LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only SURFACE MOUNT TYPE AND REEL LVY9033/TR2 DATA SHEET DOC. NO : QW0905-LVY9033/TR2 REV. : A DATE : 09 - Jun - 2005 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 1/8 PART NO. LVY9033/TR2 Package Dimensions Cathode 2.5 0.4±0.1 0.5±0.1 2.0 5.8 ±0.5 ψ1.9 3.05 ±0.5 1.4 2.8 0.7 4.3 ±0.5 Note : 1.All dimension are in millimeter tolerance is ±0.2mm unless otherwise noted. 2.Specifications are subject to change without notice. Carrier Type Dimensions t B0 W1 W F Polarity E Do P2 Cathode Note : The tolerances unless mentioned is ±0.2mm,Angle ± 0.5. Unit=mm. Ko P Po LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 2/8 PART NO. LVY9033/TR2 Reel Dimensions 16.0±1.0 ψ178±2.0 14.2±1.0 74.0±1.5 Part No. Description Quantity/Reel LVY9033/TR2 12.0mm tape,7"reel 1500 devices LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LVY9033/TR2 Page 3/8 Absolute Maximum Ratings at Ta=25 ℃ Ratings Symbol Parameter UNIT VY Forward Current IF 30 mA Peak Forward Current Duty 1/10@10KHz IFP 60 mA Power Dissipation PD 75 mW Reverse Current @5V Ir 10 μA Electrostatic Discharge ESD 2000 V Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40~ +100 ℃ Soldering Temperature Tsol Max 260 ℃ for 5 sec Max Typical Electrical & Optical Characteristics (Ta=25 ℃) PART NO COLOR MATERIAL Emitted LVY9033/TR2 AlGaInP Yellow Dominant wave length λDnm Spectral halfwidth △λnm Lens Water Clear 590 20 Forward voltage @20mA(V) Min. Max. 1.7 2.6 Note : 1.The forward voltage data did not including ±0.1V testing tolerance. 2. The luminous intensity data did not including ±15% testing tolerance. Luminous intensity @20mA(mcd) Viewing angle 2θ 1/2 (deg) Min. Typ. 220 450 20 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page4/8 PART NO. LVY9033/TR2 Typical Electro-Optical Characteristics Curve VY CHIP Fig.2 Relative Intensity vs. Forward Current Fig.1 Forward current vs. Forward Voltage 3.0 Relative Intensity Normalize @20mA Forward Current(mA) 1000 100 10 1.0 0.1 1.0 1.5 2.0 2.5 2.5 2.0 1.5 1.0 0.5 0.0 1.0 3.0 10 Fig.3 Forward Voltage vs. Temperature Fig.4 Relative Intensity vs. Temperature 1.2 3.0 Relative Intensity@20mA Normalize @25 ℃ Forward Voltage@20mA Normalize @25 ℃ 1000 Forward Current(mA) Forward Voltage(V) 1.1 1.0 0.9 0.8 -40 -20 0 20 40 60 80 100 Fig.5 Relative Intensity vs. Wavelength 1.0 0.5 0.0 500 550 600 Wavelength (nm) 2.5 2.0 1.5 1.0 0.5 0.0 -40 -20 0 20 40 60 80 Ambient Temperature( ℃) Ambient Temperature( ℃) Relative Intensity@20mA 100 650 100 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 5/8 PART NO. LVY9033/TR2 Soldering Iron: Basic spec is ≦5 sec when 260 ℃. If temperature is higher, time should be shorter(+10 ℃ → -1sec). Power dissipation of iron should be smaller than 15W,and temperature should be controllable. Surface temperature of the device should be under 230 ℃. Soldering heat Soldering heat Max. 260 ℃ 245±5℃ within 5 sec 120 ~ 150 ℃ Preheat 120 ~ 180 sec Reflow Temp/Time Temp. (℃) 220 Rising +5℃/sec 150 Cooling -5℃/sec Preheat 120 60 ~ 120 sec 5sec Time LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LVY9033/TR2 Page 6/8 Precautions For Use: Storage time: 1.The operation of Temperatures and RH are : 5 ℃~35℃,RH60%. 