LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only SURFACE MOUNT LED TAPE AND REEL Pb Lead-Free Parts LSIR9S53/TR1 DATA SHEET DOC. NO : QW0905-LSIR9S53/TR1 REV. : A DATE : 14 - Oct. - 2008 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 1/7 PART NO.LSIR9S53/TR1 Package Dimensions 3.0 1.3 1.4 2.0 2.7 1.3 0.7 0.7 Carrier Type Dimensions 4.0 2.0 4.0 1.5 0.25 1.75 3.5 8.0 ±0.3 5.3 3.44 Polarity 1.53 Note : The tolerances unless mentioned is ±0.2mm,Angle ± 0.5. Unit=mm. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 2/7 PART NO.LSIR9S53/TR1 Reel Dimensions 0.2 0.4 0.8 0.8 0.6 0.2 0.4 178± 1.5 0.6 2.0±0.5 6.0± 1.0 9.0±1.0 ψ13.5±1.0 12.0± 1.0 Part No. Description Quantity/Reel LSIR9S53/TR1 8.0mm tape,7"reel 2000 devices LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO.LSIR9S53/TR1 Page 3/7 Absolute Maximum Ratings at Ta=25 ℃ Ratings Symbol Parameter UNIT SIR Forward Current IF 50 mA Peak Forward Current Duty 1/10@10KHz IFP 1 mA Power Dissipation PD 100 mW Ir 5 μA Electrostatic Discharge( * ) ESD 2000 V Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +100 ℃ Reverse Current @5V Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic *glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded. Electrical Optical Characteristics (Aa=25℃) SYMBOL Min. Typ. Radiant Intensity Le 0.5 Aperture Radiant Incidence Ee 0.07 Peak Emission Wavelength PARAMETER Max. UNIT TEST CONDITION 0.8 mW/sr IF=20mA 0.11 mW/cm IF=20mA λpeak 880 nm IF=20mA △λ 50 nm IF=20mA Forward Voltage VF 1.4 1.7 V IF=20mA Reverse Current IR 100 μA VR=5V Spectral Line Half Width Viewing Angle 2θ1/2 2 120 Note : 1.The forward voltage data did not including ±0.1V testing tolerance. 2. The radiant intensity data did not including ±15% testing tolerance. deg LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO.LSIR9S53/TR1 Page4/7 Typical Electro-Optical Characteristics Curve SIR CHIP Fig.1 Forward Current vs. Rorward Voltage Relative Radiant Intensity Normalize @20mA Forward Current(mA) 1000 Fig.2 Relative Radiant Intensity vs. Wavelength 100 10 1 0.1 0.5 1.0 1.5 2.0 2.5 1.0 0.5 0.0 750 800 Fig.3 Relative Radiant Power vs. Forward DC Current 950 1000 1050 Fig.4 Relative Radiant Power vs. Forward Peak Current 10.0 Relative Radiant Power Normalize @100 mA 10.0 1.0 0.1 1 10 1.0 0.1 10 100 100 1000 IFPK (mA) IFDC (mA) Fig.5 Forward DC Voltage vs. Temperature Fig.6 Relative Radiant Power vs. Temperature 1.2 3.0 Relative Radiant Power Normalize @ 20mA,25 ℃ Forward DC Voltage @20 mA Normalize @ 25 ℃ 900 Wavelength(nm) Forward Voltage(V) Relative Radiant Power Normalize @20mA 850 1.1 1.0 0.9 0.8 -40 -20 0 20 40 60 Ambient Temperature [℃] 80 100 2.5 2.0 1.5 1.0 0.5 0.0 -40 -20 0 20 40 60 Ambient Temperature[ ℃] 80 100 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO.LSIR9S53/TR1 Page5/7 Recommended Soldering Conditions 1. Hand Solder Basic spec is ≦ 280℃ 3 sec one time only. 2. Wave Solder Soldering heat Max. 260℃ 245±5℃ within 5 sec Preheat 120 ~ 150℃ 120 ~ 180 sec 3. LEAD Reflow Solder Temp. (℃) 240 Rising +5℃/sec Cooling -5℃/sec Preheat 150 120 60 ~ 120 sec Time 5sec 4. PB-Free Reflow Solder 1~5° C/sec Preheat 180~200 °C 1~5° C/sec 260° C MaX. 10sec.Max Above 220 °C 60 sec.Max. 120 sec.Max. Note: 1.Wave solder and reflow soldering should not be made more than one time. 2.You can just only select one of the soldering conditions as above. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO.LSIR9S53/TR1 Page 6/7 Precautions For Use: Storage time: 1.The operation of Temperatures and RH are : 5℃~35℃,RH<60%. 2.Once the package is opened, the products should be used within a week. Otherwise, they should be kept in a damp proof box with descanting agent. Considering the tape life, we suggest our customers to use our products within a year(from production date). 3.If opened more than one week in an atmosphere 5 ℃ ~ 35℃,RH<60%, they should be treated at 60℃± 5 ℃fo r 15hrs. Drive Method: LED is a current operated device, and therefore, requirer some kind of current limiting incorporated into the driver circuit. This current limiting typically takes the form of a current limiting resistor placed in series with the LED. Consider worst case voltage variations than could occur across the current limiting resistor. The forwrd current should not be allowed to change by more than 40% of its desired value. Circuit model A Circuit model B LED LED (A) Recommended circuit. (B) The difference of brightness between LED could be found due to the VF-IF characteristics of LED. Cleaning: Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED. ESD(Electrostatic Discharge): Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO.LSIR9S53/TR1 Page 7/7 Reliability Test: Classification Test Item Test Condition Reference Standard Operating Life Test 1.Ta=Under Room Temperature As Per Data Sheet Maximum Rating. 2.If=20mA 3.t=1000 hrs (-24hrs, +72hrs) MIL-STD-750D: 1026 MIL-STD-883D: 1005 JIS C 7021: B-1 High Temperature Storage Test 1.Ta=105℃±5℃ 2.t=1000 hrs (-24hrs, +72hrs) MIL-STD-883D:1008 JIS C 7021: B-10 Low Temperature Storage Test 1.Ta=-40℃±5℃ 2.t=1000 hrs (-24hrs, +72hrs) JIS C 7021: B-12 High Temperature High Humidity Storage Test 1.IR-Reflow In-Board, 2 Times 2.Ta=65℃±5℃ 3.RH=90%~95% 4.t=1000hrs±2hrs MIL-STD-202F:103B JIS C 7021: B-11 Endurance Test Thermal Shock Test Solderability Test Environmental Test Temperature Cycling Solderability Test 1.IR-Reflow In-Board,2 times 2.Ta=105℃±5℃& -40℃±5℃ (10min) (10min) 3.total 10 cycles MIL-STD-202F: 107D MIL-STD-750D: 1051 MIL-STD-883D: 1011 1.T.Sol=235℃±5℃ 2.Immersion time 2±0.5sec 3.Immersion rate 25±2.5mm/sec 4.Immersion rate 25±2.5mm/sec 5.Coverage ≧95% of the dipped surface MIL-STD-202F: 208D MIL-STD-750D: 2026 MIL-STD-883D: 2003 IEC 68 Part 2-20 JIS C 7021: A-2 1.105℃ ~ 25℃ ~ 55℃ ~ 25℃ 30mins 5mins 30mins 5mins 2.10 Cyeles MIL-STD-202F: 107D MIL-STD-750D: 1051 MIL-STD-883D: 1010 JIS C 7021: A-4 Ramp-up rate(183℃ to Peak) +3℃ second max Temp. maintain at 125(±25)℃ 120 seconds max Temp. maintain above 183℃ 60-150 seconds Peak temperature range 235℃ +5-0℃ Time within 5℃ of actual Peak Temperature(tp) 10-30 seconds Ramp-down rate +6℃/second max MIL-STD-750D:2031.2 J-STD-020