MINILOGIC ML6209

ML6209
ML6209 Series - High Speed LDO Regulators
(low ESR capacitor compatible, ON/OFF switch)
CMOS Low Power Consumption
Dropout Voltage:
Mobile phones
200mV @ 100mA
Maximum Output Current:
150mA
Cordless phones
Cameras, video recorders
Highly Accurate: 1.5V ~ 1.95V ± 3%
2.0V ~ 6.00V ± 2%
Output Voltage Range: 1.5V ~ 6.0V
Low ESR capacitor compatible
Portable games
Portable AV equipment
Reference voltage
Battery-powered equipment
60mV @ 30mA,
◆ Applications
◆ General Description
◆ Features
The ML6209 series are highly precise, low noise, positive voltage LDO
Maximum Output Current: 150mA
regulators manufactured using CMOS process. The series achieves high
Dropout Voltage: 200mV (IOUT = 100mA)
ripple rejection and low dropout and consists of a standard voltage
Maximum Operating Voltage: 10V
source, an error correction, current limiter and a phase compensation
Output Voltage Range: 1.5V ~ 6.0V in 50mV increments
circuit plus a driver transistor. Output voltage is selectable in 50mV
increments within a range of 1.5V ~ 6.0V.
The series is also compatible with low ESR ceramic capacitors which give
added output stability. This stability can be maintained even during load
fluctuations due to the excellent transient response of the series. The CE
function enables the output to be turned off, resulting in greatly reduced
Highly Accurate: ± 2%
Low Power Consumption: TYP 25µA
Standby Current: less than 0.1µA
High Ripple Rejection: 70dB (10 kHz)
Low Output Noise: 30µVrms
Operational Temperature Range: -40°C ~ +85°C
power consumption.
Low ESR Capacitor Compatible: Ceramic capacitor
◆ Typical Application
P1/14
Rev. A, March 2006
ML6209
◆ Pin Assignment
◆ Pin Function
Pin No.
SOT-23-5
Pin Name
Description
SOT-23-5
SOT-89-5
1
4
VIN
Input
2
2
VSS
Ground
3
3
CE
ON/OFF Control
4
1
N.C.
No Connection
5
5
VOUT
Output
SOT-89-5
◆ Product Classification
Selection Guide
The following options for the CE pin logic and internal pull-up/down are available:
Active 'High' + no pull-down resistor built-in (standard)
Active 'High' + 800kΩ pull-down resistor built-in <between CE-VSS> (semi-custom)
Active 'Low' + no pull-up resistor built-in (semi-custom)
Active 'Low' + 800kΩ pull-up resistor built-in <between CE-VSS> (semi-custom)
Note: *With the pull-up resistor or pull-down resistor built-in types, the supply current during operation will increase by VIN / 800kΩ (TYP.)
Ordering Information
ML62091234567
Designator
Symbol
1
23
Description
A
Active “High” (pull-down resistor built in)
B
Active “High” (no pull-down resistor built in)
C
Active “Low” (pull-up resistor built in)
D
Active “Low” (no pull-up resistor built in)
15 ~ 60
Output Voltage:
e.g. 20 ⇒ 2.0V, 30 ⇒ 3.0V etc.
2
Output Voltage: 100mV increments, ± 2% accuracy
e.g.2=3,3=8, 4=2 ⇒ 3.8V, ± 2%
A
Output Voltage: 50mV increments, ± 2% accuracy
e.g. 2=3,3=8, 4=A ⇒ 3.85V, ± 2%
M
SOT-23-5 Package
P
SOT-89-5 Package
R
Embossed Tape: Standard Feed
L
Embossed Tape: Reverse Feed
G
Lead-free Package
4
5
6
7
Please note that “B” version is the standard part while the A, C and D are semi-custom parts.
P2/14
Rev. A, March 2006
ML6209
◆ Marking Information
SOT-23-5
1represents the product name
(TOP VIEW)
SOT-89-5
Designator
Product Name
P
ML6209*******
2 represents the integer part of the output voltage
Designator
Output voltage (V)
1
1.0
2
2.0
3
3.0
4
4.0
5
5.0
6
6.0
(TOP VIEW)
3represents the decimal part of the output voltage
Designator
Output Voltage
(V)
Designator
Output voltage
(V)
0
0.0
A
0.05
1
0.1
B
0.15
2
0.2
C
0.25
3
0.3
D
0.35
4
0.4
E
0.45
5
0.5
F
0.55
6
0.6
G
0.65
7
0.7
H
0.75
8
0.8
I
0.85
9
0.9
J
0.95
e.g. 23=12 ⇒ 1.20V and 23=1C ⇒ 1.25V.
