LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Technical Data Ultra Bright LED Lamp for Traffic Sign LTL2P3SEKS-0D2A Red (22o) LTL2R3SEKS-0D2A Red (30o) LTL2P3SYKS-0D2A Amber (22o) LTL2R3SYKS-0D2A Amber (30o) Benefits * Lower system cost. Description * Higher luminous efficiency than incandescent lamp. The source color light emitting diode dice of these devices is * Fewer LED are required due to the TS AlInGaP made of AlInGaP on a transparent substrate (TS). The water clear epoxy lens on these devices create viewing technology. angles of 22 and 30 degrees that match international Features specifications for traffic sign utilization. * High luminous intensity output. These LED lamps provide superior endurance against * Low power consumption. moisture and high temperatures thus are reliable for outdoor * High efficiency. environment use. With a lower power consumption than * Versatile mounting on PCB or panel. traditional incandescent lamps, these devices yield lower * I.C. Compatible / low current requirements. system cost. 3 * Popular T-1 4 diameter (5 mm). Applications * Traffic signals. * Versatile warning signals. * Outdoor traffic display panels. Part No. : LTL2P3SEKS-0D2A \ LTL2P3SYKS-0D2A LTL2R3SEKS-0D2A \ LTL2R3SYKS-0D2A BNS-OD-C131/A4 Selection Guide Part No Color Iv(mcd) Va λd(nm) LTL2P3SEKS Red 4800 22o 630 LTL2R3SEKS Red 3700 30 o 630 LTL2P3SYKS Amber 3700 22 o 590 LTL2R3SYKS Amber 2800 30 o 590 Page : 1 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Package Dimensions LTL2P3xS Series LTL2R3xS Series Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25mm(.010") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. Specifications are subject to change without notice. Part No. : LTL2P3SEKS-0D2A \ LTL2P3SYKS-0D2A LTL2R3SEKS-0D2A \ LTL2R3SYKS-0D2A BNS-OD-C131/A4 Page : 2 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Absolute Maximum Ratings at TA=25 °C Parameter Maximum Rating Unit 130 mW 100 mA Continuous Forward Current 50 mA Derating Linear From 50 °C 0.6 mA/℃ 5 V Power Dissipation Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) Reverse Voltage Operating Temperature Range -40°C to + 80°C Storage Temperature Range -55°C to + 100°C Lead Soldering Temperature [1.6mm(.063") From Body] 260°C for 5 Seconds Part No. : LTL2P3SEKS-0D2A \ LTL2P3SYKS-0D2A LTL2R3SEKS-0D2A \ LTL2R3SYKS-0D2A BNS-OD-C131/A4 Page : 3 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Electrical / Optical Characteristics at TA=25 °C Parameter Luminous Intensity Viewing Angle Peak Emission Wavelength Dominant Wavelength Spectral Line Half-Width Symbol IV 2θ1/2 λP λd ∆λ Forward Voltage VF Reverse Current IR Capacitance C Part NO. Min. Typ. 2P3SEKS 2500 4800 2R3SEKS 1900 3700 2P3SYKS 1900 3700 2R3SYKS 1900 2800 (LTL) Max. mcd 2P3SXKS 22 2R3SXKS 30 Red 639 Amber 591 Red 630 Amber 590 Red 17 Amber 17 Red 2.25 2.7 Amber 2.35 2.7 deg nm nm Test Condition IF = 20mA Note 1 Note 2 (Fig.5) Measurement @Peak (Fig.1) Note 4 nm 100 40 Unit V IF = 20mA µA VR = 5V pF VF = 0 , f = 1MHz NOTE: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve. 2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 3. Iv classification code is marked on each packing bag. 4. The dominant wavelength, λd is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. Part No. : LTL2P3SEKS-0D2A \ LTL2P3SYKS-0D2A LTL2R3SEKS-0D2A \ LTL2R3SYKS-0D2A BNS-OD-C131/A4 Page : 4 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Typical Electrical / Optical Characteristics Curves (25 °C Ambient Temperature Unless Otherwise Noted) Part No. : LTL2P3SEKS-0D2A \ LTL2P3SYKS-0D2A LTL2R3SEKS-0D2A \ LTL2R3SYKS-0D2A BNS-OD-C131/A4 Page : 5 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Features * Compatible with radial lead automatic insertion equipment. * Most radial lead plastic lead lamps available packaged in tape and folding. * 2.54mm (0.1") straight lead spacing available. * Folding packaging simplifies handling and testing. Reel packaging is available by removing suffix “A” on option. Package Dimensions Item Tape Feed