LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only DUAL COLOR LED LAMPS Pb Lead-Free Parts LSBKS9UG2093 DATA SHEET DOC. NO : QW0905-LSBKS9UG2093 REV. : B DATE : 27 - Mar. - 2008 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LSBKS9UG2093 Page 1/6 Package Dimensions 3.0 4.2 4.0 5.2 6.7±0.5 1.5 MAX 9UG SBKS 0.5 TYP 18.0MIN 1 2 1 2 3 3 1.ANODE GREEN 2.COMMON CATHODE 3.ANODE BIUE 2.0MIN 2.0MIN 2.54TYP 2.54TYP Note : 1.All dimension are in millimeter tolerance is ± 0.25mm unless otherwise noted. 2.Specifications are subject to change without notice. Directivity Radiation 0° -30° 30° -60° 100% 75% 50% -60° 25% 0 25% 50% 75% 100% LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LSBKS9UG2093 Page 2/6 Absolute Maximum Ratings at Ta=25 ℃ Ratings Symbol Parameter UNIT SBKS 9UG Forward Current IF 30 30 mA Peak Forward Current Duty 1/10@10KHz IFP 100 60 mA Power Dissipation PD 120 75 mW Ir 50 10 μA Electrostatic Discharge( * ) ESD 500 2000 V Operating Temperature Topr -20 ~ +85 ℃ Storage Temperature Tstg -30 ~ +100 ℃ Reverse Current @5V Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic * glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded. Typical Electrical & Optical Characteristics (Ta=25 ℃) COLOR PART NO MATERIAL Emitted Forward Spectral voltage halfwidth @20mA(V) △λnm Lens InGaN/SiC Blue LSBKS9UG2093 Dominant wave length λDnm Luminous intensity @20mA(mcd) Viewing angle 2θ 1/2 (deg) Min. Typ. Max. Min. Typ. 475 26 ---- 3.5 4.2 550 1100 30 574 20 1.7 ---- 2.6 160 30 Water Clear AlGaInP Green Note : 1.The forward voltage data did not including ±0.1V testing tolerance. 2. The luminous intensity data did not including ± 15% testing tolerance. 350 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LSBKS9UG2093 Page 3/6 Typical Electro-Optical Characteristics Curve SBK-S CHIP Fig.2 Relative Intensity vs. Forward Current 30 1.5 Relative Intensity Normalize @20mA Forward Current(mA) Fig.1 Forward current vs. Forward Voltage 25 20 15 10 5 0 1 2 3 4 1.25 1.0 0.75 0.5 0.25 0 5 0 5 Relative Intensity@20mA Forward Current@20mA 40 30 20 10 0 50 75 Ambient Temperature( ℃) 20 25 30 Fig.4 Relative Intensity vs. Wavelength Fig.3 Forward Current vs. Temperature 25 15 Forward Current(mA) Forward Voltage(V) 0 10 100 1.0 0.5 0 380 430 480 530 580 Wavelength (nm) 630 680 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LSBKS9UG2093 Page 4/6 Typical Electro-Optical Characteristics Curve 9UG CHIP Fig.1 Forward current vs. Forward Voltage Fig.2 Relative Intensity vs. Forward Current 3.0 Relative Intensity Normalize @20mA Forward Current(mA) 1000 100 10 1.0 0.1 2.5 2.0 1.5 1.0 0.5 0 1.0 2.0 3.0 4.0 5.0 1.0 10 Fig.4 Relative Intensity vs. Temperature 1.2 Relative Intensity @20mA Normalize @25℃ Forward Voltage@20mA Normaliz @25℃ Fig.3 Forward Voltage vs. Temperature 1.1 1.0 0.9 0.8 -20 0 20 40 60 80 100 Relative Intensity @20mA Fig.5 Relative Intensity vs. Wavelength 1.0 0.5 0 550 600 Wavelength (nm) 3.0 2.5 2.0 1.5 1.0 0.5 0 -40 -20 0 20 40 60 80 Ambient Temperature( ℃) Ambient Temperature( ℃) 500 1000 Forward Current(mA) Forward Voltage(V) -40 100 650 100 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LSBKS9UG2093 Page 5/6 Soldering Condition(Pb-Free) 1.Iron: Soldering Iron:30W Max Temperature 350°C Max Soldering Time:3 Seconds Max(One time only) Distance:2mm Min(From solder joint to body) 2.Wave Soldering Profile Dip Soldering Preheat: 120° C Max Preheat time: 60seconds Max Ramp-up 2°C/sec(max) Ramp-Down:-5°C/sec(max) Solder Bath:260° C Max Dipping Time:3 seconds Max Distance:2mm Min(From solder joint to body) Temp(° C) 260° C3sec Max 260° 5° /sec max 120° 25° 0° 0 2° /sec max Preheat 60 Seconds Max 50 100 Note: 1.Wave solder should not be made more than one time. 2.You can just only select one of the soldering conditions as above. 150 Time(sec) LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LSBKS9UG2093 Page 6/6 Reliability Test: Test Item Test Condition Description Reference Standard Operating Life Test 1.Under Room Temperature 2.If=20mA 3.t=1000 hrs (-24hrs, +72hrs) This test is conducted for the purpose of detemining the resistance of a part in electrical and themal stressed. MIL-STD-750: 1026 MIL-STD-883: 1005 JIS C 7021: B-1 High Temperature Storage Test 1.Ta=105 ℃±5 ℃ 2.t=1000 hrs (-24hrs, +72hrs) The purpose of this is the resistance of the device which is laid under condition of high temperature for hours. MIL-STD-883:1008 JIS C 7021: B-10 Low Temperature Storage Test 1.Ta=-40 ℃±5℃ 2.t=1000 hrs (-24hrs, +72hrs) The purpose of this is the resistance of the device which is laid under condition of low temperature for hours. High Temperature High Humidity Test 1.Ta=65 ℃±5℃ 2.RH=90 %~95 % 3.t=240hrs ±2hrs The purpose of this test is the resistance of the device under tropical for hours. 1.Ta=105 ℃±5℃&-40 ℃±5℃ (10min) (10min) 2.total 10 cycles The purpose of this is the resistance of the device to sudden extreme changes in high and low temperature. MIL-STD-202: 107D MIL-STD-750: 1051 MIL-STD-883: 1011 Solder Resistance Test 1.T.Sol=260 ℃±5℃ 2.Dwell time= 10 ±1sec. This test intended to determine the thermal characteristic resistance of the device to sudden exposures at extreme changes in temperature when soldering the lead wire. MIL-STD-202: 210A MIL-STD-750: 2031 JIS C 7021: A-1 Solderability Test 1.T.Sol=230 ℃±5℃ 2.Dwell time=5 ±1sec This test intended to see soldering well performed or not. MIL-STD-202: 208D MIL-STD-750: 2026 MIL-STD-883: 2003 JIS C 7021: A-2 Thermal Shock Test JIS C 7021: B-12 MIL-STD-202:103B JIS C 7021: B-11