4 represents the resistor version
Designator
Resistor Version
A
Active “High” (pull-down resistor built in)
B
Active “High” (no pull-down resistor built in)
C
Active “Low” (pull-up resistor built in)
D
Active “Low” (no pull-up resistor built in)
P3/14
Rev. A, March 2006
ML6209
◆ Package Information
SOT-23-5
P4/14
Rev. A, March 2006
ML6209
◆ Package Information
SOT-89-5
P5/14
Rev. A, March 2006
ML6209
◆ Block Diagram
The diodes in the circuit above are the protective diodes.
◆ Absolute Maximum Ratings
Parameter
Symbol
Ratings
Units
Input Voltage
VIN
10
V
Output Current
IOUT
400
mA
Output Voltage
VOUT
VSS-0.3 ~ VIN+0.3
V
Power Dissipation SOT25
Pd
250
mW
Operation Ambient Temperature
Topr
-40 ~ +70
˚C
Storage Temperature
Tstg
-55 ~ +80
˚C
* IOUT= the range of Pd/(VIN-VOUT)
P6/14
Rev. A, March 2006
ML6209
◆ Electrical Characteristics
ML6209A, B Series
Parameter
Output Voltage
Maximum Output Current
Load Regulation
Dropout Voltage
Supply Current (A series)
Supply Current (B series)
Standby Current
Symbol
Conditions
VOUT(E)
IOUT = 30mA,
1.5V ≤VOUT(T) ≤ 1.95V
IOUT = 30mA,
2.0V ≤VOUT(T) ≤ 6.0V
IOUT MAX
∆VOUT
Vdif1
Vdif2
IDD
Input Voltage
Output Voltage
Temp. Characteristics
Istby
∆VOUT
∆VIN-VOUT
VIN
∆VOUT
∆Topr-VOUT
Output Noise
en
Ripple Rejection Rate
PSRR
Current Limited
Short-circuit Current
CE ”High” Voltage
CE ”Low” Voltage
CE ”High” Current
(A series)
CE ”High” Current
(B series)
CE “Low” Current
Line Regulation
Min
Ta=25°°C
Typ
Max
-40°°C ≤ Ta ≤ 85°°C
Units Circuit
Min
Typ
Max
X0.97 VOUT(T) X1.03 X0.96 VOUT(T) X1.04
150
1mA ≤ IOUT ≤ 100mA
IOUT = 30mA
IOUT = 100mA
VIN=VCE=VOUT(T)+1.0V
VIN=VCE=VOUT(T)+1.0V
VIN=OUT(T)+1.0V, VCE=VSS
VOUT(T)+1.0V≤ VIN≤ 10V
IOUT=30mA
V
1
mA
mV
mV
mV
1
1
µA
2
µA
2
X0.98 VOUT(T) X1.02 X0.97 VOUT(T) X1.03
150
15
50
30
80
28
28
0.05
44
44
1.00
0.05
0.30
%/V
1
10
V
Ppm/
°C
--
µVrms
3
E-1
E-2
20
20
25
25
0.01
40
40
0.10
0.01
0.20
2
IOUT=30mA
-40°C≤ Topr≤ 85°C
IOUT=10mA
300Hz ~ 50kHz
10
20
20
2
100
30
VIN=[VOUT(T)+1.0]V+1.0Vp-pAC
IOUT=50mA, f=10kHz
70
IIim
Ishort
VCEH
VCEL
VIN=VOUT(T)+1.0V, VCE=VIN
VIN=VOUT(T)+1.0V, VCE=VIN
300
50
ICEH
VIN=VCE=VOUT(T)+1.0V
280
60
1
1
dB
4
1
1
1
1
1.6
VIN
0.25
1.7
VIN
0.20
mA
mA
V
V
-0.10
20
-0.15
25
µA
2
ICEH
VIN=VCE=VOUT(T)+1.0V
-0.10
0.10
-0.15
0.15
µA
2
ICEL
VIN =VOUT(T)+1.0V, VCE=VSS
-0.10
0.10
-0.15
0.15
µA
2
Note
(NOTE 1) Unless otherwise stated, VIN =VOUT(T) +1.0V
(NOTE 2) VOUT(T)=Specified Output Voltage
(NOTE 3) VOUT(E)=Effective Output Voltage (I.e. the output voltage when “VOUT(T)+1.0V” is provided at the VIN pin while maintaining a certain
IOUT value)
(NOTE 4) Vdif= (VIN1 (NOTE6) – VOUT1 (NOTE5))
(NOTE 5) VOUT1=A voltage equal to 98% of the Output Voltage whenever an amply stabilized IOUT (VOUT(T)+1.0V) is input.
