E_M-1W Series 1W, FIXED INPUT, ISOLATED & UNREGULATED DUAL OUTPUT SUPERMINIATURE SIP PACKAGE multi-country patent protection RoHS FEATURES ● High Efficiency up to 79% ● 6Pin SIP Package ● Small Footprint ● Industry Standard Pinout ● 3KVDC Isolation ● Temperature Range -40°C to +85°C ● No Heat sink Required ● No External Component Required ● RoHS Compliance PRODUCT PROGRAM Input Part Number Output Voltage (VDC) Nominal Range Max Min 3.3 3.0-3.6 ±5 ±100 ±10 70 ±5 ±100 ±10 72 E0305M-1W E0505M-1W ±9 ±56 ±6 77 E0512M-1W ±12 ±42 ±5 78 E0515M-1W ±15 ±33 ±4 79 E1205M-1W ±5 ±100 ±10 71 E1209M-1W ±9 ±56 ±6 73 E1212M-1W ±12 ±42 ±5 74 E1215M-1W ±15 ±33 ±4 75 E0509M-1W APPLICATIONS The E_M-1W Series are specially Efficiency (%, Typ) Current (mA) Voltage (VDC) 5 4.5-5.5 12 10.8-13.2 designed for applications where a group of polar power supplies are isolated from the input power supply in a distributed COMMON SPECIFICATIONS power supply system on a circuit board. Item These products apply to: Operating Temp. range -40 +85 1) Where the voltage of the input power Storage Temp. range -55 +125 supply is fixed (voltage variation ≤±10%); 2) Where isolation is necessary between Lead temperature Short circuit protection* ≤3000VDC); Temp. rise at full load voltage and the output ripple noise are not demanding. Such as: purely digital circuits, ordinary Min Typ Max Storage humidity range input and output (isolation voltage 3) Where the regulation of the output Test conditions 1.5mm from case for 10 seconds Units °C 95 % 300 °C 1 S 15 °C 25 Isolation voltage Tested for 1 minute and 1mA Max 3000 VDC Isolation resistance Test at 500VDC 1000 MΩ Cooling low frequency analog circuits, and IGBT Case material power device driving circuits. MTBF Free air convection Plastic (UL94-V0) 3500 K hours *Supply voltage must be discontinued at the end of short circuit duration. MODEL SELECTION OUTPUT SPECIFICATIONS E0505M-1W Item Ra te P ower P ack age S tyle O utpu t Vo lt age Input Vol tage Pr odu ct Se ries Min Typ Max Units 1 W 0.1 Line regulation For Vin change of 1% Load regulation 10% to 100% full load Output voltage accuracy MORNSUN Science& Technology co.,Ltd. Address: 2th floor 6th building, Hangzhou Industrial District, Guangzhou, China Tel: 86-20-38601850 Fax: 86-20-38601272 http://www.mornsun-power.com MORNSUN reserves the copyright Test conditions Output power ±1.2 % 15 % 10 See tolerance envelope graph Temperature drift 100% full load Output ripple& Noise* 20MHz Bandwidth 50 Switching frequency Full load, nominal input 100 0.03 %/°C 75 mVp-p KHz *Test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing of Power Converter section, application notes. Note: 1.All specifications measured at TA=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified. 2.See below recommended circuits for more details. Specifications subject to change without notice. E_M-1W A/0-2008 Page 1 of 2 Filtering In some circuits which are sensitive to noise TYPICAL CHARACTERISTICS and ripple, a filtering capacitor may be added to the DC/DC output end and input end to reduce the noise and ripple. However, the capacitance of the output filter capacitor must be proper. If the capacitance is too big, a startup problem might arise. For every channel of output, provided the safe and reliable operation is ensured, the greatest capacitance of its filter capacitor sees the external capacitor table. o Operating Temp.( C) EXTERNAL CAPACITOR TABLE Cin V in Vout Cout (VDC) (VDC) (uF) (uF) 5 4.7 5 4.7 12 24 -- OUTLINE DIMENSIONS& PIN CONNECTION 2.2 1 -- 9 12 15 2.2 1 0.47 It’s not recommended to connect any external capacitor First Angle Projection 2 4 5 6 (0.035) 1 in the application field with less than 0.5 watt output。 To get an extremely low ripple, an “LC” filtering RECOMMENDED FOOTPRINT network may be connected to the input and Top view, grid：2. 54mm(0.1inch) dia meter ：1.00mm(0.039inch) output ends of the DC/DC converter, which may produce a more significant filtering effect. It 1.9 (0.075) should also be noted that the inductance and the frequency of the “LC” filtering network should be 1 2 4 5 6 staggered with the DC/DC frequency to avoid mutual interference (Figure 1). 4.10 L L Vin DC DC C FOOT PRINT DETAILS Pin Functions (0.020) Note: Unit:mm(inch) Pin section:0.50*0.3mm(0.020*0.012inch) Pin tolerances: + 0.10mm（+0.004inch） Generaltolerances: +0.25mm( +0.010inch) +Vo C L GND 0V C -Vo (Figure 1) Vin 1 2 GND 4 5 6 +Vo Output Voltage Regulation and Over-voltage Protection Circuit The simplest device for output voltage regulation, over-voltage and over-current protection is a linear voltage regulator with overheat protection that is connected to the input or output end in series (Figure 2). APPLICATION NOTE Vin +Vout REG Requirement on output load 0V DC DC To ensure this module can operate efficiently and reliably, a minimum load is specified for GND -Vout this kind of DC/DC converter in addition to a maximum load (namely full load). During operation, make sure the specified range of input voltage is not exceeded, the minimum Vin output load is not less than 10% of the full load, and that this product should never be operated under no load! If the actual output power is very small, please connect a GND REG +Vout REG -Vout 0V DC DC resistor with proper resistance at the output end in parallel to increase the load, or use our (Figure2) company’s products with a lower rated output power. No parallel connection or plug and play. Overload Protection Under normal operating conditions, the output circuit of these products has no protection against over-current and short-circuits. The simplest method is to connect a self-recovery fuse in series at the input end or add a circuit breaker to the circuit. MORNSUN reserves the copyright Specifications subject to change without notice. E_M-1W A/0-2008 Page 2 of 2