2.Once the package is opened, the products should be used within a week. Otherwise, they should be kept in a damp proof box with descanting agent. Considering the tape life, we suggest our customers to use our products within a year(from production date). 3.If opened more than one week in an atmosphere 5 ℃ ~ 35℃,RH60%, they should be treated at 60 ℃±5 ℃fo r 15hrs. Drive Method: LED is a current operated device, and therefore, requirer some kind of current limiting incorporated into the driver circuit. This current limiting typically takes the form of a current limiting resistor placed in series with the LED. Consider worst case voltage variations than could occur across the current limiting resistor. The forwrd current should not be allowed to change by more than 40 % of its desired value. Circuit model A Circuit model B LED LED (A) Recommended circuit. (B) The difference of brightness between LED could be found due to the VF-IF characteristics of LED. Cleaning: Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED. ESD(Electrostatic Discharge): Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 7/8 PART NO. LVY9033/TR2 Reliability Test: Classification Test Item Test Condition Reference Standard Operating Life Test 1.Ta=Under Room Temperature As Per Data Sheet Maximum Rating. 2.If=20mA 3.t=1000 hrs (-24hrs, +72hrs) MIL-STD-750D: 1026 MIL-STD-883D: 1005 JIS C 7021: B-1 High Temperature Storage Test 1.Ta=105 ℃±5℃ 2.t=1000 hrs (-24hrs, +72hrs) MIL-STD-883D:1008 JIS C 7021: B-10 Low Temperature Storage Test 1.Ta=-40 ℃±5℃ 2.t=1000 hrs (-24hrs, +72hrs) JIS C 7021: B-12 High Temperature High Humidity Storage Test 1.IR-Reflow In-Board, 2 Times 2.Ta=65 ℃±5℃ 3.RH=90%~95% 4.t=1000hrs ±2hrs MIL-STD-202F:103B JIS C 7021: B-11 Endurance Test Thermal Shock Test Solderability Test Temperature Cycling 1.IR-Reflow In-Board,2 times 2.Ta=105 ℃±5℃& -40 ℃±5℃ (10min) (10min) 3.total 10 cycles MIL-STD-202F: 107D MIL-STD-750D: 1051 MIL-STD-883D: 1011 1.T.Sol=235 ℃±5℃ 2.Immersion time 2 ±0.5sec 3.Immersion rate 25 ±2.5mm/sec 4.Immersion rate 25 ±2.5mm/sec 5.Coverage ≧95% of the dipped surface MIL-STD-202F: 208D MIL-STD-750D: 2026 MIL-STD-883D: 2003 IEC 68 Part 2-20 JIS C 7021: A-2 1.105 ℃ ~ 25℃ ~ 55℃ ~ 25℃ 30mins 5mins 30mins 5mins 2.10 Cyeles MIL-STD-202F: 107D MIL-STD-750D: 1051 MIL-STD-883D: 1010 JIS C 7021: A-4 Ramp-up rate(183 ℃ to Peak) +3 ℃ second max Temp. maintain at 125( ±25)℃ 120 seconds max Temp. maintain above 183 ℃ 60-150 seconds Peak temperature range 235 ℃+5-0 ℃ Time within 5℃ of actual Peak Temperature(tp) 10-30 seconds Ramp-down rate +6 ℃/second max MIL-STD-750D:2031.2 J-STD-020 Environmental Test Solderability Test LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 8/8 PART NO. LVY9033/TR2 . MAIN RAW MATERIAL LIST ITEM 1 2 3 MATERIAL Yellow Chip (AlGaInP) 銀膠 (Silver Epoxy) 支架 (Lead Frame ) MODEL ED-M80HYU 826-1 2005-9 4 gold wire φ0.1mil Au 5 Epoxy NT-301H-11000 SUPPLIER ORIGIN 光磊科技股份有限公司 台灣 (OPTO TECH CORPORATION ) TAIWAN ABLESTIK 美國 USA 巨貿精密工業股份有限公司 台灣 (TTOP CORPORATION ) TAIWAN AMERICAN FINE WIRE 美國 USA 台灣日東電工股份有限公司 台灣 (NITTO DENKO (TAIWAN) CORPORATION ) TAIWAN