FAST RECOVERY RECTIFIER FR801 THRU FR806 VOLTAGE RANGE 50 to 1000 Volts CURRENT 8.0 Ampere FEATURES • • • • • • • • TO-220AC Glass passivated chip junction Low cost construction Fast switching for high efficiency Low reverse leakage High forward surge current capacity High temperature soldering guaranteed 260℃/10 second,0.375″(9.5mm)lead length at 5 lbs (2.3kg) tension MECHANICAL DATA • • • • • • Case: Transfer molded plastic Epoxy: UL94V-0 rate flame retardant Polarity: Color band denotes cathode end Lead: Plated axial lead, solderable per MIL-STD-202E method 208C Mounting position: Any Weight: 0.064ounce, 1.81 gram Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • • • Ratings at 25℃ ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% SYMBOLS FR801 FR802 Maximum Repetitive Peak Reverse Voltage VRRM 50 100 Maximum RMS Voltage VRMS 35 70 Maximum DC Blocking Voltage VDC 50 100 Maximum Average Forward Rectified Current 0.375″(9.5mm) lead length at Tc=100℃ Peak Forward Surge Current 8.3ms single half sine wave superimposed on rated load (JEDEC method) FR803 200 140 200 FR804 400 280 400 FR805 600 420 600 FR806 800 560 800 UNIT Volts Volts Volts I(AV) 8.0 Amps IFSM 200 Amps Maximum Instantaneous Forward Voltage at 8.0A VF IR 1.3 10 500 Volts Maximum DC Reverse Current at rated TA = 25℃ DC Blocking Voltage per element TA = 100℃ Maximum Reverse Recovery Time (NOTE 3)Tj=25℃ Typical Junction Capacitance (NOTE 1) Typical Thermal Resistance (NOTE 2) Operating and Storage Temperature Range Storage Temperature Range trr CJ RθJC TJ TSTG 150 250 50 3.0 (-55 to +150) (-55 to +150) Notes: 1. Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts. 2. Thermal Resistance from Junction to CASE 3. Reverse Recovery Test Conditions: IF =0.5A, IR =1.0A, IRR =0.25A E-mail: [email protected] Web Site: www.cnmic.com µA 500 nS pF ℃/W ℃ ℃ FAST RECOVERY RECTIFIER FR801 THRU FR806 VOLTAGE RANGE 50 to 1000 Volts CURRENT 8.0 Ampere RATING AND CHRACTERISTIC CURVES FR801G THRU FR806 FIG.1-TYPICAL FORWARD CURRENT FIG.2-MAXIMUM NON-REPETITIVE PEAK DERATING CURVE FORWARD SURGE CURRENT Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375″(9.5mm) Lead Length (A) 8.0 4.0 300 CURRENT, (A) PEAK FORWARD SURGE AVERAGE FORWARD CURRENT, 12.0 8.3ms Single Half Sine-Wave (JEDEC Method) T= T jmax 200 100 1 Cycle 0 0 25 50 100 75 125 175 150 0 1 2 AMBIENT TEMPERATURE, (° C) 4 FIG.3-TYPICAL INSTANTANEOUS 0.1 TJ =25° C Pulse Width=300us 1% Duty Cycle 0.8 1.0 1.2 1.4 1.6 40 20 60 80 100 10 TJ =100° C 1 (μA) INSTANTANEOUS REVERSE CURRENT, 1.0 (A) INSTANTANEOUS FORWARD CURRENT, 20 10 0.6 8 10 FIG.4-TYPICAL REVERSE CHARACTERISTICS FORWARD CHARACTERISTICS 0.01 0.4 6 NUMBER OF CYCLES AT 60 Hz TJ =25° C 0.1 0.01 1.8 0 20 INSTANTANEOUS FORWARD VOLTAGE,(V) 40 60 100 80 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) FIG.5-TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE,(pF) 1000 F1G.6-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC Trr 50Ω 10Ω NONINDUCTIVE NONINDUCTIVE +0.5A (-) 100 (+) 25 Vdc (approx.) (-) T J =25° C f=1MHz Vsig=50mVp-p 1.0 1Ω NON INDUCTIVE PULSE GENERATIOR (NOTE 2) 0 -0.25A (+) OSCILLOSCOPE (NOTE 1) -1.0A 10 0.1 D.U.T. 10 100 REVERSE VOLTAGE,(V) E-mail: [email protected] NOTES : 1.Rise Time=7ns mas. Input Impedance= 1 magohm. 22pF 2.Rise time=10ns max. Source Impedance= 50 ohms Web Site: www.cnmic.com 1cm SET TIME BASE FOR 50/100ns/cm