE MOUNT LED TAPE AND REEL Pb Lead-Free Parts LHYS9553 DATA SHEET DOC. NO REV. DATE : QW0905- LHYS9553 : A : 27 - Dec. - 2005 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 1/6 PART NO. : LHYS9553 Package Dimensions 3.5 3.2 1.85 2.8 2.2 1.85 0.95 0.9 + 0.9 - Note : 1.All dimension are in millimeter tolerance is ±0.25mm unless otherwise noted. 2.Specifications are subject to change without notice. Directivity Radiation 0° -30° 30° -60° 100% 75% 50% 60° 25% 0 25% 50% 75% 100% LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 2/6 PART NO. : LHYS9553 Absolute Maximum Ratings at Ta=25 ℃ Ratings Symbol Parameter UNIT HYS Forward Current IF 30 mA Peak Forward Current Duty 1/10@10KHz IFP 60 mA Power Dissipation PD 75 mW Ir 10 μA Electrostatic Discharge( * ) ESD 2000 V Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +100 ℃ Reverse Current @5V Typical Electrical & Optical Characteristics (Ta=25 ℃) COLOR PART NO MATERIAL Emitted LHYS9553 AlGaInP Yellow Dominant Spectral wave halfwidth length △λ nm λDnm Luminous intensity @20mA(mcd) Min. Max. Min. Lens Water Clear Forward voltage @20mA(V) 587 15 1.7 Note : 1.The forward voltage data did not including ±0.1V testing tolerance. 2. The luminous intensity data did not including ±15% testing tolerance. 2.6 80 Viewing angle 2θ 1/2 (deg) Typ. 200 120 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page3/6 PART NO: LHYS9553 Typical Electro-Optical Characteristics Curve HYS CHIP Fig.1 Forward current vs. Forward Voltage Fig.2 Relative Intensity vs. Forward Current 3.0 Relative Intensity Normalize @20mA Forward Current(mA) 1000 100 10 1.0 0.1 2.5 2.0 1.5 1.0 0.5 0.0 1.5 1.0 2.0 2.5 3.0 1.0 10 Fig.3 Forward Voltage vs. Temperature Fig.4 Relative Intensity vs. Temperature 1.2 3.0 Relative Intensity@20mA Normalize @25℃ Forward Voltage@20mA Normalize @25℃ 1000 Forward Current(mA) Forward Voltage(V) 1.1 1.0 0.9 0.8 -40 -20 0 20 40 60 80 Fig.5 Relative Intensity vs. Wavelength 1.0 0.5 0.0 500 550 600 Wavelength (nm) 100 2.5 2.0 1.5 1.0 0.5 0.0 -40 -20 0 20 40 60 80 Ambient Temperature( ℃) Ambient Temperature( ℃) Relative Intensity@20mA 100 650 100 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 4/6 PART NO. : LHYS9553 Recommended Soldering Conditions 1. Hand Solder Basic spec is ≦ 280℃ 3 sec one time only. 2. Wave Solder Soldering heat Max. 260 ℃ 245± 5℃ within 5 sec Preheat 120 ~ 150℃ 120 ~ 180 sec 3-1. LEAD Reflow Solder Temp. (℃) 240 Rising +5℃/sec Cooling -5℃ /sec Preheat 150 120 60 ~ 120 sec Time 5sec 3-2 PB-Free Reflow Solder 1~5° C/sec Preheat 180~200 ° C 1~5° C/sec 260°C MaX. 10sec.Max Above 220 ° C 60 sec.Max. 120 sec.Max. Reflow Soldering should not be done more than two times. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. : LHYS9553 Page 5/6 Precautions For Use: Storage time: 1.The operation of Temperatures and RH are : 5 ℃~35℃,RH<60%. 2.Once the package is opened, the products should be used within a week. Otherwise, they should be kept in a damp proof box with descanting agent. Considering the tape life, we suggest our customers to use our products within a year(from production date). 3.If opened more than one week in an atmosphere 5 ℃ ~ 35℃,RH<60%, they should be treated at 60 ℃± 5 ℃fo r 15hrs. Drive Method: LED is a current operated device, and therefore, requirer some kind of current limiting incorporated into the driver circuit. This current limiting typically takes the form of a current limiting resistor placed in series with the LED. Consider worst case voltage variations than could occur across the current limiting resistor. The forwrd current should not be allowed to change by more than 40 % of its desired value. Circuit model A Circuit model B LED LED (A) Recommended circuit. (B) The difference of brightness between LED could be found due to the VF-IF characteristics of LED. Cleaning: Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED. ESD(Electrostatic Discharge): Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 6/6 PART NO. : LHYS9553 Reliability Test: Classification Test Item Test Condition Reference Standard Operating Life Test 1.Ta=Under Room Temperature As Per Data Sheet Maximum Rating. 2.If=20mA 3.t=1000 hrs (-24hrs, +72hrs) MIL-STD-750D: 1026 MIL-STD-883D: 1005 JIS C 7021: B-1 High Temperature Storage Test 1.Ta=105 ℃±5 ℃ 2.t=1000 hrs (-24hrs, +72hrs) MIL-STD-883D:1008 JIS C 7021: B-10 Low Temperature Storage Test 1.Ta=-40 ℃±5℃ 2.t=1000 hrs (-24hrs, +72hrs) JIS C 7021: B-12 High Temperature High Humidity Storage Test 1.Ta=65 ℃±5℃ 2.RH=90 %~95 % 3.t=1000hrs ±2hrs Endurance Test Thermal Shock Test Solderability Test Temperature Cycling 1.Ta=105 ℃±5 ℃&-40 ℃±5℃ (10min) (10min) 2.total 10 cycles 1.T.Sol=235 ℃±5℃ 2.Immersion time 2 ±0.5sec 3.Coverage ≧95% of the dipped surface MIL-STD-202F: 107D MIL-STD-750D: 1051 MIL-STD-883D: 1011 MIL-STD-202F: 208D MIL-STD-750D: 2026 MIL-STD-883D: 2003 IEC 68 Part 2-20 JIS C 7021: A-2 1.105 ℃ ~ 25 ℃ ~ -55 ℃ ~ 25 ℃ 30mins 5mins 30mins 5mins 2.10 Cyeles MIL-STD-202F: 107D MIL-STD-750D: 1051 MIL-STD-883D: 1010 JIS C 7021: A-4 Ramp-up rate(183 ℃ to Peak) +3 ℃ second max Temp. maintain at 125( ±25) ℃ 120 seconds max Temp. maintain above 183 ℃ 60-150 seconds Peak temperature range 235 ℃+5/-0 ℃ Time within 5 ℃ of actual Peak Temperature(tp) 10-30 seconds Ramp-down rate +6 ℃/second max MIL-STD-750D:2031.2 J-STD-020 Environmental Test IR Reflow MIL-STD-202F:103B JIS C 7021: B-11