LITEON LTW-E670DS-STE

LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Features
*
*
*
*
*
*
Package in 8mm tape on 7" diameter reels.
Compatible with automatic placement equipment.
Compatible with infrared and vapor phase reflow solder process.
EIA STD package.
I.C. compatible.
Meet green product and Pb-free(According to RoHS)
Package
Dimensions
Part No.
Lens Color
Source Color
LTW-E670DS-STE
Yellow
InGaN White
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.2 mm (.008") unless otherwise noted.
Part No. : LTW-E670DS-STE
BNS-OD-C131/A4
Page :
1
of
11
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
℃
Absolute Maximum Ratings at Ta=25℃
Parameter
LTW-E670DS-STE
Unit
120
mW
(1/10 Duty Cycle, 0.1ms Pulse Width)
100
mA
DC Forward Current
50
mA
30000
hrs
5
V
Power Dissipation
Peak Forward Current
Life time
(IF = 30mA )
Reverse Voltage
Operating Temperature Range
-30℃ to + 85℃
Storage Temperature Range
-40℃ to + 100℃
Wave Soldering Condition
260℃ For 5 Seconds
Suggest IR Reflow Condition :
IR-Reflow Soldering Profile for lead free soldering (Acc. to J-STD-020B)
Part No. : LTW-E670DS-STE
BNS-OD-C131/A4
Page :
2
of
11
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Electrical
Optical
Characteristics
At
℃
Ta=25℃
Symbol
Part No.
LTW-
Min.
Luminous Intensity
IV
E670DS-STE
1400
Luminous Flux
ΦV
E670DS-STE
Viewing Angle
2θ1/2
E670DS-STE
Parameter
x
Chromaticity Coordinates
Typ.
Max.
Unit
Test Condition
3550
mcd
IF = 30mA
Note 1, 2, 5
5000
mlm
IF = 30mA
Note 1, 2, 5
120
deg
Fig.6
IF = 30mA
Note 3, 5
Fig.1
0.32
E670DS-STE
y
0.32
Forward Voltage
VF
E670DS-STE
Reverse Current
IR
E670DS-STE
2.8
3.6
4.0
V
IF = 30mA
10
µA
VR = 5V
Note: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE
eye-response curve.
2. Iv classification code is marked on each packing bag.
3. The chromaticity coordinates (x, y) is derived from the 1931 CIE chromaticity diagram.
4. Caution in ESD:
Static Electricity and surge damages the LED. It is recommended using a wrist band or anti-electrostatic
glove when handling the LED. All devices, equipment and machinery must be properly grounded.
5. CAS140B is the test standard for the chromaticity coordinates (x, y) & IV.
Part
No. : LTW-E670DS-STE
BNS-OD-C131/A4
Page :
3
of
11
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Bin Code List
IV Spec. Table
Luminous Intensity (mcd) at IF = 30mA
IV Bin
Luminous Flux (mlm)
Min.
Max.
Typ.
W1
1120
1400
3600
W2
1400
1800
4400
X1
1800
2240
5200
X2
2240
2800
6000
Y1
2800
3550
6800
Tolerance on each Luminous Intensity bin is +/- 15%.
Hue Spec. Table
Color bin limits at IF = 30mA
Hue Bin
5L
6L
CIE 1931 Chromaticity coordinates
x
0.291
0.285
0.307
0.310
y
0.268
0.279
0.312
0.297
x
0.310
0.307
0.330
0.330
y
0.297
0.312
0.347
0.330
Tolerance on each Hue (x, y) bin is +/- 0.02
Part
No. : LTW-E670DS-STE
BNS-OD-C131/A4
Page :
4
of
11
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
0.4
0.38
0.36
Y-coordinate
0.34
D
0.32
C
0.3
6L
B
0.28
A
0.26
0.24
0.22
0.2
0.2
Part
0.22
No. : LTW-E670DS-STE
BNS-OD-C131/A4
0.24
0.26
0.28
0.3
0.32
X-coordinate
0.34
Page :
5
0.36
of
0.38
11
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Typical Electrical / Optical Characteristics Curves
Relative Intensity
(25°° C Ambient Temperature Unless Otherwise Noted)
1.0
0.5
0.0
350
450
550
650
750
wavelength (nm)
Fig.1 RELATIVE INTENSITY VS. WAVELENGTH
Part No. : LTW-E670DS-STE
BNS-OD-C131/A
Page :
6
of
11
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
User Guide
Cleaning
Do not use unspecified chemical liquid to clean LED they could harm the package.
