LITEON LTP-14088KD-J

LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
LED DISPLAY
LTP-14088KD-J
DATA SHEET
Rev
Description
01
RDR Original Spec
-
NPPR Original Spec
SPEC. NO.:
DATE
:
December 01, 2008
Phanomkorn J.
December 19, 2008
December 19, 2008
0
PART NO.: LTP-14088KD-J
BNS-OD-C131/A4
Phanomkorn J.
DS30-2008-0194
REV. NO. :
PAGE NO. :
By
OF 5
PAGE:
0
of 5
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
FEATURES
*1.50 inch ( 37.0 mm) MATRIX HEIGHT
*LOW POWER REQUIREMENT
*SINGLE PLANE, WIDE VIEWING ANGLE
*SOLID STATE RELIABILITY
*8 ×8 ARRAY WITH X-Y SELECT
*COMPATIBLE WITH USASCII AND EBCDIC CODES
*STACKABLE HORIZONTALLY
*CATEGORIZED FOR LUMINOUS INTENSITY
*LEAD-FREE PACKAGE(ACCORDING TO RoHS)
DESCRIPTION
The LTP-14088KD-J is a 1.50 inch (37.0 mm) matrix height 8×8 dot
matrix display. This device uses AS-AlInGaP Hyper Red LED chips
(AlInGaP epi on GaAs substrate). The matrix display has a black face
and white dot color.
DEVICE
PART NO.
DESCRIPTION
AlInGaP Hyper Red
Anode Column
Cathode Row
LTP-14088KD-J
PART NO.: LTP-14088KD-J
BNS-OD-C131/A4
PAGE:
1
of 5
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
PACKAGE DIMENSIONS
NOTES: 1. All dimensions are in millimeters. Tolerances are± 0.25 mm (0.01“) unless otherwise noted.
2. Pin tip’s shift tolerance is +/- 0.4 mm.
3. Foreign material on segment ≦10mils
4. Ink contamination (surface) ≦20mils
5. Bending≦1/100
6. Bubble in segment ≦10mils
INTERNAL CIRCUIT DIAGRAM
PART NO.: LTP-14088KD-J
BNS-OD-C131/A4
PAGE:
2
of 5
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
PIN CONNECTION
NO
CONNECTION
1
CATHODE ROW 5
2
CATHODE ROW 7
3
ANODE COLUMN 2
4
ANODE COLUMN 3
5
CATHODE ROW 8
6
ANODE COLUMN 5
7
CATHODE ROW 6
8
CATHODE ROW 3
9
CATHODE ROW 1
10
ANODE COLUMN 4
11
ANODE COLUMN 6
12
CATHODE ROW 4
13
ANODE COLUMN 1
14
CATHODE ROW 2
15
ANODE COLUMN 7
16
ANODE COLUMN 8
PART NO.: LTP-14088KD-J
BNS-OD-C131/A4
PAGE:
3
of 5
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
ABSOLUTE MAXIMUM RATING
PARAMETER
MAXIMUM RATING
UNIT
Average Power Dissipation Per Dot
70
mW
Peak Forward Current Per Dot
( Frequency 1Khz,18% duty cycle)
90
mA
25
0.28
mA
mA/℃
Average Forward Current Per Dot
Derating Linear From 25℃ Per Dot
Reverse Voltage Per Segment
Operating Temperature Range
5
-35℃ to +105℃
Storage Temperature Range
-35℃ to +105℃
V
Soldering Conditions: 1/16 inch below seating plane for 3 seconds at 2600C
or of temperature unit (during assembly) not over max. temperature rating above.
ELECTRICAL / OPTICAL CHARACTERISTICS AT Ta=25oC
PARAMETER
SYMBOL MIN. TYP. MAX. UNIT TEST CONDITION
Average Luminous Intensity
IV
1020 2475
µcd
Ip=32mA 1/16Duty
Peak Emission Wavelength
λp
650
nm
IF=20mA
Spectral Line Half-Width
∆λ
20
nm
IF=20mA
Dominant Wavelength
λd
639
nm
IF=20mA
Forward Voltage any Dot
VF
Reverse Current any Dot
IR
100
IV-m
2:1
Luminous Intensity Matching Ratio
(Similar Light Area)
2.1
2.6
2.3
2.8
IF=20mA
V
IF=80mA
µA
VR=5V
Ip=32mA 1/16Duty
Note: Luminous intensity is measured with a light sensor and filter combination that
approximates the CIE (Commision Internationale De L’Eclairage) eye-response curve.
PART NO.: LTP-14088KD-J
BNS-OD-C131/A4
PAGE:
4
of 5
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
TYPICAL ELECTRICAL / OPTICAL CHARACTERISTIC CURVES
(25oC Ambient Temperature Unless Otherwise Noted)
PART NO.: LTP-14088KD-J
BNS-OD-C131/A4
PAGE:
5
of 5