SCHOTTKY BARRIER RECTIFIER 1N5820 THRU 1N5822 VOLTAGE RANGE 20 to 40 Volts CURRENT 3.0 Ampere FEATURES • • • • • DO-27 Fast switching Low forward voltage, high current capability Low power loss, high efficiency High current surge capability High temperature soldering guaranteed: 250℃/10 seconds,0.373″(9.5mm) lead length At 5 lbs.(2.3kg) tension MECHANICAL DATA • • • • • Case: Transfer molded plastic Epoxy: UL94V-0 rate flame retardant Polarity: Color band denoted cathode end Lead: Plated axial lead, solderable per MIL-STD-202E method 208C Mounting position: Any Weight: 0.042ounce, 1.19 gram Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • • • Ratings at 25℃ ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% SYMBOLS 1N5820 Maximum Repetitive Peak Reverse Voltage VRRM 20 Maximum RMS Voltage VRMS 14 Maximum DC Blocking Voltage VDC 20 Maximum Average Forward Rectified Current 0.375″(9.5mm) lead length at TL =95℃ Peak Forward Surge Current 8.3mS single half sine-wave superimposed on rated load (JEDEC method) 3.0A Maximum Instantaneous Forward Voltage (Note 1) at 9.4A TA = 25℃ Maximum DC Reverse Current at rated DC Blocking Voltage at (Note 1) T = 100℃ A Typical Junction Capacitance (NOTE 2) Typical Thermal Resistance (NOTE 3) Operation and Storage Temperature Range 1N5821 30 21 30 1N5822 40 28 40 UNIT Volts Volts Volts I(AV) 3.0 Amps IFSM 80 Amps VF IR CJ RθJL TJ .TSTG 0.475 0.850 0.500 0.900 0.5 20 250 15 (-55 to +125) 0.525 0.950 Notes: 1. Pulse test 300μs pulse width,1% duty cycle 2. Measured at 1.0MHz and applied reverse voltage of 4.0 Volts 3. Thermal resistance from junction to ambient P.C.B .mounted with 0.375”(9.5mm)lead length with 2.5”×2.5“ （63.5×63.5mm）copper pads E-mail: [email protected] Web Site: www.cnmic.com Volts mA pF ℃/W ℃ SCHOTTKY BARRIER RECTIFIER 1N5820 THRU 1N5822 VOLTAGE RANGE 20 to 40 Volts CURRENT 3.0 Ampere RATING AND CHRACTERISTIC CURVES 1N5820 THRU 1N5822 FIG.1-TYPICAL FORWARD CURRENT FIG.2-MAXIMUM NON-REPETITIVE PEAK DERATING CURVE FORWARD SURGE CURRENT 100 2.0 1.0 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375″(9.5mm) Lead Length 8.3ms Single Half Sine-Wave (JEDEC Method) Tj =Tjmax CURRENT, (A) PEAK FORWARD SURGE AVERAGE FORWARD CURRENT, (A) 3.0 50 1 Cycle 0 0 20 40 60 95100 80 120 140 10 0.1 100 10 AMBIENT TEMPERATURE, (° C) NUMBER OF CYCLES AT 60 Hz FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG.4-TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, (mA) TJ =125° C 10 T =25° C (A) INSTANTANEOUS FORWARD CURRENT, 100 1.0 PULSE WIDTH=300μs DUTY CYCLE 1% 0.1 0.01 0 0.2 0.4 0.6 0.8 1.0 1.2 10 TJ =125° C 1.0 TJ =75° C TJ =25° C 0.1 0.01 1.4 0 INSTANTANEOUS FORWARD VOLTAGE,(V) 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) FIG.5-TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE,(pF) 1000 100 TJ =25° C f=1MHz Vsig=50mV 10 0.1 1.0 10 100 REVERSE VOLTAGE,(V) E-mail: [email protected] Web Site: www.cnmic.com 120 140