If cleaning is necessary, immerse the LED in ethyl alcohol or isopropyl alcohol at normal temperature
for less than one minute.
Recommend Printed Circuit Board Attachment Pad
Infrared / vapor phase
Reflow Soldering
Package Dimensions of Tape
Note:
1. All dimensions are in millimeters (inches).
Part No. : LTW-E670DS-STE
BNS-OD-C131/A4
Page :
7
of
11
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Package Dimensions of Reel
Notes:
1. Empty component pockets sealed with top cover tape.
2. 13 inch reel-8000 pieces per reel.
3. Minimum packing quantity is 4000 pieces for remainders.
4. The maximum number of consecutive missing lamps is two.
5. In accordance with EIA-481-1-B specifications.
Part No. : LTW-E670DS-STE
BNS-OD-C131/A4
Page :
8
of
11
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
CAUTIONS
1. Application
The LEDs described here are intended to be used for ordinary electronic equipment (such as office
equipment, communication equipment and household applications).Consult Liteon’s Sales in advance
for information on applications in which exceptional reliability is required, particularly when the failure
or malfunction of the LEDs may directly jeopardize life or health (such as in aviation, transportation,
traffic control equipment, medical and life support systems and safety devices).
2. Storage
This product is qualified as Moisture sensitive Level 3 per JEDEC J-STD-020 Precaution when handing
this moisture sensitive product is important to ensure the reliability of the product.
The package is sealed:
The LEDs should be stored at 30°C or less and 90%RH or less. And the LEDs are limited to use within
one year, while the LEDs is packed in moisture-proof package with the desiccants inside.
The package is opened:
The LEDs should be stored at 30°C or less and 60%RH or less. Moreover, the LEDs are limited to solder
process within 168hrs. If the Humidity Indicator shows the pink color in 10% even higher or exceed the
storage limiting time since opened, that we recommended to baking LEDs at 60°C at least 48hrs. To seal
the remainder LEDs return to package, it’s recommended to be with workable desiccants in original
package.
3. Cleaning
Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED if necessary.
4. Soldering
Recommended soldering conditions:
Reflow soldering
Wave Soldering
Pre-heat
120~150°C
Pre-heat time
120 sec. Max.
Soldering Temp. 260°C Max.
Soldering time
30 sec. Max.
Pre-heat
Pre-heat time
Solder wave
Soldering time
Soldering iron
100°C Max.
60 sec. Max.
260°C Max.
10 sec. Max.
Temperature
Soldering time
300°C Max.
3 sec. Max.
(one time only)
5. Drive Method
An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs
connected in parallel in an application, it is recommended that a current limiting resistor be incorporated
in the drive circuit, in series with each LED as shown in Circuit A below.
Circuit model A
LED
Circuit model B
LED
(A) Recommended circuit.
(B) The brightness of each LED might appear different due to the differences in the I-V characteristics of
those LEDs.
6. ESD (Electrostatic Discharge)
Static Electricity or power surge will damage the LED.
Suggestions to prevent ESD damage:
Part No. : LTW-E670DS-STE
BNS-OD-C131/A4
Page :
9
of
11
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Use of a conductive wrist band or anti-electrostatic glove when handling these LEDs.
All devices, equipment, and machinery must be properly grounded.
Work tables, storage racks, etc. should be properly grounded.
Use ion blower to neutralize the static charge which might have built up on surface of the LED’s plastic
lens as a result of friction between LEDs during storage and handling.
ESD-damaged LEDs will exhibit abnormal characteristics such as high reverse leakage current, low forward
voltage, or “no lightup” at low currents.
