MARVELL 88F6192-XX

Cover
88F6190 and 88F6192
Integrated Controller
Hardware Specifications
Doc. No. MV-S104987-U0, Rev. F
December 2, 2008, Preliminary
L
Marvell. Moving Forward Faster
Document Classification: Proprietary Information
88F619x
Hardware Specifications
Document Conventions
Note: Provides related information or information of special importance.
Caution: Indicates potential damage to hardware or software, or loss of data.
Warning: Indicates a risk of personal injury.
Document Status
Doc Status: Preliminary
Technical Publication: 0.xx
For more information, visit our website at: www.marvell.com
Disclaimer
No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, for any purpose,
without the express written permission of Marvell. Marvell retains the right to make changes to this document at any time, without notice. Marvell makes no warranty of any
kind, expressed or implied, with regard to any information contained in this document, including, but not limited to, the implied warranties of merchantability or fitness for any
particular purpose. Further, Marvell does not warrant the accuracy or completeness of the information, text, graphics, or other items contained within this document.
Marvell products are not designed for use in life-support equipment or applications that would cause a life-threatening situation if any such products failed. Do not use
Marvell products in these types of equipment or applications.
With respect to the products described herein, the user or recipient, in the absence of appropriate U.S. government authorization, agrees:
1) Not to re-export or release any such information consisting of technology, software or source code controlled for national security reasons by the U.S. Export Control
Regulations ("EAR"), to a national of EAR Country Groups D:1 or E:2;
2) Not to export the direct product of such technology or such software, to EAR Country Groups D:1 or E:2, if such technology or software and direct products thereof are
controlled for national security reasons by the EAR; and,
3) In the case of technology controlled for national security reasons under the EAR where the direct product of the technology is a complete plant or component of a plant,
not to export to EAR Country Groups D:1 or E:2 the direct product of the plant or major component thereof, if such direct product is controlled for national security reasons
by the EAR, or is subject to controls under the U.S. Munitions List ("USML").
At all times hereunder, the recipient of any such information agrees that they shall be deemed to have manually signed this document in connection with their receipt of any
such information.
Copyright © 2008. Marvell International Ltd. All rights reserved. Marvell, the Marvell logo, Moving Forward Faster, Alaska, Fastwriter, Datacom Systems on Silicon, Libertas,
Link Street, NetGX, PHYAdvantage, Prestera, Raising The Technology Bar, The Technology Within, Virtual Cable Tester, and Yukon are registered trademarks of Marvell.
Ants, AnyVoltage, Discovery, DSP Switcher, Feroceon, GalNet, GalTis, Horizon, Marvell Makes It All Possible, RADLAN, UniMAC, and VCT are trademarks of Marvell. All
other trademarks are the property of their respective owners.
Doc. No. MV-S104987-U0 Rev. F
Page 2
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
88F6190 and 88F6192
Integrated Controller
Hardware Specifications
PRODUCT OVERVIEW
The Marvell® 88F6190 and 88F6192 are high-performance, highly integrated controllers. These controllers are based
on the Marvell proprietary, ARMv5TE-compliant, high-speed Sheeva™ CPU core. The CPU core integrates a 256 KB
L2 cache.
Processor
Sheeva™ CPU Core
JTAG interface
16 KB-I, 16 KB-D cache
Up to 600 MHz
L2
cache
256 KB
High Speed I/0
PCI Express
Memory
SATA
DDR
SDRAM
controller
USB 2.0
Security Engine
AES/DES/
3DES
SHA-1/MD5
XOR Engine
Internal bus
External DDR
400 MHz
PCI Express x1
SATA port
USB 2.0 port
Gigabit Ethernet
IEEE 1588AVB support
Gigabit Ethernet
4 XOR/DMA channels
Fast Ethernet
UART x2
GPIO, TWSI
SPI, NAND, SDIO
Slow bus
Misc
Flash, SDIO
88F6190 Functional Block Diagram
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 3
88F619x
Hardware Specifications
Processor
High Speed I/0
Sheeva™ CPU Core
JTAG interface
16 KB-I, 16 KB-D cache
Up to 800 M Hz
L2
cache
256 KB
PCI Express
SATA
Mem ory
USB 2.0
PCI Express x1
Dual SATA ports
USB 2.0 port
DDR
SDRAM
controller
External DDR
400 MHz
M edia interfaces
Security Engine
AES/DES/
3DES
MPEG TS
M PEG2-TS
Audio
I 2 S / S/PDIF
SHA-1/MD5
XO R Engine
4 XOR/DM A channels
G igabit Ethernet
IEEE 1588AVB support
Misc
TDM
UART x2
GPIO, TW SI
SPI, NAND, SDIO
Slow bus
FXS / FXO
GbE
GbE
Flash, SDIO
88F6192 Functional Block Diagram
Doc. No. MV-S104987-U0 Rev. F
Page 4
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Features
FEATURES
• Branch Prediction unit
• Supports JTAG/ARM ICE
• Supports both Big and Little Endian modes
88F6190 – Incorporates a single GbE port and a single
SATA port. CPU speed is up to 600 MHz.
88F6192 – Incorporates two GbE ports and two SATA
ports. CPU speed is up to 800 MHz. It also supports a
Sony/Philips Digital Interconnect Format / Integrated
Interchip Sound (S/PDIF / I2S) Audio interface, a TDM
SLIC/SLAC Codec interface, and an MPEG Transport
Stream (TS) interface.
„
The 88F6190 and 88F6192 controllers include:
• High-performance CPU core, running at up to
600 MHz in the 88F6190 or 800 MHz in the
88F6192, with integrated, four-way, set-associative
L1 16-KB I-cache/16-KB D-cache and unified,
256-KB, four-way, set-associative L2 cache
• High-bandwidth dual-port DDR2 memory interface
(16-bit DDR2 SDRAM @ up to 400 MHz data rate)
• PCI Express (x1) port with integrated PHY
• Gigabit Ethernet (10/100/1000 Mbps) MAC(s)
• USB 2.0 port with integrated PHY
• SATA 2.0 port(s) with integrated 3 Gbps SATA II PHY
• Security Cryptographic engine
S/PDIF / I2S Audio in/out interface (88F6192 only)
SD/SDIO/MMC interface
TDM SLIC/SLAC Codec interface (88F6192 only)
Two XOR engines, each containing two XOR/DMA
channels (a total of four XOR/DMA channels)
• MPEG Transport Stream (TS) interface
(88F6192 only)
• SPI port with SPI flash boot support
• 8-bit NAND flash interface with boot support
• Two 16550 compatible UART interfaces
• TWSI port
• 36 multi-purpose pins
• Internal Real Time Clock (RTC)
• Interrupt controller
• Timers
• 128-bit eFuse (one-time programmable memory)
Sheeva™ CPU core
• 88F6190 – Up to 600 MHz
• 88F6192 – Up to 800 MHz
• 32-bit and 16-bit RISC architecture
• Compliant with v5TE architecture, as published in
the ARM Architect Reference Manual, Second
Edition
• Includes MMU to support virtual memory features
• 256-KB, four-way, set-associative L2 unified cache
• 16-KB, four-way, set-associative I-cache
• 16-KB, four-way, set-associative D-cache
• 64-bit internal data bus
•
•
•
•
„
„
„
„
„
DDR2 SDRAM controller
• 16-bit interface
• Up to 200 MHz clock frequency (400 MHz data rate)
• DDR SDRAM with a clock ratio of 1:N and 2:N
between the DDR SDRAM and the CPU core,
respectively
• SSTL 1.8V I/Os
• Auto calibration of I/Os output impedance
• Supports two DRAM chip selects
• Supports all DDR devices densities up to1 Gb
• Supports up to16 open pages (page per bank)
• Up to 512 MB total address space
• Supports on-board DDR designs (no DIMM support)
• Supports 2T mode, to enable high-frequency
operation under heavy load configuration
• Supports DRAM bank interleaving
• Supports up to a 128-byte burst per single memory
access
PCI Express interface (x1)
• PCI Express Base 1.1 compatible
• Integrated low-power SERDES PHY, based on
proven Marvell® SERDES technology
• Serves as a Root Complex or an Endpoint port
• x1 link width
• 2.5 Gbps data rate
• Lane polarity reversal support
• Maximum payload size of 128 bytes
• Single Virtual Channel (VC-0)
• Replay buffer support
• Extended PCI Express configuration space
• Advanced Error Reporting (AER) support
• Power management: L0s and software L1 support
• Interrupt emulation message support
• Error message support
PCI Express master specific features
• Single outstanding read transaction
• Maximum read request of up to 128 bytes
• Maximum write request of up to 128 bytes
• Up to four outstanding read transactions in
Endpoint mode
PCI Express target specific features
• Supports up to eight read request transactions
• Maximum read request size of 4 KB
• Maximum write request of 128 bytes
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 5
88F619x
Hardware Specifications
• Supports PCI Express access to all of the
• Up to four independent endpoints, supporting
controller’s internal registers
„
Integrated GbE (10/100/1000) MAC port(s)
• 88F6190 – One GbE port and one Fast Ethernet
port
• 88F6192 – Two GbE ports
• Supports 10/100/1000 Mbps
• Dedicated DMA for data movement between
memory and port
• Priority queuing on receive based on Destination
Address (DA), VLAN Tag, and IP TOS
• Layer 2/3/4 frame encapsulation detection
• TCP/IP checksum on receive and transmit
• Supports proprietary 200 Mbps Marvell MII (MMII)
interface
• 88F6190 supports the following modes:
- Port 0 RGMII, Port 1 MII/MMII
- Port 0 GMII, Port 1 N/A
• 88F6192 supports the following modes:
- Port 0 RGMII, Port 1 RGMII
- Port 0 RGMII, Port 1 MII/MMII
- Port 0 MII/MMII, Port 1 RGMII
- Port 0 GMII, Port 1 N/A
• DA filtering
„
Precise Timing Protocol (PTP)
• Supports precise time stamping for packets, as
defined in IEEE 1588 PTP v1 and v2 and IEEE
802.1AS draft standards
• Supports Flexible Time Application interface to
distribute PTP clock and time to other devices in
the system
• Optionally accepts an external clock input for time
stamping
„
Audio Video Bridging networks
• Supports IEEE 802.1Qav draft Audio Video
Bridging networks
• Supports time- and priority-aware egress pacing
algorithm to prevent bunching and bursting
effects—suitable for audio/video applications
• Supports Egress Jitter Pacer for AVB-Class A and
AVB-Class B traffic and strict priority for legacy
traffic queues
„
USB 2.0 port
• Serves as a peripheral or host
• USB 2.0 compliant
• Integrated USB 2.0 PHY
• Enhanced Host Controller Interface (EHCI)
compatible as a host
• As a host, supports direct connection to all
peripheral types (LS, FS, HS)
• As a peripheral, connects to all host types (HS, FS)
and hubs
control, interrupt, bulk, and isochronous data
transfers
• Dedicated DMA for data movement between
memory and port
„
Integrated Marvell 3 Gbps (Gen2i) SATA PHYs
• 88F6190 – Single SATA port
• 88F6192 – Two SATA ports
• Compliant with SATA II Phase 1 specifications
- Supports SATA II Native Command Queuing
(NCQ), up to 128 outstanding commands per
port
- Fully supports first party DMA (FPDMA)
- Backwards compatible with SATA I devices
• Supports SATA II Phase 2 advanced features
- 3 Gbps (Gen2i) SATA II speed
- Port Multiplier (PM)—performs FIS-based
switching, as defined in SATA working group PM
definition
- Port Selector (PS)—issues the protocol-based
Out-Of-Band (OOB) sequence, for selecting the
active host port
• Supports device 48-bit addressing
• Supports ATA Tag Command Queuing
„
SATA II Host controller
• Enhanced-DMA (EDMA) for the SATA ports
• Automatic command execution, without host
intervention
• Command queuing support, for up to 32
outstanding commands
• Separate SATA request/response queues
• 64-bit addressing support for descriptors and data
buffers in system memory
• Read ahead
• Advanced interrupt coalescing
• Target mode operation—supports attaching two
88F6190/88F6192 controllers through their
Serial-ATA ports, enabling data communication
between the 88F6190/88F6192 controllers
• Advanced drive diagnostics via the ATA SMART
command
„
Cryptographic engine
• Hardware implementation on encryption and
authentication engines, to boost packet processing
speed
• Dedicated DMA to feed the hardware engines with
data from the internal SRAM memory or from the
DDR memory
• Implements AES, DES, and 3DES encryption
algorithms
• Implements SHA1 and MD5 authentication
algorithms
Doc. No. MV-S104987-U0 Rev. F
Page 6
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Features
„
S/PDIF / I2S Audio In/Out interface (88F6192 only)
• Either S/PDIF or I2S inputs can be active at one
time
• Both S/PDIF and I2S outputs can be active
simultaneously, transferring the same PCM data
„
S/PDIF-specific features (88F6192 only)
• Compliant with 60958-1, 60958-3, and IEC61937
specifications
• Sample rates of 44.1/48/96 kHz
• 16/20/24-bit depths
„
I2S-specific features (88F6192 only)
• Sample rates of 44.1/48/96 kHz
• I2S input and I2S output operate at the same
„
Serial Peripheral Interface (SPI) controller
• Up to 41.6 MHz clock
• Supports direct boot from external SPI serial flash
memory
„
MPEG Transport Stream (TS) interface (88F6192
only)
• ISO/IEC 13818-1 standard compliant
• Supports any one of the following modes:
- Parallel (8 bit) input
- Parallel output
- Two independent serial interfaces
• Data rate up to 80 Mbps
„
Two UART interfaces
• 16550 UART compatible
• Two pins for transmit and receive operations
• Two pins for modem control functions
„
Two-Wire Serial Interface (TWSI)
• General purpose TWSI master/slave port
• Can also be used for serial ROM initialization
„
36 dedicated Multi-Purpose Pins (MPPS) for
peripheral functions and general purpose I/O
• Each pin can be configured independently.
• GPIO inputs can be used to register interrupts from
external devices, and to generate maskable
interrupts.
• In the 88F6192, one of the following multiplexed
interfaces may be configured at a time:
- Audio
- TS
- TDM
- GbE Port 0 in GMII mode or GbE Port 1
„
Interrupt Controller
Maskable interrupts to CPU core
(and PCI Express for a PCI Express endpoint)
„
Two general purpose 32-bit timers/counters
Internal architecture
• Mbus-L bus for high-performance, low-latency CPU
core to DDR SDRAM connectivity
• Advanced Mbus architecture
• Dual port DDR SDRAM controller connectivity to
both CPU and Mbus
sample rate
• 16/24-bit depths
• I2S in and I2S out support independent bit depths
(16 bit/24 bit)
• Supports plain I2S, right-justified and left-justified
formats
„
SD/SDIO/MMC host interface
• 1-bit/4-bit SDmem, SDIO, and MMC cards
• Up to 50 MHz
• Hardware generate/check CRC, on all command
and data transactions on the card bus
„
TDM SLIC/SLAC Codec interface (88F6192 only)
• Generic interface to standard SLIC/SLAC codec
devices
• Compatible with standard PCM highway formats
• TDM protocol support for two channels, up to
128 time slots
• Dedicated SPI interface for codec management
• Integrated DMA to transfer voice data to/from
memory buffer
„
„
Two XOR engines and DMA
• Two XOR/DMA channels per XOR engine (for a
total of four XOR/DMA channels)
• Chaining via linked-lists of descriptors
• Moves data from source interface to destination
interface
• Supports increment or hold on both Source and
Destination Addresses
• Supports XOR operation, on up to eight source
blocks—useful for RAID applications
• Supports iSCSI CRC-32 calculation
NAND flash controller
• 8-bit NAND flash interface
• Glueless interface to CE Care and CE Don’t Care
NAND flash devices
• Boot support
„
„
Bootable from
• SPI flash
• SATA device
• NAND flash
• PCI Express
• UART (for debug purpose)
„
216-pin LQFP package, 24 x 24 mm, 0.4 mm pitch
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 7
88F619x
Hardware Specifications
Hard Disk
Drive
PCI Express
Mini Card Wi-Fi
x1
x16
On Board DDR2
88F6190
USB Host
SPI Flash
Gigabit
Ethernet
PHY
88F6190 Usage Model Example: Common NAS Application
SATA Port
Multiplier
Hard Disk
Drive
PCI Express
Mini Card Wi-Fi
x1
x16
On Board DDR2
88F6192
USB Host
SPI Flash
Gigabit
Ethernet
PHY
88F6192 Usage Model Example: Common NAS Application
Doc. No. MV-S104987-U0 Rev. F
Page 8
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Table of Contents
Table of Contents
Product Overview ....................................................................................................................................... 3
Features....................................................................................................................................................... 5
Preface.......................................................................................................................................................16
About this Document .......................................................................................................................................16
Related Documentation...................................................................................................................................16
Document Conventions ...................................................................................................................................17
1
Overview....................................................................................................................................... 18
2
Pin and Signal Descriptions ....................................................................................................... 20
2.1
Pin Logic .........................................................................................................................................................21
2.2
Pin Descriptions ..............................................................................................................................................23
2.3
Internal Pull-up and Pull-down Pins ................................................................................................................55
3
Unused Interface Strapping........................................................................................................ 56
4
88F6190 Pinout ............................................................................................................................ 57
5
88F6192 Pinout ............................................................................................................................ 59
6
Pin Multiplexing ........................................................................................................................... 61
6.1
Multi-Purpose Pins Functional Summary ........................................................................................................61
6.2
Gigabit Ethernet (GbE) Pins Multiplexing on MPP ..........................................................................................68
6.3
TSMP (TS Multiplexing Pins) on MPP.............................................................................................................70
7
Clocking ....................................................................................................................................... 71
7.1
Spread Spectrum Clock Generator (SSCG)....................................................................................................72
8
System Power Up/Down and Reset Settings ............................................................................ 73
8.1
Power-Up/Down Sequence Requirements......................................................................................................73
8.2
Hardware Reset ..............................................................................................................................................74
8.3
PCI Express Reset ..........................................................................................................................................76
8.4
Sheeva™ CPU TAP Controller Reset..............................................................................................................76
8.5
Pins Sample Configuration..............................................................................................................................76
8.6
Serial ROM Initialization ..................................................................................................................................80
8.7
Boot Sequence................................................................................................................................................81
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 9
88F619x
Hardware Specifications
9
JTAG Interface ............................................................................................................................. 83
9.1
TAP Controller.................................................................................................................................................83
9.2
Instruction Register .........................................................................................................................................83
9.3
Bypass Register ..............................................................................................................................................84
9.4
JTAG Scan Chain ...........................................................................................................................................84
9.5
ID Register ......................................................................................................................................................84
10
Electrical Specifications (Preliminary) ......................................................................................85
10.1
Absolute Maximum Ratings ............................................................................................................................85
10.2
Recommended Operating Conditions .............................................................................................................87
10.3
Thermal Power Dissipation .............................................................................................................................89
10.4
Current Consumption ......................................................................................................................................91
10.5
DC Electrical Specifications ............................................................................................................................92
10.6
AC Electrical Specifications ............................................................................................................................97
10.7
Differential Interface Electrical Characteristics..............................................................................................127
11
Thermal Data (Preliminary) .......................................................................................................138
12
Package ......................................................................................................................................139
13
Part Order Numbering/Package Marking ................................................................................141
13.1
Part Order Numbering ...................................................................................................................................141
13.2
Package Marking ..........................................................................................................................................142
A
Revision History ........................................................................................................................143
Doc. No. MV-S104987-U0 Rev. F
Page 10
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
List of Tables
List of Tables
1
Overview............................................................................................................................................ 18
Table 1:
2
3
Pin and Signal Descriptions ............................................................................................................ 20
Table 2:
Pin Functions and Assignments Table Key ......................................................................................23
Table 3:
Interface Pin Prefix Codes ................................................................................................................23
Table 4:
Power Pin Assignments ....................................................................................................................25
Table 5:
Miscellaneous Pin Assignments .......................................................................................................27
Table 6:
DDR SDRAM Interface Pin Assignments .........................................................................................28
Table 7:
PCI Express Interface Pin Assignments ...........................................................................................30
Table 8:
SATA Port Interface Pin Assignment ................................................................................................31
Table 9:
88F6190 Gigabit Ethernet Interface Pin Assignments .....................................................................32
Table 10:
88F6192 Gigabit Ethernet Port0/1 Interface Pin Assignments ........................................................34
Table 11:
Serial Management Interface (SMI) Pin Assignments ......................................................................39
Table 12:
USB 2.0 Interface Pin Assignments..................................................................................................40
Table 13:
JTAG Pin Assignment.......................................................................................................................41
Table 14:
RTC Interface Pin Assignments........................................................................................................42
Table 15:
NAND Flash Interface Pin Assignment .............................................................................................43
Table 16:
MPP Interface Pin Assignment .........................................................................................................44
Table 17:
Two-Wire Serial Interface (TWSI) Interface Pin Assignment ............................................................45
Table 18:
UART Port 0/1 Interface Pin Assignment .........................................................................................46
Table 19:
Audio (S/PDIF / I2S) Interface Signal Assignment ............................................................................47
Table 20:
Serial Peripheral Interface (SPI) Interface Signal Assignment .........................................................48
Table 21:
Secure Digital Input/Output (SDIO) Interface Signal Assignment.....................................................49
Table 22:
Time Division Multiplexing (TDM) Interface Signal Assignment .......................................................50
Table 23:
Transport Stream (TS) Interface Signal Assignment ........................................................................52
Table 24:
Precise Timing Protocol (PTP) Interface Signal Assignment............................................................54
Table 25:
Internal Pull-up and Pull-down Pins ..................................................................................................55
Unused Interface Strapping............................................................................................................. 56
Table 26:
4
88F6190 Pinout Sorted by Pin Number ............................................................................................58
88F6192 Pinout ................................................................................................................................. 59
Table 28:
6
Unused Interface Strapping ..............................................................................................................56
88F6190 Pinout ................................................................................................................................. 57
Table 27:
5
88F6190 and 88F6192 Device Differences ......................................................................................18
88F6192 Pinout Sorted by Pin Number ............................................................................................60
Pin Multiplexing ................................................................................................................................ 61
Table 29:
MPP Functionality .............................................................................................................................62
Table 30:
88F6190 MPP Function Summary....................................................................................................63
Table 31:
88F6192 MPP Function Summary....................................................................................................65
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 11
88F619x
Hardware Specifications
7
8
9
10
Table 32:
88F6190 Ethernet Ports Pins Multiplexing........................................................................................68
Table 33:
88F6192 Ethernet Ports Pins Multiplexing........................................................................................69
Table 34:
TS Port Pin Multiplexing .................................................................................................................70
Clocking............................................................................................................................................. 71
Table 35:
88F619x Clocks ................................................................................................................................71
Table 36:
Supported Clock Combinations ........................................................................................................72
System Power Up/Down and Reset Settings ................................................................................. 73
Table 37:
I/O and Core Voltages ......................................................................................................................73
Table 38:
Reset Configuration ..........................................................................................................................77
JTAG Interface .................................................................................................................................. 83
Table 39:
Supported JTAG Instructions............................................................................................................83
Table 40:
IDCODE Register Map .....................................................................................................................84
Electrical Specifications (Preliminary) ........................................................................................... 85
Table 41:
Absolute Maximum Ratings ..............................................................................................................85
Table 42:
Recommended Operating Conditions...............................................................................................87
Table 43:
Thermal Power Dissipation ...............................................................................................................89
Table 44:
Current Consumption........................................................................................................................91
Table 45:
General 3.3V Interface (CMOS) DC Electrical Specifications...........................................................92
Table 46:
RGMII 1.8V Interface (CMOS) DC Electrical Specifications .............................................................93
Table 47:
SDRAM DDR2 Interface DC Electrical Specifications ......................................................................94
Table 48:
TWSI Interface 3.3V DC Electrical Specifications.............................................................................95
Table 49:
SPI Interface 3.3V DC Electrical Specifications................................................................................95
Table 50:
TDM Interface 3.3V DC Electrical Specifications..............................................................................96
Table 51:
Reference Clock AC Timing Specifications ......................................................................................97
Table 52:
SDRAM DDR2 Interface AC Timing Table .......................................................................................99
Table 53:
RGMII 10/100/1000 AC Timing Table at 1.8V ................................................................................102
Table 54:
RGMII 10/100 AC Timing Table at 3.3V .........................................................................................102
Table 55:
GMII AC Timing Table ....................................................................................................................104
Table 56:
MII/MMII MAC Mode AC Timing Table ...........................................................................................106
Table 57:
SMI Master Mode AC Timing Table................................................................................................108
Table 58:
JTAG Interface AC Timing Table ....................................................................................................110
Table 59:
TWSI Master AC Timing Table .......................................................................................................112
Table 60:
TWSI Slave AC Timing Table .........................................................................................................112
Table 61:
S/PDIF AC Timing Table ................................................................................................................114
Table 62:
Inter-IC Sound (I2S) AC Timing Table ............................................................................................116
Table 63:
TDM Interface AC Timing Table .....................................................................................................118
Table 64:
SPI (Master Mode) AC Timing Table ..............................................................................................120
Table 65:
SDIO Host in High Speed Mode AC Timing Table .........................................................................122
Table 66:
Transport Stream Output Interface AC Timing Table ....................................................................124
Table 67:
Transport Stream Input Interface AC Timing Table ........................................................................124
Table 68:
PCI Express Interface Differential Reference Clock Characteristics ..............................................127
Table 69:
PCI Express Interface Spread Spectrum Requirements.................................................................128
Doc. No. MV-S104987-U0 Rev. F
Page 12
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
List of Tables
11
Table 70:
PCI Express Interface Driver and Receiver Characteristics ...........................................................129
Table 71:
SATA-I Interface Gen1i Mode Driver and Receiver Characteristics ...............................................132
Table 72:
SATA-II Interface Gen2i Mode Driver and Receiver Characteristics ..............................................133
Table 73:
USB Low Speed Driver and Receiver Characteristics ....................................................................134
Table 74:
USB Full Speed Driver and Receiver Characteristics.....................................................................135
Table 75:
USB High Speed Driver and Receiver Characteristics ...................................................................136
Thermal Data (Preliminary) ............................................................................................................138
Table 76:
12
13
Package ...........................................................................................................................................139
Table 77:
LQFP 216-pin Package Dimensions...............................................................................................140
Table 78:
LQFP 216-pin Package Exposed Pad (ePAD) Size .......................................................................140
Part Order Numbering/Package Marking......................................................................................141
Table 79:
A
Thermal Data for the 88F619x in the QFP 216-pin Package (Preliminary) ....................................138
Part Order Options..........................................................................................................................141
Revision History .............................................................................................................................143
Table 80:
Revision History ..............................................................................................................................143
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 13
88F619x
Hardware Specifications
List of Figures
1
Overview........................................................................................................................................... 18
2
Pin and Signal Descriptions ........................................................................................................... 20
Figure 1:
88F6190 Pin Logic Diagram .............................................................................................................21
Figure 2:
88F6192 Pin Logic Diagram .............................................................................................................22
3
Unused Interface Strapping............................................................................................................ 56
4
88F6190 Pinout ................................................................................................................................ 57
Figure 3:
5
88F6190 Pin Map Top View .............................................................................................................57
88F6192 Pinout ................................................................................................................................ 59
Figure 4:
88F6192 Pin Map Top View .............................................................................................................59
6
Pin Multiplexing ............................................................................................................................... 61
7
Clocking............................................................................................................................................ 71
8
System Power Up/Down and Reset Settings ................................................................................ 73
9
10
Figure 5:
Power-Up Sequence Example..........................................................................................................74
Figure 6:
Serial ROM Data Structure ...............................................................................................................80
Figure 7:
Serial ROM Read Example...............................................................................................................81
JTAG Interface ................................................................................................................................. 83
Electrical Specifications (Preliminary) .......................................................................................... 85
Figure 8:
SDRAM DDR2 Interface Test Circuit ..............................................................................................100
Figure 9:
SDRAM DDR2 Interface Write AC Timing Diagram .......................................................................100
Figure 10:
SDRAM DDR2 Interface Address and Control AC Timing Diagram ...............................................101
Figure 11:
SDRAM DDR2 Interface Read AC Timing Diagram .......................................................................101
Figure 12:
RGMII Test Circuit ..........................................................................................................................103
Figure 13:
RGMII AC Timing Diagram .............................................................................................................103
Figure 14:
GMII Test Circuit .............................................................................................................................104
Figure 15:
GMII Output AC Timing Diagram ....................................................................................................105
Figure 16:
GMII Input AC Timing Diagram.......................................................................................................105
Figure 17:
MII/MMII MAC Mode Test Circuit....................................................................................................106
Figure 18:
MII/MMII MAC Mode Output Delay AC Timing Diagram.................................................................106
Figure 19:
MII/MMII MAC Mode Input AC Timing Diagram..............................................................................107
Figure 20:
MDIO Master Mode Test Circuit .....................................................................................................108
Figure 21:
MDC Master Mode Test Circuit ......................................................................................................109
Figure 22:
SMI Master Mode Output AC Timing Diagram ...............................................................................109
Figure 23:
SMI Master Mode Input AC Timing Diagram ..................................................................................109
Figure 24:
JTAG Interface Test Circuit ............................................................................................................110
Doc. No. MV-S104987-U0 Rev. F
Page 14
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
List of Figures
11
12
Figure 25:
JTAG Interface Output Delay AC Timing Diagram .........................................................................111
Figure 26:
JTAG Interface Input AC Timing Diagram ......................................................................................111
Figure 27:
TWSI Test Circuit............................................................................................................................113
Figure 28:
TWSI Output Delay AC Timing Diagram.........................................................................................113
Figure 29:
TWSI Input AC Timing Diagram .....................................................................................................113
Figure 30:
S/PDIF Test Circuit .........................................................................................................................115
Figure 31:
Inter-IC Sound (I2S) Test Circuit ....................................................................................................116
Figure 32:
Inter-IC Sound (I2S) Output Delay AC Timing Diagram .................................................................117
Figure 33:
Inter-IC Sound (I2S) Input AC Timing Diagram ..............................................................................117
Figure 34:
TDM Interface Test Circuit ..............................................................................................................119
Figure 35:
TDM Interface Output Delay AC Timing Diagram...........................................................................119
Figure 36:
TDM Interface Input Delay AC Timing Diagram..............................................................................119
Figure 37:
SPI (Master Mode) Test Circuit ......................................................................................................120
Figure 38:
SPI (Master Mode) Output AC Timing Diagram .............................................................................121
Figure 39:
SPI (Master Mode) Input AC Timing Diagram ................................................................................121
Figure 40:
Secure Digital Input/Output (SDIO) Test Circuit .............................................................................122
Figure 41:
SDIO Host in High Speed Mode Output AC Timing Diagram .........................................................123
Figure 42:
SDIO Host in High Speed Mode Input AC Timing Diagram............................................................123
Figure 43:
Transport Stream Interface Test Circuit..........................................................................................125
Figure 44:
Transport Stream Output Interface AC Timing Diagram ................................................................125
Figure 45:
Transport Stream Input Interface AC Timing Diagram ...................................................................126
Figure 46:
PCI Express Interface Test Circuit..................................................................................................130
Figure 47:
Low/Full Speed Data Signal Rise and Fall Time ............................................................................136
Figure 48:
High Speed TX Eye Diagram Pattern Template .............................................................................137
Figure 49:
High Speed RX Eye Diagram Pattern Template.............................................................................137
Thermal Data (Preliminary) ........................................................................................................... 138
Package .......................................................................................................................................... 139
Figure 50:
13
LQFP 216-pin Package and Dimensions........................................................................................139
Part Order Numbering/Package Marking..................................................................................... 141
Figure 51:
Sample Part Number ......................................................................................................................141
Figure 52:
Package Marking and Pin 1 Location .............................................................................................142
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 15
88F619x
Hardware Specifications
Preface
About this Document
This datasheet provides the hardware specifications for the 88F6190 and 88F6192 integrated
controllers. The hardware specifications include detailed pin information, configuration settings,
electrical characteristics and physical specifications.