Hole Diameter Component Lead Pitch Front to Rear Deflection Feed Hole to Bottom of Component Feed Hole to Overall Component Height Lead Length After Component Height Feed Hole Pitch Lead Location Center of Component Location Total Tape Thickness Feed Hole Location Adhesive Tape Width Adhesive Tape Position Tape Width Symbol D F △H H1 H2 L P P1 P2 T W0 W1 W2 W3 Specification Minimum Maximum mm inch mm inch 3.8 0.149 4.2 0.165 2.3 0.091 3.0 0.118 --2.0 0.078 19.5 0.768 21.5 0.847 27.9 1.098 30.5 1.201 W0 12.4 0.488 4.4 0.173 5.05 0.198 --8.5 0.334 14.5 0.571 0 0 17.5 0.689 11.0 13.0 5.8 7.65 0.90 9.75 15.5 3.0 19.0 0.433 0.511 0.228 0.301 0.035 0.384 0.610 0.118 0.748 Part No. : LTL2P3SEKS-0D2A \ LTL2P3SYKS-0D2A LTL2R3SEKS-0D2A \ LTL2R3SYKS-0D2A BNS-OD-C131/A4 Page : 6 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Packing Spec 2000 pcs per inner carton 10 Inner cartons per outer carton total 20000 pcs per outer carton In every shipping lot, only the last pack will be non-full packing Part No. : LTL2P3SEKS-0D2A \ LTL2P3SYKS-0D2A LTL2R3SEKS-0D2A \ LTL2R3SYKS-0D2A BNS-OD-C131/A4 Page : 7 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Bin Code List For Reference Luminous Intensity Iv(mcd) Bin Code S T U V W X Min. 1900 2500 3200 4200 5500 7200 IF@20mA Max. 2500 3200 4200 5500 7200 9300 Note: Tolerance of each bin limit is ±15% Dominant Wavelength λd(nm) IF@20mA Bin Code Min. Max. A 584.5 587.0 B 587.0 589.5 C 589.5 592.0 D 592.0 594.5 E 594.5 597.0 Note: Tolerance of each bin limit is ±1nm Forward Voltage Vf (Volts) IF@20mA Bin Code Min. Max. 1 1.8 1.9 2 1.9 2.0 3 2.0 2.1 4 2.1 2.2 5 2.2 2.3 6 2.3 2.4 7 2.4 2.5 8 2.5 2.6 9 2.6 2.7 Part No. : LTL2P3SEKS-0D2A \ LTL2P3SYKS-0D2A LTL2R3SEKS-0D2A \ LTL2R3SYKS-0D2A BNS-OD-C131/A4 Page : 8 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only CAUTIONS 1. Application The LEDs described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household applications).Consult Liteon’s Sales in advance for information on applications in which exceptional reliability is required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment, medical and life support systems and safety devices). 2. Storage The storage ambient for the LEDs should not exceed 30°C temperature or 70% relative humidity. It is recommended that LEDs out of their original packaging are used within three months. For extended storage out of their original packaging, it is recommended that the LEDs be stored in a sealed container with appropriate desiccant or in desiccators with nitrogen ambient. 3. Cleaning Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LEDs if necessary. 4. Lead Forming & Assembly During lead forming, the leads should be bent at a point at least 3mm from the base of LED lens. Do not use the base of the lead frame as a fulcrum during forming. Lead forming must be done before soldering, at normal temperature. During assembly on PCB, use minimum clinch force possible to avoid excessive mechanical stress. 5. Soldering When soldering, leave a minimum of 2mm clearance from the base of the lens to the soldering point. Dipping the lens into the solder must be avoided. Do not apply any external stress to the lead frame during soldering while the LED is at high temperature. Recommended soldering conditions : Soldering iron Temperature Soldering time 300°C Max. 3 sec. Max. (one time only) Wave soldering Pre-heat Pre-heat time Solder wave Soldering time 100°C Max. 60 sec. Max. 260°C Max. 10 sec. Max. Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or catastrophic failure of the LED Part No. : LTL2P3SEKS-0D2A \ LTL2P3SYKS-0D2A LTL2R3SEKS-0D2A \ LTL2R3SYKS-0D2A BNS-OD-C131/A4 Page : 9 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only 6. Drive Method An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs connected in parallel in an application, it is recommended that a current limiting resistor be incorporated in the drive circuit, in series with each LED as shown in Circuit A below. Circuit model A Circuit model B LED LED (A) Recommended circuit (B) The brightness of each LED might appear different due to the differences in the I-V characteristics of those LEDs 7. ESD (Electrostatic Discharge) Static Electricity or power surge will damage the LED. Suggestions to prevent ESD damage: Use a conductive wrist band or anti- electrostatic glove when handling these LEDs All devices, equipment, and machinery must be properly grounded Work tables, storage racks, etc. should be properly grounded Use ion blower to neutralize the static charge which might have built up on surface of the LEDs plastic lens as a result of friction between LEDs during storage and handing Part No. : LTL2P3SEKS-0D2A \ LTL2P3SYKS-0D2A LTL2R3SEKS-0D2A \ LTL2R3SYKS-0D2A BNS-OD-C131/A4 Page : 10 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Suggested checking list : Training and Certification 1. Everyone working in a static-safe area is ESD-certified? 2. Training records kept and re-certification dates monitored? Static-Safe Workstation & Work Areas 1. Static-safe workstation or work-areas have ESD signs? 2. All surfaces and objects at all static-safe workstation and within 1 ft measure less than 100V? 3. All ionizer activated, positioned towards the units? 4. Each work surface mats grounding is good? Personnel Grounding 1. Every person (including visitors) handling ESD sensitive (ESDS) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 2. If conductive footwear used, conductive flooring also present where operator stand or walk? 3. Garments, hairs or anything closer than 1 ft to ESD items measure less than 100V*? 4. Every wrist strap or heel strap/conductive shoes checked daily and result recorded for all DSL? 5. All wrist strap or heel strap checkers calibration up to date? Note: *50V for Blue LED. Device Handling 1. Every ESDS items identified by EIA-471 labels on item or packaging? 2. All ESDS items completely inside properly closed static-shielding containers when not at static-safe workstation? 3. No static charge generators (e.g. plastics) inside shielding containers with ESDS items? 4. All flexible conductive and dissipative package materials inspected before reuse or recycle? Others 1. Audit result reported to entity ESD control coordinator? 2. Corrective action from previous audits completed? 3. Are audit records complete and on file? Part No. : LTL2P3SEKS-0D2A \ LTL2P3SYKS-0D2A LTL2R3SEKS-0D2A \ LTL2R3SYKS-0D2A BNS-OD-C131/A4 Page : 11 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only 8. Reliability Test Classification Test Item Operation Life High Temperature High Humidity Storage Endurance Test Environmental Test High Temperature High Humidity Reverse BIAS Test Condition Reference Standard Ta= Under Room Temperature As Per Data Sheet Maximum Rating *Test Time= 1000HRS (-24HRS,+72HRS) MIL-STD-750D:1026 (1995) MIL-STD-883D:1005 (1991) JIS C 7021:B-1 (1982) Ta= 65±5℃ RH= 90 〜 95% MIL-STD-202F: 103B(1980) JIS C 7021 : B-11(1982) Test Time= 240HRS±2HRS Ta= 65±5℃ RH= 90 〜 95% VR=5V Test Time = 500HRS (-24HRS, +48HRS) JIS C 7021 : B-11(1982) High Temperature Storage Ta= 105±5℃ *Test Time= 1000HRS (-24HRS,+72HRS) MIL-STD-883D:1008 (1991) JIS C 7021:B-10 (1982) Low Temperature Storage Ta= -55±5℃ *Test Time=1000HRS (-24HRS,+72HRS) JIS C 7021:B-12 (1982) Temperature Cycling 105℃ 〜 25℃ 〜 -55℃ 〜 25℃ 30mins 5mins 30mins 5mins 10 Cycles MIL-STD-202F:107D (1980) MIL-STD-750D:1051(1995) MIL-STD-883D:1010 (1991) JIS C 7021: A-4(1982) Thermal Shock 105 ± 5℃ 〜 -55℃ ± 5℃ 10mins 10mins 10 Cycles MIL-STD-202F:107D(1980) MIL-STD-750D:1051(1995) MIL-STD-883D:1011 (1991) Solder Resistance T.sol = 260 ± 5℃ Dwell Time= 10 ± 1secs MIL-STD-202F:210A(1980) MIL-STD-750D:2031(1995) JIS C 7021: A-1(1982) T. sol = 230 ± 5℃ Dwell Time= 5 ± 1secs MIL-STD-202F:208D(1980) MIL-STD-750D:2026(1995) MIL-STD-883D:2003(1991) JIS C 7021: A-2(1982) Solderability 9. Others The appearance and specifications of the product may be modified for improvement, without prior notice. Part No. : LTL2P3SEKS-0D2A \ LTL2P3SYKS-0D2A LTL2R3SEKS-0D2A \ LTL2R3SYKS-0D2A BNS-OD-C131/A4 Page : 12 of 12