R1200F HIGH VOLTAGE SILICON RECTIFIER VOLTAGE RANGE 1200 to 5000 Volts R5000F CURRENT 0.2 - 0.5 Amperes THRU FEATURES Fast switching Low leakage High surge capability High current capability High temperature soldering guaranteed: 260/10 seconds. 0.375" (9.5mm) lead length at 5lbs. (2.3kg) tension. MECHANICAL DATA Case: Transfer molded plastic Epoxy: UL94V - 0 rate flame retardant Polarity: Color band denotes cathode end. Lead: Plated slug, solderable per MIL - STD 202 E method 208C Mounting position: Any Weight: 0.012 ounce, 0.33grams (DO-41) 0.014 ounce, 0.39 grams (DO-15) (R2500F - R5000F) (R1200F - R200 MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 ambient temperature unless otherwise specified Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load derate current by 20% Maximum Repetitive Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current, 0.375" (9.5mm) Lead length at TA = 50 Peak Forward Surge Current 8.3ms single half sine - wave superimposed on rated load (JEDEC method ) Maximum Instantaneous Forward Voltage Drop at 0.5A / 0.2A Maximum DC Reverse Current at rated DC blocking voltage TA = 25 Maximum Full Load Reverse Current, full cycle average 0.375" (9.5mm) lead length at TA = 55 Maximum Reverse Recovery Time (Note 1)` Operating and Storage Temperature Range SYMBOLS R1200FR1500FR1800FR2000FR2500FR3000FR4000FR5000FUNIT VRRM 1200 Volts VRMS 840 Volts VDC 1200 Volts I(AV) IFSM VF 500 mA 30 IR IR(AV) trr TJ, TSTG (-65 to +150) Amps Volts A NOTES: 1. Test condition : IF = 0.5A, IR = 1.0A, Irr = 0.25A MIC INVESTMENTS (CHINA) COMPANY LIMITED nS RATINGS AND CHARACTERISTIC CURVES R1200F THRU R5000F FIG.2-MAXIMUM NON-REPETITIVE PEAK FIG.1-TYPICAL FORWARD CURRENT FORWARD SURGE CURRENT Single Phase Half Wave 60Hz Inductive Load 0.375"(9.5mm) Lead Length 200 R25 00F -R5 20 0F -R 20 00 F 000 F 8.3ms Single Half Sine-Wave =TT j j max (JEDEC Method) CURRENT, (A) Resistive or R1 30 PEAK FORWARD SURGE 500 (mA) AVERAGE FORWARD CURRENT, DERATING CURVE 20 10 1 Cycle 0 0 25 50 75 100 125 150 175 0 1 AMBIENT TEMPERATURE, ( ° C) 2 4 6 8 10 20 40 60 NUMBER OF CYCLES AT 60 Hz FIG.3-TYPICAL REVERSE CHARACTERISTICS FIG.4-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 1.0 Trr 50 NONINDUCTIVE +0.5A 10 NONINDUCTIVE (A) INSTANTANEOUS REVERSE CURRENT, 10 (-) (+) 25 Vdc (approx.) 0.1 Tj =25 ° C (-) D.U.T. 1 NON INDUCTIVE PULSE GENERATIOR (NOTE 2) 0 -0.25A (+) OSCILLOSCOPE (NOTE 1) -1.0A 1cm 0.01 0 40 80 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) 120 NOTES: 1.Rise Time =7ns max. Input Impedance= 1 megohm. 22pF 2.Rise time=10ns max. Source Impedance= 50 ohms SET TIME BASE FOR 50/100ns/cm 100