This datasheet is intended to be the basic source of information for designers of new systems.
All feature descriptions and specifications described in this document refer to both controllers,
unless otherwise specified.
In this document, the 88F6190 and 88F6192 are often referred to as “88F619x“ or “the device(s)”.
Related Documentation
The following documents contain additional information related to the 88F619x:
„
88F6180, 88F6190, 88F6192, and 88F6281 Functional Specifications,
Doc No. MV-S104860-U0
„
Sheeva™ 88SV131 ARM v5TE Processor Core with MMU and L1/L2 Cache Datasheet,
Doc No. MV-S104950-U0
„
Unified Layer 2 (L2) Cache for Sheeva™ CPU Cores Addendum, Doc No. MV-S104858-U0
„
88F6180, 88F6190, 88F6192, and 88F6281 Functional Errata, Interface Guidelines, and
Restrictions, Doc No. MV-S501157-U0
„
88F6180, 88F6190, 88F6192, and 88F6281 Design Guide, Doc No. MV-S301398-001
„
AN-63: Thermal Management for Marvell Technology Products Doc No. MV-S300281-001
„
AN-179: TWSI Software Guidelines for Discovery™, Horizon™, and Feroceon® Devices,
Doc No. MV-S300754-001
„
AN-183: 88F5181 and 88F5281 Big Endian and Little Endian Support,
Doc No. MV-S300767-001
„
AN-249: Configuring the Marvell® SATA PHY to Transmit Predefined Test Patterns,
Doc No. MV-S301342-001
„
AN-260 System Power-Saving Methods for 88F6180, 88F6190, 88F6192, and 88F6281,
Doc No. MV-S301454-001
„
TB-227: Differences Between the 88F6190, 88F6192, and 88F6281 Stepping Z0 and A0,
Doc No. MV-S105223-001
„
White Paper, ThetaJC, ThetaJA, and Temperature Calculations, Doc No. MV-S700019-00
„
ARM Architecture Reference Manual, Second Edition
„
PCI Express Base Specification, Revision 1.1
„
Universal Serial Bus Specification, Revision 2.0, April 2000, Compaq, Hewlett-Packard, Intel,
Lucent, Microsoft, NEC, Philips
„
Enhanced Host Controller Interface Specification for Universal Serial Bus, Revision 0.95,
November 2000, Intel Corporation
„
ARC USB-HS OTG High-Speed Controller Core reference V 4.0.1
„
Federal Information Processing Standards (FIPS) 46-2 (Data Encryption Standard)
1. This document is a Marvell proprietary, confidential document, requiring an NDA and can be downloaded from the
Marvell Extranet.
Doc. No. MV-S104987-U0 Rev. F
Page 16
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Preface
Document Conventions
„
„
„
„
„
„
„
„
„
FIPS 81 (DES Modes of Operation)
FIPS 180-1 (Secure Hash Standard)
FIPS draft - Advanced Encryption Standard (Rijndeal)
RFC 1321 (The MD5 Message-Digest Algorithm)
RFC 1851 – The ESP Triple DES Transform
RFC 2104 (HMAC: Keyed-Hashing for Message Authentication).
RFC 2405 – The ESP DES-CBC Cipher Algorithm With Explicit IV
IEEE standard, 802.3-2000 Clause 14
ANSI standard X3.263-1995
See the Marvell Extranet website for the latest product documentation.
Document Conventions
The following conventions are used in this document:
Signal Range
A signal name followed by a range enclosed in brackets represents a range of logically related
signals. The first number in the range indicates the most significant bit (MSb) and the last
number indicates the least significant bit (LSb).
Example: DB_Addr[12:0]
Active Low Signals #
An n letter at the end of a signal name indicates that the signal’s active state occurs when
voltage is low.
Example: INTn
State Names
State names are indicated in italic font.
Example: linkfail
Register Naming
Conventions
Register field names are indicated by angle brackets.
Example: <RegInit>
Register field bits are enclosed in brackets.
Example: Field [1:0]
Register addresses are represented in hexadecimal format.
Example: 0x0
Reserved: The contents of the register are reserved for internal use only or for future use.
A lowercase <n> in angle brackets in a register indicates that there are multiple registers with
this name.
Example: Multicast Configuration Register<n>
Reset Values
Reset values have the following meanings:
0 = Bit clear
1 = Bit set
Abbreviations
Kb: kilobit
KB: kilobyte
Mb: megabit
MB: megabyte
Gb: gigabit
GB: gigabyte
Numbering Conventions
Unless otherwise indicated, all numbers in this document are decimal (base 10).
An 0x prefix indicates a hexadecimal number.
An 0b prefix indicates a binary number.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 17
88F619x
Hardware Specifications
1
Overview
The Marvell® 88F6190 and 88F6192 devices are high-performance, highly integrated controllers.
The devices are based on the ARMv5TE-compliant, high-speed Sheeva™ 88SV131 CPU core with
256 KB L2 cache.
Table 1 provides a list of the differences between the 88F6190 and 88F6192 devices.
Table 1:
88F6190 and 88F6192 Device Differences
88 F 6 1 9 0
88F6192
Running at up to 600 MHz
L2 cache at up to 300 MHz
Running at up to 800 MHz
L2 cache at up to 400 MHz
Time Division
Multiplexing
(SLIC/codec) Interface
No
Yes1
Serial ATA II (SATA II)
Interface
1 port
2 ports
Gigabit Ethernet
Interface
2 Ethernet ports
• Port0 RGMII, Port1 MII/MMII
• Port0 GMII, Port1 N/A
2 Ethernet ports1
• Port0 RGMII, Port1 RGMII
• Port0 RGMII, Port1 MII/MMII
• Port0 MII/MMII, Port1 RGMII
• Port0 GMII, Port1 N/A
Audio S/PDIF / I2S
Interface
No
Yes1
MPEG Video / Transport
Stream Interface (TS)
No
Yes1
Sheeva
™
CPU Core
DDR SDRAM Interface
•
•
•
•
•
Up to 200 MHz clock frequency with an 400 MHz data rate
Supports two DRAM chip selects
Supports all DDR devices densities up to 1Gb
Supports up to 16 open pages (page per bank)
Up to 512 MB total address space
PCI Express Interface
Yes
USB 2.0 Interface
Yes
Cryptographic Engine
and Security
Accelerator
Yes
XOR engine and DMA
Yes
Two-Wire Serial
Interface (TWSI)
1 port
UART Interface
2 ports
NAND Flash Interface
Yes
SPI Serial Flash
Interface
Yes
SDIO Interface
Yes
Doc. No. MV-S104987-U0 Rev. F
Page 18
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Overview
Table 1:
88F6190 and 88F6192 Device Differences (Continued)
88 F 6 1 9 0
General-Purpose I/O
Port
Real-Time Clock (RTC)
88F6192
36-bits
Yes
1. The following interfaces are multiplexed and only one of them may be selected at a time:
- Audio
- TS
- TDM
- GbE Port 0 in GMII mode
- GbE Port 1
For further details, see Section 6, Pin Multiplexing, on page 61.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 19
88F619x
Hardware Specifications
2
Pin and Signal Descriptions
This section provides a detailed description of the 88F6190 and 88F6192 device pin assignments
and their functionality.
Doc. No. MV-S104987-U0 Rev. F
Page 20
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Pin and Signal Descriptions
Pin Logic
2.1
Pin Logic
Figure 1: 88F6190 Pin Logic Diagram
REF_CLK_XIN
VDD
VDDO
VDD_GE_A
VDD_GE_B
VDD_M
VSS
Misc.
CPU_PLL_AVDD
CORE_PLL_AVDD
XTAL_AVDD
XTAL_AVSS
PEX_AVDD
SATA_AVDD
Power
PCI Express
XOUT
SYSRSTn
TP
ISET
NC
PEX_CLK_P
PEX_CLK_N
PEX_TX_P
PEX_TX_N
PEX_RX_P
PEX_RX_N
PEX_ISET
USB_AVDD
RTC_AVDD
SSCG_AVDD
VHV
MPP[35:0]
USB
MPP
USB_DM
GE_TXCLKOUT
GE_TXD[3:0]
NF_CLE
NF_ALE
NF_CEn
NF_REn
USB_DP
NAND
Flash
Gigabit Ethernet
GE_TXCTL
GE_RXD[3:0]
GE_RXCTL
GE_RXCLK
NF_WEn
GE_MDC
GE_MDIO
JT_CLK
JT_TDI
JT_TDO
JT_TMS_CPU
M_CLKOUT
M_CLKOUTn
M_CKE
JTAG
M_RASn
JT_TMS_CORE
JT_RSTn
SATA_T_P
SATA_T_N
M_CASn
M_WEn
SATA
SDRAM
SATA_R_P
SATA_R_N
RTC_XIN
RTC_XOUT
M_DQ[15:0]
M_DQS[1:0]
M_DQSn[1:0]
M_DM[1:0]
M_ODT
M_STARTBURST
RTC
M_STARTBURST_IN
M_PCAL
M_NCAL
Copyright © 2008 Marvell
December 2, 2008, Preliminary
M_A[13:0]
M_BA[2:0]
M_CSn[1:0]
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 21
88F619x
Hardware Specifications
Figure 2: 88F6192 Pin Logic Diagram
VDD
REF_CLK_XIN
VDDO
VDD_GE_A
VDD_GE_B
Misc.
VDD_M
VSS
CPU_PLL_AVDD
CORE_PLL_AVDD
XTAL_AVDD
XTAL_AVSS
Power
PCI Express
PEX_AVDD
SATA0_AVDD
SATA1_AVDD
XOUT
SYSRSTn
TP
ISET
PEX_CLK_P
PEX_CLK_N
PEX_TX_P
PEX_TX_N
PEX_RX_P
PEX_RX_N
PEX_ISET
USB_AVDD
RTC_AVDD
SSCG_AVDD
VHV
USB
MPP[35:0]
USB_DP
USB_DM
MPP
GE_TXCLKOUT
GE_TXD[3:0]
NF_CLE
NF_ALE
NAND
Flash
NF_CEn
NF_REn
NF_WEn
Gigabit Ethernet
GE_TXCTL
GE_RXD[3:0]
GE_RXCTL
GE_RXCLK
GE_MDC
GE_MDIO
JT_CLK
JT_TDI
JT_TDO
JT_TMS_CPU
JT_TMS_CORE
JT_RSTn
M_CLKOUT
M_CLKOUTn
M_CKE
JTAG
M_RASn
M_CASn
M_WEn
SATA0_T_P
SATA0_T_N
SDRAM
SATA0_R_P
SATA0_R_N
SATA0/1
SATA1_T_P
M_A[13:0]
M_BA[2:0]
M_CSn[1:0]
M_DQ[15:0]
M_DQS[1:0]
M_DQSn[1:0]
M_DM[1:0]
M_ODT
M_STARTBURST
SATA1_T_N
SATA1_R_P
SATA1_R_N
RTC_XIN
M_STARTBURST_IN
M_PCAL
M_NCAL
RTC
RTC_XOUT
NOTE: The GE_TXCLKOUT pin is an input only when used as the MII/MMII Transmit Clock (88F6192
only).
Doc. No. MV-S104987-U0 Rev. F
Page 22
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Pin and Signal Descriptions
Pin Descriptions
For details about MPP configuration options see Section 6.1, Multi-Purpose Pins Functional
Summary, on page 61.
2.2
Pin Descriptions
This section details all the pins for the different interfaces providing a functional description of each
pin and pin attributes.
Table 2<Default ¬¹ Font> defines the abbreviations and acronyms used in the pin description tables.
Table 2:
Pin Functions and Assignments Table Key
Te r m
D e fi n it io n
[n]
n - Represents the SERDES pair number
<n>
Represents port number when there are more than one ports
Analog
Analog Driver/Receiver or Power Supply
Calib
Calibration pad type
CML
Common Mode Logic
CMOS
Complementary Metal-Oxide-Semiconductor
DDR
Double Data Rate
GND
Ground Supply
HCSL
High-speed Current Steering Logic
I
Input
I/O
Input/Output
O
Output
o/d
Open Drain pin
The pin allows multiple drivers simultaneously (wire-OR connection).
A pullup is required to sustain the inactive value.
Power
VDD Power Supply
SSTL
Stub Series Terminated Logic for 1.8V
t/s
Tri-State pin
XXXn
n - Suffix represents an Active Low Signal
Table 3:
Interface Pin Prefix Codes
In t e r f a c e
P re fi x
Misc
N/A
DDR SDRAM
M_
PCI Express
PEX_
SATA
88F6190– SATA_
88F6192 – SATA0_, SATA1_
Gigabit Ethernet
GE_
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 23
88F619x
Hardware Specifications
Table 3:
Interface Pin Prefix Codes (Continued)
In t e r f a c e
P re fi x
USB 2.0
USB_
JTAG
JT_
RTC
RTC_
NAND Flash
NF_
MPP
N/A
TWSI
TW_
UART
UA0_
UA1_
Audio
AU_
SPI
SPI_
SDIO
SD_
TDM
TDM_
PTP
PTP_
Doc. No. MV-S104987-U0 Rev. F
Page 24
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Pin and Signal Descriptions
Pin Descriptions
2.2.1
Power Supply Pins
Table 4 provides the voltage levels for the various interface pins. These do not include the analog
power supplies for the PLLs or PHYs which are explicitly mentioned in the other pin description
tables.
Table 4:
Power Pin Assignments
Pin Name
I /O
Pi n
Ty p e
D es c r ip t i o n
VDD
I
Power
1.0V Digital core and CPU voltage
VDDO
I
Power
3.3V I/O power for MPP[19:0] and JTAG pins
For the 88F6190 –
VDD_GE_A
I
Power
1.8 or 3.3V I/O supply voltage for RGMII and SMI interfaces
3.3V I/O supply voltage for GMII and SMI interfaces
3.3V I/O supply voltage for SMI interface when operating in MII/MMII
mode.
NOTE: When configure to RGMII mode at 3.3V, only 10/100 Mbps
operation is supported.
For the 88F6190 –
VDD_GE_B
I
Power
3.3V I/O supply voltage for GMII and MII/MMII interfaces.
3.3V I/O supply voltage for MPP[35:20].
For the 88F6192 –
VDD_GE_A
I
Power
1.8V or 3.3V I/O supply voltage for RGMII and SMI interfaces
3.3V I/O supply voltage for GMII, MII/MMII, and SMI interfaces
NOTE: When configure to RGMII mode at 3.3V, only 10/100 Mbps
operation is supported.
For the 88F6192 –
VDD_GE_B
I
Power
I/O power for MPP[35:20]
1.8V or 3.3V I/O supply voltage for RGMII interfaces
3.3V I/O supply voltage for GMII and MII/MMII interfaces
NOTE: When configure to RGMII mode at 3.3V, only 10/100 Mbps
operation is supported.
VDD_M
I
Power
1.8V I/O supply voltage for the DDR2 SDRAM interface
VSS
I
GND
VSS
CPU_PLL_AVDD
I
Power
1.8V analog quiet power to CPU PLL
NOTE: See the 88F6180, 88F6190, 88F6192, and 88F6281 Design
Guide for power supply filtering recommendations.
CORE_PLL_AVDD
I
Power
1.8V analog quiet power to Core PLL
NOTE: See the 88F6180, 88F6190, 88F6192, and 88F6281 Design
Guide for power supply filtering recommendations.
SSCG_AVDD
I
Power
1.8V quiet power supply to the internal Spread Spectrum Clock
Generator
XTAL_AVDD
I
Power
1.8V analog quiet power to on-chip clock inverter for supporting external
crystal, and on-chip current reference for SATA and USB PHYs
NOTE: See the 88F6180, 88F6190, 88F6192, and 88F6281 Design
Guide for power supply filtering recommendations.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 25
88F619x
Hardware Specifications
Table 4:
Power Pin Assignments (Continued)
Pin Name
I /O
Pi n
Ty p e
D es c r ip t i o n
VHV
I
Power
I/O supply voltage for eFuse:
• 2.5V for eFuse burning only
• 1.0V for eFuse reading only
PEX_AVDD
I
Power
PCI Express PHY quiet power supply 1.8V
NOTE: See the 88F6180, 88F6190, 88F6192, and 88F6281 Design
Guide for power supply filtering recommendations.
88F6190 –
SATA_AVDD
I
Power
SATA II port quiet 3.3V power supply
NOTE: See 88F6180, 88F6190, 88F6192, and 88F6281 Design Guide
for power supply filtering recommendation.
88F6192–
SATA0_AVDD
SATA1_AVDD
I
Power
SATA II port0/1 quiet 3.3V power supply
NOTE: See 88F6180, 88F6190, 88F6192, and 88F6281 Design Guide
for power supply filtering recommendation.
USB_AVDD
I
Power
USB 2.0 PHY quiet 3.3V power supply
NOTE: See the 88F6180, 88F6190, 88F6192, and 88F6281 Design
Guide for power supply filtering recommendation.
RTC_AVDD
I
Power
1.5V (via battery) or 1.8V (via the board) RTC interface voltage
RTC_AVSS
I
GND
RTC ground
Doc. No. MV-S104987-U0 Rev. F
Page 26
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Pin and Signal Descriptions
Pin Descriptions
2.2.2
Miscellaneous Pin Assignment
The Miscellaneous signal list contains clock and reset, test, and related signals.
Table 5:
Miscellaneous Pin Assignments
Pin Name
I /O
Pi n
Ty pe
P ow e r
Rail
D e s c r i p t io n
REF_CLK_XIN
I
Analog
XTAL_AVDD
Reference clock input from external oscillator or input from
external crystal. Used as input to core, CPU, SATA, and USB
PLLs.
XOUT
O
Analog
XTAL_AVDD
XTAL_OUT
Feedback signal to external crystal.
When not used, leave this pin floating.
SYSRSTn
I
CMOS
VDDO
System reset
Main reset signal of the device clock. Used to reset all units
to their initial state.
When in the reset state, most output pins are in Tri-State.
SYSRST_OUTn
O
CMOS
VDDO
Reset request from the device to the board reset logic.
This pin is multiplexed on the MPP pins (see Section 6, Pin
Multiplexing, on page 61).
PEX_RST_OUTn
O
CMOS
VDDO
Optional PCI Express Endpoint card reset output
This pin is multiplexed on the MPP pins (see Section 6, Pin
Multiplexing, on page 61).
TP
O
Analog
Analog Test Point for SATA, USB, and PCI Express
interfaces
For internal use. Leave this pin unconnected.
ISET
I
Analog
Current reference for both the USB and SATA PHYs.
Terminate this pin with a 6.04 kΩ resistor, pulled down.
NC (88F6190 only)
Reserved for Marvell® future usage.
Leave unconnected externally.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 27
88F619x
Hardware Specifications
2.2.3
Table 6:
DDR SDRAM Interface Pin Assignments
DDR SDRAM Interface Pin Assignments
Pin Name
I /O
Pi n
Ty pe
P ow e r
Rail
D e s cr ip t i o n
M_CLKOUT
M_CLKOUTn
O
SSTL
VDD_M
SDRAM Differential Clock Pair
M_CKE
O
SSTL
VDD_M
Driven high to enable SDRAM clock.
Driven low when setting the SDRAM to Self-refresh mode.
M_RASn
O
SSTL
VDD_M
SDRAM Row Address Select
Asserted to indicate an active ROW address driven on the
SDRAM address lines.
M_CASn
O
SSTL
VDD_M
SDRAM Column Address Select
Asserted to indicate an active column address driven on the
SDRAM address lines.
M_WEn
O
SSTL
VDD_M
SDRAM Write Enable
Asserted to indicate a write command to the SDRAM.
M_A[13:0]
O
SSTL
VDD_M
SDRAM Address
Driven during RASn and CASn cycles to generate—together
with M_BA[2:0]—the SDRAM address.
M_BA[2:0]
O
SSTL
VDD_M
Driven during M_RASn and M_CASn cycles to select one of
the eight SDRAM virtual banks.
NOTE: If an SDRAM device does not support the BA[2] pin,
leave the M_BA[2] unconnected.
M_CSn[1:0]
O
SSTL
VDD_M
SDRAM Chip Selects
Asserted to select a specific SDRAM Physical bank.
M_DQ[15:0]
t/s
I/O
SSTL
VDD_M
SDRAM Data Bus
Driven during write.
Driven by SDRAM during reads.
M_DQS[1:0],
M_DQSn[1:0]
t/s
I/O
SSTL
VDD_M
SDRAM Data Strobe
Driven by the 88F619x during write.
Driven by SDRAM during reads.
M_DM[1:0]
O
SSTL
VDD_M
SDRAM Data Mask
Asserted by the 88F619x to select the specific byte out of the
16-bit data to be written to the SDRAM.
M_ODT
O
SSTL
VDD_M
SDRAM On Die Termination control.
Driven high to connect the SDRAM on die termination.
Driven low to disconnect the SDRAM’s termination.
NOTE: For the recommended setting, refer to the 88F6180,
88F6190, 88F6192, and 88F6281 Design Guide.
Doc. No. MV-S104987-U0 Rev. F
Page 28
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Pin and Signal Descriptions
Pin Descriptions
Table 6:
DDR SDRAM Interface Pin Assignments (Continued)
Pin Name
I /O
Pi n
Ty pe
P ow e r
Rail
D e s cr ip t i o n
M_STARTBURST
O
SSTL
VDD_M
Start Burst
88F619x indication of starting a burst read transaction.
Asserted with the first M_CASn cycle of SDRAM access.
NOTE: Must be routed on board to the SDRAM, and back to
the 88F619x as M_STARTBURST_IN. For the
recommended length calculation for this routing and
termination requirements, see the 88F6180, 88F6190,
88F6192, and 88F6281 Design Guide.
M_START
BURST_IN
I
SSTL
VDD_M
Start Burst Input
M_PCAL
I
Calib
SDRAM interface P channel output driver calibration. Connect
to VSS through a resistor. The resistor value can vary
between 30–70 ohm.
NOTE: See the 88F6180, 88F6190, 88F6192, and 88F6281
Design Guide for the recommended values of the
calibration resistors.
M_NCAL
I
Calib
SDRAM interface N channel output driver calibration. Connect
to M_VDD through a resistor. The resistor value can vary
between 30–70 ohm.
NOTE: See the 88F6180, 88F6190, 88F6192, and 88F6281
Design Guide for the recommended values of the
calibration resistors.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 29
88F619x
Hardware Specifications
2.2.4
Table 7:
PCI Express Interface Pin Assignments
PCI Express Interface Pin Assignments
Pin Name
I/O
P in
Ty p e
Power
R a il
D e s c r i p t io n
PEX_CLK_P/N
I/O
HCSL
PEX_AVDD
PCI Express Reference Clock
100 MHz, differential
This clock can be configured as input or output according to the
reset strap (see Table 38, Reset Configuration, on page 77).
NOTE: For Output mode, 50-ohm, pull-down resistors are
required.
PEX_TX_P/N
O
CML
PEX_AVDD
Transmit Lane
Differential pair of PCI Express transmit data
PEX_RX_P/N
I
CML
PEX_AVDD
Receive Lane
Differential pair of PCI Express receive data
PEX_ISET
I
Analog
Current reference. Pull down to VSS through a 5 kΩ resistor.
See the 88F6180, 88F6190, 88F6192, and 88F6281 Design
Guide for the recommended resistor value.
Doc. No. MV-S104987-U0 Rev. F
Page 30
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Pin and Signal Descriptions
Pin Descriptions
2.2.5
Table 8:
SATA Interface Pin Assignments
SATA Port Interface Pin Assignment
Pin Name
I /O
Pi n
Ty p e
P ow e r R a i l
D e s c r i p t io n
88F6190 – Single SATA Port
SATA_T_P/N
O
CML
SATA_AVDD
Transmit Data: Differential analog output of SATA II port
SATA_R_P/N
I
CML
SATA_AVDD
Receive Data: Differential analog input of SATA II port
SATA_PRESENTn
O
CMOS
VDD_GE_B
When this signal is asserted there is an active link
between the SATA II port and the external device (disk).
NOTE: This signal is multiplexed on the MPP pins (see
Section 6, Pin Multiplexing, on page 61).
SATA_ACTn
O
CMOS
VDD_GE_B
When this signal is asserted, there is an active and used
link between the SATA II port and the external device
(disk).
NOTE: This signal is multiplexed on the MPP pins (see
Section 6, Pin Multiplexing, on page 61).
88F6192 – SATA Ports 0 and 1
SATA0_T_P/N
SATA1_T_P/N
O
CML
SATA0/1_AVDD
Transmit Data: Differential analog output of SATA II
port0/1
SATA0_R_P/N
SATA1_R_P/N
I
CML
SATA0/1_AVDD
Receive Data: Differential analog input of SATA II port0/1
SATA0_PRESENTn
SATA1_PRESENTn
O
CMOS
VDD_GE_B
When this signal is asserted there is an active link
between the SATA II port and the external device (disk).
NOTE: These signals are multiplexed on the MPP pins
(see Section 6, Pin Multiplexing, on page 61).
SATA0_ACTn
SATA1_ACTn
O
CMOS
VDD_GE_B
When this signal is asserted, there is an active and used
link between the SATA II port and the external device
(disk).
NOTE: These signals are multiplexed on the MPP pins
(see Section 6, Pin Multiplexing, on page 61).
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 31
88F619x
Hardware Specifications
2.2.6
Gigabit Ethernet Port Interface Pin Assignments
For additional information about the Gigabit Ethernet port pin functions refer to Section 6.2, Gigabit
Ethernet (GbE) Pins Multiplexing on MPP, on page 68.
For the 88F6190, Table 9 lists the Gigabit Ethernet port interface pin assignments.
For the 88F6192, Table 10 lists the Gigabit Ethernet port interface pin assignments.
Table 9:
88F6190 Gigabit Ethernet Interface Pin Assignments
Pin Name
I/O
P in
Ty p e
Power
R a il
D e s c r i p t io n
CMOS
VDD_GE_A
RGMII Transmit Clock
RGMII transmit reference output clock for GE_TXD[3:0] and
GE_TXCTL.
Provides 125 MHz, 25 MHz or 2.5 MHz clock.
Not used in MII/MMII mode.
Dedicated Ethernet Pins
GE_TXCLKOUT
t/s
O
GMII Transmit Clock
Provides the timing reference for the transfer of the transmit
enable, transmit error and transmit data signals. This clock
operates at 125 MHz.
GE_TXD[3:0]
t/s
O
CMOS
VDD_GE_A
RGMII Transmit Data
Contains the transmit data nibble outputs that run at double data
rate with bits [3:0] driven on the rising edge of GE_TXCLKOUT
and bits [7:4] driven on the falling edge.
GMII Transmit Data
Contains the transmit data nibble outputs.
GE_TXCTL
t/s
O
CMOS
VDD_GE_A
RGMII Transmit Control
Transmit control synchronous to the GE_TXCLKOUT output
rising/falling edge.
GE_TXEN is driven on the rising edge of GE_TXCLKOUT.
A logical derivative of transmit enable and transmit error is driven
on the falling edge of GE_TXCLKOUT.
GMII Transmit Enable
Indicates that the packet is being transmitted to the PHY.
It Is synchronous to GE_TXCLKOUT.
GE_RXD[3:0]
I
CMOS
VDD_GE_A
RGMII Receive Data
Contains the receive data nibble inputs that are synchronous to
GE_RXCLK input rising/falling edge.
GMII Receive Data
Contains the receive data nibble inputs.
GE_RXCTL
I
CMOS
VDD_GE_A
RGMII Receive Control
GE_RXCTL is presented on the rising edge of GE_RXCLK.
A logical derivative of receive data valid and receive data error is
presented on the falling edge of RXCLK.
GMII Receive Data Valid.
Doc. No. MV-S104987-U0 Rev. F
Page 32
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Pin and Signal Descriptions
Pin Descriptions
Table 9:
88F6190 Gigabit Ethernet Interface Pin Assignments (Continued)
Pin Name
I/O
P in
Ty p e
Power
R a il
D e s c r i p t io n
GE_RXCLK
I
CMOS
VDD_GE_A
RGMII Receive Clock
The receive clock provides a 125 MHz, 25 MHz, or 2.5 MHz
reference clock derived from the received data stream.
GMII Receive Clock
Provides the timing reference for the reception of the GE_RXDV,
receive error and receive data signals. This clock operates at
125 MHz
Multiplexed Ethernet Pins
MPP[23:20]/
GE1[3:0]
t/s
O
CMOS
VDD_GE_B
MII/MMII Transmit Data
Contains the transmit data nibble outputs that are synchronous
to the transmit clock input.
GMII Transmit Data
Contains the transmit data nibble outputs.
MPP[27:24]/
GE1[7:4]
I
CMOS
VDD_GE_B
MII/MMII Receive Data
Contains the receive data nibble inputs that are synchronous to
GE_RXCLK input.
GMII Receive Data
Contains the receive data nibble inputs.
MPP[28]/GE1[8]
I
CMOS
VDD_GE_B
MII/MMII Collision Detect
Indicates a collision has been detected on the wire. This input is
ignored in full-duplex mode. Collision detect is not synchronous
to any clock.
GMII Collision Detect
MPP[29]/GE1[9]
I
CMOS
VDD_GE_B
t/s
O
MPP[30]/GE1[10]
I
MII/MMII Transmit Clock
MII/MMII transmit reference clock from PHY.
Provides the timing reference for the transmission of the GMII
transmit clock, transmit enable, and GE_TXD[3:0] signals. This
clock operates at 2.5 MHz or 25 MHz.
GMII Transmit Clock
Provides the timing reference for the transfer of the transmit
enable, transmit error and transmit data signals. This clock
operates at 125 MHz.
CMOS
VDD_GE_B
MII/MMII Receive Data Valid
GMII Receive Error
MPP[31]/GE1[11]
I
CMOS
VDD_GE_B
MII/MMII Receive Clock
Provides the timing reference for the reception of the receive
data valid, receive error, and GE_RXD[3:0] signals. This clock
operates at 2.5 MHz or 25 MHz.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 33
88F619x
Hardware Specifications
Table 9:
88F6190 Gigabit Ethernet Interface Pin Assignments (Continued)
Pin Name
I/O
P in
Ty p e
Power
R a il
D e s c r i p t io n
MPP[32]/GE1[12]
I/O
CMOS
VDD_GE_B
MII/MMII Carrier Sense
Indicates that the receive medium is non-idle. In half-duplex
mode, GE_CRS is also asserted during transmission. Carrier
sense is not synchronous to any clock.
GMII Carrier Sense
MPP[33]/GE1[13]
t/s
O
CMOS
VDD_GE_B
MII/MMII Transmit Error
It is synchronous to transmit clock.
NOTE: Multiplexed on MPP.
GMII Transmit Error
It Is synchronous to GE_TXCLKOUT.
NOTE: Multiplexed on MPP.
MPP[34]/GE1[14]
O
CMOS
VDD_GE_B
MII/MMII Transmit Enable
Indicates that the packet is being transmitted to the PHY. It Is
synchronous to transmit clock.
MPP[35]/GE1[15]
I
CMOS
VDD_GE_B
MII/MMII Receive Error
Indicates that an error symbol, a false carrier, or a carrier
extension symbol is detected on the cable. It is synchronous to
GE_RXCLK input.
NOTE: Multiplexed on MPP.
Table 10: 88F6192 Gigabit Ethernet Port0/1 Interface Pin Assignments
Pin Name
I/O
P in
Ty p e
Power
R a il
D e s c r i p t io n
VDD_GE_A
RGMII Transmit Clock
RGMII transmit reference output clock for GE_TXD[3:0] and
GE_TXCTL.
Provides 125 MHz, 25 MHz or 2.5 MHz clock.
Not used in MII/MMII mode.
Port0—Dedicated GbE Pins
GE_TXCLKOUT
t/s
O
CMOS
I
MII/MMII Transmit Clock
MII/MMII transmit reference clock from PHY.
