0.05-4.0 GHz Dual High Dynamic Range Amplifier XG1001-SA January 2010 - Rev 12-Jan-10 Features Matched Pair of Amplifiers for Optimum Balanced Design Input 1 Output 1 0.05 to 4.0 GHz Frequency Range 44 dBm Output IP3 (Balanced configuration) 41 dBm Output IP3 (Single-ended configuration) N/C N/C 13 dB Gain @ 2 GHz N/C N/C 22.5 dBm P1dBm 2.1 dB Noise Figure Input 2 Output 2 RoHS Compliant SOIC-8 Package Single Positive Supply Backside slug is source GND +3V to +5V Voltage Rail Absolute Maximum Ratings General Description The XG1001-SA is a dual high dynamic range amplifier designed for applications operation within the 0.05 to 4.0 GHz frequency range. Co-located matched amplifiers are assembled in an RoHS compliant SOIC-8 package. The XG1001-SA is an ideal solution for implementing balanced or push-pull designs. The amplifier can also be used for dual-band operation where single-ended design is used for each band. The amplifier has the flexibility of being optimized for a number of wireless applications. The combination of low noise figure and high IP3 at the same bias point make it an ideal transmit or receive solution when used in applications including CATV operating from 50 to 850 MHz, cellular and PCS (personal communications service) operating from 0.8 to 2.2 GHz; MMDS (multichannel multipoint distribution systems) operating from 2.2 to 2.7 GHz; and WLAN (wireless LAN) operation at 2.4 GHz. All devices are 100% RF and DC tested. Supply Voltage RF Input Power* Storage Temperature (Tstg) Junction Temperature Operating Temperature Thermal Resistance +6.0 V +20 dBm -55 ºC to +125 ºC 150 ºC -40 ºC to +85ºC 27 ºC/W Operation of this device above any of these parameters may cause damage. *Operation with more than 10 dBm of input power may cause 2 dB degradation in OIP3 performance. Typical Parameters Electrical Characteristics (T = 25ºC) Parameter Typical 0.9 Frequency Range 14.5 Gain -13 Input Return Loss Output Return Loss -16 42 Output IP3 2.1 Noise Figure +22.5 Output P1dB Units 2 2.4 GHz 13 12 dB -14.5 -20 dB -15.4 -11 dB 41 40.5 dBm 2.1 2.6 dB +22.5 +22.5 dBm Typical values reflect performance in recommended application circuit @ +5V. Unless otherwise specified, the following specifications are guaranteed at room temerpature in a Mimix fixture. Parameter Frequency Range Gain Input Return Loss Output Return Loss Output IP3 Noise Figure Output P1dB Operating Current Range Supply Voltage Condition Externally Matched Externally Matched Externally Matched Units GHz dB dB dB dBm dB dBm mA V Min. 0.05 11.5 38 120 Typ. 13 -10 -10 41 2.1 22.5 160 5.0 Max. 4.0 200 Notes: 1. T = 25ºC, Frequency = 2 GHz, 50 Ohm system. 2. Each single ended amplifier is tested separately. 3. OIP3 is measured with two tones at output power of 5 dBm/tone separated by 10 MHz. 4. Slight performance degredation is expected over temperature. Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 1 of 6 Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 0.05-4.0 GHz Dual High Dynamic Range Amplifier XG1001-SA January 2010 - Rev 12-Jan-10 Application Circuit @ 1.9 GHz ~ 2.1 GHz: Schematic Typical Performance XG1001-SA: Gain XG1001-SA: 5V, 150mA, Single-ended 20 15 15 5 S11 0 S22 14 S21 (dB) (dB) 10 S21 -5 S12 -10 -15 -20 13 12 11 -25 -30 0 0.5 1 1.5 2 2.5 Frequency (GHz) 3 10 1.7 1.8 1.9 2 2.1 2.2 Frequency (GHz) Parameter Typ Typ Typ Units Frequency Range 1.9 2.0 2.1 GHz Gain 13 12.8 12.0 dB Input Retrun Loss -14 -14.5 -14.0 dB Output Return Loss -17 -15.4 -15 dB Output IP3 40.5 40.1 40.0 dBm Noise Figure 2.2 2.2 2.2 dB Output P1dB 22.5 22.5 22.6 dBm Components Ref Designator C2, C4, C6, C8 C1, C5 C3, C7 L1, L2 Value Size 100 pf 0402 1.0 pf 0603 1000 pf 0805 47 nH 0805 Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 2 of 6 Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 0.05-4.0 GHz Dual High Dynamic Range Amplifier XG1001-SA May 2008 - Rev 14-May-08 January 2010 - Rev 12-Jan-10 Functional Block Diagram Input 1 Pin Out Detail Output 1 N/C N/C N/C N/C Input 2 Pin Function Description 1 IN 1 Amplifier 1 RF input 4 IN 2 Amplifier 2 RF input 5 OUT 2 Amplifier 1 RF Output 8 OUT 1 Amplifier 2 RF Output 2,3,6,7 N/C Output 2 Backside slug is source GND Land Pattern It is recommended that all N/C pins be grounded and sufficient number of plated thru vias be added under the ground plane to insure RF stability and good thermal grounding. Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 3 of 6 Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 0.05-4.0 GHz Dual High Dynamic Range Amplifier XG1001-SA January 2010 - Rev 12-Jan-10 Physical Dimensions Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 4 of 6 Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 0.05-4.0 GHz Dual High Dynamic Range Amplifier XG1001-SA January 2010 - Rev 12-Jan-10 MTTF These numbers were calculated based on accelerated life test information received from the fabrication foundry and measured thermal resistance. XG1001-SA Vd=5.0 V, Id=300 mA MTTF (hours) 1.0E+09 1.0E+08 1.0E+07 1.0E+06 60 70 80 90 100 110 Backplate Temperature (deg C) XG1001-SA Vd=5.0 V, Id=300 mA 160 140 Tch (deg C) 120 100 80 60 40 20 0 40 50 60 70 80 90 100 110 Backplate Temperature (deg C) Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 5 of 6 Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 0.05-4.0 GHz Dual High Dynamic Range Amplifier XG1001-SA January 2010 - Rev 12-Jan-10 Handling and Assembly Information CAUTION! - Mimix Broadband MMIC Products contain gallium arsenide (GaAs) which can be hazardous to the human body and the environment. For safety, observe the following procedures: Do not ingest. Do not alter the form of this product into a gas, powder, or liquid through burning, crushing, or chemical processing as these by-products are dangerous to the human body if inhaled, ingested, or swallowed. Observe government laws and company regulations when discarding this product. This product must be discarded in accordance with methods specified by applicable hazardous waste procedures. Life Support Policy - Mimix Broadband's products are not authorized for use as critical components in life support devices or systems without the express written approval of the President and General Counsel of Mimix Broadband. As used herein: (1) Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. (2) A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Package Attachment - This packaged product from Mimix Broadband is provided as a rugged surface mount package compatible with high volume solder installation. Care should be taken not to apply heavy pressure to the top or base material to avoid package damage. Vacuum tools or other suitable pick and place equipment may be used to pick and place this part. Care should be taken to ensure that there are no voids or gaps in the solder connection so that good RF, DC and ground connections are maintained. Voids or gaps can eventually lead not only to RF performance degradation, but reduced reliability and life of the product due to thermal stress. Mimix Lead-Free RoHS Compliant Program - Mimix has an active program in place to meet customer and governmental requirements for eliminating lead (Pb) and other environmentally hazardous materials from our products. All Mimix RoHS compliant components are form, fit and functional replacements for their non-RoHS equivalents. Lead plating of our RoHS compliant parts is 100% matte tin (Sn) over copper alloy and is backwards compatible with current standard SnPb low-temperature reflow processes as well as higher temperature (260°C reflow) “Pb Free” processes. Ordering Information Part Number for Ordering Description XG1001-SA-0G00 XG1001-SA-0G0T Matte Tin plated RoHS compliant SOIC-8 surface mount package in bulk quantity Matte Tin plated RoHS compliant SOIC-8 surface mount package in tape and reel PB-XG1001-SA-00A0 PB-XG1001-SA-00B0 PB-XG1001-SA-00C0 XG1001-SA Evaluation Board @ 900 MHz XG1001-SA Evaluation Board @ 1.9 GHz~2.1 GHz XG1001-SA Evaluation Board @ 2.4 GHz We also offer this product with SnPb (Tin-Lead) or NiPdAu plating. Please contact your regional sales manager for more information regarding different plating types. Caution: ESD Sensitive Appropriate precautions in handling, packaging and testing devices must be observed. Proper ESD procedures should be followed when handling this device. Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 6 of 6 Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws.