LITEON LTL2H3KRK-012A

LITE-ON ELECTRONICS, INC.
Property of Lite-On Only
Features
* High luminous intensity output.
* Low power consumption.
* High efficiency.
* Versatile mounting on P.C. board or panel.
* I.C. Compatible/low current requirements.
* Popular T-13/4 diameter.
Package Dimensions
Part No.
Lens
Source Color
LTL2H3KRK-012A
Water Clear
AlInGaP Super Red
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25mm(.010") unless otherwise noted.
3. Protruded resin under flange is 1.0mm(.04") max.
4. Lead spacing is measured where the leads emerge from the package.
5. Specifications are subject to change without notice.
Part No. : LTL2H3KRK-012A
BNS-OD-C131/A4
Page :
1
of
5
LITE-ON ELECTRONICS, INC.
Property of Lite-On Only
Absolute Maximum Ratings at TA=25℃
Parameter
Maximum Rating
Unit
75
mW
90
mA
Continuous Forward Current
30
mA
Derating Linear From 50℃
0.4
mA/℃
5
V
Power Dissipation
Peak Forward Current
(1/10 Duty Cycle, 0.1ms Pulse Width)
Reverse Voltage
Operating Temperature Range
-40℃ to + 100℃
Storage Temperature Range
-55℃ to + 100℃
Lead Soldering Temperature
[1.6mm(.063") From Body]
Part No. : LTL2H3KRK-012A
BNS-OD-C131/A4
260℃ for 5 Seconds
Page :
2
of
5
LITE-ON ELECTRONICS, INC.
Property of Lite-On Only
Electrical / Optical Characteristics at TA=25℃
Parameter
Symbol
Min.
Typ.
IV
560
1300
mcd
2θ1/2
15
deg
Peak Emission Wavelength
λP
639
nm
Dominant Wavelength
λd
631
nm
Δλ
20
nm
Forward Voltage
VF
2.0
Reverse Current
IR
Capacitance
C
Luminous Intensity
Viewing Angle
Spectral Line Half-Width
40
Max.
Unit
2.4
V
100
μA
pF
Test Condition
IF = 20mA
Note 1
Note 2 (Fig.5)
Measurement
@Peak (Fig.1)
Note 4
IF = 20mA
VR = 5V
VF = 0 , f = 1MHz
NOTE: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE
eye-response curve.
2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity.
3. Iv classification code is marked on each packing bag.
4. The dominant wavelength, λd is derived from the CIE chromaticity diagram and represents the
single wavelength which defines the color of the device.
Part No. : LTL2H3KRK-012A
BNS-OD-C131/A4
Page :
3
of
5
LITE-ON ELECTRONICS, INC.
Property of Lite-On Only
Typical Electrical / Optical Characteristics Curves
(25℃ Ambient Temperature Unless Otherwise Noted)
Part No. : LTL2H3KRK-012A
BNS-OD-C131/A4
Page :
4
of
5
LITE-ON ELECTRONICS, INC.
Property of Lite-On Only
Features
* Compatible with radial lead automatic insertion equipment.
* Most radial lead plastic lead lamps available packaged in tape and folding.
* 2.54mm (0.1") straight lead spacing available.
* Folding packaging simplifies handling and testing.
Package Dimensions
Specification
Item
Symbol
Minimum
Maximum
mm
inch
mm
inch
Tape Feed Hole Diameter
D
3.8
0.149
4.2
0.165
Component Lead Pitch
F
2.3
0.091
3.0
0.118
Front to Rear Deflection
△H
--
--
2.0
0.078
Feed Hole to Bottom of Component
H1
21.5
0.846
22.5
0.886
Feed Hole to Overall Component Height
H2
29.9
1.177
31.5
1.240
11.0
0.433
Lead Length After Component Height
L
Feed Hole Pitch
P
12.4
0.488
13.0
0.511
Lead Location
P1
4.4
0.173
5.8
0.228
Center of Component Location
P2
5.05
0.198
7.65
0.301
Total Tape Thickness
T
--
--
0.90
0.035
Feed Hole Location
W0
8.5
0.334
9.75
0.384
Adhesive Tape Width
W1
14.5
0.571
15.5
0.610
Adhesive Tape Position
W2
0
0
3.0
0.118
Tape Width
W3
17.5
0.689
19.0
0.748
Page : 5
of
Part No. : LTL2H3KRK-012A
BNS-OD-C131/A4
W0
5