Provides the timing reference for the transmission of the MII
transmit clock, transmit enable, and GE_TXD[3:0] signals. This
clock operates at 2.5 MHz or 25 MHz.
t/s
O
GMII Transmit Clock
Provides the timing reference for the transfer of the transmit
enable, transmit error and transmit data signals. This clock
operates at 125 MHz.
Doc. No. MV-S104987-U0 Rev. F
Page 34
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Pin and Signal Descriptions
Pin Descriptions
Table 10: 88F6192 Gigabit Ethernet Port0/1 Interface Pin Assignments (Continued)
Pin Name
I/O
P in
Ty p e
Power
R a il
D e s c r i p t io n
GE_TXD[3:0]
t/s
O
CMOS
VDD_GE_A
RGMII Transmit Data
Contains the transmit data nibble outputs that run at double data
rate with bits [3:0] driven on the rising edge of GE_TXCLKOUT
and bits [7:4] driven on the falling edge.
MII/MMII Transmit Data
Contains the transmit data nibble outputs that are synchronous
to the transmit clock input.
GMII Transmit Data
Contains the transmit data nibble outputs.
GE_TXCTL
t/s
O
CMOS
VDD_GE_A
RGMII Transmit Control
Transmit control synchronous to the GE_TXCLKOUT output
rising/falling edge.
GE_TXEN is driven on the rising edge of GE_TXCLKOUT.
A logical derivative of transmit enable and transmit error is driven
on the falling edge of GE_TXCLKOUT.
MII/MMII Transmit Enable
Indicates that the packet is being transmitted to the PHY. It Is
synchronous to transmit clock.
GMII Transmit Enable
Indicates that the packet is being transmitted to the PHY.
It Is synchronous to GE_TXCLKOUT.
GE_RXD[3:0]
I
CMOS
VDD_GE_A
RGMII Receive Data (Only relevant for the 88F6192.)
Contains the receive data nibble inputs that are synchronous to
GE_RXCLK input rising/falling edge.
MII/MMII Receive Data
Contains the receive data nibble inputs that are synchronous to
GE_RXCLK input.
GMII Receive Data
Contains the receive data nibble inputs.
GE_RXCTL
I
CMOS
VDD_GE_A
RGMII Receive Control
GE_RXCTL is presented on the rising edge of GE_RXCLK.
A logical derivative of receive data valid and receive data error is
presented on the falling edge of RXCLK.
MII/MMII Receive Data Valid
GMII Receive Data Valid.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 35
88F619x
Hardware Specifications
Table 10: 88F6192 Gigabit Ethernet Port0/1 Interface Pin Assignments (Continued)
Pin Name
I/O
P in
Ty p e
Power
R a il
D e s c r i p t io n
GE_RXCLK
I
CMOS
VDD_GE_A
RGMII Receive Clock
The receive clock provides a 125 MHz, 25 MHz, or 2.5 MHz
reference clock derived from the received data stream.
MII/MMII Receive Clock
Provides the timing reference for the reception of the receive
data valid, receive error, and GE_RXD[3:0] signals. This clock
operates at 2.5 MHz or 25 MHz.
GMII Receive Clock
Provides the timing reference for the reception of the GE_RXDV,
receive error and receive data signals. This clock operates at
125 MHz
Port1—Multiplexed GbE Pins
MPP[23:20]/
GE1[3:0]
t/s
O
CMOS
VDD_GE_B
RGMII Transmit Data
Contains the transmit data nibble outputs that run at double data
rate with bits [3:0] presented on the rising edge of
GE_TXCLKOUT and bits [7:4] presented on the falling edge.
MII/MMII Transmit Data
Contains the transmit data nibble outputs that are synchronous
to the transmit clock input.
GMII Transmit Data
Contains the transmit data nibble outputs.
MPP[27:24]/
GE1[7:4]
I
CMOS
VDD_GE_B
RGMII Receive Data
Contains the receive data nibble inputs that are synchronous to
GE_RXCLK input rising/falling edge.
MII/MMII Receive Data
Contains the receive data nibble inputs that are synchronous to
GE_RXCLK input.
GMII Receive Data
Contains the receive data nibble inputs.
Doc. No. MV-S104987-U0 Rev. F
Page 36
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Pin and Signal Descriptions
Pin Descriptions
Table 10: 88F6192 Gigabit Ethernet Port0/1 Interface Pin Assignments (Continued)
Pin Name
I/O
P in
Ty p e
Power
R a il
D e s c r i p t io n
MPP[28]/GE1[8]
I
CMOS
VDD_GE_B
MII/MMII Collision Detect
Indicates a collision has been detected on the wire. This input is
ignored in full-duplex mode. Collision detect is not synchronous
to any clock.
GMII Collision Detect
MPP[29]/GE1[9]
I
CMOS
VDD_GE_B
t/s
O
MPP[30]/GE1[10]
I
MII/MMII Transmit Clock
MII/MMII transmit reference clock from PHY.
Provides the timing reference for the transmission of the MII
transmit clock, transmit enable, and GE_TXD[3:0] signals. This
clock operates at 2.5 MHz or 25 MHz.
GMII Transmit Clock
Provides the timing reference for the transfer of the transmit
enable, transmit error and transmit data signals. This clock
operates at 125 MHz.
CMOS
VDD_GE_B
RGMII Receive Control
GE_RXCTL is presented on the rising edge of GE_RXCLK.
A logical derivative of receive data valid and receive data error is
presented on the falling edge of RXCLK.
MII/MMII Receive Data Valid
GMII Receive Error
MPP[31]/GE1[11]
I
CMOS
VDD_GE_B
RGMII Receive Clock
The receive clock provides a 125 MHz, 25 MHz, or 2.5 MHz
reference clock derived from the received data stream.
MII/MMII Receive Clock
Provides the timing reference for the reception of the receive
data valid, receive error, and GE_RXD[3:0] signals. This clock
operates at 2.5 MHz or 25 MHz.
MPP[32]/GE1[12]
I/O
CMOS
VDD_GE_B
RGMII Transmit Clock
RGMII transmit reference output clock for GE_TXD[3:0] and
GE_TXCTL Provides 125 MHz, 25 MHz or 2.5 MHz clock.
Not used in MII/MMII mode.
MII/MMII Carrier Sense
Indicates that the receive medium is non-idle. In half-duplex
mode, GE_CRS is also asserted during transmission. Carrier
sense is not synchronous to any clock.
GMII Carrier Sense
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 37
88F619x
Hardware Specifications
Table 10: 88F6192 Gigabit Ethernet Port0/1 Interface Pin Assignments (Continued)
Pin Name
I/O
P in
Ty p e
Power
R a il
D e s c r i p t io n
t/s
O
CMOS
VDD_GE_B
RGMII Transmit Control
Transmit control synchronous to the GE_TXCLKOUT output
rising/falling edge.
GE_TXEN is presented on the rising edge of GE_TXCLKOUT.
A logical derivative of transmit enable transmit error is presented
on the falling edge of GE_TXCLKOUT.
MPP[33]/GE1[13]
MII/MMII Transmit Error
It is synchronous to transmit clock.
NOTE: Multiplexed on MPP.
GMII Transmit Error
It Is synchronous to GE_TXCLKOUT.
NOTE: Multiplexed on MPP.
MPP[34]/GE1[14]
O
CMOS
VDD_GE_B
MII/MMII Transmit Enable
Indicates that the packet is being transmitted to the PHY. It Is
synchronous to transmit clock.
MPP[35]/GE1[15]
I
CMOS
VDD_GE_B
MII/MMII Receive Error
Indicates that an error symbol, a false carrier, or a carrier
extension symbol is detected on the cable. It is synchronous to
GE_RXCLK input.
NOTE: Multiplexed on MPP.
Doc. No. MV-S104987-U0 Rev. F
Page 38
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Pin and Signal Descriptions
Pin Descriptions
2.2.7
Serial Management Interface (SMI) Interface Pin
Assignments
Table 11: Serial Management Interface (SMI) Pin Assignments
Pin Name
I/O
P in
Ty p e
Power
R a il
D e s c r i p t io n
GE_MDC
t/s
O
CMOS/
VDD_GE_A
Management Data Clock
MDC is derived from TCLK divided by 128.
Provides the timing reference for the transfer of the MDIO signal.
GE_MDIO
t/s
I/O
CMOS
VDD_GE_A
Management Data In/Out
Used to transfer control and status information between PHY
devices and the GbE controller.
NOTE: An external pull-up is required.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 39
88F619x
Hardware Specifications
2.2.8
USB 2.0 Interface Pin Assignments
Table 12: USB 2.0 Interface Pin Assignments
Pin Name
I/O
Pi n
Ty p e
P ow e r
R ai l
D e s c r ip t i o n
USB_DP
USB_DM
I/O
CML
USB_AVDD
USB 2.0 Data Differential Pair
Doc. No. MV-S104987-U0 Rev. F
Page 40
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Pin and Signal Descriptions
Pin Descriptions
2.2.9
JTAG Interface Pin Assignment
Table 13: JTAG Pin Assignment
Pin Name
I/O
P in
Ty p e
Power
R a il
D e s c r i p t io n
JT_CLK
I
CMOS
VDDO
JTAG Clock
Clock input for the JTAG controller.
NOTE: This pin is internally pulled down to 0.
JT_RSTn
I
CMOS
VDDO
JTAG Reset
When asserted, resets the JTAG controller.
NOTE: This pin is internally pulled down to 0.1
JT_TMS_CPU
I
CMOS
VDDO
CPU JTAG Mode Select
Controls CPU JTAG controller state.
Sampled with the rising edge of JT_CLK.
NOTE: This pin is internally pulled up to 1.
JT_TMS_CORE
I
CMOS
VDDO
Core JTAG Mode Select
Controls the Core JTAG controller state.
Sampled with the rising edge of JT_CLK.
NOTE: This pin is internally pulled up to 1.
JT_TDO
O
CMOS
VDDO
JTAG Data Out
Driven on the falling edge of JT_CLK.
JT_TDI
I
CMOS
VDDO
JTAG Data In
JTAG serial data input. Sampled with the JT_CLK rising edge.
NOTE: This pin is internally pulled up to 1.
1. If this pull-down conflicts with other devices, the JTAG tool must not use this signal. This signal is not mandatory for the
JTAG interface, since the TAP (Test Access Port) can be reset by driving the JT_TMS signal HIGH for 5 JT_CLK cycles.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 41
88F619x
Hardware Specifications
2.2.10
Real Time Clock (RTC) Interface Pin Assignments
Table 14: RTC Interface Pin Assignments
Pin Name
I/O
P in
Ty p e
Power
R a il
D e s c r i p t io n
RTC_XIN
I
Analog
RTC_AVDD
RTC Crystal Clock Input
RTC_XOUT
O
Analog
RTC_AVDD
RTC Crystal Clock Feedback
Doc. No. MV-S104987-U0 Rev. F
Page 42
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Pin and Signal Descriptions
Pin Descriptions
2.2.11
NAND Flash Interface Pin Assignment
Table 15: NAND Flash Interface Pin Assignment
Pin Name
I/O
P in
Ty p e
Power
R a il
D e s c r i p t io n
NF_IO[7:0]
I/O
CMOS
VDDO
Data Input/Output
Used to output command, address and data, and to input data
during read operations.
NOTE: All of the NF_IO pins are multiplexed on the MPP pins
(see Section 6, Pin Multiplexing, on page 61)
NF_CLE
O
CMOS
VDDO
Command Latch Enable
Controls the activating path for commands sent to the command
register.
NF_ALE
O
CMOS
VDDO
Address Latch Enable
Controls the activating path for the address to the internal
address registers.
NF_CEn
O
CMOS
VDDO
Chip Enable
Controls the device selection.
NF_REn
O
CMOS
VDDO
Read Enable
Controls the serial data-in.
NF_WEn
O
CMOS
VDDO
Write Enable
Controls writes to the NF_IO[7:0] ports.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 43
88F619x
Hardware Specifications
2.2.12
MPP Interface Pin Assignment
Table 16: MPP Interface Pin Assignment
Pin Name
I/O
P in
Ty p e
Power
R a il
D e s c r i p t io n
MPP[19:0]
t/s
I/O
CMOS
VDDO
Multi Purpose Pin
Various functionalities
MPP[35:20]
t/s
I/O
CMOS
VDD_GE_B
Multi Purpose Pin
Various functionalities
Note
The various functionalities of the MPP pins are detailed in Section 6, Pin Multiplexing,
on page 61.
Doc. No. MV-S104987-U0 Rev. F
Page 44
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Pin and Signal Descriptions
Pin Descriptions
2.2.13
Two-Wire Serial Interface (TWSI) Interface
All of the TWSI signals are multiplexed on the MPP pins (see Section 6, Pin Multiplexing,
Note
on page 61).
Table 17: Two-Wire Serial Interface (TWSI) Interface Pin Assignment
Pin Name
I/O
P in
Ty p e
Power
R a il
D e s c r i p t io n
TW_SDA
o/d
I/O
CMOS
VDDO
TWSI Port Serial Data
Address or write data driven by the TWSI master or read
response data driven by the TWSI slave.
NOTE: Requires a pull-up resistor to VDDO.
TW_SCK
o/d
I/O
CMOS
VDDO
TWSI Port Serial Clock
Serves as output when acting as an TWSI master.
Serves as input when acting as an TWSI slave.
NOTE: Requires a pull-up resistor to VDDO.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 45
88F619x
Hardware Specifications
2.2.14
UART Interface
Note
All of the UART signals are multiplexed on the MPP pins (see Section 6, Pin Multiplexing,
on page 61).
Table 18: UART Port 0/1 Interface Pin Assignment
Pin Name
I/O
P in
Ty p e
Power
R a il
D e s c r i p t io n
UA0/1_RXD
I
CMOS
VDDO
UART Port 0/1 RX Data
UA0/1_TXD
O
CMOS
VDDO
UART Port 0/1 TX Data
UA0/1_CTS
I
CMOS
VDDO
Clear to Send
UA0/1_RTS
O
CMOS
VDDO
Request to Send
Doc. No. MV-S104987-U0 Rev. F
Page 46
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Pin and Signal Descriptions
Pin Descriptions
2.2.15
Audio (S/PDIF / I2S) Interface
„
„
Note
„
„
The Audio interface is only relevant for the 88F6192.
All of the Audio signals are multiplexed on the MPP pins (see Section 6, Pin
Multiplexing, on page 61).
If the Audio interface is not used, leave all of the signals unconnected.
The Audio signals are powered on VDDO or on VDD_GE_B, based on the pin
multiplexing option.
Table 19: Audio (S/PDIF / I2S) Interface Signal Assignment
Pin Name
I/O
P in
Ty p e
Power
R a il
D e s c r i p t io n
AU_SPDIFI
I
CMOS
VDD_GE_B
S/PDIF In
AU_SPDIFO
O
CMOS
VDD_GE_B
S/PDIF Out
AU_
SPDFRMCLK
O
CMOS
VDD_GE_B
S/PDIF Recovered Master Clock (256 x Fs)1
For the frequency of this clock, see the Audio External
Reference Clock section of Table 51, Reference Clock AC
Timing Specifications, on page 97.
AU_I2SBCLK
O
CMOS
VDD_GE_B
I2S Bit Clock (64 x Fs)
AU_I2SDO
O
CMOS
VDD_GE_B
Transmitter Data Out
AU_I2SLRCLK
O
CMOS
VDD_GE_B
I2S Left/Right Clock (1 x Fs)
AU_I2SMCLK
O
CMOS
VDD_GE_B
I2S Master Clock (256 x Fs)
AU_I2SDI
I
CMOS
VDD_GE_B
I2S Receiver Data In
AU_EXTCLK
I
CMOS
VDD_GE_B
External Audio Clock
For the frequency of this clock, see the Audio External
Reference Clock section of Table 51, Reference Clock AC
Timing Specifications, on page 97.
1. Fs is the audio sample rate.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 47
88F619x
Hardware Specifications
2.2.16
Serial Peripheral Interface (SPI) Interface
All of the SPI signals are multiplexed on the MPP pins (see Section 6, Pin Multiplexing,
Note
on page 61).
Table 20: Serial Peripheral Interface (SPI) Interface Signal Assignment
Pin Name
I/O
Pin Type
Power Rail
Description
SPI_MOSI1
O
CMOS
VDDO
SPI Data Output
Data is output from the master and input to the slave.
SPI_MISO2
I
CMOS
VDDO
SPI Data Input
Data is input to the master and output from the slave.
SPI_SCK
O
CMOS
VDDO
SPI Clock
SPI_CSn
O
CMOS
VDDO
SPI Chip Select
NOTE: This pin requires an external pull up.
1. MOSI = Master Out Slave In.
2. MISO = Master In Slave Out.
Doc. No. MV-S104987-U0 Rev. F
Page 48
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Pin and Signal Descriptions
Pin Descriptions
2.2.17
Secure Digital Input/Output (SDIO) Interface
All of the SDIO signals are multiplexed on the MPP pins (see Section 6, Pin Multiplexing,
Note
on page 61).
Table 21: Secure Digital Input/Output (SDIO) Interface Signal Assignment
Pin Name
I/O
Pin Type
Power Rail
Description
SD_CLK
O
CMOS
VDDO
SDIO Clock
SD_CMD
I/O
CMOS
VDDO
SDIO Command
Used to transfer a command serially from the SDIO host to the
SDIO device. Used to transfer a command response serially
from the SDIO device to the SDIO host.
NOTE: This pin requires a pull up on board.
SD_D[3:0]
I/O
CMOS
VDDO
SDIO Data Input/Output
Used to transfer data from the SDIO host to the SDIO device or
vice versa.
NOTE: These pins require a pull up on board.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 49
88F619x
Hardware Specifications
2.2.18
Time Division Multiplexing (TDM) Interface
„
„
Note
„
The TDM interface is only relevant for the 88F6192.
All of the TDM signals are multiplexed on the MPP pins (see Section 6, Pin
Multiplexing, on page 61).
The TDM signals are powered on VDDO or on VDD_GE_B, based on the pin
multiplexing option (see Section 6, Pin Multiplexing, on page 61).
Table 22: Time Division Multiplexing (TDM) Interface Signal Assignment
Pin Name
I/O
Pin Type
Power Rail
Description
TDM_CH0_TX_
QL
O
CMOS
VDD_GE_B
TDM Channel0 Transmit Qualifier
TDM_CH2_TX_
QL
O
CMOS
VDD_GE_B
TDM Channel2 Transmit Qualifier
TDM_CH0_RX_
QL
O
CMOS
VDD_GE_B
TDM Channel0 Receive Qualifier
TDM_CH2_RX_
QL
O
CMOS
VDD_GE_B
TDM Channel2 Receive Qualifier
TDM_CODEC_
INTn
I
CMOS
VDD_GE_B
Interrupt Signal FROM the SLIC/codec
TDM_CODEC_
RSTn
O
CMOS
VDD_GE_B
SLIC/codec Reset Signal
TDM_PCLK
I/O
CMOS
VDD_GE_B
PCM Audio Bit Clock
TDM_FS
I/O
CMOS
VDD_GE_B
TDM Frame Sync Signal
TDM_DRX
I
CMOS
VDD_GE_B
PCM Audio Input Data (for recording)
TDM_DTX
O
CMOS
VDD_GE_B
PCM Audio Output Data (for playback)
TDM_SPI_CS[1:0]
O
CMOS
VDD_GE_B
Active low SPI chip selects driven by the host to the codec for
register access. Always asserted for eight SCLK cycles at a time.
Only Byte-by-Byte mode codec register read/write is supported.
TDM_SPI_SCK
O
CMOS
VDD_GE_B
Serial SPI clock from the host to the codec for register access.
This is an RTO (return to one) clock. It toggles for eight cycles at
a time (for 1 byte transfer) during codec register access, then it
returns to high.
The host drives write data on TDM_SPI_MOSI on the negative
edge of TDM_SPI_SCK, and captures read data from the codec
on the positive edge of TDM_SPI_SCK.
Doc. No. MV-S104987-U0 Rev. F
Page 50
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Pin and Signal Descriptions
Pin Descriptions
Table 22: Time Division Multiplexing (TDM) Interface Signal Assignment (Continued)
Pin Name
I/O
Pin Type
Power Rail
Description
TDM_SPI_MOSI
O
CMOS
VDD_GE_B
Serial SPI data from the host to the codec for register access.
When TDM_SPI_CS is asserted low, the data is driven from the
host on the negative edge of TDM_SPI_SCK. It is always driven
for eight TDM_SPI_SCK cycles at a time.
In a byte, the data can be driven MSB or LSB first.
TDM_SPI_MISO
I
CMOS
VDD_GE_B
Serial SPI read data from the CODEC to the host for register
access.
When TDM_SPI_CS is asserted low, this data is driven from
CODEC on negative edge of TDM_SPI_SCK. It is always driven
for eight TDM_SPI_SCK cycles at a time. The CODEC drives
data on this line only for a read operation, when it gets command
and address in previous bytes from the host on TDM_SPI_MOSI
In a byte, the data can be driven MSB or LSB first.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 51
88F619x
Hardware Specifications
2.2.19
Transport Stream (TS) Interface
„
„
Note
„
The TS interface is only relevant for the 88F6192 only.
All of the TS signals are multiplexed on the MPP pins (see Section 6, Pin
Multiplexing, on page 61).
The TS signals are powered on VDDO or on VDD_GE_B based on the pin
multiplexing option (see Section 6, Pin Multiplexing).
Table 23: Transport Stream (TS) Interface Signal Assignment
Pin Name
I/O
Pin Type
Power Rail
Description
TSMP[0]
I
CMOS
VDD_GE_B
EXT_CLK
External clock that can be used to drive the TS0_CLK and
TS1_CLK
TSMP[1]
I/O
CMOS
VDD_GE_B
TS0_CLK
Port0 TS clock.
• If TS0_VAL is used, the clock may be continuous.
• If TS0_VAL is not used, the clock may toggle only when valid
data is available on TS0_DATA.
TSMP[2]
I/O
CMOS
VDD_GE_B
TS0_SYNC
Port0 Sync/Frame Start Indicator or Packet Clock.
The TS0_SYNC in parallel mode is a pulse that is active during
the first (Sync) byte of the TS packet. In serial mode, the
TS0_SYNC pulse may be active for the entire byte or only for the
first bit. The polarity is programmable to be either active high or
active low.
TSMP[3]
I/O
CMOS
VDD_GE_B
TS0_VAL
Port0 Valid Data Indicator
When this signal is used and is valid, it indicates that valid data is
present on TS0_DATA. TS0_VAL is active during the TS frame
packet data and inactive when there is no TS synchronization.
In output mode, the polarity of TS0_VAL is programmable to be
either active high or active low.
TSMP[4]
I/O
CMOS
VDD_GE_B
TS0_ERR
Port0 Uncorrectable Packet Error
When this signal is used, an error indicates that the packet
contains an uncorrectable error, and therefore should not be
used.
In output mode, the TS0_ERR is active during the entire TS
frame.
TSMP[5]
I/O
CMOS
VDD_GE_B
TS0_DATA[0]
Port0 TS Data bit 0 in both parallel and serial modes.
In Serial mode TS0_DATA[0] is used as data input or output.
TSMP[6]
I/O
CMOS
VDD_GE_B
•
•
Parallel Mode:
TS0_DATA[1]: Port0 TS Data bit 1
Serial Mode:
TS1_CLK: Port1 TS clock.
- If TS1_VAL is used, the clock may be continuous.
- If TS1_VAL is not used, the clock may toggle only when
valid data is available on TS1_DATA
Doc. No. MV-S104987-U0 Rev. F
Page 52
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Pin and Signal Descriptions
Pin Descriptions
Table 23: Transport Stream (TS) Interface Signal Assignment (Continued)
Pin Name
I/O
Pin Type
Power Rail
Description
TSMP[7]
I/O
CMOS
VDD_GE_B
•
•
TSMP[8]
I/O
CMOS
VDD_GE_B
•
•
TSMP[9]
I/O
CMOS
VDD_GE_B
•
•
TSMP[10]
I/O
CMOS
VDD_GE_B
•
•
Parallel Mode:
TS0_DATA[2]: Port0 TS Data bit 2
Serial Mode:
TS1_SYNC: Port1 Sync/Frame Start Indicator or Packet
Clock.
The TS1_SYNC pulse may be active for the entire byte or
only for the first bit. The polarity is programmable to be either
active high or active low
Parallel Mode:
TS0_DATA[3]: Port0 TS Data bit 3
Serial Mode:
TS1_VAL: Port1Valid Data Indicator
When this signal is used and is valid, it indicates that valid
data is present on TS1_DATA[0].
TS1_VAL is active during the TS frame packet data and
inactive when there is no TS synchronization.
In output mode, the polarity of TS1_VAL is programmable to
be either active high or active low.
Parallel Mode:
TS0_DATA[4]: Port0 TS Data bit 4
Serial Mode:
TS1_ERR: Port1 Uncorrectable Packet Error
When this signal is used, an error indicates that the packet
contains an uncorrectable error, and, therefore, should not
be used.
In output mode the TS1_ERR is active during the entire TS
frame.
Parallel Mode:
TS0_DATA[5]: Port0 TS Data bit 5
Serial Mode:
TS1_DATA[0]: Port1 TS Data bit 0, used as data input or
output.
TSMP[11]
I/O
CMOS
VDD_GE_B
TS0_DATA[6]
Port0 TS Data bit 6
This pin is only valid in Parallel mode.
TSMP[12]
I/O
CMOS
VDD_GE_B
TS0_DATA[7]
Port0 TS Data bit 7
This pin is only valid in Parallel mode.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 53
88F619x
Hardware Specifications
2.2.20
Precise Timing Protocol (PTP) Interface
Note
All of the PTP signals are multiplexed on the MPP pins (see Section 6, Pin Multiplexing,
on page 61).
Table 24: Precise Timing Protocol (PTP) Interface Signal Assignment
Pin Name
I/O
Pin Type
Power Rail
Description
PTP_CLK
I
CMOS
VDDO
PTP Clock
PTP_EVENT_REQ
I
CMOS
VDDO
Trigger generation to the PTP core.
PTP_TRIG_GEN
O
CMOS
VDDO
Trigger generated by the PTP core.
Doc. No. MV-S104987-U0 Rev. F
Page 54
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Pin and Signal Descriptions
Internal Pull-up and Pull-down Pins
2.3
Internal Pull-up and Pull-down Pins
Some pins of the device package are connected to internal pull-up and pull-down resistors. When
these pins are Not Connected (NC) on the system board, these resistors set the default value for
input and sample at reset configuration pins.
The internal pull-up and pull-down resistor value is 50 kΩ. An external resistor with a lower value can
override this internal resistor.
Table 25: Internal Pull-up and Pull-down Pins
P in N a m e
P in N u m be r
Pu l l up / Pu l l do w n
GE_TXD[0]
22
Pull down
GE_TXD[1]
21
Pull down
GE_TXD[2]
20
Pull up
GE_TXD[3]
19
Pull up
88F6190 – GE_TXEN
88F6192 – GE_TXCTL
23
Pull down
GE_MDC
33
Pull up
JT_TMS_CORE
114
Pull up
JT_RSTn
109
Pull down
JT_TDI
115
Pull up
JT_TMS_CPU
112
Pull up
NF_ALE
90
Pull up
NF_REn
93
Pull down
NF_CLE
92
Pull down
NF_CEn
91
Pull up
NF_WEn
94
Pull up
MPP[1]
81
Pull down
MPP[2]
80
Pull down
MPP[3]
82
Pull down
MPP[4]
85
Pull up
MPP[5]
86
Pull up
MPP[7]
75
Pull up
MPP[10]
72
Pull down
MPP[11]
74
Pull up
MPP[12]
97
Pull down
MPP[14]
99
Pull up
MPP[18]
88
Pull up
MPP[19]
89
Pull up
MPP[33]
45
Pull down
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 55
88F619x
Hardware Specifications
3
Unused Interface Strapping
Table 26 lists the signal strapping to be used for systems in which some of the device interfaces are unused (not
connected).
Table 26: Unused Interface Strapping
Unused Interface
Str a pp i ng
Ethernet SMI
Pull up GE_MDIO.
MPP
Configure any unused MPP pin to GPIO output.
Leave the power supply connected.
• If the related power supply is VDDO, leave it connected to 3.3V.
• If the related power supply is VDD_GE_B, leave it connected to either 3.3V or 1.8V.
USB
Discard the power filter.
Leave USB_AVDD connected to 3.3V.
All other signals can be left unconnected.
PCI Express
Discard the analog power filters.
Leave PEX_AVDD connected to 1.8V.
Pull down the PEX_CLK_N signal through a 50 kΩ resistor to GND.
Pull up the PEX_CLK_P signal through a 16 kΩ resistor to 1.8V.
All other signals can be left unconnected.
Configure the PEX_CLK_P and PEX_CLK_N signals as inputs, as indicated in Table 38,
Reset Configuration, on page 77.
88F6190 – SATA
Discard the analog power filters.
SATA_AVDD can be left unconnected.
88F6192 – SATA
Discard the analog power filters.
SATA0_AVDD/SATA1_AVDD can be left unconnected.
RTC
Connect RTC_AVDD, RTC_AVSS, RTC_XIN, and RTC_XOUT to GND.
SSCG
Discard the power filter.
Leave SSCG_AVDD connected to 1.8V.
eFuse
Connect VHV to VDD
Doc. No. MV-S104987-U0 Rev. F
Page 56
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
88F6190 Pinout
4
88F6190 Pinout
This section provides the pin map and pin list for the 88F6190.