To verify for ESD damage, check for “light up” and Vf of the suspect LEDs at low currents.
The Vf of “good” LEDs should be >[email protected] for InGaN product and >[email protected] for AlInGaP
product.
7. Reliability Test
Classification
Test Item
Test Condition
Reference Standard
Ta= Under Room Temperature As Per Data Sheet
Maximum Rating
*Test Time= 1000HRS (-24HRS,+72HRS)*@30mA.
MIL-STD-750D:1026
MIL-STD-883D:1005
JIS C 7021:B-1
High Temperature
High Humidity
Storage
Ta= 65±5℃,RH= 90~95%
*Test Time= 240HRS±2HRS
MIL-STD-202F:103B
JIS C 7021:B-11
High Temperature
Storage
Ta= 105±5℃
*Test Time= 1000HRS (-24HRS,+72HRS)
MIL-STD-883D:1008
JIS C 7021:B-10
Low Temperature
Storage
Ta= -55±5℃
*Test Time=1000HRS (-24HRS,+72H RS)
JIS C 7021:B-12
105℃ ~ 25℃ ~ -55℃ ~ 25℃
30mins 5mins
30mins 5mins
10 Cycles
MIL-STD-202F:107D
MIL-STD-750D:1051
MIL-STD-883D:1010
JIS C 7021:A-4
85 ± 5℃ ~ -40℃ ± 5℃
10mins
10mins 100 Cycles
MIL-STD-202F:107D
MIL-STD-750D:1051
MIL-STD-883D:1011
Ramp-up rate(217℃ to Peak) +3℃/ second max
Temp. maintain at 175(±25)℃ 180 seconds max
Temp. maintain above 217℃ 60-150 seconds
Peak temperature range 260℃+0/-5℃
Time within 5°C of actual Peak Temperature (tp)
20-40 seconds
Ramp-down rate +6℃/second max
MIL-STD-750D:2031.2
J-STD-020B
Operation Life
Endurance
Test
Temperature
Cycling
Thermal
Shock
Environmental
Test
IR-Reflow
Solderability
Part No. : LTW-E670DS-STE
BNS-OD-C131/A4
MIL-STD-202F:208D
MIL-STD-750D:2026
MIL-STD-883D:2003
IEC 68 Part 2-20
JIS C 7021:A-2
T.sol= 245 ± 5℃
Immersion time 3±0.5 sec
Immersion rate 25±2.5 mm/sec
Coverage ≧95% of the dipped surface
Page :
10
of
11
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
8. Others
The appearance and specifications of the product may be modified for improvement without prior notice.
9. Suggested Checking List
Training and Certification
1. Everyone working in a static-safe area is ESD-certified?
2. Training records kept and re-certification dates monitored?
Static-Safe Workstation & Work Areas
1. Static-safe workstation or work-areas have ESD signs?
2. All surfaces and objects at all static-safe workstation and within 1 ft measure less than 100V?
3. All ionizer activated, positioned towards the units?
4. Each work surface mats grounding is good?
Personnel Grounding
1. Every person (including visitors) handling ESD sensitive (ESDS) items wear wrist strap, heel strap or
conductive shoes with conductive flooring?
2. If conductive footwear used, conductive flooring also present where operator stand or walk?
3. Garments, hairs or anything closer than 1 ft to ESD items measure less than 100V*?
4. Every wrist strap or heel strap/conductive shoes checked daily and result recorded for all DLs?
5. All wrist strap or heel strap checkers calibration up to date?
Note: *50V for Blue LED.
Device Handling
1. Every ESDS items identified by EIA-471 labels on item or packaging?
2. All ESDS items completely inside properly closed static-shielding containers when not at static-safe
workstation?
3. No static charge generators (e.g. plastics) inside shielding containers with ESDS items?
4. All flexible conductive and dissipative package materials inspected before reuse or recycle?
Others
1. Audit result reported to entity ESD control coordinator?
2. Corrective action from previous audits completed?
3. Are audit records complete and on file?
Part No. : LTW-E670DS-STE
BNS-OD-C131/A4
Page :
11
of
11