(NOTE 6) VIN1=The Input Voltage when VOUT1 appears as Input Voltage is gradually decreased.
(NOTE 7) The values for -40°C ≤ Topr ≤ 85°C are designed values.
P7/14
Rev. A, March 2006
ML6209
ML6209C, D Series
Parameter
Symbol
Conditions
Output Voltage
VOUT(E)
IOUT = 30mA,
1.5V ≤VOUT(T) ≤ 1.95V
IOUT = 30mA,
2.0V ≤VOUT(T) ≤ 6.0V
Maximum Output Current
Load Regulation
Dropout Voltage
Supply Current (C series)
Supply Current (B series)
Standby Current
IOUT MAX
∆VOUT
Vdif1
Vdif2
IDD
Input Voltage
Output Voltage
Temp. Characteristics
Istby
∆VOUT
∆VIN-VOUT
VIN
∆VOUT
∆Topr-VOUT
Output Noise
en
Line Regulation
Min
Ta=25°°C
Typ
Max
-40°°C ≤ Ta ≤ 85°°C
Units
Min
Typ
Max
X0.97 VOUT(T) X1.03 X0.96 VOUT(T) X1.04
150
15
20
20
25
25
0.01
40
40
0.10
0.01
0.20
2
10
70
IIim
Ishort
VCEH
VCEL
ICEH
VIN=VOUT(T)+1.0V, VCE=VSS
VIN=VOUT(T)+1.0V, VCE=VSS
VIN=VCE=VOUT(T)+1.0V
ICEL
VIN =VOUT(T)+1.0V, VCE=VSS
ICEL
VIN =VOUT(T)+1.0V, VCE=VSS
20
20
1
mA
mV
mV
mV
1
1
µA
2
1.6
44
44
1.00
µA
2
0.05
0.30
%/V
1
10
V
Ppm/
°C
--
µVrms
3
2
280
60
1.7
1
28
28
0.05
30
300
50
PSRR
80
100
VIN=[VOUT(T)+1.0]V+1.0Vp-pAC
IOUT=50mA, f=10kHz
Current Limited
Short-circuit Current
CE ”High” Voltage
CE ”Low” Voltage
CE ”High” Current
CE ”Low” Current
(C series)
CE ”Low” Current
(D series)
30
50
E-1
E-2
IOUT=30mA
-40°C≤ Topr≤ 85°C
IOUT=10mA
300Hz ~ 50kHz
Ripple Rejection Rate
V
X0.98 VOUT(T) X1.02 X0.97 VOUT(T) X1.03
150
1mA ≤ IOUT ≤ 100mA
IOUT = 30mA
IOUT = 100mA
VIN= VOUT(T) +1.0V, VCE=VSS
VIN= VOUT(T) +1.0V, VCE=VSS
VIN=VCE=OUT(T)+1.0V
VOUT(T)+1.0V≤ VIN≤ 10V
IOUT=30mA
Circuit
1
dB
4
mA
mA
V
V
µA
1
1
1
1
2
-0.10
VIN
0.25
0.10
-0.15
VIN
0.20
0.15
-20
0.10
-25
0.15
µA
2
-0.10
0.10
-0.15
0.15
µA
2
Note
(NOTE 1) Unless otherwise stated, VIN =VOUT(T) +1.0V
(NOTE 2) VOUT(T)=Specified Output Voltage
(NOTE 3) VOUT(E)=Effective Output Voltage (I.e. the output voltage when “VOUT(T)+1.0V” is provided at the VIN pin while maintaining a certain
IOUT value)
(NOTE 4) Vdif= (VIN1 (NOTE6) – VOUT1 (NOTE5))
(NOTE 5) VOUT1=A voltage equal to 98% of the Output Voltage whenever an amply stabilized IOUT (VOUT(T)+1.0V) is input.
(NOTE 6) VIN1=The Input Voltage when VOUT1 appears as Input Voltage is gradually decreased.
(NOTE 7) The values for -40°C ≤ Topr ≤ 85°C are designed values.
P8/14
Rev. A, March 2006
ML6209
Dropout Voltage – Table 1
SYMBOL
E-0
PARAMETER
OUTPUT
Output Voltage (V)
VOLTAGE
E-1
E-2
Dropout Voltage 1 (mV)
Dropout Voltage 2 (mV)
(IOUT=30mA)
(IOUT=100mA)
Ta=25°C
85°C
Ta=25°C
-40°C ≤ Topr ≤ 85°C
Vdif1
Vdif1
Vdif1
Vdif1
Vdif2
Vdif2
Vdif2
Vdif2
MIN
MAX
TYP
MAX
TYP
MAX
TYP
MAX
TYP
MAX
1.50
1.455
1.545
400
500
410
520
600
800
620
820
1.55
1.504
1.597
400
500
410
520
600
800
620
820
1.60
1.552
1.648
300
380
310
400
500
680
520
700
1.65
1.601
1.700
300
380
310
400
500
680
520
700
1.70
1.649
1.751
250
320
260
330
400
620
420
640
1.75
1.698
1.803
250
320
260
330
400
620
420
640
1.80
1.746
1.854
200
250
210
260
350
480
360
500
1.85
1.795
1.906
200
250
210
260
350
480
360
500
1.90
1.843
1.957
140
180
150
190
320
460
340
480
1.95
1.892
2.009
140
180
150
190
320
460
340
480
2.00
1.960
2.040
100
150
110
160
270
420
290
440
2.05
2.009
2.091
100
150
110
160
270
420
290
440
2.10
2.058
2.142
100
150
110
160
250
400
280
410
2.15
2.107
2.193
100
150
110
160
250
400
280
410
2.20
2.156
2.244
100
150
110
160
250
400
280
410
2.25
2.205
2.295
100
150
110
160
250
400
280
410
2.30
2.254
2.346
100
150
110
160
240
380
280
400
2.35
2.303
2.397
100
150
110
160
240
380
280
400
2.40
2.352
2.448
100
150
110
160
240
380
280
400
2.45
2.401
2.499
100
150
110
160
240
380
280
400
2.50
2.450
2.550
90
120
100
130
230
350
260
380
2.55
2.499
2.601
90
120
100
130
230
350
260
380
2.60
2.548
2.652
90
120
100
130
230
350
260
380
2.65
2.597
2.703
90
120
100
130
230
350
260
380
2.70
2.646
2.754
90
120
100
130
230
350
260
380
2.75
2.695
2.805
90
120
100
130
230
350
260
380
2.80
2.744
2.856
90
120
100
130
220
330
260
370
2.85
2.793
2.907
90
120
100
130
220
330
260
370
2.90
2.842
2.958
90
120
100
130
220
330
260
370
2.95
2.891
3.009
90
120
100
130
220
330
260
370
3.00
2.940
3.060
80
100
90
110
220
300
260
350
3.05
2.989
3.111
80
100
90
110
220
300
260
350
3.10
3.038
3.162
80
100
90
110
200
280
240
330
3.15
3.087
3.213
80
100
90
110
200
280
240
330
3.20
3.136
3.264
80
100
90
110
200
280
240
330
VOUT(T)
VOUT
-40°C ≤ Topr ≤
P9/14
Rev. A, March 2006
ML6209
Dropout Voltage – Table 2
SYMBOL
E-0
PARAMETER
OUTPUT
Output Voltage (V)
VOLTAGE
E-1
E-2
Dropout Voltage 1 (mV)
Dropout Voltage 2 (mV)
(IOUT=30mA)
(IOUT=100mA)
Ta=25°C
85°C
Ta=25°C
-40°C ≤ Topr ≤ 85°C
Vdif1
Vdif1
Vdif1
Vdif1
Vdif2
Vdif2
Vdif2
Vdif2
MIN
MAX
TYP
MAX
TYP
MAX
TYP
MAX
TYP
MAX
3.25
3.185
3.315
80
100
90
110
200
280
240
330
3.30
3.234
3.366
80
100
90
110
200
280
240
330
3.35
3.283
3.417
80
100
90
110
200
280
240
330
3.40
3.332
3.468
80
100
90
110
200
280
240
330
3.45
3.381
3.519
80
100
90
110
200
280
240
330
3.50
3.430
3.570
80
100
90
110
200
280
240
330
3.55
3.479
3.621
80
100
90
110
200
280
240
330
3.60
3.528
3.672
80
100
90
110
200
280
240
330
3.65
3.577
3.723
80
100
90
110
200
280
240
330
3.70
3.626
3.774
80
100
90
110
200
280
240
330
3.75
3.675
3.825
80
100
90
110
200
280
240
330
3.80
3.724
3.876
80
100
90
110
200
280
240
330
3.85
3.773
3.927
80
100
90
110
200
280
240
330
3.90
3.822
3.978
80
100
90
110
200
280
240
330
3.95
3.871
4.029
80
100
90
110
200
280
240
330
4.00
3.920
4.080
70
90
80
100
180
260
220
310
4.05
3.969
4.131
70
90
80
100
180
260
220
310
4.10
4.018
4.182
70
90
80
100
180
260
220
310
4.15
4.067
4.233
70
90
80
100
180
260
220
310
4.20
4.116
4.284
70
90
80
100
180
260
220
310
4.25
4.165
4.335
70
90
80
100
180
260
220
310
4.30
4.214
4.386
70
90
80
100
180
260
220
310
4.35
4.263
4.437
70
90
80
100
180
260
220
310
4.40
4.312
4.488
70
90
80
100
180
260
220
310
4.45
4.361
4.539
70
90
80
100
180
260
220
310
4.50
4.410
4.590
70
90
80
100
180
260
220
310
4.55
4.459
4.641
70
90
80
100
180
260
220
310
4.60
4.508
4.692
70
90
80
100
180
260
220
310
4.65
4.557
4.743
70
90
80
100
180
260
220
310
VOUT(T)
VOUT
-40°C ≤ Topr ≤
P10/14
Rev. A, March 2006
ML6209
Dropout Voltage – Table 3
SYMBOL
E-0
PARAMETER
OUTPUT
Output Voltage (V)
VOLTAGE
E-1
E-2
Dropout Voltage 1 (mV)
Dropout Voltage 2 (mV)
(IOUT=30mA)
(IOUT=100mA)
Ta=25°C
85°C
Ta=25°C
-40°C ≤ Topr ≤ 85°C
Vdif1
Vdif1
Vdif1
Vdif1
Vdif2
Vdif2
Vdif2
Vdif2
MIN
MAX
TYP
MAX
TYP
MAX
TYP
MAX
TYP
MAX
4.70
4.606
4.794
70
90
80
100
180
260
220
310
4.75
4.655
4.845
70
90
80
100
180
260
220
310
4.80
4.704
4.896
70
90
80
100
180
260
220
310
VOUT(T)
VOUT
-40°C ≤ Topr ≤
4.85
4.753
4.947
70
90
80
100
180
260
220
310
4.90
4.802
4.998
70
90
80
100
180
260
220
310
4.95
4.851
5.049
70
90
80
100
180
260
220
310
5.00
4.900
5.100
50
80
60
90
160
240
200
290
5.05
4.949
5.151
50
80
60
90
160
240
200
290
5.10
4.998
5.202
50
80
60
90
160
240
200
290
5.15
5.047
5.253
50
80
60
90
160
240
200
290
5.20
5.096
5.304
50
80
60
90
160
240
200
290
5.25
5.145
5.355
50
80
60
90
160
240
200
290
5.30
5.194
5.406
50
80
60
90
160
240
200
290
5.35
5.243
5.457
50
80
60
90
160
240
200
290
5.40
5.292
5.508
50
80
60
90
160
240
200
290
5.45
5.341
5.559
50
80
60
90
160
240
200
290
5.50
5.390
5.610
50
80
60
90
160
240
200
290
5.55
5.439
5.661
50
80
60
90
160
240
200
290
5.60
5.488
5.712
50
80
60
90
160
240
200
290
5.65
5.537
5.763
50
80
60
90
160
240
200
290
5.70
5.586
5.814
50
80
60
90
160
240
200
290
5.75
5.635
5.865
50
80
60
90
160
240
200
290
5.80
5.684
5.916
50
80
60
90
160
240
200
290
5.85
5.733
5.967
50
80
60
90
160
240
200
290
5.90
5.782
6.018
50
80
60
90
160
240
200
290
5.95
5.831
6.069
50
80
60
90
160
240
200
290
6.00
5.880
6.120
50
80
60
90
160
240
200
290
P11/14
Rev. A, March 2006
ML6209
Typical Performance Characteristics
(1) Output Voltage VS Output Current
(2) Output Voltage VS Input Voltage
10 mA
30 mA
100 mA
P12/14
Rev. A, March 2006
ML6209
P13/14
Rev. A, March 2006
ML6209
(3) Supply Current VS Input Voltage
°
DISCLAIMER:
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and
reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use.
P14/14
Rev. A, March 2006