162
161
160
159
158
157
156
155
154
153
152
151
150
149
148
147
146
145
144
143
142
141
140
139
138
137
136
135
134
133
132
131
130
129
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
VDD_M
M_CLKOUT
M_CLKOUTn
VDD_M
M_STARTBURST
M_NCAL
VDD
M_STARTBURST_IN
M_PCAL
VSS
RTC_XOUT
RTC_XIN
RTC_AVDD
PEX_AVDD
PEX_CLK_P
PEX_CLK_N
TP
PEX_RX_P
PEX_RX_N
PEX_AVDD
PEX_TX_P
VSS
PEX_TX_N
VSS
PEX_ISET
CORE_PLL_AVDD
VDD
XOUT
REF_CLK_XIN
XTAL_AVDD
XTAL_AVSS
ISET
VDD
VSS
VDD
VSS
VDD
VSS
VDD
VDD
VSS
VDD
VSS
VDD
VSS
VDD
SSCG_AVDD
JT_TDI
JT_TMS_CORE
JT_TDO
JT_TMS_CPU
VDDO
SYSRSTn
JT_RSTn
Figure 3: 88F6190 Pin Map Top View
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
88F6190
Top View
JT_CLK
VDD
VSS
VDD
CPU_PLL_AVDD
VDD
VDDO
MPP[17]
MPP[16]
MPP[14]
MPP[15]
MPP[12]
MPP[13]
VDDO
NF_WEn
NF_REn
NF_CLE
NF_CEn
NF_ALE
MPP[19]
MPP[18]
VSS
MPP[5]
MPP[4]
VSS
MPP[0]
MPP[3]
MPP[1]
MPP[2]
VDDO
MPP[9]
MPP[8]
VSS
MPP[7]
MPP[11]
MPP[6]
MPP[10]
VDD
VSS
SATA_T_P
VSS
SATA_T_N
SATA_AVDD
SATA_R_N
SATA_R_P
VDD
NC
NC
NC
NC
NC
NC
NC
VDD
VDD_M
1
M_DM[1]
2
M_DQS[1]
3
M_DQSn[1]
4
VDD_M
5
M_DQ[15]
6
M_DQ[8]
7
VDD_M
8
M_DQ[10]
9
M_DQ[13]
10
VSS
11
VDD
12
USB_AVDD 13
USB_DP
14
USB_DM
15
VDD
16
VHV
17
VDD_GE_A 18
19
GE_TXD[3]
20
GE_TXD[2]
21
GE_TXD[1]
22
GE_TXD[0]
23
GE_TXCTL
GE_TCLKOUT24
VDD_GE_A 25
GE_RXCLK 26
GE_RXCTL 27
28
GE_RXD[0]
29
GE_RXD[1]
30
GE_RXD[2]
31
GE_RXD[3]
32
VSS
33
GE_MDC
34
GE_MDIO
35
VSS
36
MPP[28]
37
MPP[29]
38
MPP[34]
39
MPP[35]
VDD_GE_B 40
41
MPP[23]
42
MPP[22]
43
MPP[20]
44
MPP[21]
45
MPP[33]
46
MPP[32]
VDD_GE_B 47
48
MPP[31]
49
MPP[30]
50
MPP[24]
51
MPP[25]
52
MPP[26]
53
MPP[27]
54
VDD
M_ODT[0]
M_CSn[1]
M_RASn
M_CSn[0]
VDD_M
M_CASn
M_A[0]
M_A[2]
M_A[4]
VDD_M
M_A[6]
M_A[8]
M_A[13]
M_A[11]
VDD_M
VDD
M_DQ[5]
M_DQ[0]
VDD_M
M_DQ[2]
M_DQ[7]
VDD_M
M_DQS[0]
M_DQSn[0]
M_DM[0]
VDD_M
M_DQ[6]
M_DQ[1]
VDD_M
M_DQ[3]
M_DQ[4]
VDD
VDD_M
M_A[9]
M_A[12]
M_A[5]
M_A[7]
VDD_M
M_A[1]
M_A[3]
M_BA[1]
M_A[10]
VDD_M
M_BA[2]
M_WEn
M_BA[0]
M_CKE
VDD_M
VDD
M_DQ[12]
M_DQ[11]
VDD_M
M_DQ[14]
M_DQ[9]
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 57
88F619x
Hardware Specifications
Table 27: 88F6190 Pinout Sorted by Pin Number
Pin # Pin Nam e
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
VDD_M
M_DM[1]
M_DQS[1]
M_DQSn[1]
VDD_M
M_DQ[15]
M_DQ[8]
VDD_M
M_DQ[10]
M_DQ[13]
VSS
VDD
USB_AVDD
USB_DP
USB_DM
VDD
VHV
VDD_GE_A
GE_TXD[3]
GE_TXD[2]
GE_TXD[1]
GE_TXD[0]
GE_TXCTL
GE_TCLKOUT
VDD_GE_A
GE_RXCLK
GE_RXCTL
GE_RXD[0]
GE_RXD[1]
GE_RXD[2]
GE_RXD[3]
VSS
GE_MDC
GE_MDIO
VSS
MPP[28]
MPP[29]
MPP[34]
MPP[35]
VDD_GE_B
MPP[23]
MPP[22]
MPP[20]
MPP[21]
MPP[33]
Pin # Pin Nam e
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
Pin # Pin Nam e
MPP[32]
VDD_GE_B
MPP[31]
MPP[30]
MPP[24]
MPP[25]
MPP[26]
MPP[27]
VDD
VDD
NC
NC
NC
NC
NC
NC
NC
VDD
SATA_R_P
SATA_R_N
SATA_AVDD
SATA_T_N
VSS
SATA_T_P
VSS
VDD
MPP[10]
MPP[6]
MPP[11]
MPP[7]
VSS
MPP[8]
MPP[9]
VDDO
MPP[2]
MPP[1]
MPP[3]
MPP[0]
VSS
MPP[4]
MPP[5]
VSS
MPP[18]
MPP[19]
NF_ALE
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
NF_CEn
NF_CLE
NF_REn
NF_WEn
VDDO
MPP[13]
MPP[12]
MPP[15]
MPP[14]
MPP[16]
MPP[17]
VDDO
VDD
CPU_PLL_AVDD
VDD
VSS
VDD
JT_CLK
JT_RSTn
SYSRSTn
VDDO
JT_TMS_CPU
JT_TDO
JT_TMS_CORE
JT_TDI
SSCG_AVDD
VDD
VSS
VDD
VSS
VDD
VSS
VDD
VDD
VSS
VDD
VSS
VDD
VSS
VDD
ISET
XTAL_AVSS
XTAL_AVDD
REF_CLK_XIN
XOUT
Pin # Pin Nam e
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
Doc. No. MV-S104987-U0 Rev. F
Page 58
Pin # Pin Nam e
VDD
CORE_PLL_AVDD
PEX_ISET
VSS
PEX_TX_N
VSS
PEX_TX_P
PEX_AVDD
PEX_RX_N
PEX_RX_P
TP
PEX_CLK_N
PEX_CLK_P
PEX_AVDD
RTC_AVDD
RTC_XIN
RTC_XOUT
VSS
M_PCAL
M_STARTBURST_IN
VDD
M_NCAL
M_STARTBURST
VDD_M
M_CLKOUTn
M_CLKOUT
VDD_M
M_ODT[0]
M_CSn[1]
M_RASn
M_CSn[0]
VDD_M
M_CASn
M_A[0]
M_A[2]
M_A[4]
VDD_M
M_A[6]
M_A[8]
M_A[13]
M_A[11]
VDD_M
VDD
M_DQ[5]
M_DQ[0]
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
VDD_M
M_DQ[2]
M_DQ[7]
VDD_M
M_DQS[0]
M_DQSn[0]
M_DM[0]
VDD_M
M_DQ[6]
M_DQ[1]
VDD_M
M_DQ[3]
M_DQ[4]
VDD
VDD_M
M_A[9]
M_A[12]
M_A[5]
M_A[7]
VDD_M
M_A[1]
M_A[3]
M_BA[1]
M_A[10]
VDD_M
M_BA[2]
M_WEn
M_BA[0]
M_CKE
VDD_M
VDD
M_DQ[12]
M_DQ[11]
VDD_M
M_DQ[14]
M_DQ[9]
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
88F6192 Pinout
5
88F6192 Pinout
This section provides the pin map and pin list for the 88F6192.
162
161
160
159
158
157
156
155
154
153
152
151
150
149
148
147
146
145
144
143
142
141
140
139
138
137
136
135
134
133
132
131
130
129
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
VDD_M
M_CLKOUT
M_CLKOUTn
VDD_M
M_STARTBURST
M_NCAL
VDD
M_STARTBURST_IN
M_PCAL
VSS
RTC_XOUT
RTC_XIN
RTC_AVDD
PEX_AVDD
PEX_CLK_P
PEX_CLK_N
TP
PEX_RX_P
PEX_RX_N
PEX_AVDD
PEX_TX_P
VSS
PEX_TX_N
VSS
PEX_ISET
CORE_PLL_AVDD
VDD
XOUT
REF_CLK_XIN
XTAL_AVDD
XTAL_AVSS
ISET
VDD
VSS
VDD
VSS
VDD
VSS
VDD
VDD
VSS
VDD
VSS
VDD
VSS
VDD
SSCG_AVDD
JT_TDI
JT_TMS_CORE
JT_TDO
JT_TMS_CPU
VDDO
SYSRSTn
JT_RSTn
Figure 4: 88F6192 Pin Map Top View
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
88F6192
Top View
JT_CLK
VDD
VSS
VDD
CPU_PLL_AVDD
VDD
VDDO
MPP[17]
MPP[16]
MPP[14]
MPP[15]
MPP[12]
MPP[13]
VDDO
NF_WEn
NF_REn
NF_CLE
NF_CEn
NF_ALE
MPP[19]
MPP[18]
VSS
MPP[5]
MPP[4]
VSS
MPP[0]
MPP[3]
MPP[1]
MPP[2]
VDDO
MPP[9]
MPP[8]
VSS
MPP[7]
MPP[11]
MPP[6]
MPP[10]
VDD
VSS
SATA0_T_P
VSS
SATA0_T_N
SATA0_AVDD
SATA0_R_N
SATA0_R_P
VDD
SATA1_T_P
VSS
SATA1_T_N
SATA1_AVDD
SATA1_R_N
SATA1_R_P
VSS
VDD
1
VDD_M
2
M_DM[1]
3
M_DQS[1]
4
M_DQSn[1]
5
VDD_M
6
M_DQ[15]
7
M_DQ[8]
8
VDD_M
9
M_DQ[10]
10
M_DQ[13]
11
VSS
12
VDD
USB_AVDD 13
14
USB_DP
15
USB_DM
16
VDD
17
VHV
VDD_GE_A 18
19
GE_TXD[3]
20
GE_TXD[2]
21
GE_TXD[1]
22
GE_TXD[0]
23
GE_TXCTL
GE_TCLKOUT24
VDD_GE_A 25
GE_RXCLK 26
GE_RXCTL 27
GE_RXD[0]
28
GE_RXD[1]
29
GE_RXD[2]
30
GE_RXD[3]
31
VSS
32
GE_MDC
33
GE_MDIO
34
VSS
35
MPP[28]
36
MPP[29]
37
MPP[34]
38
MPP[35]
39
VDD_GE_B 40
MPP[23]
41
MPP[22]
42
MPP[20]
43
MPP[21]
44
MPP[33]
45
MPP[32]
46
VDD_GE_B 47
MPP[31]
48
MPP[30]
49
MPP[24]
50
MPP[25]
51
MPP[26]
52
MPP[27]
53
VDD
54
M_ODT[0]
M_CSn[1]
M_RASn
M_CSn[0]
VDD_M
M_CASn
M_A[0]
M_A[2]
M_A[4]
VDD_M
M_A[6]
M_A[8]
M_A[13]
M_A[11]
VDD_M
VDD
M_DQ[5]
M_DQ[0]
VDD_M
M_DQ[2]
M_DQ[7]
VDD_M
M_DQS[0]
M_DQSn[0]
M_DM[0]
VDD_M
M_DQ[6]
M_DQ[1]
VDD_M
M_DQ[3]
M_DQ[4]
VDD
VDD_M
M_A[9]
M_A[12]
M_A[5]
M_A[7]
VDD_M
M_A[1]
M_A[3]
M_BA[1]
M_A[10]
VDD_M
M_BA[2]
M_WEn
M_BA[0]
M_CKE
VDD_M
VDD
M_DQ[12]
M_DQ[11]
VDD_M
M_DQ[14]
M_DQ[9]
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 59
88F619x
Hardware Specifications
Table 28: 88F6192 Pinout Sorted by Pin Number
Pin # Pin Nam e
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
VDD_M
M_DM[1]
M_DQS[1]
M_DQSn[1]
VDD_M
M_DQ[15]
M_DQ[8]
VDD_M
M_DQ[10]
M_DQ[13]
VSS
VDD
USB_AVDD
USB_DP
USB_DM
VDD
VHV
VDD_GE_A
GE_TXD[3]
GE_TXD[2]
GE_TXD[1]
GE_TXD[0]
GE_TXCTL
GE_TCLKOUT
VDD_GE_A
GE_RXCLK
GE_RXCTL
GE_RXD[0]
GE_RXD[1]
GE_RXD[2]
GE_RXD[3]
VSS
GE_MDC
GE_MDIO
VSS
MPP[28]
MPP[29]
MPP[34]
MPP[35]
VDD_GE_B
MPP[23]
MPP[22]
MPP[20]
MPP[21]
MPP[33]
Pin # Pin Nam e
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
Pin # Pin Nam e
MPP[32]
VDD_GE_B
MPP[31]
MPP[30]
MPP[24]
MPP[25]
MPP[26]
MPP[27]
VDD
VDD
VSS
SATA1_R_P
SATA1_R_N
SATA1_AVDD
SATA1_T_N
VSS
SATA1_T_P
VDD
SATA0_R_P
SATA0_R_N
SATA0_AVDD
SATA0_T_N
VSS
SATA0_T_P
VSS
VDD
MPP[10]
MPP[6]
MPP[11]
MPP[7]
VSS
MPP[8]
MPP[9]
VDDO
MPP[2]
MPP[1]
MPP[3]
MPP[0]
VSS
MPP[4]
MPP[5]
VSS
MPP[18]
MPP[19]
NF_ALE
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
NF_CEn
NF_CLE
NF_REn
NF_WEn
VDDO
MPP[13]
MPP[12]
MPP[15]
MPP[14]
MPP[16]
MPP[17]
VDDO
VDD
CPU_PLL_AVDD
VDD
VSS
VDD
JT_CLK
JT_RSTn
SYSRSTn
VDDO
JT_TMS_CPU
JT_TDO
JT_TMS_CORE
JT_TDI
SSCG_AVDD
VDD
VSS
VDD
VSS
VDD
VSS
VDD
VDD
VSS
VDD
VSS
VDD
VSS
VDD
ISET
XTAL_AVSS
XTAL_AVDD
REF_CLK_XIN
XOUT
Pin # Pin Nam e
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
Doc. No. MV-S104987-U0 Rev. F
Page 60
Pin # Pin Nam e
VDD
CORE_PLL_AVDD
PEX_ISET
VSS
PEX_TX_N
VSS
PEX_TX_P
PEX_AVDD
PEX_RX_N
PEX_RX_P
TP
PEX_CLK_N
PEX_CLK_P
PEX_AVDD
RTC_AVDD
RTC_XIN
RTC_XOUT
VSS
M_PCAL
M_STARTBURST_IN
VDD
M_NCAL
M_STARTBURST
VDD_M
M_CLKOUTn
M_CLKOUT
VDD_M
M_ODT[0]
M_CSn[1]
M_RASn
M_CSn[0]
VDD_M
M_CASn
M_A[0]
M_A[2]
M_A[4]
VDD_M
M_A[6]
M_A[8]
M_A[13]
M_A[11]
VDD_M
VDD
M_DQ[5]
M_DQ[0]
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
VDD_M
M_DQ[2]
M_DQ[7]
VDD_M
M_DQS[0]
M_DQSn[0]
M_DM[0]
VDD_M
M_DQ[6]
M_DQ[1]
VDD_M
M_DQ[3]
M_DQ[4]
VDD
VDD_M
M_A[9]
M_A[12]
M_A[5]
M_A[7]
VDD_M
M_A[1]
M_A[3]
M_BA[1]
M_A[10]
VDD_M
M_BA[2]
M_WEn
M_BA[0]
M_CKE
VDD_M
VDD
M_DQ[12]
M_DQ[11]
VDD_M
M_DQ[14]
M_DQ[9]
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Pin Multiplexing
Multi-Purpose Pins Functional Summary
6
Pin Multiplexing
6.1
Multi-Purpose Pins Functional Summary
The 88F6190/88F6192 device contains 36 Multi-Purpose Pins (MPP). Each one can be assigned to
a different functionality through the MPP Control register.
„
General Purpose pins: MPP[5:0] and MPP[35:7]:
• GPIO (input/output): MPP[0], MPP[4], MPP[9:8], MPP[11], MPP[17:13], MPP[32:20], and
MPP[35:34]
• GPO (output): MPP[3:1], MPP[5], MPP[7], MPP[10], MPP[12], MPP[19:18], and MPP[33]
„
SYSRST_OUTn: Reset request from the device to the board reset logic. This pin is an output.
SYSRST_OUTn is the default setting for MPP[6].
PEX_RST_OUTn: Optional PCI Express Endpoint card reset output.
MII/MMII/GMII/RGMII interface signals
For the 88F6190 only, SATA_ACTn/SATA_PRESENTn: SATA active and SATA present
indications—see the SATA section in the 88F6180, 88F6190, 88F6192, and 88F6281
Functional Specifications.
For the 88F6192 only, SATA0/1_ACTn/SATA0/1_PRESENTn (port 0 and port 1): SATA active
and SATA present indications—see the SATA section in the 88F6180, 88F6190, 88F6192, and
88F6281 Functional Specifications.
NF_IO[7:0] (NAND Flash data [7:0])
SPI interface: SPI_MOSI, SPI_MISO, SPI_SCK, SPI_CSn
UART interface (port 0 and port 1): Transmit and receive functions: UA0_TXD, UA0_RXD,
UA1_TXD, UA1_RXD, and Modem control functions: UA0_RTSn, UA0_CTSn, UA1_RTSn,
UA1_CTSn
SDIO interface: SD_CLK, SD_CMD, SD_D[3:0]
For the 88F6192 only, Audio interface signals: AU_SPDIFI, AU_SPDIFO, AU_SPDIFRMCLK,
AU_I2SBCLK, AU_I2SDO, AU_I2SLRCLK, AU_I2SMCLK, AU_I2SDI, AU_EXTCLK
TS (Transport Stream) interface signals (88F6192 only): TSMP[12:0]
TDM/SPI interface signals (88F6192 only): TDM_CH0/2_TX_QL, TDM_CH0/2_RX_QL,
TDM_SPI_CS0/1, TDM_SPI_SCK, TDM_SPI_MOSI, TDM_SPI_MISO, TDM_CODEC_INTn,
TDM_CODEC_RSTn, TDM_PCLK, TDM_FS, TDM_DRX, TDM_DTX
PTP signals: PTP_EVENT_REQ, PTP_TRIG_GEN, PTP_CLK
„
TWSI signals: TW_SDA, TW_SCK
„
„
„
„
„
„
„
„
„
„
„
„
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 61
88F619x
Hardware Specifications
MPP pins can be assigned to different functionalities through the MPP Control register, as shown in
Table 29.
Table 29: MPP Functionality
MPP[19:0]
MPP[35:20]
GPIO
GPIO
SATA LEDs
SATA LEDs
NAND flash
GbE
TWSI
Audio (88F6192 only)
UART
TDM (88F6192 only)
SPI
TS (88F6192 only)
PTP
PTP
SDIO
Table 30 and Table 31 lists the functionality of the MPP pins, as determined by the MPP Multiplex
register, see the Pins Multiplexing Interface Registers section in the 88F6180, 88F6190, 88F6192,
and 88F6281 Functional Specifications.
Doc. No. MV-S104987-U0 Rev. F
Page 62
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Pin Multiplexing
Multi-Purpose Pins Functional Summary
Table 30: 88F6190 MPP Function Summary
Pin name
0x0
0x1
0x2
0x3
0x4
0x5
0xC
0xD
MPP[0]
GPIO[0]
(in/out)
NF_IO[2]
(in/out)
SPI_SCn
(out)
-
-
-
-
-
MPP[1]
GPO[1] (out
only)
NF_IO[3]
(in/out)
SPI_MOSI
(out)
-
-
-
-
-
MPP[2]
GPO[2] (out
only)
NF_IO[4]
(in/out)
SPI_SCK
(out)
-
-
-
-
-
MPP[3]
GPO[3] (out
only)
NF_IO[5]
(in/out)
SPI_MISO
(in)
-
-
-
-
-
MPP[4]
GPIO[4]
(in/out)
NF_IO[6]
(in/out)
UA0_RXD
(in)
-
-
-
-
PTP_CLK
(in)
MPP[5]
GPO[5] (out
only)
NF_IO[7]
(in/out)
UA0_TXD
(out)
-
-
-
MPP[6]
-
MPP[7]
SYSRST_O SPI_MOSI PTP_TRIG_
UTn (out)
(out)
GEN (out)
GPO[7] (out PEX_RST_
only)
OUTn (out)
PTP_TRIG_ SATA_ACT
GEN (out)
n (out)
-
-
-
-
SPI_SCn
(out)
PTP_TRIG_
GEN (out)
-
-
-
-
-
PTP_CLK
(in)
MII0_COL
(in)
MPP[8]
GPIO[8]
(in/out)
TW_SDA
(in/out)
UA0_RTS
(out)
UA1_RTS
(out)
MII0_RXER
R (in)
MPP[9]
GPIO[9]
(in/out)
TW_SCK
(in/out)
UA0_CTS
(in)
UA1_CTS
(in)
-
MPP[10]
GPO [10]
(out only)
-
SPI_SCK
(out)
UA0_TXD
(out)
-
MPP[11]
GPIO[11]
(in/out)
-
SPI_MISO
(in)
UA0_RXD PTP_EVEN SATA_ACT PTP_TRIG_
(in)
T_REQ (in)
n (out)
GEN (out)
MPP[12]
GPO[12]
(out only)
SD_CLK
(out)
-
-
-
-
-
-
MPP[13]
GPIO[13]
(in/out)
SD_CMD
(in/out)
-
UA1_TXD
(out)
-
-
-
-
MPP[14]
GPIO[14]
(in/out)
SD_D[0]
(in/out)
-
UA1_RXD
(in)
-
-
-
MII0_COL
(in)
MPP[15]
GPIO[15]
(in/out)
SD_D[1]
(in/out)
UA0_RTS
(out)
UA1_TXD
(out)
SATA_ACT
n (out)
-
-
-
MPP[16]
GPIO[16]
(in/out)
SD_D[2]
(in/out)
UA0_CTS
(in)
UA1_RXD
(in)
-
-
-
MII0_CRS
(in)
MPP[17]
GPIO[17]
(in/out)
SD_D[3]
(in/out)
-
-
SATA_PRE
SE NTn
(out)
-
-
-
SATA_PRE
PTP_EVEN MII0_CRS
SE NTn
T_REQ (in)
(in)
(out)
-
Copyright © 2008 Marvell
December 2, 2008, Preliminary
PTP_TRIG_
GEN (out)
PTP_clk
(in)
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 63
88F619x
Hardware Specifications
Table 30: 88F6190 MPP Function Summary (Continued)
Pin name
0x0
0x1
0x2
0x3
0x4
0x5
0xC
0xD
MPP[18]
GPO[18]
(out only)
NF_IO[0]
(in/out)
-
-
-
-
-
-
MPP[19]
GPO[19]
(out only)
NF_IO[1]
(in/out)
-
-
-
-
-
-
MPP[20]
GPIO[20]
(in/out)
-
-
GE1[0]
-
-
-
-
MPP[21]
GPIO[21]
(in/out)
-
-
GE1[1]
-
SATA_ACT
n (out)
-
-
MPP[22]
GPIO[22]
(in/out)
-
-
GE1[2]
-
-
-
-
MPP[23]
GPIO[23]
(in/out)
-
-
GE1[3]
-
SATA_PRE
SE NTn
(out)
-
-
MPP[24]
GPIO[24]
(in/out)
-
-
GE1[4]
-
-
-
-
MPP[25]
GPIO[25]
(in/out)
-
-
GE1[5]
-
-
-
-
MPP[26]
GPIO[26]
(in/out)
-
-
GE1[6]
-
-
-
-
MPP[27]
GPIO[27]
(in/out)
-
-
GE1[7]
-
-
-
-
MPP[28]
GPIO[28]
(in/out)
-
-
GE1[8]
-
-
-
-
MPP[29]
GPIO[29]
(in/out)
-
-
GE1[9]
-
-
-
-
MPP[30]
GPIO[30]
(in/out)
-
-
GE1[10]
-
-
-
-
MPP[31]
GPIO[31]
(in/out)
-
-
GE1[11]
-
-
-
-
MPP[32]
GPIO[32]
(in/out)
-
-
GE1[12]
-
-
-
-
MPP[33]
GPO[33]
(out only)
-
-
GE1[13]
-
-
-
-
MPP[34]
GPIO[34]
(in/out)
-
-
GE1[14]
-
-
-
-
MPP[35]
GPIO[35]
(in/out)
-
-
GE1[15]
-
SATA_ACT MII0_RXER
n (out)
R (in)
Doc. No. MV-S104987-U0 Rev. F
Page 64
-
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Pin Multiplexing
Multi-Purpose Pins Functional Summary
Table 31: 88F6192 MPP Function Summary
Pin name
0x0
0x1
0x2
0x3
0x4
0x5
0xC
0xD
MPP[0]
GPIO[0]
(in/out)
NF_IO[2]
(in/out)
SPI_SCn
(out)
-
-
-
-
-
MPP[1]
GPO[1] (out
only)
NF_IO[3]
(in/out)
SPI_MOSI
(out)
-
-
-
-
-
MPP[2]
GPO[2] (out
only)
NF_IO[4]
(in/out)
SPI_SCK
(out)
-
-
-
-
-
MPP[3]
GPO[3] (out
only)
NF_IO[5]
(in/out)
SPI_MISO
(in)
-
-
-
-
-
MPP[4]
GPIO[4]
(in/out)
NF_IO[6]
(in/out)
UA0_RXD
(in)
-
-
SATA1_AC
Tn (out)
-
PTP_CLK
(in)
MPP[5]
GPO[5] (out
only)
NF_IO[7]
(in/out)
UA0_TXD
(out)
-
PTP_TRIG_ SATA0_AC
GEN (out)
Tn (out)
-
-
MPP[6]
-
MPP[7]
SYSRST_O SPI_MOSI PTP_TRIG_
UTn (out)
(out)
GEN (out)
GPO[7] (out PEX_RST_
only)
OUTn (out)
-
-
-
-
-
-
-
SPI_SCn
(out)
PTP_TRIG_
GEN (out)
-
SATA1_PR
PTP_CLK MII0_COL
ESE NTn
(in)
(in)
(out)
SATA0_PR
PTP_EVEN MII0_CRS
ESE NTn
T_REQ (in)
(in)
(out)
MPP[8]
GPIO[8]
(in/out)
TW_SDA
(in/out)
UA0_RTS
(out)
UA1_RTS
(out)
MII0_RXER
R (in)
MPP[9]
GPIO[9]
(in/out)
TW_SCK
(in/out)
UA0_CTS
(in)
UA1_CTS
(in)
-
MPP[10]
GPO [10]
(out only)
-
SPI_SCK
(out)
UA0_TXD
(out)
-
MPP[11]
GPIO[11]
(in/out)
-
SPI_MISO
(in)
UA0_RXD PTP_EVEN SATA0_AC PTP_TRIG_
(in)
T_REQ (in)
Tn (out)
GEN (out)
MPP[12]
GPO[12]
(out only)
SD_CLK
(out)
-
-
-
-
-
-
MPP[13]
GPIO[13]
(in/out)
SD_CMD
(in/out)
-
UA1_TXD
(out)
-
-
-
-
MPP[14]
GPIO[14]
(in/out)
SD_D[0]
(in/out)
-
UA1_RXD
(in)
SATA1_PR
ESE NTn
(out)
-
-
MII0_COL
(in)
MPP[15]
GPIO[15]
(in/out)
SD_D[1]
(in/out)
UA0_RTS
(out)
UA1_TXD
(out)
SATA0_AC
Tn (out)
-
-
-
MPP[16]
GPIO[16]
(in/out)
SD_D[2]
(in/out)
UA0_CTS
(in)
UA1_RXD
(in)
SATA1_AC
Tn (out)
-
-
MII0_CRS
(in)
MPP[17]
GPIO[17]
(in/out)
SD_D[3]
(in/out)
-
-
SATA0_PR
ESE NTn
(out)
-
-
-
SATA1_AC PTP_TRIG_
Tn (out)
GEN (out)
Copyright © 2008 Marvell
December 2, 2008, Preliminary
PTP_clk
(in)
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 65
88F619x
Hardware Specifications
Table 31: 88F6192 MPP Function Summary (Continued)
Pin name
0x0
0x1
0x2
0x3
0x4
0x5
0xC
0xD
MPP[18]
GPO[18]
(out only)
NF_IO[0]
(in/out)
-
-
-
-
-
-
MPP[19]
GPO[19]
(out only)
NF_IO[1]
(in/out)
-
-
-
-
-
-
MPP[20]
GPIO[20]
(in/out)
TSMP[0]
(in/out)
TDM_CH0_
TX_QL (out)
GE1[0]
AU_SPDIFI SATA1_AC
(in)
Tn (out)
-
-
MPP[21]
GPIO[21]
(in/out)
TSMP[1]
(in/out)
TDM_CH0_
RX_QL (out)
GE1[1]
AU_SPDIF SATA0_AC
O (out)
Tn (out)
-
-
MPP[22]
GPIO[22]
(in/out)
TSMP[2]
(in/out)
TDM_CH2_
TX_QL (out)
GE1[2]
-
-
MPP[23]
GPIO[23]
(in/out)
TSMP[3]
(in/out)
TDM_CH2_
RX_QL (out)
GE1[3]
-
-
MPP[24]
GPIO[24]
(in/out)
TSMP[4]
(in/out)
TDM_SPI_
CS0 (out)
GE1[4]
AU_I2SDO
(out)
-
-
-
MPP[25]
GPIO[25]
(in/out)
TSMP[5]
(in/out)
TDM_SPI_
SCK (out)
GE1[5]
AU_I2SLRC
LK (out)
-
-
-
MPP[26]
GPIO[26]
(in/out)
TSMP[6]
(in/out)
TDM_SPI_
MISO (in)
GE1[6]
AU_I2SMC
LK (out)
-
-
-
MPP[27]
GPIO[27]
(in/out)
TSMP[7]
(in/out)
TDM_SPI_
MOSI (out)
GE1[7]
AU_I2SDI
(in)
-
-
-
MPP[28]
GPIO[28]
(in/out)
TSMP[8]
(in/out)
GE1[8]
AU_EXTCL
K (in)
-
-
-
MPP[29]
GPIO[29]
(in/out)
TSMP[9]
(in/out)
GE1[9]
-
-
-
-
MPP[30]
GPIO[30]
(in/out)
TSMP[10] TDM_PCLK
(in/out)
(in/out)
GE1[10]
-
-
-
-
MPP[31]
GPIO[31]
(in/out)
TSMP[11]
(in/out)
TDM_FS
(in/out)
GE1[11]
-
-
-
-
MPP[32]
GPIO[32]
(in/out)
TSMP[12]
(in/out)
TDM_DRX
(in)
GE1[12]
-
-
-
-
MPP[33]
GPO[33]
(out only)
-
TDM_DTX
(out)
GE1[13]
-
-
-
-
MPP[34]
GPIO[34]
(in/out)
-
TDM_SPI_
CS1 (out)
GE1[14]
-
SATA1_AC
Tn (out)
-
-
MPP[35]
GPIO[35]
(in/out)
-
TDM_CH0_
TX_QL (out)
GE1[15]
-
SATA0_AC MII0_RXER
Tn (out)
R (in)
TDM_COD
EC_INTn
(in)
TDM_COD
EC_RSTn
(out)
AU_SPDIF SATA1_PR
RMCLK(out ESENTn
)
(out)
SATA0_PR
AU_I2SBCL
ESENTn
K (out)
(out)
Doc. No. MV-S104987-U0 Rev. F
Page 66
-
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Pin Multiplexing
Multi-Purpose Pins Functional Summary
„
Note
For MPPs assigned as NAND flash and SPI flash, wake-up mode after reset
depends on Boot mode (see the Boot Device field in Table 38, Reset
Configuration, on page 77):
• When Boot mode is NAND Flash, MPP[5:0] and MPP[19:18] wake up after reset
in NAND Flash mode.
• When Boot mode is SPI Flash, either MPP[3:0] or {MPP[3:1] and MPP[7]} wake
„
„
up after reset in SPI mode, (according to boot mode configured by reset strap
pins).
Pin MPP[6] wakes up after reset in 0x1 mode (SYSRST_OUTn)
Pin MPP[7] wakes up after reset:
• As SPI_CSn, if the boot device—selected according to boot device reset
strapping—is 0x2 (boot from SPI flash, SPI_CSn on MPP[7]).
• As PEX_RST_OUTn, if the boot device—selected according to boot device
„
„
„
reset strapping—is any option other than 0x2.
When TWSI serial ROM initialization is enabled (see TWSI Serial ROM
Initialization in Table 38, Reset Configuration, on page 77), MPP[8] and MPP[9]
wake up as TWSI data and clock pins, respectively.
All other MPP interface pins wake up after reset in 0x0 mode (GPIO/GPO) and are
default set to Data Output disabled (Tri-State). Therefore, those MPPs that are
GPIO are in fact inputs, and those that are GPO are Tri-State.
The SPI interface can be configured using one of the following sets of MPP pins:
• MPP[3:0]
• MPP[11], MPP[10], MPP[7], and MPP[6]
• MPP[3:1] and MPP[7]
„
„
„
„
Do not configure both MPP[3] and MPP[11] as SPI_MISO.
UART0 and UART1 signals are duplicated on a few MPPs. The UART0 or UART1
signals must not be configured to more than one MPP.
Some of the MPP pins are sampled during SYSRSTn de-assertion to set the
device configuration. These pins must be set to the correct value during reset (see
Section 8.5, Pins Sample Configuration, on page 76).
