Datasheet Copper OC-3 SFP Transceiver SFP-OC3-CX Features MSA compliance for SFP transceivers (SFF-8472) Detection for Loss-of-Signal (ITU-T G.783) Control for transmit power down* Handles over 12.7 dB of cable loss Extended temperature operation: -20 C to 85 C 75Ω media interface compliance for CMI coded 155 Mbps electrical interfaces - ITU-T G.703 - Telcordia GR-253 Overview 75Ω DIN 1.0/2.3 female coaxial interface for Type A and Type D coupling MRV’s SFP-OC3-CX module is a Small Form-factor Pluggable (SFP) module that offers easy full-duplex interfacing with 155 Mbps OC-3 electrical interfaces (STM-1e, ES1) over 75Ω telecommunications coaxial cable. It includes Clock and Data Recovery (CDR) in both directions, and a CMI encoder/decoder for transparent NRZ-to-CMI line code conversion. It provides Loss of Signal (LOS) detection for electrical CMI interfaces and the option to disable the transmit driver to support the Link Integrity Notification (LIN) feature on applicable MRV modules. A serial interface provides access to an on-board EEPROM for identification information including manufacturer, part number, serial number, and date code. Low power dissipation (0.6 W typical) The SFP-OC3-CS complies with Multi-Source Agreement SFF8472 for SFP transceivers. RoHS 5/6 compliance * LIN support for applicable MRV modules Benefits Provides end user flexibility through independent port configuration Reduces deployment cost for STM-1 electrical interfaces Figure 1: Transceiver Functional Diagram Circuit Pack Interface Applications Typical applications include SDH multiplexer systems or ATMswitch and IP-router equipment supporting SDH physical interfaces. The SFP-OC3-CX module is fully interchangeable with STM-1 and OC-3 optical SFP transceivers, offering system developers an easy migration to STM-1 electrical interfaces. Any system that already supports the STM-1 optical SFP also supports the STM-1 electrical SFP. This modular flexibility minimizes development efforts and time-to-market for STM-1 solutions because a single card design supports both optical and electrical STM-1 interfaces. The SFP-OC3-CX and optical STM-1 SFP interfaces can be changed in the field to match the system port types to the application while the system is in operation. The common SFP interface also allows for reduced inventory of field replacements. 1 DATA OUT 155 Mbps STM-1e Line Interface TXDIS Line Coding Clock Recovery TX RXLOS Monitor & Control DATA IN 155 Mbps CLOCK EEPROM DATA EEPROM Line Coding Clock Recovery RX EEPROM Serial ID STM-1e CMI-OUT 155 Mbps STM-1e CMI-IN 155 Mbps Datasheet Serial ID Interface The SFP-OC3-CX supports the 2-wire serial EEPROM protocol for the ATMEL AT24C02, as defined by the MSA for access to identification information. The memory is organized as byte-wide data that can be addressed individually or sequentially at device address 1010000X (A0h). Receiver Specifications Cable Flat-Loss Tolerance 0 to 12.7 dB Latency 5 to 10 UI DLL Lock Time 1 to 10 μs Return Loss 7MHz to 240MHz 15 dB min Input Signal Must comply with ITU-T G.703 Transmitter Specifications Bit Rate 155.52 Mbps ± 20 ppm Line Code Coded Mark Inversion (CMI) Relevant Specification ITU-T G.703, ANSI T1.102, Telcordia GR-253-CORE With the coaxial output port driving a 75Ω load, the output pulses conform to the templates in ITU-T G.703 and G.783. Transmitter Specifications Peak-to-peak Output Voltage Template Steady state 0.9 to 1.1 V Rise/ Fall Time 10-90% 2 ns Transition Timing Tolerance Transitions at mid-interval -0.35 to +0.35 Ns Return Loss 7MHz to 240MHz 15 dB min Environmental and Regulatory Compliance ESD threshold 1KV at faceplate* Radiated Emission FCC Part 15 Class B EN55022, CISPR 22 (6db margin) Radiated Immunity Class A per IEC-801-3, EN55082-1, IEC-61000-4-3, GR-1089 Component Recognition CSA C22.2, UL 60950-1 Shock and Vibration 0.2 G p-p, 9 – 62 Hz Flammability 94V0 * Varies with system design. 2 Datasheet Model Description Protocol Connectors Impedance Maximum Cable Length Operating Temperature Range Ordering Information SFP-OC3-CX Copper SFP Transceiver OC-3 Coax 1.0/2.3 BNC 75 Ohms 100 Meters -20 to 85 ºC ACCESSORIES Ordering Information: ACCESSORIES Model Description 1600125-001R Coax cables, 2 used with SFP For more information about MRV’s SFP transceivers, visit www.mrv.com or contact [email protected]. MRV has more than 50 offices throughout the world. Addresses, phone numbers and fax numbers are listed at www.mrv.com. Please e-mail us at [email protected] or call us for assistance. MRV Los Angeles 20415 Nordhoff St. Chatsworth, CA 91311 800-338-5316 818-773-0900 MRV Boston 295 Foster St. Littleton, MA 01460 800-338-5316 978-952-4700 MRV International Business Park Moerfelden Waldeckerstrasse 13 64546 Moerfelden-Walldorf Germany Tel. (49) 6105/2070 Fax (49) 6105/207-100 All statements, technical information and recommendations related to the products herein are based upon information believed to be reliable or accurate. However, the accuracy or completeness thereof is not guaranteed, and no responsibility is assumed for any inaccuracies. Please contact MRV Communications for more information. MRV Communications and the MRV Communications logo are trademarks of MRV Communications, Inc. Other trademarks are the property of their respective holders. MRV-OP-SFOOC3CX-111308 3020056-001 Rev. A1 Copyright ©2008 MRV Communications, Inc. All Rights Reserved.