Pins that are left as GPIO and are not connected should be set to output after
SYSRSTn de-assertion.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 67
88F619x
Hardware Specifications
6.2
Gigabit Ethernet (GbE) Pins Multiplexing on MPP
88F6190
Contains 14 dedicated pins for its GbE port (12 GMII pins, an MDC pin, and an
MDIO pin).
Includes additional GbE interface pins that are multiplexed on the MPPs, to serve
as the remaining pin interfaces to an external PHY or switch:
„
RGMII
„
MII/MMII
„
GMII
88F6192
Contains 14 dedicated pins for its GbE ports. (12 RGMII/GMII pins, an MDC pin,
and an MDIO pin).
Includes additional GbE interface pins that are multiplexed on the MPPs, to serve
as the following interfaces to an external PHY or switch:
„
GMII
„
2 x RGMII
„
RGMII + MII/MMII
Table 32 summarizes the GbE port pins multiplexing for the 88F6190.
Table 32: 88F6190 Ethernet Ports Pins Multiplexing
Pin Name
GMII
RGMI I0 +MII 1/ MMI I 1
GE_TXCLKOUT
GMII_TXCLKOUT (out)
RGMII0_TXCLKOUT (out)
GE_TXD[3:0]
GMII_TXD[3:0] (out)
RGMII0_TXD[3:0] (out)
GE_TXCTL
GMII_TXEN (out)
RGMII0_TXCTL (out)
GE_RXD[3:0]
GMII_RXD[3:0] (in)
RGMII0_RXD[3:0] (in)
GE_RXCTL
GMII_RXDV (in)
RGMII0_RXCTL (in)
GE_RXCLK
GMII_RXCLK (in)
RGMII0_RXCLK (in)
MPP [23:20] / GE1[3:0]
GMII_TXD[7:4] (out)
MII1_TXD[3:0] (out)
MPP_[27:24] / GE1[7:4]
GMII_RXD[7:4] (in)
MII1_RXD[3:0] (in)
MPP_28 / GE1[8]
GMII_COL (in)
MII1_COL (in)
MPP_29 / GE1[9]
GMII_TXCLK (in)
MII1_TXCLK (in)
MPP_30 / GE1[10]
GMII_RXERR (in)
MII1_RXDV (in)
MPP_31 / GE1[11]
NA
MII1_RXCLK (in)
MPP_32 / GE1[12]
GMII_CRS (in)
MII1_CRS (in)
MPP_33 / GE1[13]
GMII_TXERR (out)
MII1_TXERR (out)
MPP_34 / GE1[14]
NA
MII1_TXEN (out)
MPP_35 / GE1[15]
NA
MII1_RXERR (in)
Doc. No. MV-S104987-U0 Rev. F
Page 68
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Pin Multiplexing
Gigabit Ethernet (GbE) Pins Multiplexing on MPP
Table 33 summarizes the GbE port pins multiplexing for the 88F6192.
Table 33: 88F6192 Ethernet Ports Pins Multiplexing
Pin Name
1x GMII
RGMII0 +MII1/
MM I I1
2x RGMII
MII0/MMII0+
R GM I I1
GE_TXCLKOUT
GMII0_TXCLKOUT
(out)
RGMII0_TXCLKOUT
(out)
RGMII0_TXCLKOUT
(out)
MII0_TXCLK (in)
GE_TXD[3:0]
GMII0_TXD[3:0] (out)
RGMII0_TXD[3:0]
(out)
RGMII0_TXD[3:0]
(out)
MII0_TXD[3:0] (out)
GE_TXCTL
GMII0_TXEN (out)
RGMII0_TXCTL (out)
RGMII0_TXCTL (out)
MII0_TXEN (out)
GE_RXD[3:0]
GMII0_RXD[3:0] (in)
RGMII0_RXD[3:0] (in)
RGMII0_RXD[3:0] (in)
MII0_RXD[3:0] (in)
GE_RXCTL
GMII0_RXDV (in)
RGMII0_RXCTL (in)
RGMII0_RXCTL (in)
MII0_RXDV (in)
GE_RXCLK
GMII0_RXCLK (in)
RGMII0_RXCLK (in)
RGMII0_RXCLK (in)
MII0_RXCLK (in)
MPP[8] or
MPP[35]
NA
NA
NA
MII0_RXERR (in)
MPP[8] or
MPP[14]
NA
NA
NA
MII0_COL (in)
MPP[9] or
MPP[16]
NA
NA
NA
MII0_CRS (in)
MPP [23:20] /
GE1[3:0]
GMII0_TXD[7:4] (out)
MII1_TXD[3:0] (out)
RGMII1_TXD[3:0]
(out)
RGMII1_TXD[3:0]
(out)
MPP_[27:24] /
GE1[7:4]
GMII0_RXD[7:4] (in)
MII1_RXD[3:0] (in)
RGMII1_RXD[3:0] (in)
RGMII1_RXD[3:0] (in)
MPP_28 /
GE1[8]
GMII0_COL (in)
MII1_COL (in)
NA
NA
MPP_29 /
GE1[9]
GMII0_TXCLK (in)
MII1_TXCLK (in)
NA
NA
MPP_30 /
GE1[10]
GMII0_RXERR (in)
MII1_RXDV (in)
RGMII1_RXCTL (in)
RGMII1_RXCTL (in)
MPP_31 /
GE1[11]
NA
MII1_RXCLK (in)
RGMII1_RXCLK (in)
RGMII1_RXCLK (in)
MPP_32 /
GE1[12]
GMII0_CRS (in)
MII1_CRS (in)
RGMII1_TXCLKOUT
(out)
RGMII1_TXCLKOUT
(out)
MPP_33 /
GE1[13]
GMII0_TXERR (out)
MII1_TXERR (out)
RGMII1_TXCTL (out)
RGMII1_TXCTL (out)
MPP_34 /
GE1[14]
NA
MII1_TXEN (out)
NA
NA
MPP_35 /
GE1[15]
NA
MII1_RXERR (in)
NA
NA
Note
When using Gigabit Ethernet signals on MPPs, all relevant Gigabit Ethernet signals
(except those marked as NA) must be implemented. For example, if using MII, and the
chosen PHY does not have an MII_RXERR out signal, the MII_RX_ERR (in) (MPP[35])
must still be configured accordingly and must have a pull-down resistor.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 69
88F619x
Hardware Specifications
6.3
TSMP (TS Multiplexing Pins) on MPP
The TSMP multiplexing information is only relevant for the 88F6192.
Note
The TS interface can be configured to one of five modes:
„
One or two serial in interfaces
„
One or two serial out interfaces
„
Serial in and serial out interface
„
Parallel in interface
„
Parallel out interface
In parallel in or serial in mode, all TS signals are inputs.
In parallel out or serial out mode, all TS signals are outputs.
Table 34 summarizes the TS port pins multiplexing.
Table 34: TS Port Pin Multiplexing
Pin
Name
Fu nc t io na li t y in TS s e r i a l m od e s
2x in/2x o ut/in + ou t
F un c t i on a l ity i n TS pa r a l le l
i n/ o ut m od e
TSMP[0]
EXT_CLK (in)
EXT_CLK (in)
TSMP[1]
TS0_CLK (in/out))
TS0_CLK (in/out))
TSMP[2]
TS0_SYNC(in/out))
TS0_SYNC(in/out))
TSMP[3]
TS0_VAL (in/out))
TS0_VAL (in/out))
TSMP[4]
TS0_ERR (in/out))
TS0_ERR (in/out))
TSMP[5]
TS0_DATA[0] (in/out)
TS0_DATA[0] (in/out)
TSMP[6]
TS1_CLK (in/out))
TS0_DATA[1] (in/out))
TSMP[7]
TS1_SYNC(in/out))
TS0_DATA[2] (in/out))
TSMP[8]
TS1_VAL (in/out))
TS0_DATA[3] (in/out))
TSMP[9]
TS1_ERR (in/out))
TS0_DATA[4] (in/out))
TSMP[10]
TS1_DATA[0] (in/out)
TS0_DATA[5] (in/out))
TSMP[11]
NA
TS0_DATA[6] (in/out))
TSMP[12]
NA
TS0_DATA[7] (in/out))
Doc. No. MV-S104987-U0 Rev. F
Page 70
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Clocking
7
Clocking
Table 35 lists the clocks in the 88F619x.
Table 35: 88F619x Clocks
C l o ck Ty p e
Description
CPU PLL
•
Reference clock:
REF_CLK_XIN (25 MHz)
• Derivative clocks:
- CPU clock
- L2 cache clock
- DDR Clock (the Mbus-L uses the DDR clock.)
NOTE: See Table 38, Reset Configuration, on page 77 for CPU, L2 cache and
DDR frequency configuration.
L2 cache clock frequency must be equal or higher then DDR clock
frequency.
If the SSCG enable bit in the Sampled at Reset register is set, then the
SSCG circuit is applied for the CPU PLL reference clock (refer to the
Sampled at Reset register in the 88F6180, 88F6190, 88F6192, and
88F6281 Functional Specifications).
Core PLL
•
Reference clock:
REF_CLK_XIN (25 MHz)
• Derivative clocks:
- TCLK (core clock, 166 MHz)
- SDIO Clock (100 MHz)
- Gigabit Ethernet Clock (125 MHz)
- TS unit Clock(100/91/83/77MHz) (88F6192 only)
- SPI clock (TCLK/30–TCLK/4 MHz)
- SMI clock (TCLK/128 MHz)
- TWSI clock (up to TCLK/1600)
NOTE: See Table 38, Reset Configuration, on page 77 for TCLK frequency
configuration.
NOTE: See the TS Interface Configuration register in the 88F6180, 88F6190,
88F6192, and 88F6281 Functional Specifications for TS clock frequency
configuration (88F6192 only).
PEX PHY
There are two options for the reference clock configuration, depending on the PCI
Express clock 100 MHz differential clock:
• The device uses an external source for PCI Express clock. The PEX_CLK_P
pin is an input.
• The device uses an internal generated clock for PCI Express clock. The
PEX_CLK_P pin is an output, driving out the PCI Express differential clock.
USB PHY PLL
•
Reference clock:
REF_CLK_XIN (25 MHz)
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 71
88F619x
Hardware Specifications
Table 35: 88F619x Clocks (Continued)
C l o ck Ty p e
Description
SATA PHY PLL
•
•
Reference clock:
REF_CLK_XIN (25 MHz)
Derivative clock:
SATA Clock (150 MHz)
RTC
•
Reference clock:
RTC_XIN (32.768 kHz)
Used for real time clock functionality, see the Real Time Clock section in the
88F6180, 88F6190, 88F6192, and 88F6281 Functional Specifications.
PTP
•
Reference clock:
PTP_CLK (125 MHz)
The PTP_CLK can be used for the following functions:
• PTP time stamp clock
Two options for reference clock:
- PTP_CLK
- Gigabit Ethernet Clock (125 MHz)
• TS unit clock
Two options for reference clock:
- PTP_CLK/2
- Core PLL
• Audio unit clock
Two options for reference clock:
- PTP_CLK
- REF_CLK_XIN (25 MHz)
For clocking configuration registers, see the 88F6180, 88F6190, 88F6192, and
88F6281 Functional Specifications.
The following table lists the supported combinations of the CPU_CLK Frequency select, CPU_CLK
to DDR CLK ratio, and to CPU_CLK to CPU L2 clock ratio (see Section 8.5, Pins Sample
Configuration, on page 76).
Table 36: Supported Clock Combinations
Device
7.1
DDR Clock
(MHz)
CPU to DDR
C l o c k R at io
C P U C lo c k
(MHz)
C PU t o L 2
C lo c k R a ti o
L 2 C lo c k
(MHz)
88F6190:
200
3:1
600
2:1
300
88F6192:
200
4:1
800
2:1
400
Spread Spectrum Clock Generator (SSCG)
The SSCG (Spread Spectrum Clock Generator) may be used to generate the spread spectrum clock
for the PLL input. See SSCG Disable in Table 38, Reset Configuration, on page 77, for SSCG
enable/bypass configuration settings.
The SSCG block can be configured to perform up spread, down spread and center spread.
The modulation frequency is configurable. Typical frequency is 30 kHz.
The spread percentage can also be configured up to 1%.
For additional details, see the SSCG Configuration Register description in the 88F6180, 88F6190,
88F6192, and 88F6281 Functional Specifications.
Doc. No. MV-S104987-U0 Rev. F
Page 72
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
System Power Up/Down and Reset Settings
Power-Up/Down Sequence Requirements
8
System Power Up/Down and Reset
Settings
This section provides information about the device power-up/down sequence and configuration at
reset.
8.1
Power-Up/Down Sequence Requirements
8.1.1
Power-Up Sequence Requirements
These guidelines must be applied to meet the 88F619x device power-up requirements:
„
The non-core voltages (I/O and Analog) as listed in Table 37 must reach 70% of their voltage
level before the core voltages reach 70% of their voltage level.
The order of the power-up sequence between the non-core voltages is unimportant so long as
the non-core voltages power up before the core voltages reach 70% of their voltage level
(shown in Figure 5).
„
The reset signal(s) must be asserted before the core voltages reach 70% of their voltage level
(shown in Figure 5).
„
The reference clock(s) inputs must toggle with their respective voltage levels before the core
voltages reach 70% of their voltage level (shown in Figure 5).
If VHV is set to burning mode (2.5V), which is a higher voltage than the VDD voltage, VDD must
be powered before VHV, to prevent the fuse from being accidentally burned.
„
Table 37: I/O and Core Voltages
N o n - C o r e Vo lta g e s
I/ O Vo lta ge s
A n a lo g P o w e r Su p pl i es
VDD_GE_A
VDD_GE_B
VDD_M
VDDO
CPU_PLL_AVDD
CORE_PLL_AVDD
PEX_AVDD
RTC_AVDD
88F6190 – SATA_AVDD
88F6192 – SATA0_AVDD
88F6192 – SATA1_AVDD
SSCG_AVDD
XTAL_AVDD
USB_AVDD
Copyright © 2008 Marvell
December 2, 2008, Preliminary
C or e Vo l ta g es
VDD
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 73
88F619x
Hardware Specifications
Figure 5: Power-Up Sequence Example
Voltage
Non-Core Voltage
70% of
Non-Core
Voltage
Core Voltage
70% of Core
Voltage
Reset(s)
Clock(s)
„
Note
8.1.2
„
It is the designer's responsibility to verify that the power sequencing requirements
of other components are also met.
Although the non-core voltages can be powered up any time before the core
voltages, allow a reasonable time limitation (for example, 100 ms) between the
first non-core voltage power-up and the last core voltage power-up.
Power-Down Sequence Requirements
There are no special requirements for the core supply to go down before non-core power, or for
reset assertion when powering down (except for VHV, as described below). However, allow a
reasonable time limitation (no more than 100 ms) between the first and last voltage power-down.
When using the eFuse in Burning mode, VHV must be powered down before VDD.
8.2
Hardware Reset
The device has one reset input pin—SYSRSTn. When asserted, the entire chip is placed in its initial
state. Most outputs are placed in high-z, except for the following output pins, that are still active
during SYSRSTn assertion:
„
M_CLKOUT, M_CLKOUTn
„
M_CKE
„
M_ODT
„
M_STARTBURST
„
SYSRST_OUTn
Doc. No. MV-S104987-U0 Rev. F
Page 74
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
System Power Up/Down and Reset Settings
Hardware Reset
Note
8.2.1
Reset (SYSRSTn signal) must be active for a minimum length of 5 ms. core power, I/O
power, and analog power must be stable (VDD +/- 5%) during that time and onward.
Reset Out Signal
The device has an optional SYSRST_OUTn output signal, multiplexed on an MPP pin, that is used
as a reset request from the device to the board reset logic. SYSRST_OUTn is the default option for
that MPP pin.
This signal is asserted low for 20 ms, when one of the following maskable events occurs:
„
Received hot reset indication from the PCI Express link (only relevant when used as a PCI
Express endpoint), and bit <PexRstOutEn> is set to 1 in the RSTOUTn Mask Register (see the
Reset register section of the 88F6180, 88F6190, 88F6192, and 88F6281 Functional
Specifications).
„
PCI Express link failure (only relevant when used as a PCI Express endpoint), and bit
<PexRstOutEn> is set to 1 in the RSTOUTn Mask Register.
„
Watchdog timer expiration and bit <WDRstOutEn> is set to 1 in the RSTOUTn Mask Register.
„
Bit <SystemSoftRst> is set to 1 in System Soft Reset Register and bit <SoftRstOutEn> is set
to 1 in RSTOUTn Mask Register.
This signal is asserted low for 20 ms, when the POR (power on reset) non-maskable event
occurs.—the device includes a power on reset circuit for VDD power.
8.2.2
Power On Reset (POR)
The SYSRST_OUTn output signal is asserted low for 20 ms, when the power-on-reset (POR) circuit
is triggered.
POR is triggered when VDD power up (digital core voltage) reaches a VDD threshold (threshold
maximum value 0.8V).
Hysteresis: Another trigger will only occur after the power first drops to 50 mV, and then a power up
occurs.
8.2.3
SYSRSTn Duration Counter
When SYSRSTn is asserted low, a SYSRSTn duration counter is running.
„
The counter clock is the 25 MHz reference clock.
„
It is a 29-bit counter, yielding a maximum counting duration of 2^29/25 MHz (21.4 seconds).
„
The host software can read the counter value and reset the counter.
„
When the counter reach its maximum value, it remains at this value until counter reset is
triggered by software.
Note
The SYSRSTn duration counter is useful for implementing manufacturer/factory reset.
Upon a long reset assertion, greater than a pre-configured threshold, the host software
may reset all settings to the factory default values.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 75
88F619x
Hardware Specifications
8.3
PCI Express Reset
8.3.1
PCI Express Root Complex Reset
As a Root Complex, the device may generate a Hot Reset to the PCI Express port. Upon CPU
setting the PCI Express Control register’s <conf_mstr_hot_reset> bit, the PCI Express unit sends a
Hot Reset indication to the Endpoint, see the PCI Express Interface section in the 88F6180,
88F6190, 88F6192, and 88F6281 Functional Specifications.
8.3.2
PCI Express Endpoint Reset
When a Hot Reset packet is received:
„
A maskable interrupt is asserted.
„
If the <conf_dis_hot_rst_reg_rst> field in the PCI Express Debug Control register is cleared, the
device also resets the PCI Express register file to its default values.
„
The device triggers an internal reset, if not masked by the <conf_msk_hot_reset> field in the
PCI Express Debug Control register.
Link failure is detected if the PCI Express link was up (LTTSSM L0 state) and dropped back to an
inactive state (LTSSM Detect state). When Link failure is detected:
„
A maskable interrupt is asserted.
„
If the <conf_dis_link_fail_reg_rst> field in the PCI Express Debug Control register is cleared,
the device also resets the PCI Express register file to its default values.
„
The device triggers an internal reset, if the <conf_msk_link_fail> field is not masked by PCI
Express Debug Control register.
Both link fail and hot reset conditions trigger a chip internal reset (if not masked in the PCI Express
interface). All the chip logic is reset to the default values, except for sticky registers and the sample
on reset logic. In addition, these events can trigger reset to the board, using one of the following:
„
PEX_RST_OUTn signal (multiplexed on MPP).
„
SYSRST_OUTn output (multiplexed on MPP)—if not masked by the <PexRstOutEn> bit.
The external reset logic (on the board) may assert the SYSRSTn input pin and reset the entire chip.
8.4
Sheeva™ CPU TAP Controller Reset
The Sheeva™ CPU Test Access Port (TAP) controller is reset when JT_RSTn is set and
JT_TMS_CPU is active.
8.5
Pins Sample Configuration
The following pins are sampled during SYSRSTn de-assertion:
„
Internal pull up/down resistors set the default mode (see Section 2.3, Internal Pull-up and
Pull-down Pins, on page 55).
„
Higher value, external pull up/down resistors are required to change the default mode of
operation.
These signals must remain pulled up or down until SYSRSTn de-assertion (zero hold time in respect
to SYSRSTn de-assertion).
Doc. No. MV-S104987-U0 Rev. F
Page 76
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
System Power Up/Down and Reset Settings
Pins Sample Configuration
„
Note
„
„
If external logic is used instead of pull-up and pull-down resistors, the logic must
drive all of these signals to the desired values during SYSRSTn assertion. To
prevent bus contention on these pins, the external logic must float the bus no later
than the third TCLK cycle after SYSRSTn de-assertion.
All reset sampled values are registered in the Sample at Reset register (see the
MPP Registers in the 88F6180, 88F6190, 88F6192, and 88F6281 Functional
Specifications). This is useful for board debug purposes and identification of board
and system settings for the host software.
If a signal is pulled up on the board, it must be pulled to the proper voltage level. In
the devices, certain reset configuration pins are powered by VDD_GE_A and
VDD_GE_B. In the 88F6190 VDD_GE_A has multiple voltage options, and in the
88F6192, VDD_GE_A and VDD_GE_B have multiple voltage options (see
Table 42, Recommended Operating Conditions, on page 87).
In each row of Table 38, the order of the pins is from MSb to LSb (e.g., for in the row CPU_CLK
Frequency Select, MPP[2] is the MSB and MPP[10] is the LSB).
Table 38: Reset Configuration
P in
C on fi g ur a tio n F u n ct io n
MPP[1]
TWSI Serial ROM Initialization
0 = Disabled
1 = Enabled
NOTE: Internally pulled down to 0x0.
When this pin is set to 0x1, MPP[8] and MPP[9] wake up as TWSI data and clock pins,
respectively (see Section 6.1, Multi-Purpose Pins Functional Summary, on page 61).
MPP[2],
Used for internal testing
Must be 0x0 during reset.
Either leave the signal floating (internally pulled down to 0x0) or pull the signal to 0x0 during reset.
MPP[5]
Reserved
For the 88F6190:
NOTE: Must be externally pulled down to 0x0 during reset.
For the 88F6192:
Must be 0x1 during reset.
Either leave the signal floating (internally pulled up to 0x1) or pull the signal to 0x1 during reset.
MPP[10]
Used for internal testing
Must be 0x0 during reset.
Either leave the signal floating (internally pulled down to 0x0) or pull the signal to 0x0 during reset.
MPP[19]
Reserved
Must be 0x1 during reset.
Either leave the signal floating (internally pulled up to 0x1) or pull the signal.
MPP[33],
Reserved
Must be 0x0 during reset.
Either leave the signal floating (internally pulled down to 0x0) or pull the signal to 0x0 during reset.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 77
88F619x
Hardware Specifications
Table 38: Reset Configuration (Continued)
P in
C on fi g ur a tio n F u n ct io n
NF_ALE
Reserved
Must be 0x1 during reset.
Either leave the signal floating (internally pulled up to 0x1) or pull the signal to 0x1 during reset.
NF_REn
Reserved
For the 88F6190:
Must be 0x0 during reset.
Either leave the signal floating (internally pulled down to 0x0) or pull the signal to 0x0 during reset.
For the 88F6192:
NOTE: Must be externally pulled up to 0x1 during reset.
NF_CLE
Reserved
Must be 0x0 during reset.
Either leave the signal floating (internally pulled down to 0x0) or pull the signal to 0x0 during reset.
MPP[3]
Reserved
Must be 0x0 during reset.
Either leave the signal floating (internally pulled down to 0x0) or pull the signal to 0x0 during reset.
MPP[12]
Reserved
Must be 0x0 during reset.
Either leave the signal floating (internally pulled down to 0x0) or pull the signal to 0x0 during reset.
NF_WEn
Reserved
Must be 0x1 during reset.
Either leave the signal floating (internally pulled up to 0x1) or pull the signal to 0x1 during reset.
Doc. No. MV-S104987-U0 Rev. F
Page 78
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
System Power Up/Down and Reset Settings
Pins Sample Configuration
Table 38: Reset Configuration (Continued)
P in
C on fi g ur a tio n F u n ct io n
GE_TXD[2:0]
Boot Device
0x0 = Reserved
0x1 = Reserved
0x2 = Boot from SPI flash (SPI_CSn on MPP[7])
0x3 = Reserved
0x4 = Boot from SPI flash (SPI_CSn on MPP[0])
0x5 = Boot from NAND flash
0x6 = Boot from SATA
0x7 = Boot from the PCI Express port
NOTE:
• Internally pulled to 0x4.
• Only SPI signals configured on pins MPP[3:0] or on pins MPP[7] and MPP[3:1] can be used for
booting from SPI.
SPI signals that are multiplexed on other MPPs can only be used after booting (see Section 6.1,
Multi-Purpose Pins Functional Summary, on page 61).
• When GE_TXD[2:0] is set to 0x4, MPP[3:0] wake up as SPI signals.
• When GE_TXD[2:0] is set to 0x2, MPP[7] and MPP[3:1] wake up as SPI signals.
• When GE_TXD[2:0] is set to 0x5, MPP[5:0] and MPP[19:18] wake up as NAND Flash signals.
• For a more detailed description of the bootROM, see the BootROM section in the 88F6180,
88F6190, 88F6192, and 88F6281 Functional Specifications.
• For a more detailed description of the boot from SPI flash or NAND flash, see the SPI Interface
and NAND Flash Interface sections in the 88F6180, 88F6190, 88F6192, and 88F6281 Functional
Specifications.
• There is an option to boot from UART when GE_TXD[2:0] = 0x2–0x7. For a more detailed
description of the boot from UART, see the BootROM section in the 88F6180, 88F6190,
88F6192, and 88F6281 Functional Specifications.
GE_TXD[3]
SSCG Disable
0 = Enable
1 = Disable
NOTE: Internally pulled to 0x1.
GE_MDC
PCI Express Clock (100 MHz Differential Clock) Configuration
0x0 = The device use external source for PCI Express clock. Pins PEX_CLK_P/PEX_CLK_N are
inputs.
0x1 = The device uses internal generated clock for PCI Express clock. Pins
PEX_CLK_P/PEX_CLK_N pins are outputs, driving out the PCI Express differential clock.
NOTE: Internally pulled to 0x1.
88F6190 –
GE_TXEN
88F6192 –
GE_TXCTL
MPP[7]
Used for internal testing
Must be 0x0 during reset. Either leave the signal floating (internally pulled down to 0x0) or pull the signal to
0x0 during reset.
Reserved
Must be 0x1 during reset. Either leave the signal floating (internally pulled up to 0x1) or pull the signal
to 0x1 during reset.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 79
88F619x
Hardware Specifications
Table 38: Reset Configuration (Continued)
P in
C on fi g ur a tio n F u n ct io n
MPP[18]
Reserved
Must be 0x1 during reset. Either leave the signal floating (internally pulled up to 0x1) or pull the signal
to 0x1 during reset.
8.6
Serial ROM Initialization
The device supports initialization of ALL of its internal and configuration registers through the TWSI
master interface. If serial ROM initialization is enabled, the device TWSI master starts reading
initialization data from serial ROM and writes it to the appropriate registers, upon de-assertion of
SYSRSTn.
When using Serial ROM Initialization, the MPP[9:8] pins must be configured to as TW_SCK
(MPP[9]) and TW_SDA (MPP[8]).
8.6.1
Serial ROM Data Structure
Serial ROM data structure consists of a sequence of 32-bit address and 32-bit data pairs, as shown
in Figure 6.
Figure 6: Serial ROM Data Structure
Start
MSB
LSB
address0[31:24]
address0[23:16]
address0[15:8]
address0[7:0]
data0[31:24]
data0[23:16]
data0[15:8]
data0[7:0]
address1[31:24]
address1[23:16]
address1[15:8]
address1[7:0]
data1[31:24]
data1[23:16]
data1[15:8]
data1[7:0]
Doc. No. MV-S104987-U0 Rev. F
Page 80
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
System Power Up/Down and Reset Settings
Boot Sequence
The serial ROM initialization logic reads eight bytes at a time. It performs address decoding on the
32-bit address being read, and based on address decoding result, writes the next four bytes to the
required target.
The Serial Initialization Last Data Register contains the expected value of last serial data item
(default value is 0xFFFFFFFF). When the device reaches last data, it stops the initialization
sequence.
8.6.2
Serial ROM Initialization Operation
On SYSRSTn de-assertion, the device starts the initialization process. It first performs a dummy
write access to the serial ROM, with data byte(s) of 0x0, to set the ROM byte offset to 0x0. Then, it
performs the sequence of reads, until it reaches last data item, as shown in Figure 7.
Figure 7: Serial ROM Read Example
w
r
i
t
e
s
t
a
r
t
s 1 0 1 0 0 0 0 0
0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0
Data from
ROM
r
e
a
d
s 1 0 1 0 0 0 0 1
a
c
k
a
c
k
a
c
k
s
t
a
r
t
Lower Byte Offset
Upper Byte Offset
A A A A A A A A
a
c
k
A A A A
a
c
k
ROM
Address
ROM
Address
Last Data
from ROM
1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1
a
c
k
1 1 1 1 1 1 1 1
a
c
k
s
t
o
p
1 1 1 1 1 1 1 1
a
c
k
x x x x x x x x
a
c
k
p
n
a
c
k
For a detailed description of TWSI implementation, see the Two-Wire Serial Interface section in the
88F6180, 88F6190, 88F6192, and 88F6281 Functional Specifications.
„
„
„
„
8.7
Initialization data must be programmed in the serial ROM starting at offset 0x0.
The device assumes 7-bit serial ROM address of ‘b1010000.
After receiving the last data identifier (default value is 0xFFFFFFFF), the device receives an
additional byte of dummy data. It responds with no-ack and then asserts the stop bit.
The serial EEPROM must contain two address offset bytes (It must not be less than a 256 byte
ROM.).
Boot Sequence
The device requires that SYSRSTn stay asserted for at least 300 μs after power and clocks are
stable. The following procedure describes the boot sequence starting with the reset assertion:
1. While SYSRSTn is asserted, the CPU PLL and the core PLL are locked.
2. Upon SYSRSTn de-assertion, the pad drive auto-calibration process starts. It takes 512 TCLK
cycles.
3. If Serial ROM initialization is enabled, an initialization sequence is started.
4. If configured to boot from NAND flash (and BootROM is disabled), the device also performs a
NAND Flash boot sequence to prepare page 0 in the NAND flash device for read.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 81
88F619x
Hardware Specifications
Upon completing the above sequence, the internal CPU reset is de-asserted, and the CPU starts
executing boot code from the boot device (SPI flash, NAND flash, or internal Boot ROM), according
to sample at reset setting, see Table 38, Reset Configuration, on page 77.
For bootROM details, see the BootROM section in the 88F6180, 88F6190, 88F6192, and 88F6281
Functional Specifications.
As part of the CPU boot code, the CPU typically performs the following:
Configures the PCI Express address map.
„
Configures the proper SDRAM controller parameters, and then triggers SDRAM initialization
(sets <InitEn> bit [0] to 1 in the SDRAM Initialization Control register).
„
Sets the <PEXEn> bits in the CPU Control and Status register to wake up the PCI Express link.
„
Doc. No. MV-S104987-U0 Rev. F
Page 82
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
JTAG Interface
TAP Controller
9
JTAG Interface
To enable board testing, the device supports a test mode operation through its JTAG boundary scan
interface.
The JTAG interface is IEEE 1149.1 standard compliant. It supports mandatory and optional
boundary scan instructions.
9.1
TAP Controller
The Test Access Port (TAP) is constructed with a 5-pin interface and a 16-state Finite State Machine
(FSM), as defined by IEEE JTAG standard 1149.1.
To place the device in a functional mode, reset the JTAG state machine to disable the JTAG
interface.
According to the IEEE 1149.1 standard, the JTAG state machine is not reset when the
88F619xSYSRSTn is asserted. The JTAG state machine can only be reset by one of the following
methods:
„
Asserting JT_RSTn.
„
Setting JT_TMS_CORE for at least five JT_CLK cycles.
To place the device in one of the boundary scan test mode, the JTAG state machine must be moved
to its control states. JT_TMS_CORE and JT_TDI inputs control the state transitions of the JTAG
state machine, as specified in the IEEE 1149.1 standard. The JTAG state machine will shift
instructions into the Instruction register while in SHIFT-IR state and shift data into and from the
various data registers when in SHIFT-DR state.
9.2
Instruction Register
The Instruction register (IR) is a 4-bit, two-stage register. It contains the command that is shifted in
when the TAP FSM is in the Shift-IR state. When the TAP FSM is in the Capture-IR state, the IR
outputs all four bits in parallel.
Table 39 lists the instructions supported by the device.
Table 39: Supported JTAG Instructions
In s t r u c t io n
C o de
D es c r ip t i o n
HIGHZ
0011
Select the single bit Bypass register between TDI and TDO.
Sets the device output pins to high-impedance state.
IDCODE
0010
Selects the Identification register between TDI and TDO. This 32-bit
register is used to identify the device.
EXTEST
0000
Selects the Boundary Scan register between TDI and TDO. Outputs the
boundary scan register cells to drive the output pins of the device. Inputs
the boundary scan register cell to sample the input pin of the device.
SAMPLE/PRE
LOAD
0001
Selects the Boundary Scan register between TDI and TDO. Samples
input pins of the device to input boundary scan register cells.
Preloads the output boundary scan register cells with the Boundary Scan
register value.
BYPASS
1111
Selects the single bit Bypass register between TDI and TDO. This allows
for rapid data movement through an untested device.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 83
88F619x
Hardware Specifications
9.3
Bypass Register
The Bypass register (BR) is a single bit serial shift register that connects TDI to TDO, when the IR
holds the Bypass command, and the TAP FSM is in Shift-DR state. Data that is driven on the TDI
input pin is shifted out one cycle later on the TDO output pin. The Bypass register is loaded with 0
when the TAP FSM is in the Capture-DR state.
9.4
JTAG Scan Chain
The JTAG Scan Chain is a serial shift register used to sample and drive all of the device pins during
the JTAG tests. It is a 2-bit per pin shift register in the device, thereby allowing the shift register to
sequentially access all of the data pins both for driving and strobing data. For further details, refer to
the BSDL Description file for the device.
9.5
ID Register
The ID register is a 32-bit deep serial shift register. The ID register is loaded with vendor and device
information when the TAP FSM is in the Capture-DR state. The Identification code format of the ID
register is shown in Table 40, which describes the various ID Code fields.
Table 40: IDCODE Register Map
B i ts
Va l u e
Description
31:28
0x0
Version (4'b0010 for version A0, 4'b0011 for A1, etc.)
27:12
0x6192
Part number
11:1
0x1AB
Manufacturer ID
0
1
Mandatory
Doc. No. MV-S104987-U0 Rev. F
Page 84
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications (Preliminary)
Absolute Maximum Ratings
10
Electrical Specifications (Preliminary)
The numbers specified in this section are PRELIMINARY and SUBJECT TO CHANGE.
Note
10.1
Absolute Maximum Ratings
Table 41: Absolute Maximum Ratings
Parameter
Min
Max
U n its
C om m e n ts
VDD
-0.5
1.2
V
Core and CPU voltage
CPU_PLL_AVDD
CORE_PLL_AVDD
-0.5
2.2
V
Analog supply for the internal PLL
SSCG_AVDD
-0.5
2.2
V
Analog supply for:
Internal Spread Spectrum Clock Generator
VDD_GE_A
VDD_GE_B
-0.5
4.0
V
I/O voltage for:
RGMII/GMII/MII/MMII/SMI interface
VDD_M
-0.5
2.2
V
I/O voltage for:
SDRAM interface
VDDO
-0.5
4.0
V
I/O voltage for:
MPP, TWSI, JTAG, SDIO, I2S, SPI, TS, and
TDM interfaces
NOTE: The I2S, TS, and TDM interfaces are
only relevant for the 88F6192.
VHV
-0.5
3.0
V
I/O voltage for eFuse burning
PEX_AVDD
-0.5
2.2
V
Analog supply for:
PCI Express interface
USB_AVDD
-0.5
4.0
V
Analog supply for:
USB interface
88F6190 – SATA_AVDD
-0.5
4.0
V
Analog supply for:
SATA interface
88F6192 –
SATA0_AVDD
SATA1_AVDD
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 85
88F619x
Hardware Specifications
Table 41: Absolute Maximum Ratings (Continued)
Parameter
Min
Max
U n its
C om m e n ts
XTAL_AVDD
-0.5
2.2
V
Analog supply for internal clock inverter for
crystal support and current source for SATA and
USB PHYs
RTC_AVDD
-0.5
2.2
V
Analog supply for:
RTC interface
TC
-40
125
°C
Case temperature
TSTG
-40
125
°C
Storage temperature
„
„
Caution
Exposure to conditions at or beyond the maximum rating may damage the device.
Operation beyond the recommended operating conditions (Table 42) is neither
recommended nor guaranteed.
Doc. No. MV-S104987-U0 Rev. F
Page 86
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications (Preliminary)
Recommended Operating Conditions
10.2
Recommended Operating Conditions
Table 42: Recommended Operating Conditions
Parameter
M in
Ty p
Max
Units
C om m e n ts
VDD
0.95
1.0
1.05
V
Core and CPU voltage
CPU_PLL_AVDD
CORE_PLL_AVDD
1.7
1.8
1.9
V
Analog supply for the internal PLL
SSCG_AVDD
1.7
1.8
1.9
V
Analog supply for:
Internal Spread Spectrum Clock
Generator
88F6190 – VDD_GE_A
3.15
3.3
3.45
V
88F6192 –
VDD_GE_A
VDD_GE_B
I/O voltage for:
RGMII(10/100 RGMII only)/
GMII/MII/MMII/SMI interfaces
1.7
1.8
1.9
V
I/O voltage for:
RGMII/SMI interfaces
88F6190 – VDD_GE_B
3.15
3.3
3.45
V
I/O voltage for:
GMII/MII/MMII/SMI interfaces
VDD_M
1.7
1.8
1.9
V
I/O voltage for:
SDRAM interface
VDDO
3.15
3.3
3.45
V
I/O voltage for:
MPP, TWSI, JTAG, SDIO, I2S, SPI,
TS, and TDM interfaces
NOTE: The I2S, TS, and TDM
interfaces are only relevant
for the 88F6192.
VHV (during eFuse
Burning mode)
2.375
2.5
2.625
V
I/O voltage for eFuse burning
NOTE: If the VHV voltage is higher
than VDD voltage (burning
mode), VDD must be
powered before VHV, to
prevent the fuse from being
accidentally burned.
VHV (during eFuse
Reading mode)
0.95
1.0
1.05
V
I/O voltage for eFuse reading
NOTE: It is recommended that if
only a read operation is
required, VHV would be
connected to the device
VDD power.
PEX_AVDD
1.7
1.8
1.9
V
Analog supply for:
PCI Express interface
USB_AVDD
3.15
3.3
3.45
V
Analog supply for:
USB interface
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 87
88F619x
Hardware Specifications
Table 42: Recommended Operating Conditions (Continued)
Parameter
M in
Ty p
Max
Units
C om m e n ts
88F6190 – SATA_AVDD
3.15
3.3
3.45
V
Analog supply for:
SATA interface
XTAL_AVDD
1.7
1.8
1.9
V
Analog supply for:
Internal clock inverter for crystal
support and current source for
SATA and USB PHYs
RTC_AVDD
1.7
1.8
1.9
V
Analog supply for RTC in Regular
mode
1.3
1.5
1.7
V
Analog supply for RTC in Battery
Back-up mode
105
°C
Junction Temperature
88F6192 –
SATA0_AVDD
SATA1_AVDD
TJ
0
Caution
Operation beyond the recommended operating conditions is neither recommended nor
guaranteed.
Doc. No. MV-S104987-U0 Rev. F
Page 88
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications (Preliminary)
Thermal Power Dissipation
10.3
Thermal Power Dissipation
Note
Before designing a system, Marvell recommends reading application note AN-63:
Thermal Management for Marvell Technology Products. This application note presents
basic concepts of thermal management for integrated circuits (ICs) and includes
guidelines to ensure optimal operating conditions for Marvell Technology's products.
The purpose of the Thermal Power Dissipation table is to support system engineering in thermal
design.
.
Table 43: Thermal Power Dissipation
In t e r f a c e
S y m bo l
Core (including CPU)—VDD 1.0V
For the 88F6190:
PVDD
For the 88F6192:
Te s t C on d it io n s
Ty p
Units
CPU @ 600 MHz,
L2 @ 300 MHz,
Core @ 166 MHz
930
mW
CPU @ 800 MHz,
L2 @ 400 MHz,
Core @ 166 MHz
1000
mW
RGMII 1.8V interface
PRGMII
30
mW
RGMII (10/100 RGMII only) 3.3V interface
PRGMII
50
mW
GMII 3.3V interface
PGMII
50
mW
MII/MMII 3.3V interface
PMII
10
mW
Miscellaneous interfaces
(JTAG, TWSI, UART, NAND flash, Audio,
SDIO, TDM, TS, and SPI)
NOTE: The Audio, TDM, and TS
interfaces only apply to the
88F6192.
PMISC
50
mW
DDR2 SDRAM interface (On Board,
16-bit, 200 MHz)
PDDR2
180
mW
eFuse during Burning mode
NOTE: Since the eFuse burn is performed
only once, there is no thermal
effect after the burn has finished.
PFUSE
50
mW
eFuse during Reading mode
PFUSE
25
mW
PCI Express interface
PPEX
100
mW
USB interface
PUSB
120
mW
SATA interface
PSATA
88F6190 – A single SATA port
205
mW
88F6192 – Two SATA ports
410
mW
Two on board devices, 75 ohm
ODT termination
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 89
88F619x
Hardware Specifications
Notes:
1. The values are for nominal voltage.
2. Power in mW is calculated using the typical recommended VDDIO specification for each power
rail.
Doc. No. MV-S104987-U0 Rev. F
Page 90
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications (Preliminary)
Current Consumption
10.4
Current Consumption
The purpose of the Current Consumption table is to support board power design and power module
selection.
.
Table 44: Current Consumption
In t e r f a c e
S y m bo l
Core (including CPU)—VDD 1.0V
For the 88F6190:
IVDD
For the 88F6192:
Te s t C on d it io n s
Max
Units
CPU @ 600 MHz,
L2 @ 300@ MHz,
Core @ 166 MHz
1930
mA
CPU @ 800 MHz,
L2 @ 400@ MHz,
Core @ 166 MHz
2000
mA
RGMII 1.8V or 3.3V interface
IRGMII
25
mA
GMII 3.3V interface
IGMII
25
mA
MII/MMII 3.3V interface
IMII_MMII
25
mA
Miscellaneous interfaces
(JTAG, TWSI, UART, NAND flash, Audio,
SDIO, TDM, TS, and SPI)
NOTE: The Audio, TDM, TS interfaces
only apply to the 88F6192.
IMISC
25
mA
DDR2 SDRAM interface (On Board 16-bit
200 MHz)
IDDR2
450
mA
eFuse during Burning mode
IFUSE
20
mA
eFuse during Reading mode
IFUSE
25
mA
PCI Express interface
IPEX
50
mA
USB interface
IUSB
40
mA
SATA interface
ISATA
88F6190 – A single SATA port
65
mA
88F6192 – Two SATA ports
130
mA
Two on board devices, 75 ohm
ODT termination
Notes:
1. Current in mA is calculated using maximum recommended VDDIO specification for each power
rail.
2. All output clocks toggling at their specified rate.
3. Maximum drawn current from the power supply.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 91
88F619x
Hardware Specifications
10.5
DC Electrical Specifications
Note
10.5.1
See Section 2.3, Internal Pull-up and Pull-down Pins, on page 55 for internal
pullup/pulldown information.
General 3.3V (CMOS) DC Electrical Specifications
The S/PDIF / I2S and Transport Stream interfaces are only relevant for the 88F6192.
Note
The DC electrical specifications in Table 45 are applicable for the following interfaces and signals:
„
JTAG
„
RGMII (10/100 Mbps)/GMII/MII/MMII
„
Secure Digital Input/Output (SDIO)
„
S/PDIF / I2S (Audio)
„
Transport Stream (TS)
„
NAND flash
„
UART
„
MPP
„
PTP
„
SYSRSTn
In the following table, for the JTAG, SDIO, S/PDIF / I2S, TS, NAND flash, UART, PTP, and MPP
interfaces, VDDIO means the VDDO power rail. For the 88F6190 RGMII interface VDDIO means the
VDD_GE_A power rail, and for the GMII/MII/MMII interface, VDDIO means the VDD_GE_A and
VDD_GE_B power rails. For the 88F6192 RGMII/GMII/MII/MMII interface, VDDIO means the
VDD_GE_A and VDD_GE_B power rails.
Table 45: General 3.3V Interface (CMOS) DC Electrical Specifications
Param eter
Sym bol
Test Condition
Min
Typ
Max
Units Notes
Input low level
VIL
-0.3
0.8
V
-
Input high level
VIH
2.0
VDDIO+0.3
V
-
Output low level
VOL
IOL = 2 mA
-
0.4
V
-
Output high level
VOH
IOH = -2 mA
2.4
-
V
-
0 < VIN < VDDIO
-10
10
uA
1, 2
pF
-
Input leakage current
Pin capacitance
IIL
Cpin
5
Notes:
General comment: See the Pin Description section for internal pullup/pulldow n.
1. While I/O is in High-Z.
2. This current does not include the current flow ing through the pullup/pulldow n resistor.
Doc. No. MV-S104987-U0 Rev. F
Page 92
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications
DC Electrical Specifications
10.5.2
RGMII, SMI and REF_CLK_XIN 1.8V (CMOS) DC Electrical
Specifications
In the following table, for the RGMII interface, VDDIO means the VDD_GE_A power rail or
VDD_GE_B power rail (88F6192 only).
In the following table, for the REF_CLK_XIN pin, VDDIO means the XTAL_AVDD power rail.
Table 46: RGMII 1.8V Interface (CMOS) DC Electrical Specifications
Param eter
Sym bol
Test Condition
Min
Typ
Max
Units Notes
Input low level
VIL
-0.3
0.35*VDDIO
V
-
Input high level
VIH
0.65*VDDIO
VDDIO+0.3
V
-
Output low level
VOL
IOL = 2 mA
-
0.45
V
-
Output high level
VOH
IOH = -2 mA
VDDIO-0.45
-
V
-
Input leakage current
IIL
0 < VIN < VDDIO
-10
10
uA
1, 2
Pin capacitance
Cpin
pF
-
5
Notes:
General comment: See the Pin Description section for internal pullup/pulldow n.
1. While I/O is in High-Z.
2. This current does not include the current flow ing through the pullup/pulldow n resistor.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 93
88F619x
Hardware Specifications
10.5.3
SDRAM DDR2 Interface DC Electrical Specifications
In the following table, VREF is VDD_M/2 and VDDIO means the VDD_M power rail.
Table 47: SDRAM DDR2 Interface DC Electrical Specifications
Parameter
Input low level
Symbol
Test Condition
Min
Typ
Max
Units Notes
VIL
-
-0.3
VREF - 0.125
V
-
Input high level
VIH
-
VREF + 0.125
VDDIO + 0.3
V
-
Output low level
VOL
IOL = 13.4 mA
0.28
V
-
Output high level
VOH
IOH = -13.4 mA
V
-
Rtt effective impedance value
RTT
See note 2
Deviation of VM w ith respect to VDDQ/2
Input leakage current
Pin capacitance
dVm
IIL
Cpin
1.42
120
150
180
ohm
1,2
60
75
90
ohm
1,2
40
50
60
ohm
1,2
See note 3
-6
6
%
3
0 < VIN < VDDIO
-10
10
uA
4, 5
pF
-
-
5
Notes:
General comment: See the Pin Description section for internal pullup/pulldow n.
1. See SDRAM functional description section for ODT configuration.
2. Measurement definition for RTT: Apply VREF +/- 0.25 to input pin separately,
then measure current I(VREF + 0.25) and I(VREF - 0.25) respectively.
RTT =
0 .5
I (VREF + 0.25 ) − I (VREF
− 0.25 )
3. Measurement definition for VM: Measured voltage (VM) at input pin (midpoint) w ith no load.
⎛ 2 × Vm
⎞
dVM = ⎜
− 1 ⎟ × 100 %
⎝ VDDIO
⎠
4. While I/O is in High-Z.
5. This current does not include the current flow ing through the pullup/pulldow n resistor.
Doc. No. MV-S104987-U0 Rev. F
Page 94
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications
DC Electrical Specifications
10.5.4
Two-Wire Serial Interface (TWSI) 3.3V DC Electrical
Specifications
In the following table, VDDIO means the VDDO power rail.
Table 48: TWSI Interface 3.3V DC Electrical Specifications
Param eter
Sym bol
Test Condition
Min
Typ
Max
Units Notes
Input low level
VIL
-0.5
0.3*VDDIO
V
-
Input high level
VIH
0.7*VDDIO
VDDIO+0.5
V
-
Output low level
VOL
IOL = 3 mA
-
0.4
V
-
Input leakage current
IIL
0 < VIN < VDDIO
-10
10
uA
1, 2
Pin capacitance
Cpin
pF
-
5
Notes:
General comment: See the Pin Description section for internal pullup/pulldow n.
1. While I/O is in High-Z.
2. This current does not include the current flow ing through the pullup/pulldow n resistor.
10.5.5
Serial Peripheral Interface (SPI) 3.3V DC Electrical
Specifications
In the following table VDDIO means the VDDO power rail.
Table 49: SPI Interface 3.3V DC Electrical Specifications
Param eter
Sym bol
Test Condition
Min
Typ
Max
Units Notes
Input low level
VIL
-0.5
0.3*VDDIO
V
-
Input high level
VIH
0.7*VDDIO
VDDIO+0.5
V
-
Output low level
VOL
IOL = 4 mA
-
0.4
V
-
Output high level
VOH
IOH = -4 mA
VDDIO-0.6
-
V
-
Input leakage current
IIL
0 < VIN < VDDIO
10
uA
1, 2
Pin capacitance
Cpin
pF
-
-10
5
Notes:
General comment: See the Pin Description section for internal pullup/pulldow n.
1. While I/O is in High-Z.
2. This current does not include the current flow ing through the pullup/pulldow n resistor.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 95
88F619x
Hardware Specifications
10.5.6
Time Division Multiplexing (TDM) 3.3V DC Electrical
Specifications
The TDM interface is only relevant for the 88F6192.
Note
In the following table VDDIO means the either the VDDO or the VDD_GE_B power rail, depending
on which MPP pins are configured for the TDM interface.
Table 50: TDM Interface 3.3V DC Electrical Specifications
Param eter
Sym bol
Test Condition
Min
Typ
Max
Units Notes
Input low level
VIL
-0.5
0.3*VDDIO
V
-
Input high level
VIH
0.7*VDDIO
VDDIO+0.5
V
-
Output low level
VOL
IOL = 4 mA
-
0.4
V
-
Output high level
VOH
IOH = -4 mA
VDDIO-0.6
-
V
-
Input leakage current
IIL
0 < VIN < VDDIO
-10
10
uA
1, 2
Pin capacitance
Cpin
pF
-
5
Notes:
General comment: See the Pin Description section for internal pullup/pulldow n.
1. While I/O is in High-Z.
2. This current does not include the current flow ing through the pullup/pulldow n resistor.
Doc. No. MV-S104987-U0 Rev. F
Page 96
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications
AC Electrical Specifications
10.6
AC Electrical Specifications
See Section 10.7, Differential Interface Electrical Characteristics, on page 127 for differential
interface specifications.
10.6.1
Reference Clock AC Timing Specifications
Table 51: Reference Clock AC Timing Specifications
D e s c r i p t io n
Sy m b o l
Min
Max
Units
Frequency
FREF_CLK_XIN
25 50 ppm
25 +
50 ppm
MHz
Clock duty cycle
DCREF_CLK_XIN
40
60
%
Slew rate
SRREF_CLK_XIN
0.7
Pk-Pk jitter
JRREF_CLK_XIN
Notes
CPU and Core Reference Clock
V/ns
1
200
ps
2.5 100 ppm
50 +
100 ppm
MHz
7
35
65
%
7
V/ns
1, 7
256 X Fs
kHz
3
256 X Fs
kHz
3
64 X Fs
kHz
3
MHz
2
kHz
4
E t h er n e t R e f e r e n c e C lo c k
Frequency in MII/MMII-MAC mode
FGE_TXCLK_OUT
FGE_RXCLK
MII/MMII-MAC mode clock duty cycle
DCGE_TXCLK_OUT
DCGE_RXCLK
Slew rate
SRGE_TXCLK_OUT
SRGE_RXCLK
0.7
A u d io E x t e r n a l R e f e r e n c e C lo c k ( O n ly r e l e va n t f o r t h e 8 8 F 6 1 9 2 )
Audio external reference clock
FAU_EXTCLK
S / P D I F R e c o v e r e d M a s t e r C loc k ( O n ly r e l e v an t f o r t h e 8 8 F 6 1 9 2 )
S/PDIF recovered master clock
FAU_SPDFRMCLK
2
I S R e f e r e n c e C lo c k ( O n l y r e l e v a n t f o r t h e 88 F 6 1 9 2 )
I2S clock
FI2S_BCLK
SP I O ut pu t C l o c k
SPI output clock
FSPI_SCK
TCLK/30
TCLK/4
RTC Reference Clock
RTC_XIN crystal frequency
FRTC_XIN
32.768
Tra n s p o r t St r e a m ( T S ) O u t pu t M o d e R e f e r e n ce C l o c k ( O n l y r e le v a n t f o r t h e 8 8 F 6 19 2 )
TS output clock in parallel mode
FTS0_CLK, FTS1_CLK
9.61
12.5
MHz
5
TS output clock in serial mode
FTS0_CLK, FTS1_CLK
9.61
83
MHz
5
Tr a n s p o r t St r e a m In p u t M o d e R e f e r en c e C lo c k ( O n ly r e le v a n t f o r t h e 8 8 F 6 1 9 2 )
TS input clock in parallel mode
FTS0_CLK, FTS1_CLK
13.5
MHz
TS input clock in serial mode
FTS0_CLK, FTS1_CLK
83
MHz
Tr a n s p o r t St r e a m E x t e r n a l R e f e r e nc e C lo c k ( O n ly r e l e v an t f o r t h e 8 8 F 6 1 9 2 )
TS external clock in parallel mode
FEXT_CLK
9.61
12.5
MHz
5
TS external clock in serial mode
FEXT_CLK
9.61
83
MHz
5
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 97
88F619x
Hardware Specifications
Table 51: Reference Clock AC Timing Specifications (Continued)
D e s c r i p t io n
Sy m b o l
Min
Max
Units
Notes
T D M _ S P I O u t p u t C lo c k ( O n ly r e l ev a n t f o r t h e 8 8 F 6 1 9 2 )
TDM_SPI output clock
8.192
FTDM_SPI_SCK
MHz
S M I M a s t e r M o d e R e f e r e n c e C l o ck
SMI output MDC clock
FGE_MDC
TCLK/128
MHz
T WS I M a s t er M o d e R e fe re n c e C lo c k
SCK output clock
FTW_SCK
TCLK/
1600
kHz
6
PT P R e fe r e n c e C lo c k
Frequency
FPTP_CLK
125 100 ppm
125 +
100 ppm
MHz
60
%
Clock duty cycle
DCPTP_CLK
40
Slew rate
SRPTP_CLK
0.7
Pk-Pk jitter
JRPTP_CLK
V/ns
100
1
ps
Notes:
1. Slew rate is defined from 20% to 80% of the reference clock signal.
2. For additional information regarding configuring this clock, see the Serial Memory Interface
Control Register in the 88F6180, 88F6190, 88F6192, and 88F6281 Functional Specifications.
3. Fs is the audio sample rate, which can be configured to 44.1 kHz, 48 kHz, or 96 kHz (see the
Audio (I2S / S/PDIF) Interface section in the 88F6180, 88F6190, 88F6192, and 88F6281
Functional Specifications).
4.
The RTC design was optimized for a standard CL = 12.5 pF crystal. No passive components
are provided internally. Connect the crystal and the passive network as recommended by the
crystal manufacturer.
5.
The frequency can be set using the TS Interface Configuration register (see the 88F6180,
88F6190, 88F6192, and 88F6281 Functional Specifications).
For the minimum value refer to the Baud Rate Register section of the 88F6180, 88F6190,
88F6192, and 88F6281 Functional Specifications.
The Ethernet Reference Clock parameters refer both to the reference clock for an Ethernet port
configured using the dedicated port pins and for an Ethernet port configured using the
multiplexed port pins.
6.
7.
Doc. No. MV-S104987-U0 Rev. F
Page 98
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications
AC Electrical Specifications
10.6.2
SDRAM DDR2 Interface AC Timing
10.6.2.1
SDRAM DDR2 Interface AC Timing Table
Table 52: SDRAM DDR2 Interface AC Timing Table
200 MHz @ 1.8V
Description
Sym bol
Clock frequency
Min
fCK
Max
200.00
Units
Notes
MHz
-
ns
-
DQ and DM valid output time before DQS transition
tDOVB
0.50
-
DQ and DM valid output time after DQS transition
tDOVA
0.50
-
ns
-
DQ and DM output pulse w idth
tDIPW
0.37
-
tCK
-
DQS output high pulse w idth
tDQSH
0.37
-
tCK
-
DQS output low pulse w idth
tDQSL
0.37
-
tCK
-
DQS falling edge to CLK-CLKn rising edge
tDSS
0.34
-
tCK
1
DQS falling edge from CLK-CLKn rising edge
tDSH
0.34
-
tCK
1
CLK-CLKn rising edge to DQS output rising edge
tDQSS
-0.11
0.11
tCK
-
DQS w rite preamble
tWPRE
0.35
-
tCK
-
DQS w rite postamble
tWPST
0.42
-
tCK
-
CLK-CLKn high-level w idth
tCH
0.45
0.55
tCK
1
CLK-CLKn low -level w idth
tCL
0.45
0.55
tCK
1
DQ input setup time relative to DQS in transition
tDSI
-0.55
-
ns
-
DQ input hold time relative to DQS in transition
tDHI
1.50
-
ns
-
Address and Control valid output time before CLK-CLkn rising edge
tAOVB
1.70
-
ns
1, 2
Address and Control valid output time after CLK-CLKn rising edge
tAOVA
1.70
-
ns
1, 2
tIPW
0.67
-
tCK
-
Address and control output pulse w idth
Notes:
General comment: All timing values w ere measured from vref to vref, unless otherw ise specified.
General comment: All input timing values assume minimum slew rate of 1 V/ns (slew rate measured from Vref +/-125 mV).
General comment: tCK = 1/fCK.
General comment: For all signals, the load is CL = 8 pF.
1. This timing value is defined on CLK / CLKn crossing point.
2. This timing value is defined w hen Address and Control signals are output w ith CLK-CLKn falling edge.
For more information, see register settings.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 99
88F619x
Hardware Specifications
10.6.2.2
SDRAM DDR2 Interface Test Circuit
Figure 8: SDRAM DDR2 Interface Test Circuit
VTT
Test Point
50 ohm
CL
10.6.2.3
SDRAM DDR2 Interface AC Timing Diagrams
Figure 9: SDRAM DDR2 Interface Write AC Timing Diagram
CLK
tCH
tDSH
tDSS
tDQSH
tDQSL
tCL
CLKn
DQS
tWPRE
tWPST
DQSn
tDIPW
DQ
tDOVB tDOVA
Doc. No. MV-S104987-U0 Rev. F
Page 100
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications
AC Electrical Specifications
Figure 10: SDRAM DDR2 Interface Address and Control AC Timing Diagram
CLK
tCH
tCL
CLKn
tIPW
ADDRESS/
CONTROL
tAOVB
tAOVA
Figure 11: SDRAM DDR2 Interface Read AC Timing Diagram
DQS
DQSn
DQ
tDSI
tDHI
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 101
88F619x
Hardware Specifications
10.6.3
Reduced Gigabit Media Independent Interface (RGMII)
AC Timing
10.6.3.1
RGMII AC Timing Table
Table 53: RGMII 10/100/1000 AC Timing Table at 1.8V
Description
Sym bol
Clock frequency
fCK
Data to Clock output skew
Data to Clock input skew
Min
Max
125.0
Units Notes
MHz
-
Tskew T
-0.50
0.50
ns
2
Tskew R
1.00
2.60
ns
-
Clock cycle duration
Tcyc
7.20
8.80
ns
1,2
Duty cycle for Gigabit
Duty_G
0.45
0.55
tCK
2
Duty cycle for 10/100 Megabit
Duty_T
0.40
0.60
tCK
2
Notes:
General comment: All values w ere measured from vddio/2 to vddio/2, unless otherw ise specified.
General comment: tCK = 1/fCK.
General comment: If the PHY does not support internal-delay mode, the PC board design requires
routing clocks so that an additional trace delay of greater than 1.5 ns and less
than 2.0 ns is added to the associated clock signal.
For 10/100 Mbps RGMII, the Max value is unspecified.
1. For RGMII at 10 Mbps and 100 Mbps, Tcyc w ill scale to 400 ns +/-40 ns and 40 ns +/-4 ns, respectively.
2. For all signals, the load is CL = 5 pF.
Table 54: RGMII 10/100 AC Timing Table at 3.3V
Description
Sym bol
Clock frequency
Min
fCK
Data to Clock output skew
Data to Clock input skew
Tskew T
Max
25.0
-0.50
0.50
Units Notes
MHz
-
ns
2
Tskew R
1.00
2.60
ns
-
Tcyc
7.20
8.80
ns
1,2
Duty cycle for Gigabit
Duty_G
0.45
0.55
tCK
2
Duty cycle for 10/100 Megabit
Duty_T
0.40
0.60
tCK
2
Clock cycle duration
Notes:
General comment: All values w ere measured from vddio/2 to vddio/2, unless otherw ise specified.
General comment: tCK = 1/fCK.
General comment: If the PHY does not support internal-delay mode, the PC board design requires
routing clocks so that an additional trace delay of greater than 1.5 ns
is added to the associated clock signal.
For 10/100 Mbps RGMII, the Max value is unspecified.
1. For RGMII at 10 Mbps and 100 Mbps, Tcyc w ill scale to 400 ns +/-40 ns and 40 ns +/-4 ns, respectively.
2. For all signals, the load is CL = 5 pF.
Doc. No. MV-S104987-U0 Rev. F
Page 102
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications
AC Electrical Specifications
10.6.3.2
RGMII Test Circuit
Figure 12: RGMII Test Circuit
Test Point
CL
10.6.3.3
RGMII AC Timing Diagram
Figure 13: RGMII AC Timing Diagram
TX
CLOCK
(At Transmitter)
TX
DATA
TskewT
RX
CLOCK
(At Receiver)
RX
DATA
TskewR
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 103
88F619x
Hardware Specifications
10.6.4
Gigabit Media Independent Interface (GMII) AC Timing
10.6.4.1
GMII AC Timing Table
Table 55: GMII AC Timing Table
125 MHz
Description
GTX_CLK cycle time
Sym bol
Min
Max
Units
Notes
tCK
7.5
8.5
ns
-
RX_CLK cycle time
tCKrx
7.5
-
ns
-
GTX_CLK and RX_CLK high level w idth
tHIGH
2.5
-
ns
1
GTX_CLK and RX_CLK low level w idth
tLOW
2.5
-
ns
1
tR
-
1.0
ns
1, 2
GTX_CLK and RX_CLK rise time
GTX_CLK and RX_CLK fall time
tF
-
1.0
ns
1, 2
Data input setup time relative to RX_CLK rising edge
tSETUP
2.0
-
ns
-
Data input hold time relative to RX_CLK rising edge
tHOLD
0.0
-
ns
-
Data output valid before GTX_CLK rising edge
tOVB
2.5
-
ns
1
Data output valid after GTX_CLK rising edge
tOVA
0.5
-
ns
1
Notes:
General comment: All values w ere measured from VIL(max) to VIH(min), unless otherw ise specified.
1. For all signals, the load is CL = 5 pF.
2. Rise time measured from VIL(max) to VIH(min), fall time measured from VIH(min) to VIL(max).
10.6.4.2
GMII Test Circuit
Figure 14: GMII Test Circuit
Test Point
CL
Doc. No. MV-S104987-U0 Rev. F
Page 104
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications
AC Electrical Specifications
10.6.4.3
GMII AC Timing Diagrams
Figure 15: GMII Output AC Timing Diagram
tLOW
tHIGH
VIH(min)
GTX_CLK
VIL(max)
VIH(min)
TXD, TX_EN, TX_ER
VIL(max)
tOVB
tOVA
Figure 16: GMII Input AC Timing Diagram
tLOW
tHIGH
VIH(min)
RX_CLK
VIL(max)
VIH(min)
RXD, RX_EN, RX_ER
VIL(max)
tSETUP
tHOLD
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 105
88F619x
Hardware Specifications
10.6.5
Media Independent Interface/Marvell Media Independent
Interface (MII/MMII) AC Timing
10.6.5.1
MII/MMII MAC Mode AC Timing Table
Table 56: MII/MMII MAC Mode AC Timing Table
Sym bol
Min
Max
Units
Notes
Data input setup relative to RX_CLK rising edge
Description
tSU
3.5
-
ns
-
Data input hold relative to RX_CLK rising edge
tHD
2.0
-
ns
-
Data output delay relative to MII_TX_CLK rising edge
tOV
0.0
10.0
ns
1
Notes:
General comment: All values w ere measured from VIL(max) to VIH(min), unless otherw ise specified.
1. For all signals, the load is CL = 5 pF.
10.6.5.2
MII/MMII MAC Mode Test Circuit
Figure 17: MII/MMII MAC Mode Test Circuit
Test Point
CL
10.6.5.3
MII/MMII MAC Mode AC Timing Diagrams
Figure 18: MII/MMII MAC Mode Output Delay AC Timing Diagram
Vih(min)
MII_TX_CLK
Vil(max)
Vih(min)
TXD, TX_EN, TX_ER
Vil(max)
TOV
Doc. No. MV-S104987-U0 Rev. F
Page 106
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications
AC Electrical Specifications
Figure 19: MII/MMII MAC Mode Input AC Timing Diagram
Vih(min)
RX_CLK
Vih(min)
RXD, RX_EN, RX_ER
Vil(max)
tSU
tHD
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 107
88F619x
Hardware Specifications
10.6.6
Serial Management Interface (SMI) AC Timing
10.6.6.1
SMI Master Mode AC Timing Table
Table 57: SMI Master Mode AC Timing Table
Description
Sym bol
Min
Max
See note 2
Units
Notes
MHz
2
MDC clock frequency
fCK
MDC clock duty cycle
tDC
0.4
0.6
tCK
-
MDIO input setup time relative to MDC rise time
tSU
40.0
-
ns
-
MDIO input hold time relative to MDC rise time
tHO
0.0
-
ns
-
MDIO output valid before MDC rise time
tOVB
15.0
-
ns
1
MDIO output valid after MDC rise time
tOVA
15.0
-
ns
1
Notes:
General comment: All timing values w ere measured from VIL(max) and VIH(min) levels, unless otherw ise specified.
General comment: tCK = 1/fCK.
1. For MDC signal, the load is CL = 390 pF, and for MDIO signal, the load is CL = 470 pF.
2. See "Reference Clocks" table for more details.
10.6.6.2
SMI Master Mode Test Circuit
Figure 20: MDIO Master Mode Test Circuit
VDDIO
Test Point
2 kilohm
MDIO
CL
Doc. No. MV-S104987-U0 Rev. F
Page 108
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications
AC Electrical Specifications
Figure 21: MDC Master Mode Test Circuit
Test Point
MDC
CL
10.6.6.3
SMI Master Mode AC Timing Diagrams
Figure 22: SMI Master Mode Output AC Timing Diagram
VIH(min)
MDC
VIH(min)
MDIO
VIL(max)
tOVB tOVA
Figure 23: SMI Master Mode Input AC Timing Diagram
VIH(min)
MDC
VIH(min)
MDIO
VIL(max)
tSU
tHO
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 109
88F619x
Hardware Specifications
10.6.7
JTAG Interface AC Timing
10.6.7.1
JTAG Interface AC Timing Table
Table 58: JTAG Interface AC Timing Table
30 MHz
Description
Sym bol
Min
Max
30.0
Units
Notes
JTClk frequency
fCK
MHz
-
JTClk minimum pulse w idth
Tpw
0.45
0.55
tCK
-
JTClk rise/fall slew rate
Sr/Sf
0.50
-
V/ns
2
JTRSTn active time
Trst
1.0
-
ms
-
TMS, TDI input setup relative to JTClk rising edge
Tsetup
6.67
-
ns
-
TMS, TDI input hold relative to JTClk rising edge
Thold
13.0
-
ns
-
JTClk falling edge to TDO output delay
Tprop
1.0
8.33
ns
1
Notes:
General comment: All values w ere measured from vddio/2 to vddio/2, unless otherw ise specified.
General comment: tCK = 1/fCK.
1. For TDO signal, the load is CL = 10 pF.
2. Defined from VIL to VIH for rise time, and from VIH to VIL for fall time.
10.6.7.2
JTAG Interface Test Circuit
Figure 24: JTAG Interface Test Circuit
Test Point
CL
Doc. No. MV-S104987-U0 Rev. F
Page 110
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications
AC Electrical Specifications
10.6.7.3
JTAG Interface AC Timing Diagrams
Figure 25: JTAG Interface Output Delay AC Timing Diagram
Tprop
(max)
JTCK
VIH
VIL
TDO
Tprop
(min)
Figure 26: JTAG Interface Input AC Timing Diagram
JTCK
TMS,TDI
Tsetup
Thold
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 111
88F619x
Hardware Specifications
10.6.8
Two-Wire Serial Interface (TWSI) AC Timing
10.6.8.1
TWSI AC Timing Table
Table 59: TWSI Master AC Timing Table
Description
Sym bol
SCK clock frequency
fCK
Min
Max
See note 1
Units
Notes
kHz
1
SCK minimum low level w idth
tLOW
0.47
-
tCK
2
SCK minimum high level w idth
tHIGH
0.40
-
tCK
2
SDA input setup time relative to SCK rising edge
tSU
250.0
-
ns
-
SDA input hold time relative to SCK falling edge
tHD
0.0
-
ns
-
SDA and SCK rise time
tr
-
1000.0
ns
2, 3
SDA and SCK fall time
tf
-
300.0
ns
2, 3
tOV
0.0
0.4
tCK
2
SDA output delay relative to SCK falling edge
Notes:
General comment: All values referred to VIH(min) and VIL(max) levels, unless otherw ise specified.
General comment: tCK = 1/fCK.
1. See "Reference Clocks" table for more details.
2. For all signals, the load is CL = 100 pF, and RL value can be 500 ohm to 8 kilohm.
3. Rise time measured from VIL(max) to VIH(min), fall time measured from VIH(min) to VIL(max).
Table 60: TWSI Slave AC Timing Table
100 kHz
Sym bol
Min
Max
Units
Notes
SCK minimum low level w idth
tLOW
4.7
-
us
1
SCK minimum high level w idth
Description
tHIGH
4.0
-
us
1
SDA input setup time relative to SCK rising edge
tSU
250.0
-
ns
-
SDA input hold time relative to SCK falling edge
tHD
0.0
-
ns
-
tr
-
1000.0
ns
1, 2
tf
-
300.0
ns
1, 2
tOV
0.0
4.0
us
1
SDA and SCK rise time
SDA and SCK fall time
SDA output delay relative to SCK falling edge
Notes:
General comment: All values referred to VIH(min) and VIL(max) levels, unless otherw ise specified.
1. For all signals, the load is CL = 100 pF, and RL value can be 500 ohm to 8 kilohm.
2. Rise time measured from VIL(max) to VIH(min), fall time measured from VIH(min) to VIL(max).
Doc. No. MV-S104987-U0 Rev. F
Page 112
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications
AC Electrical Specifications
10.6.8.2
TWSI Test Circuit
Figure 27: TWSI Test Circuit
VDDIO
Test Point
RL
CL
10.6.8.3
TWSI AC Timing Diagrams
Figure 28: TWSI Output Delay AC Timing Diagram
tHIGH
tLOW
Vih(min)
SCK
Vil(max)
Vih(min)
SDA
Vil(max)
tOV(min)
tOV(max)
Figure 29: TWSI Input AC Timing Diagram
tLOW
tHIGH
Vih(min)
SCK
Vil(max)
Vih(min)
SDA
Vil(max)
tSU
tHD
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 113
88F619x
Hardware Specifications
10.6.9
Sony/Philips Digital Interconnect Format (S/PDIF) AC
Timing
The S/PDIF interface is only relevant for the 88F6192.
Note
10.6.9.1
S/PDIF AC Timing Table
Table 61: S/PDIF AC Timing Table
Description
Sym bol
Min
Max
Units
Notes
Output frequency accuracy
Ftxtol
-50.0
50.0
ppm
1
Input frequency accuracy
Frxtol
-100.0
100.0
ppm
-
Txjit
-
0.05
UI
1, 2
Txjitgain
-
3.0
dB
3
-
10.0
UI
4
-
0.25
UI
5
-
0.2
UI
6
Output jitter - total peak-to-peak
Jitter transfer gain
Input jitter - total peak-to-peak
Rxjit
Notes:
General comment: All values w ere measured from VIL(max) to VIH(min), unless otherw ise specified.
General comment: For more information, refer to the Digital Audio Interface - Part 3: Consumer Applications,
IEC 60958-3:2003(E), Chapter 7.3, January 2003.
1. For all signals, the load is CL = 10 pF.
2. Using inristic jitter filter.
3. Refer to Figure-8 in IEC 60958-3:2003(E), Chapter 7.3, January 2003.
4. Defined for up to 5 Hz.
5. Defined from 200 Hz to 400 kHz.
6. Defined for above 400 kHz.
Note
For additional information about working with a coax connection, see the 88F6180,
88F6190, 88F6192, and 88F6281 Design Guide.
Doc. No. MV-S104987-U0 Rev. F
Page 114
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications
AC Electrical Specifications
10.6.9.2
S/PDIF Test Circuit
Figure 30: S/PDIF Test Circuit
Test Point
CL
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 115
88F619x
Hardware Specifications
10.6.10
Inter-IC Sound Interface (I2S) AC Timing
The I2S interface is only relevant for the 88F6192.
Note
10.6.10.1
Inter-IC Sound (I2S) AC Timing Table
Table 62: Inter-IC Sound (I2S) AC Timing Table
Description
Sym bol
I2SBCLK clock frequency
I2SBCLK clock high/low level pulse w idth
Min
Max
See note 2
fCK
Units
Notes
MHz
2
tCH/tCL
0.37
-
tCK
1
I2SDI input setup time relative to I2SBCLK rise time
tSU
0.10
-
tCK
-
I2SDI input hold time relative to I2SBCLK rise time
tHO
0.00
-
ns
-
I2SDO, I2SLRCLK output delay relative to I2SBCLK rise time
tOD
0.10
0.70
tCK
1
Notes:
General comment: All timing values w ere measured from VIL(max) and VIH(min) levels, unless otherw ise specified.
General comment: tCK = 1/fCK.
1. For all signals, the load is CL = 15 pF.
2. See "Reference Clocks" table for more details.
10.6.10.2
Inter-IC Sound (I2S) Test Circuit
Figure 31: Inter-IC Sound (I2S) Test Circuit
Test Point
CL
Doc. No. MV-S104987-U0 Rev. F
Page 116
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications
AC Electrical Specifications
10.6.10.3
Inter-IC Sound (I2S) AC Timing Diagrams
Figure 32: Inter-IC Sound (I2S) Output Delay AC Timing Diagram
tCL
tCH
VIH(min)
I2SBCLK
VIL(max)
VIH(min)
I2SDO,
I2SLRCLK
VIL(max)
tODmin
tODmax
Figure 33: Inter-IC Sound (I2S) Input AC Timing Diagram
tCL
tCH
VIH(min)
I2SBCLK
VIL(max)
VIH(min)
I2SDI
VIL(max)
tSU
tHO
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 117
88F619x
Hardware Specifications
10.6.11
Time Division Multiplexing (TDM) Interface AC Timing
The TDM interface is only relevant for the 88F6192.
Note
10.6.11.1
TDM Interface AC Timing Table
Table 63: TDM Interface AC Timing Table
8.192 MHz
Description
Sym bol
Min
Max
Units
Notes
PCLK cycle time
1/tC
0.256
8.192
MHz
1, 3
PCLK duty cycle
tDTY
0.4
0.6
tC
1
PCLK rise/fall time
tR/tF
-
3.0
ns
1, 2, 8
tD
0.0
20.0
ns
1, 4, 6
DRX and FSYNC setup time relative to PCLK falling edge
tSU
10.0
-
ns
5, 7
DRX and FSYNC hold time relative to PCLK falling edge
tHD
10.0
-
ns
5, 7
DTX and FSYNC valid after PCLK rising edge
Notes:
General comment: All values w ere measured from vddio/2 to vddio/2, unless otherw ise specified.
1. For all signals, the load is CL = 20 pF.
2. Rise and Fall times are referenced to the 20% and 80% levels of the w aveform.
3. PCLK can be configured to 0.256, 0.512, 0.768, 1.024, 1.536, 2.048, 4.096, 8.192 MHz frequencies only.
4. This parameter is relevant to FSYNC signal in master-mode only.
5. This parameter is relevant to FSYNC signal in slave-mode only.
6. In negative-mode, the DTX signal is relative to PCLK falling edge.
7. In negative-mode, the DRX signal is relative to PCLK rising edge.
8. This parameter is relevant w hen the PCLK pin is output.
Doc. No. MV-S104987-U0 Rev. F
Page 118
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications
AC Electrical Specifications
10.6.11.2
TDM Interface Test Circuit
Figure 34: TDM Interface Test Circuit
Test Point
CL
10.6.11.3
TDM Interface Timing Diagrams
Figure 35: TDM Interface Output Delay AC Timing Diagram
tC
PCLK
DTX
tD
tD
Figure 36: TDM Interface Input Delay AC Timing Diagram
tC
PCLK
DRX
tSU
tHD
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 119
88F619x
Hardware Specifications
10.6.12
Serial Peripheral Interface (SPI) AC Timing
10.6.12.1
SPI (Master Mode) AC Timing Table
Table 64: SPI (Master Mode) AC Timing Table
SPI
Description
Sym bol
Min
Max
See Note 3
Units
Notes
MHz
3
tCK
1
SCLK clock frequency
fCK
SCLK high time
tCH
0.46
SCLK low time
tCL
0.46
-
tCK
1
SCLK slew rate
tSR
0.5
-
V/ns
1
Data out valid relative to SCLK falling edge
tDOV
-2.5
2.5
ns
1
CS active before SCLK rising edge
tCSB
8.0
-
ns
1
CS not active after SCLK rising edge
-
tCSA
8.0
-
ns
1
Data in setup time relative to SCLK rising edge
tSU
0.2
-
tCK
2
Data in hold time relative to SCLK rising edge
tHD
5.0
-
ns
2
Notes:
General comment: All values w ere measured from 0.3*vddio to 0.7*vddio, unless otherw ise specified.
General comment: tCK = 1/fCK.
1. For all signals, the load is CL = 10 pF.
2. Defined from vddio/2 to vddio/2.
3. See "Reference Clocks" table for more details.
10.6.12.2
SPI (Master Mode) Test Circuit
Figure 37: SPI (Master Mode) Test Circuit
Test Point
CL
Doc. No. MV-S104987-U0 Rev. F
Page 120
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications
AC Electrical Specifications
10.6.12.3
SPI (Master Mode) Timing Diagrams
Figure 38: SPI (Master Mode) Output AC Timing Diagram
tCH
tCL
SCLK
Data
Out
tDOVmin
tDOVmax
CS
tCSB
tCSA
Figure 39: SPI (Master Mode) Input AC Timing Diagram
SCLK
Data in
tSU
tHD
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 121
88F619x
Hardware Specifications
10.6.13
Secure Digital Input/Output (SDIO) Interface AC Timing
10.6.13.1
Secure Digital Input/Output (SDIO) AC Timing Table
Table 65: SDIO Host in High Speed Mode AC Timing Table
Description
Symbol
Min
Max
Units
Notes
fCK
0
50
MHz
-
Clock high/low level pulse w idth
tWL/tWH
0.35
-
tCK
1, 3
Clock rise/fall time
tTLH/tTHL
-
3.0
ns
1, 3
CMD, DAT output valid before CLK rising edge
tDOVB
6.5
-
ns
2, 3
CMD, DAT output valid after CLK rising edge
tDOVA
2.5
-
ns
2, 3
CMD, DAT input setup relative to CLK rising edge
tISU
7.0
-
ns
2
CMD, DAT input hold relative to CLK rising edge
tIHD
0.0
-
ns
2
Clock frequency in Data Transfer Mode
Notes:
General comment: tCK = 1/fCK.
1. Defined on VIL(max) and VIH(min) levels.
2. Defined on VDDIO/2 for Clock signal, and VIL(max) / VIH(min) for CMD & DAT signals.
3. For all signals, the load is CL = 10 pF.
10.6.13.2
Secure Digital Input/Output (SDIO) Test Circuit
Figure 40: Secure Digital Input/Output (SDIO) Test Circuit
VDDIO
Test Point
50 KOhm
CL
Doc. No. MV-S104987-U0 Rev. F
Page 122
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications
AC Electrical Specifications
10.6.13.3
Secure Digital Input/Output (SDIO) AC Timing Diagrams
Figure 41: SDIO Host in High Speed Mode Output AC Timing Diagram
tWL
tWH
VIH(min)
VDDIO/2
CLK
VIL(max)
VIH(min)
DAT,
CMD
VIL(max)
tDOVB tDOVA
Figure 42: SDIO Host in High Speed Mode Input AC Timing Diagram
tWL
tWH
VIH(min)
VDDIO/2
CLK
VIL(max)
VIH(min)
DAT,
CMD
VIL(max)
tISU
tIHD
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 123
88F619x
Hardware Specifications
10.6.14
Transport Stream (TS) Interface AC Timing
The TS interface is only relevant for the 88F6192.
Note
10.6.14.1
Transport Stream Interface AC Timing Table
Table 66: Transport Stream Output Interface AC Timing Table
Description
Sym bol
Clock frequency
Min
Max
See note 1
fCK
Units
Notes
MHz
1
Clock minimum low level w idth
tLOW
0.4
0.6
tCK
2
Clock minimum high level w idth
tHIGH
0.4
0.6
tCK
2
tOV
0.4
0.6
tCK
2, 3
Data output valid after Clock rising edge
Notes:
General comment: All values w ere measured from VIL(max) to VIH(min), unless otherw ise specified.
General comment: tCK = 1/fCK.
1. See "Reference Clocks" table for more details.
2. For all signals, the load is CL = 5 pF.
3. When configured to falling edge, the tOV parameter is relative to Clock falling edge.
Table 67: Transport Stream Input Interface AC Timing Table
Description
Sym bol
Clock frequency
fCK
Min
Max
See note 1
Units
Notes
MHz
1
Clock minimum low level w idth
tLOW
0.35
0.65
tCK
-
Clock minimum high level w idth
tHIGH
0.35
0.65
tCK
-
Data input setup time relative to Clock rising edge
tSU
0.30
-
tCK
2
Data input setup time relative to Clock rising edge
tHD
0.30
-
tCK
2
Notes:
General comment: All values w ere measured from VIL(max) to VIH(min), unless otherw ise specified.
General comment: tCK = 1/fCK.
1. See "Reference Clocks" table for more details.
2. When configured to falling edge, the tSU/tHD parameters are relative to Clock falling edge.
Doc. No. MV-S104987-U0 Rev. F
Page 124
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications
AC Electrical Specifications
10.6.14.2
Transport Stream Interface Test Circuit
Figure 43: Transport Stream Interface Test Circuit
Test Point
CL
10.6.14.3
Transport Stream Interface Timing Diagrams
Figure 44: Transport Stream Output Interface AC Timing Diagram
tHIGH
tLOW
Vih(min)
Clock
Vil(max)
Vih(min)
Data Out
Vil(max)
tOV(min)
tOV(max)
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 125
88F619x
Hardware Specifications
Figure 45: Transport Stream Input Interface AC Timing Diagram
tLOW
tHIGH
Vih(min)
Clock
Vil(max)
Vih(min)
Data In
Vil(max)
tSU
tHD
Doc. No. MV-S104987-U0 Rev. F
Page 126
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications
Differential Interface Electrical Characteristics
10.7
Differential Interface Electrical Characteristics
This section provides the reference clock, AC, and DC characteristics for the following differential
interfaces:
„
PCI Express Interface Electrical Characteristics
„
SATA Interface Electrical Characteristics
„
USB Electrical Characteristics
10.7.1
Differential Interface Reference Clock Characteristics
10.7.1.1
PCI Express Interface Differential Reference Clock Characteristics
Table 68: PCI Express Interface Differential Reference Clock Characteristics
Description
Sym bol
Clock frequency
fCK
Clock duty cycle
DCrefclk
Min
Max
100.0
Units
Notes
MHz
-
0.4
0.6
tCK
-
Differential rising/falling slew rate
SRrefclk
0.6
4.0
V/nS
3
Differential high voltage
VIHrefclk
150.0
-
mV
-
Differential low voltage
VILrefclk
-
-150.0
mV
-
Vcross
250.0
550.0
mV
1
Absolute crossing point voltage
Variation of Vcross over all rising clock edges
Vcrs_dlta
-
140.0
mV
1
Average differential clock period accuracy
Tperavg
-300.0
2800.0
ppm
-
Absolute differential clock period
Tperabs
9.8
10.2
nS
2
Tccjit
-
150.0
pS
-
Differential clock cycle-to-cycle jitter
Notes:
General Comment: The reference clock timings are based on 100 ohm test circuit.
General Comment: Refer to the PCI Express Card Electromechanical Specification, Revision 1.1,
March 2005, section 2.1.3 for more information.
1. Defined on a single-ended signal.
2. Including jitter and spread spectrum.
3. Defined from -150 mV to +150 mV on the differential w aveform.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 127
88F619x
Hardware Specifications
PCI Express Interface Spread Spectrum Requirements
Table 69: PCI Express Interface Spread Spectrum Requirements
Min
Max
Units
Notes
Fmod
Sym bol
0.0
33.0
kHz
1
Fspread
-0.5
0.0
%
1
Notes:
1. Defined on linear sw eep or “Hershey’s Kiss” (US Patent 5,631,920) modulations.
Doc. No. MV-S104987-U0 Rev. F
Page 128
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications
Differential Interface Electrical Characteristics
10.7.2
PCI Express Interface Electrical Characteristics
10.7.2.1
PCI Express Interface Driver and Receiver Characteristics
Table 70: PCI Express Interface Driver and Receiver Characteristics
Units
Notes
Baud rate
Description
Sym bol
BR
2.5
Gbps
-
Unit interval
UI
400.0
ps
-
Baud rate tolerance
Bppm
Min
Max
-300.0
300.0
ppm
2
Driver parameters
Differential peak to peak output voltage
VTXpp
0.8
1.2
V
-
Minimum TX eye w idth
TTXeye
0.75
-
UI
-
Differential return loss
TRLdiff
10.0
-
dB
1
Common mode return loss
TRLcm
6.0
-
dB
1
DC differential TX impedance
ZTXdiff
80.0
120.0
Ohm
-
Receiver parameters
Differential input peak to peak voltage
VRXpp
0.175
1.2
V
-
Minimum receiver eye w idth
TRXeye
0.4
-
UI
-
Differential return loss
RRLdiff
10.0
-
dB
1
Common mode return loss
RRLcm
6.0
-
dB
1
DC differential RX impedance
ZRXdiff
80.0
120.0
Ohm
-
DC common input impedance
ZRXcm
40.0
60.0
Ohm
-
Notes:
General Comment: For more information, refer to the PCI Express Base Specification, Revision 1.1, March, 2005.
1. Defined from 50 MHz to 1.25 GHz.
2. Does not account for SSC dictated variations.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 129
88F619x
Hardware Specifications
10.7.2.2
PCI Express Interface Test Circuit
Figure 46: PCI Express Interface Test Circuit
Test Points
+
C_TX
D+
D-
C_TX
50 ohm
50 ohm
When measuring Transmitter output parameters, C_TX is an optional portion of the
Test/Measurement load. When used, the value of C_TX must be in the range of 75 nF to 200 nF.
C_TX must not be used when the Test/Measurement load is placed in the Receiver package
reference plane.
Doc. No. MV-S104987-U0 Rev. F
Page 130
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications
Differential Interface Electrical Characteristics
10.7.3
SATA Interface Electrical Characteristics
The driver and receiver characteristics for the SATA-I Interface Gen1i Mode and the SATA-II
Interface Gen2i Mode are provided in the following sections.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 131
88F619x
Hardware Specifications
10.7.3.1
SATA-I Interface Gen1i Mode Driver and Receiver Characteristics
Table 71: SATA-I Interface Gen1i Mode Driver and Receiver Characteristics
Description
Sym bol
Baud Rate
Min
Max
1.5
BR
Units
Notes
Gbps
-
Baud rate tolerance
Bppm
-350.0
350.0
ppm
Spread spectrum modulation frequency
Fssc
30.0
33.0
kHz
-
Spread spectrum modulation Deviation
SSCtol
-5000.0
0.0
ppm
-
ps
-
Unit Interval
666.67
UI
Driver Parameters
Differential impedance
Zdifftx
85.0
115.0
Ohm
-
Single ended impedance
Zsetx
40.0
-
Ohm
-
Differential return loss (75 MHz-150 MHz)
RLOD
14.0
-
dB
-
Differential return loss (150 MHz-300 MHz)
RLOD
8.0
-
dB
-
Differential return loss (300 MHz-1.2 GHz)
RLOD
6.0
-
dB
-
Differential return loss (1.2 GHz-2.4 GHz)
RLOD
3.0
-
dB
-
Differential return loss (2.4 GHz-3.0 GHz)
RLOD
1.0
-
dB
-
Output differential voltage
Vdifftx
400.0
600.0
mV
2
1
Total jitter at connector data-data, 5UI
TJ5
-
0.355
UI
Deterministic jitter at connector data-data, 5UI
DJ5
-
0.175
UI
-
Total jitter at connector data-data, 250UI
TJ250
-
0.470
UI
1
Deterministic jitter at connector data-data, 250UI
DJ250
-
0.220
UI
-
Receiver Parameters
Differential impedance
Zdiffrx
85.0
115.0
Ohm
-
Single ended impedance
Zsetx
40.0
-
Ohm
-
Differential return loss (75 MHz-150 MHz)
RLID
18.0
-
dB
-
Differential return loss (150 MHz-300 MHz)
RLID
14.0
-
dB
-
Differential return loss (300 MHz-600 MHz)
RLID
10.0
-
dB
-
Differential return loss (600 MHz-1.2 GHz)
RLID
8.0
-
dB
-
Differential return loss (1.2 GHz-2.4 GHz)
RLID
3.0
-
dB
-
Differential return loss (2.4 GHz-3.0 GHz)
RLID
1.0
-
dB
-
Vdiffrx
325.0
600.0
mV
1
Input differential voltage
Total jitter at connector data-data, 5UI
TJ5
-
0.430
UI
Deterministic jitter at connector data-data, 5UI
DJ5
-
0.250
UI
-
Total jitter at connector data-data, 250UI
TJ250
-
0.600
UI
1
Deterministic jitter at connector data-data, 250UI
DJ250
-
0.350
UI
-
Notes:
General Comment: For more information, refer to SATA II Revision 2.6 Specification, February, 2007.
General Comment: The load is 100 ohm differential for these parameters, unless otherw ise specified.
General Comment: To comply w ith the values presented in this table, refer to your local
Marvell representative for register settings.
1. Total jitter is defined as TJ = (14 * RJσ) + DJ w here Rjσ is random jitter.
2. Output Differential Amplitude and Pre-Emphasis are configurabile. See functional register description
for more details.
Doc. No. MV-S104987-U0 Rev. F
Page 132
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications
Differential Interface Electrical Characteristics
10.7.3.2
SATA-II Interface Gen2i Mode Driver and Receiver Characteristics
Table 72: SATA-II Interface Gen2i Mode Driver and Receiver Characteristics
Description
Baud Rate
Baud rate tolerance
Sym bol
Min
Max
BR
Bppm
3.0
-350.0
350.0
Units
Notes
Gbps
-
ppm
-
Spread spectrum modulation frequency
Fssc
30.0
33.0
kHz
-
Spread spectrum modulation Deviation
SSCtol
-5000.0
0.0
ppm
-
ps
1,2
Unit Interval
UI
333.33
Driver Parameters
Output differential voltage
Vdifftx
400.0
700.0
mV
Differential return loss (150 MHz-300 MHz)
RLOD
14.0
-
dB
-
Differential return loss (300 MHz-600 MHz)
RLOD
8.0
-
dB
-
Differential return loss (600 MHz-2.4 GHz)
RLOD
6.0
-
dB
-
Differential return loss (2.4 GHz-3.0 GHz)
RLOD
3.0
-
dB
-
Differential return loss (3.0 GHz-5.0 GHz)
RLOD
1.0
-
dB
-
Total jitter at connector clock-data
TJ10
-
0.30
UI
3
Deterministic jitter at connector clock-data
DJ10
-
0.17
UI
3
Total jitter at connector clock-data
TJ500
-
0.37
UI
4
DJ500
-
0.19
UI
4
Vdiffrx
275.0
750.0
mV
5
Differential return loss (150 MHz-300 MHz)
RLID
18.0
-
dB
-
Differential return loss (300 MHz-600 MHz)
RLID
14.0
-
dB
-
Differential return loss (600 MHz-1.2 GHz)
RLID
10.0
-
dB
-
Differential return loss (1.2 GHz-2.4 GHz)
RLID
8.0
-
dB
-
Differential return loss (2.4 GHz-3.0 GHz)
RLID
3.0
-
dB
-
Differential return loss (3.0 GHz-5.0 GHz)
RLID
1.0
-
dB
-
Total jitter at connector clock-data
TJ10
-
0.46
UI
3
Deterministic jitter at connector clock-data
DJ10
-
0.35
UI
3
Total jitter at connector clock-data
TJ500
-
0.60
UI
4
Deterministic jitter at connector clock-data
DJ500
-
0.42
UI
4
Deterministic jitter at connector clock-data
Receiver Parameters
Input differential voltage
Notes:
General Comment: For more information, refer to SATA II Revision 2.6 Specification, February, 2007.
General Comment: The load is 100 ohm differential for these parameters, unless otherw ise specified.
General Comment: To comply w ith the values presented in this table, refer to your local
Marvell representative for register settings.
1. 0.45-0.55 UI is the range w here the signal meets the minimum level.
2. Output Differential Amplitude and Pre-Emphasis are configurabile. See functional register description
for more details.
3. Defined for BR/10.
4. Defined for BR/500.
5. 0.5 UI is the point w here the signal meets the minimum level.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 133
88F619x
Hardware Specifications
10.7.4
USB Electrical Characteristics
10.7.4.1
USB Driver and Receiver Characteristics
Table 73: USB Low Speed Driver and Receiver Characteristics
Low Speed
Description
Baud Rate
Baud rate tolerance
Ouput single ended high
Ouput single ended low
Output signal crossover voltage
Data fall time
Data rise time
Rise and fall time matching
Source jitter total: to next transition
Source jitter total: for paired transitions
Input single ended high
Input single ended low
Differential input sensitivity
Sym bol
BR
Bppm
Driver Parameters
VOH
VOL
VCRS
TLR
TLF
TLRFM
TUDJ1
TUDJ2
Receiver Parameters
VIH
VIL
VDI
Min
Max
1.5
-15000.0 15000.0
Units
Mbps
ppm
Notes
-
2.8
0.0
1.3
75.0
75.0
80.0
-95.0
-150.0
3.6
0.3
2.0
300.0
300.0
125.0
95.0
150.0
V
V
V
ns
ns
%
ns
ns
1
2
3
3, 4
3, 4
5
5
2.0
0.2
0.8
-
V
V
V
-
Notes:
General Comment: For more information, refer to Universal Serial Bus Specification, Revision 2.0, April 2000.
General Comment: The load is 100 ohm differential for these parameters, unless otherw ise specified.
General Comment: To comply w ith the values presented in this table, refer to your local
Marvell representative for register settings.
1. Defined w ith 1.425 kilohm pull-up resistor to 3.6V.
2. Defined w ith 14.25 kilohm pull-dow n resistor to ground.
3. See "Data Signal Rise and Fall Time" w aveform.
4. Defined from 10% to 90% for rise time and 90% to 10% for fall time.
5. Including frequency tolerance. Timing difference betw een the differential data signals.
Defined at crossover point of differential data signals.
Doc. No. MV-S104987-U0 Rev. F
Page 134
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications
Differential Interface Electrical Characteristics
Table 74: USB Full Speed Driver and Receiver Characteristics
Full Speed
Description
Sym bol
BR
Bppm
Driver Parameters
Ouput single ended high
VOH
Ouput single ended low
VOL
Output signal crossover voltage
VCRS
Output rise time
TFR
Output fall time
TFL
Source jitter total: to next transition
TDJ1
Source jitter total: for paired transitions
TDJ2
Source jitter for differential transition to SE0 transition
TFDEOP
Receiver Parameters
Input single ended high
VIH
Input single ended low
VIL
Differential input sensitivity
VDI
Receiver jitter : to next transition
tJR1
Receiver jitter: for paired transitions
tJR2
Baud Rate
Baud rate tolerance
Min
Max
12.0
-2500.0
2500.0
Units
Mbps
ppm
Notes
-
2.8
0.0
1.3
4.0
4.0
-3.5
-4.0
-2.0
3.6
0.3
2.0
20.0
20.0
3.5
4.0
5.0
V
V
V
ns
ns
ns
ns
ns
1
2
4
3, 4
3, 4
5, 6
5, 6
6
2.0
0.2
-18.5
-9.0
0.8
18.5
9.0
V
V
V
ns
ns
6
6
Notes:
General Comment: For more information, refer to Universal Serial Bus Specification, Revision 2.0, April 2000.
General Comment: The load is 100 ohm differential for these parameters, unless otherw ise specified.
General Comment: To comply w ith the values presented in this table, refer to your local
Marvell representative for register settings.
1.. Defined w ith 1.425 kilohm pull-up resistor to 3.6V.
2.. Defined w ith 14.25 kilohm pull-dow n resistor to ground.
3. Defined from 10% to 90% for rise time and 90% to 10% for fall time.
4. See "Data Signal Rise and Fall Time" w aveform.
5. Including frequency tolerance. Timing difference betw een the differential data signals.
6. Defined at crossover point of differential data signals.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 135
88F619x
Hardware Specifications
Table 75: USB High Speed Driver and Receiver Characteristics
High Speed
Description
Baud Rate
Baud rate tolerance
Data signaling high
Data signaling low
Data rise time
Data fall time
Data source jitter
Sym bol
BR
Bppm
Driver Parameters
VHSOH
VHSOL
THSR
THSF
Min
Max
480.0
-500.0
500.0
Units
Mbps
ppm
Notes
-
360.0
440.0
-10.0
10.0
500.0
500.0
See note 2
mV
mV
ps
ps
1
1
2
Receiver Parameters
Differential input signaling levels
Data signaling common mode voltage range
Receiver jitter tolerance
VHSCM
See note 3
-50.0
500.0
See note 3
3
3
mV
Notes:
General Comment: For more information, refer to Universal Serial Bus Specification, Revision 2.0, April 2000.
General Comment: The load is 100 ohm differential for these parameters, unless otherw ise specified.
General Comment: To comply w ith the values presented in this table, refer to your local
Marvell representative for register settings.
1. Defined from 10% to 90% for rise time and 90% to 10% for fall time.
2. Source jitter specified by the "TX eye diagram pattern template" figure.
3. Receiver jitter specified by the "RX eye diagram pattern template" figure.
10.7.4.2
USB Interface Driver Waveforms
Figure 47: Low/Full Speed Data Signal Rise and Fall Time
Rise Time
Fall Time
90%
90%
VCRS
10%
Differential
Data Lines
10%
TR
Doc. No. MV-S104987-U0 Rev. F
Page 136
TF
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Electrical Specifications
Differential Interface Electrical Characteristics
Figure 48: High Speed TX Eye Diagram Pattern Template
+525mV
+475mV
+400mV
Differential
+300mV
0 Volts
Differential
-300mV
- 400mV
Differential
-475mV
-525mV
7.5%
37.5%
92.5%
62.5%
0%
100%
Figure 49: High Speed RX Eye Diagram Pattern Template
+525mV
+475mV
+400mV
Differential
+175mV
0 Volts
Differential
-175mV
- 400mV
Differential
-475mV
-525mV
12.5%
35
65
0%
Copyright © 2008 Marvell
December 2, 2008, Preliminary
87.5%
100%
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 137
88F619x
Hardware Specifications
11
Thermal Data (Preliminary)
Table 76 provides the package thermal data for the device. This data is derived from simulations that
were run according to the JEDEC standard.
The thermal parameters are preliminary and subject to change.
Note
TET
The documents listed below provide a basic understanding of thermal management of integrated
circuits (ICs) and guidelines to ensure optimal operating conditions for Marvell products. Before
designing a system it is recommended to refer to these documents:
„
„
Application Note, AN-63 Thermal Management for Selected Marvell® Products, Document
Number MV-S300281-00
White Paper, ThetaJC, ThetaJA, and Temperature Calculations, Document Number
MV-S700019-00.
Table 76: Thermal Data for the 88F619x in the QFP 216-pin Package (Preliminary)
Sy m b o l
D e fin i ti on
Ai rf lo w Va lu e ( C / W )
0[m/s]
1 [ m /s ]
2 [ m /s ]
θJA
Thermal resistance: junction to ambient.
24.2
21.7
20.7
ΨJT
Thermal characterization parameter:
junction to case center.
1.04
1.16
1.26
θJC
Thermal resistance: junction to case (not air-flow dependent)
ΨJB
Thermal characterization parameter:
junction to the bottom of the package.
θJB
Thermal resistance:
junction to the bottom of the package (not air-flow dependent)
Doc. No. MV-S104987-U0 Rev. F
Page 138
9.7
11.84
11.95
11.93
16.1
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Package
12
Package
This section provides the 88F619x package drawing and dimensions.
Figure 50: LQFP 216-pin Package and Dimensions
1.
2.
3.
4.
5.
To be determined at seating plane —C—.
Dimensions D1 and E1 do not include mold
protrusions.
D1 and E1 are maximum plastic body size dimensions
including mold mismatch.
Dimension b does not include Dambar protrusions.
Dambar can not be located on the lower radius or the
foot.
Exact shape of each corner is optional.
These dimensions apply to the flat section of the lead
between 0.10 mm and 0.25 mm from the lead tip.
6.
7.
8.
9.
A1 is defined as the distance from the seating
plane to the lowest point of the package body.
Controlling dimension: millimeter.
Reference document: JEDEC MS-026
Special characteristics C class: ccc
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 139
88F619x
Hardware Specifications
Table 77: LQFP 216-pin Package Dimensions
Symbol
M in
D i m e ns i on in m m
N om i n a l
Max
Min
A
—
—
1.60
—
A1
0.05
—
0.15
A2
1.35
1.40
1.45
D im en s i on in i n c he s
Nominal
M ax
—
0.063
0.002
—
0.006
0.053
0.055
0.057
b
0.13
0.18
0.23
0.005
0.007
0.009
b1
0.13
0.16
0.19
0.005
0.006
0.007
c
0.09
0.14
0.20
0.004
0.006
0.008
c1
0.09
0.12
0.16
0.004
0.005
0.006
D
25.85
26.00
26.15
1.018
1.024
1.030
D1
23.90
24.00
24.10
0.941
0.945
0.949
E
25.85
26.00
26.15
1.018
1.024
1.030
E1
23.90
24.00
24.10
0.941
0.945
0.949
0.75
0.018
0.40 BSC
|e|
L
0.45
0.60
0.016 BSC
1.00 REF
L1
0.24
0.030
0.039 REF
R1
0.08
—
—
0.003
—
—
R2
0.08
—
—
0.003
—
—
S
0.20
—
—
0.008
—
—
θ
0o
3.5o
7o
0o
3.5o
7o
θ1
θ2
θ3
o
—
0
o
—
—
0
o
0
o
0
11
o
11
o
ccc
—
12
o
12
o
o
13
o
13
0.08
Table 78:
S y m b ol
13o
12
o
13o
0.003
LQFP 216-pin Package Exposed Pad (ePAD) Size
E x p os e d Pa d S i z e
mm
In c h e s
D2
5.715 REF
0.225 REF
E2
5.715 REF
0.225 REF
Doc. No. MV-S104987-U0 Rev. F
Page 140
12
o
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Part Order Numbering/Package Marking
Part Order Numbering
13
Part Order Numbering/Package Marking
13.1
Part Order Numbering
Figure 51 shows the part order numbering scheme for the 88F6190 and 88F6192. Refer to Marvell
Field Application Engineers (FAEs) or representatives for further information when ordering parts.
Figure 51: Sample Part Number
88F619x–xx–LGO2Cxxx–xxxx
Custom code (optional)
Part number
88F6190
88F6192
Speed code
060 = 600 MHz (88F6190)
080 = 800 MHz (88F6192)
Temperature code
C = Commercial
I = Industrial
Die revision
Environmental code
2 = Green (RoHS 6/6 and
Halogen-free)
Custom code
Package code
LGO = 216-pin LQFP
r
Table 79: Part Order Options
P a c k a g e Ty p e
P a r t O rd e r N u m b e r
216-pin LQFP
88F6190-xx-LGO2C060 (Green, RoHS 6/6 and Halogen-free package), 600 MHz
216-pin LQFP
88F6192-xx-LGO2C080 (Green, RoHS 6/6 and Halogen-free package), 800 MHz
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 141
88F619x
Hardware Specifications
13.2
Package Marking
Figure 52 shows a sample Commercial package marking and pin 1 location for the device.
Figure 52: Package Marking and Pin 1 Location
Marvell logo
Country of origin
(Contained in the mold ID or
marked as the last line on
the package.)
Part number and die revision
code
88F6-LGOe
Lot Number
YYWW xx@
Country of Origin
88F6190-xx
XXXX
88F6190 = Part number
Part number prefix, package code, environmental code
88F6 = Part number prefix
LGO = Package code
e = Environmental code: 2 = Green
Date code, custom code, assembly plant code
YYWW = Date code (YY = year, WW = Work Week)
xx = Custom code
@ = Assembly plant code
XX = Die revision
Pin 1 location
Temperature and speed code
C060 = Commercial, 600 MHz
88F6-LGOe
Part number and die revision
code
Lot Number
YYWW xx@
Country of Origin
88F6192-xx
XXXX
88F6192 = Part number
XX = Die revision
Temperature and speed code
C080 = Commercial, 800 MHz
Note: The above drawings are not drawn to scale. Location of markings is approximate.
Doc. No. MV-S104987-U0 Rev. F
Page 142
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Revision History
A
Table 80:
Revision History
Revision History
R e v i s io n
D a te
F
December 2, 2008
C o m m e n ts
Revision
1. For the 88F6190, added a Fast Ethernet port, in addition for the Gigabit Ethernet port.
2. In Figure 2, 88F6192 Pin Logic Diagram, on page 22:
• Changed the GE_TXCLKOUT pin to input/output and added a note under the figure, stating that the pin is an input
when used the MII/MMII Transmit Clock.
• Changed the name of pins GE_TXEN to GE_TXCTL and GE_RXDV to GE_RXCTL.
• Deleted the VDD_GE pin and replaced it with pins VDD_GE_A and VDD_GE_B. Also changed the VDD_GE pin to
VDD_GE_A/VDD_GE_B throughout the document.
3. In Table 4, Power Pin Assignments, on page 25, changed the name of the VDD_GE pin to VDD_GE_A and
VDD_GE_B and added new descriptions for those pins.
4. In Table 7, PCI Express Interface Pin Assignments, on page 30, revised the description of the PEX_CLK_P/N pins to
state that they can be configured as input or output according to the reset strap.
5.
•
•
•
In Table 9, 88F6190 Gigabit Ethernet Interface Pin Assignments, on page 32:
Revised most of the pin descriptions.
Revised the I/O designations for GE_TXCLKOUT and MPP[29]/GE1[9].
Changed the name of GE_TXEN to GE_TXCTL and GE_RXDV to GE_RXCTL.
6. In Table 10, 88F6192 Gigabit Ethernet Port0/1 Interface Pin Assignments, on page 34, indicated that:
• When the GE_TXCLKOUT pin is used as an MII/MMII Transmit Clock, it is an input pin.
• When the MPP[29]/GE1[9] pin is used as a GMII Transmit Clock, it is a Tri-State output pin.
7. In Table 14, RTC Interface Pin Assignments, on page 42, changed the type for RTC_XOUT to analog.
8. In the description of signal AU_SPDFRMCLK in Table 19, Audio (S/PDIF / I2S) Interface Signal Assignment, on
page 47, added a reference to the new AU_SPDFRMCLK information in the Reference Clock AC Timing
Specifications table.
9. In Table 26, Unused Interface Strapping, on page 56, revise the description for configuring the:
• MPP signals.
• PCI Express clock signals.
10. In Table 37, I/O and Core Voltages, on page 73, for the 88F6190, revise the I/O Voltage column to remove pin
VDD_GE and replace it with pins VDD_GE_A and VDD_GE_B.
11. In Figure 3, 88F6190 Pin Map Top View, on page 57 and Table 27, 88F6190 Pinout Sorted by Pin Number, on
page 58:
• Changed pins 18 and 25 from VDD_GE to VDD_GE_A.
• Changed pin 23 from GE_TXEN to GE_TXCTL and changed pin 27 from GE_RXDV to GE_RXCTL.
• Changed pins 40 and 47 from VDD_GE to VDD_GE_B.
12. In Table 32, 88F6190 Ethernet Ports Pins Multiplexing, on page 68, revised the RGMII column.
13. Revised the configurations options described in Section 6.2, Gigabit Ethernet (GbE) Pins Multiplexing on MPP,
on page 68 and added a note stating that all relevant Gigabit Ethernet signals must be implemented.
14. In Table 36, Supported Clock Combinations, on page 72, added a column showing the device number.
15. In Section 8.5, Pins Sample Configuration, on page 76, revised the note describing the pins with multiple voltage
options.
16. In Table 38, Reset Configuration, on page 77, revised the rows relating to the following signals:
MPP[2], MPP[3], MPP[5], MPP[10], MPP[12], MPP[19], MPP[33], NF_ALE, NF_REn, NF_CLE, NF_WEn.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 143
88F619x
Hardware Specifications
Table 80:
R e v i s io n
Revision History (Continued)
D a te
C o m m e n ts
17. In Table 42, Recommended Operating Conditions, on page 87:
• For the 88F6190, revised the VDD_GE pin to VDD_GE_A and added a separate row for VDD_GE_B.
• For parameter RTC_AVDD Analog supply for RTC in Battery Back-up mode, revised the values for the minimum to
1.3V from 1.4V and for the maximum to 1.7V from 1.6V.
18. In Table 43, Thermal Power Dissipation, on page 89, for the eFuse during Burning mode parameter added a note:
The eFuse burn is done once, and there should be no thermal effect, after it has been burned.
19. Revised the introduction to Section 10.5.2, RGMII, SMI and REF_CLK_XIN 1.8V (CMOS) DC Electrical Specifications,
on page 93.
20.
•
•
•
•
In Table 51, Reference Clock AC Timing Specifications, on page 97:
Revised the names of the Ethernet transmit symbols to FGE_TXCLK_OUT, DCGE_TXCLK_OUT, and SRGE_TXCLK_OUT.
Added the S/PDIF Recovered Master Clock.
Added the Transport Stream External Reference Clock.
For the PTP Reference Clock, revised the values for the Frequency, Duty Cycle, and Pk-Pk jitter parameters.
21. Revised the description of the power rails in the paragraph before Table 45, General 3.3V Interface (CMOS) DC
Electrical Specifications, on page 92.
22. Revised the description of the power rails in the paragraph before Table 46, RGMII 1.8V Interface (CMOS) DC
Electrical Specifications, on page 93.
E
October 5, 2008
Revision
1. In Table 38, Reset Configuration, on page 77, for CPU_CLK Frequency Select, revised the description of values 0x4
and 0x6.
2. In Table 7, PCI Express Interface Pin Assignments, on page 30, revised the note in the description of the
PEX_CLK_P/N pins.
3. In Table 26, Unused Interface Strapping, on page 56, added the eFuse strapping.
4. In Section 8.1.1, Power-Up Sequence Requirements, on page 73 and Section 8.1.2, Power-Down Sequence
Requirements, on page 74, added a power up/down requirements for when VHV is in eFuse Burning mode.
5. In Table 42, Recommended Operating Conditions, on page 87:
• For VHV, revised the two parameters to VHV (during eFuse Burning mode) and VHV (during eFuse Reading mode)
and added notes in the comments column for both VHV voltages.
• For VDD_M, PEX_AVDD, and USB_AVDD, revised the comments column.
• for RTC_AVDD, revised the values for minimum to 1.4V from 1.3V and for maximum to 1.6V from 1.7V.
6. In Table 43, Thermal Power Dissipation, on page 89, revised the row for the SDRAM and added a row for the eFuse.
7. In Table 44, Current Consumption, on page 91, revised the row for the SDRAM and added a row for the eFuse.
8. In Table 51, Reference Clock AC Timing Specifications, on page 97:
• For the CPU and Core Reference Clock frequency, revised the values.
• For the PTP Reference Clock, added the Slew rate and Pk-Pk jitter parameters.
D
August 18, 2008
Revision
1. Added the XOR engine to the block diagrams in the Product Overview on page 3.
2.
•
•
•
In Table 4, Power Pin Assignments, on page 25:
Changed the voltage for XTAL_AVDD from 2.5V to 1.8V.
Changed the voltage for SATA_AVDD (88F6190) and SATA0_AVDD/SATA1_AVDD (88F6192) from 2.5V to 3.3V.
Added pin VHV.
3. In Figure 1, 88F6190 Pin Logic Diagram, on page 21, Figure 2, 88F6192 Pin Logic Diagram, on page 22, and Table 7,
PCI Express Interface Pin Assignments, on page 30, changed PEX_CLK_P/N for input to input/output (I/O). Also
added VHV to both pin logic diagrams.
4. In Table 6, DDR SDRAM Interface Pin Assignments, on page 28, revised the description of M_NCASL and M_PCAL to
indicate the range of the resistor.
5. Added present and active pins to Table 8, SATA Port Interface Pin Assignment, on page 31.
Doc. No. MV-S104987-U0 Rev. F
Page 144
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Revision History
Table 80:
R e v i s io n
Revision History (Continued)
D a te
C o m m e n ts
6. In Section 2.2.6, Gigabit Ethernet Port Interface Pin Assignments, on page 32, added a note: For the TXCLK, use the
GE_RXCLK pin. Also indicated which pins are for port0 and which for port1.
7. Revised Table 21, Secure Digital Input/Output (SDIO) Interface Signal Assignment, on page 49 to indicate the pins
requiring pull up.
8. Added Table 23, Transport Stream (TS) Interface Signal Assignment, on page 52.
9. Added Section 2.2.20, Precise Timing Protocol (PTP) Interface, on page 54.
10. In Table 25, Internal Pull-up and Pull-down Pins, on page 55, changed pins GE_MDC, MPP[7] and MPP[18] from pull
down to pull up and removed MPP[13], MPP[15], and MPP[17] from the table, since they do not require a pull
up/down.
11. In Table 3, Unused Interface Strapping, on page 56, revised the description of the strapping for the SATA_AVDD pin in
the 88F6190 and the SATA0_AVDD/SATA1_AVDD pins in the 88F6192.
12.
•
•
•
In Section 6.1, Multi-Purpose Pins Functional Summary, on page 61:
Changed the MPP[6] row in the table to remove the 0x0 option.
Revised the description of SYSRST_OUTn.
Added a bullet: Pin MPP[6] wakes up after reset in 0x1 mode (SYSRST_OUTn)
13. In Section 6.3, TSMP (TS Multiplexing Pins) on MPP, on page 70, added to the description of the TSMP pins.
14. In Table 35, 88F619x Clocks, on page 71, added the PTP clock and changed references to the Core clock to be the
TCLK.
15. Revised Section 7.1, Spread Spectrum Clock Generator (SSCG), on page 72.
16. Revised Table 37, I/O and Core Voltages, on page 73.
17. In Section 8.2, Hardware Reset, on page 74, added SYSRST_OUTn to the list of pins that are still active during
SYSRSTn assertion.
18. Revised Section 8.2.1, Reset Out Signal, on page 75 and Section 8.2.3, SYSRSTn Duration Counter, on page 75 and
added Section 8.2.2, Power On Reset (POR), on page 75.
19. In Section 8.3.2, PCI Express Endpoint Reset, on page 76 revised the bulleted items.
20. Revised Section 8.5, Pins Sample Configuration, on page 76.
21. Made major revisions to Table 38, Reset Configuration, on page 77.
22. Revised the first two paragraphs in Section 8.6, Serial ROM Initialization, on page 80.
23. In Section 8.7, Boot Sequence, on page 81 revised the paragraph following step 4.
24. Revised Table 35, 88F619x Clocks, on page 71 and Table 36, Supported Clock Combinations, on page 72.
25. In Table 40, IDCODE Register Map, on page 84, revised the description of bits [31:28].
26.
27.
•
•
•
•
28.
In Table 41, Absolute Maximum Ratings, on page 85, revised the voltage for the SATA and XTAL AVDD pins.
In the Table 42, Recommended Operating Conditions, on page 87:
Revised the voltage for the SATA and XTAL AVDD pins
Added values for VDD_CPU and for the 3.3V interfaces
Revised the minimum value to 3.15V and the maximum value to 3.45V (+/-5%)
Revised the values for PEX_AVDD to minimum 1.7V, typical 1.8V, and maximum 1.9V.
In Section 10.3, Thermal Power Dissipation, on page 89, revised values for Core, PCI Express, USB, and SATA
parameters and revised the notes under the table.
29. In Section 10.4, Current Consumption, on page 91, revised values for the Core (including CPU), PCI Express, USB,
and SATA parameters and revised the notes under the table.
30. In Section 10.5.1, General 3.3V (CMOS) DC Electrical Specifications, on page 92, added reference to PTP and
RGMII.
31. Deleted Section 8.5.2 REF_CLK_XIN 2.5V (CMOS) DC Electrical Specifications and added pin REF_CLK_XIN to
Section 10.5.2, RGMII, SMI and REF_CLK_XIN 1.8V (CMOS) DC Electrical Specifications, on page 93, since the
power rail for the REF_CLK_XIN pin was changed from 2.5V to 1.8V.
32. Revised Table 51, Reference Clock AC Timing Specifications, on page 97.
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 145
88F619x
Hardware Specifications
Table 80:
R e v i s io n
Revision History (Continued)
D a te
C o m m e n ts
33. Revised Table 68, PCI Express Interface Differential Reference Clock Characteristics, on page 127 and Table 69, PCI
Express Interface Spread Spectrum Requirements, on page 128.
34. Revised Figure 28, TWSI Output Delay AC Timing Diagram, on page 113 so that it shows SDA tOV relative to the SCK
falling edge, as shown in the two tables that proceed the figure.
35. Revised all of Section 13, Part Order Numbering/Package Marking, on page 141.
C
June 16, 2008
Revision
1. Added information for the 88F6190 device throughout this specification. This includes the addition of two new sections:
Section 1, Overview, on page 18 and Section 4, 88F6190 Pinout, on page 57.
2. Added AN-249: Configuring the Marvell® SATA PHY to Transmit Predefined Test Patterns to the list of Related
Documentation on page 16.
3. In Table 4, Power Pin Assignments, on page 25, revised the description of VDD_GE_A and VDD_GE_B to add
additional information about RGMII. Also added pin VDD_GE for the 88F6190 and revised the description of VDD to
indicate that it provides the CPU voltage.
4. In Table 10, 88F6192 Gigabit Ethernet Port0/1 Interface Pin Assignments, on page 34, added a description for
MII/MMII to the GE_TXD[3:0], GE_TXCTL, GE_RXCTL, GE_RXCLK, GE_RXD[3:0] rows. Also for pin
MPP[30]/GE1[10] added a description for MII/MMII Receive Data Valid.
5. In Table 11, Serial Management Interface (SMI) Pin Assignments, on page 39 and in Table 16, MPP Interface Pin
Assignment, on page 44, revised the power rail information to indicate the power rail for each device.
6. In Table 19, Audio (S/PDIF / I2S) Interface Signal Assignment, on page 47 and Table 22, Time Division Multiplexing
(TDM) Interface Signal Assignment, on page 50, revised the power rail to VDD_GE_B.
7. In Section 6.1, Multi-Purpose Pins Functional Summary, on page 61:
• Changed all reference to MPP[0] and MPP[11] from GPI to GPIO.
• Added the following bullet at the end of the section, after the tables: When TWSI serial ROM initialization is enabled,
MPP[8] and MPP[9] wake up as TWSI data and clock pins, respectively.
8. Revised the supported clock combinations in Table 36, Supported Clock Combinations, on page 72.
9. Revised Section 6.2, Gigabit Ethernet (GbE) Pins Multiplexing on MPP, on page 68 to describe the differences in the
Gigabit Ethernet multiplexing for the 88F6190 and 88F6192.
10. Revised Table 32, 88F6190 Ethernet Ports Pins Multiplexing, on page 68 and Table 33, 88F6192 Ethernet Ports Pins
Multiplexing, on page 69 including the addition of a new configuration option for the Gigabit Ethernet ports: Port 0
MII/MMII, Port 1 RGMII.
11. In Table 35, 88F619x Clocks, on page 71, revised the PEX PHY and USB PHY PLL rows and added the PTP clock.
12. In Table 38, Reset Configuration, on page 77, revised the description of TWSI Serial ROM Initialization to indicate that
MPP[8] and MPP[9] wake up as TWSI data and clock pins, respectively.
13. In Table 41, Absolute Maximum Ratings, on page 85, Table 42, Recommended Operating Conditions, on page 87,
Table 43, Thermal Power Dissipation, on page 89, and Table 44, Current Consumption, on page 91, changed all
occurrences of VDD_CPU to VDD.
14. In Table 42, Recommended Operating Conditions, on page 87, revised the description of the VDD_GE_A/VDD_GE_B
row to show that RGMII can also operate with a voltage of 3.3V.
15. In Table 43, Thermal Power Dissipation, on page 89, added the row RGMII 3.3V interface.
16. In Table 44, Current Consumption, on page 91, revised the interface RGMII 1.8V interface to RGMII 1.8V or 3.3V
interface. Also added the parameter DDR2 SDRAM interface (On Board 16-bit 200 MHz).
17. Added Table 54, RGMII 10/100 AC Timing Table at 3.3V, on page 102.
B
April 8, 2008
Revision
1. In the features list, added the functional block diagram and the usage model diagram.
2. Throughout this specification, LVCMOS and LVTTL were changed to CMOS.
3. In Figure 2, 88F6192 Pin Logic Diagram, on page 22 revised the power pins section, changed the MPP pins to
MPP[35:0] from MPP[34:0] and removed the interfaces that are multiplexed on the MPP pins.
Doc. No. MV-S104987-U0 Rev. F
Page 146
Copyright © 2008 Marvell
Document Classification: Proprietary Information
December 2, 2008, Preliminary
Revision History
Table 80:
R e v i s io n
Revision History (Continued)
D a te
C o m m e n ts
4. Revised Table 2, Pin Functions and Assignments Table Key, on page 23 to show only terms relevant for this device.
5. In Table 4, Power Pin Assignments, on page 25, added pin SSCG_AVDD and added the SMI interface at 1.8V and the
MII/MMII interface at 3.3V to the description of the interfaces supported by pin VDD_GE_A.
6. In Table 10, 88F6192 Gigabit Ethernet Port0/1 Interface Pin Assignments, on page 34, removed pins GE_MDC and
GE_MDIO.
7. Added Section 2.2.7, Serial Management Interface (SMI) Interface Pin Assignments, on page 39, with a description of
the GE_MDC and GE_MDIO pins.
8. In Table 14, RTC Interface Pin Assignments, on page 42, changed the pin type for RTC_XIN to analog from CMOS.
9. In Table 17, Two-Wire Serial Interface (TWSI) Interface Pin Assignment, on page 45, changed the note to:
Requires a pull-up resistor to VDDO.
10. Added Section 3, Unused Interface Strapping, on page 56.
11. In Figure 4, 88F6192 Pin Map Top View, on page 59 and Table 28, 88F6192 Pinout Sorted by Pin Number, on
page 60:
• Changed pin 100 to MPP[16] from MPP[17].
• Changed pin 101 to MPP[17] from MPP[16].
• Changed pin 149 to PEX_AVDD from VSS.
12. In Table 35, 88F619x Clocks, on page 71, revised the description of CPU PLL to mention SSCG.
13. Added Section 7.1, Spread Spectrum Clock Generator (SSCG), on page 72.
14. Added Section 8.1, Power-Up/Down Sequence Requirements, on page 73 and revised the title of Section 8 to reflect
this changed.
15. In Section 8.4, Sheeva™ CPU TAP Controller Reset, on page 76, revised the note referring to sample at reset and
added the note: If a signal is pulled up on the board, it must be pulled to the proper voltage level. Certain reset
configuration pins are powered by VDD_GE_A and VDD_GE_B. Those pins have multiple voltage options (see
Table 42, Recommended Operating Conditions, on page 87).
16. In Table 41, Absolute Maximum Ratings, on page 85 and Table 42, Recommended Operating Conditions, on page 87,
added the parameter SSCG_VDD.
17. In Table 43, Thermal Power Dissipation, on page 89 added the following:
The purpose of the Thermal Power Dissipation table is to support system engineering in thermal design.
18. In Table 44, Current Consumption, on page 91 added the following:
The purpose of the Current Consumption table is to support board power design and power module selection.
19.
•
•
•
•
•
In Table 51, Reference Clock AC Timing Specifications, on page 97:
Revised the symbols for the Transport Stream (TS) output and input mode reference clocks
Revised the symbols for the SMI master mode reference clock
Revised the symbols for the TWSI master mode reference clock
Revised the description for symbol FRTC_XIN.
Removed the RGMII, GMII, MII 100 Mbps, and MII 10 Mbps rows from this table since they are not relevant to this
device.
20. In Table 71, SATA-I Interface Gen1i Mode Driver and Receiver Characteristics, on page 132, added driver and
receiver return loss parameters, according to updated standard.
21. In Table 64, Thermal Data for the 88F6190/88F6192 in the QFP 216-pin Package, on page 102, added values for all of
the parameters.
22. Replaced Figure 50, LQFP 216-pin Package and Dimensions, on page 139 with a revised package drawing,
revised Table 77, LQFP 216-pin Package Dimensions, on page 140, and added Table 78, LQFP 216-pin Package
Exposed Pad (ePAD) Size, on page 140.
A
January 28, 2008
Initial release
Copyright © 2008 Marvell
December 2, 2008, Preliminary
Doc. No. MV-S104987-U0 Rev. F
Document Classification: Proprietary Information
Page 147
THIS PAGE IS INTENTIONALLY LEFT BLANK.
Contact INFORMATION
Marvell Semiconductor, Inc.
5488 Marvell Lane
Santa Clara, CA 95054, USA
Tel: 1.408.222.2500
Fax: 1.408.752.9028
www.marvell.com
Marvell. Moving Forward Faster