QUS40-096 Isolated Bus Converter INPUT CHARACTERISTICS Conditions1 Parameter Input voltage operating range Min. Typ. Max. 38 48 55 Input voltage absolute maximum Input undervoltage lockout Input overvoltage lockout Maximum input current No-load input current Disabled input current FEATURES RoHS compliant 48 VIN, Isolated, 5:1 fixed conversion ratio 385W power at 48VIN 300W output at 38 VIN, 55ºC, 200 LFM Industry standard ¼ brick footprint Remote enable (primary side, positive or negative) Over-temperature, over current protections Direct parallel operation for higher power DESCRIPTION The QUS40-096 is a RoHS compliant fixed 5:1 ratio bus converter in an industry standard quarter brick footprint to support Intermediate Bus Architecture (IBA) for powering multiple downstream non-isolated point-of-load (POL) converters. The output is unregulated and the 5:1 fixed ratio is maintained between the input and output voltages. It features input voltage range of 38V to 55V, and provides up to 384W @ 48Vin of power or 300W at 38Vin @ 55ºC, typical efficiency of 9.6V module is 96.6%. It can be parallel for more power. Input reflected ripple current Enable - negative logic version Internal 27.4KΩ pulled-up to internal 5.0V Resistance from enable pin to -VIN Units 60 Turn-on threshold Turn-off threshold Hysteresis voltage Turn-on threshold Turn-off threshold Hysteresis voltage Steady-state (40 AOUT) Enabled state, no load (48VIN) Disabled state (48VIN) 34 32 55 57 35.5 33.5 2 58.5 2 8.4 100 7 Measured into the input pin Input capacitor 47μF type Nichicon UPM1J470MPH or equivalant 36 34 VDC 58 59.5 9 ADC mA mA 300 mA rms On state range -0.1 0.8 VDC Off state range 2.4 15.0 VDC With +VIN pin open, or tired to -VIN 16.12 KΩ OUTPUT CHARACTERISTICS Parameter Conditions1 Min. Typ. Max. Units Output voltage set point Output load regulation VIN = 48V, IO = 0A IO = 0 to 40A VIN = 38 to 55V, PO = 0 to 300W, Ta = 55ºC 20MHz bandwidth Corresponding to PO = 300W VIN = 48V, PO = 300W 9.40 9.50 0.35 9.60 VDC V 11.0 VDC 150 42 mV p-p A % Output voltage total regulation 2 Output ripple & noise Output current operating range Efficiency 7.0 80 0 96.6 Turn-on delay From enable, <0.8V to VO> 10% for VIN = 38V - 55V 0.5 10 ms Output voltage rise time3 Start-up inhibit time Transient response3 From 10% to 90% Enabled: VIN applied to 90% VOUT 25% step, 1A/μs, Co=1200μF 12 140 220 15 350 ms ms %VO Current sharing accuracy (up to 3 in parallel) At PO = 300W 5 10 % 0 0 350 350 3750 mV mV μF Output turn on overshoot Output turn off undershoot Maximum output capacitance 1 VIN = 48Vdc, Ta = 25ºC, Airflow = 200LFM for all data unless otherwise noted. 2 Output Ripple Voltage and noise is specified when measured with a 10μF tantalum and a 1uF ceramic capacitor at the output pins. 3 During output voltage rise time (15ms Max.), output power shall be limited to 50% constant power. Transient response is specified with a 960μF capacitor at the output of the converter. For full details go to www.murata-ps.com/rohs www.murata-ps.com Technical enquiries email: [email protected], tel: +1 508 339 3000 QUS40-096.B01 Page 1 of 3 QUS40-096 Isolated Bus Converter PROTECTION CHARACTERISTICS Parameter Output over-current shutdown 2 Over temperature shutdown3 Over temperature restart hysteresis Conditions1 Min. Typ. Max. Units Auto-restart Restart rate Auto-restart 44 48 80 135 10 50 A ms ºC ºC 140 GENERAL CHARACTERISTICS Parameter Conditions Min. Isolation voltage Isolation resistance Storage temperature range Operating temperature range Operating humidity Thermal measurement location temperature3 Material flammability Input to output Input to output Non-condensing 2250 10 -40 -40 10 MTBF Non-condensing See mechanical drawing for location UL 94V-0 Calculated per Mil Spec 217 E, or Bellcore at Ta=30ºC Demonstrated 2 1.3 Typ. Max. Units 125 85 90 130 VDC MΩ ºC ºC % ºC x106 Hrs x106 Hrs 3.3 STANDARDS COMPLIANCE Standards UL/CSA 60950 Conditions4 Basic insulation MANUFACTURING TESTING Burn-in test Parametric test SAFETY CONSIDERATIONS The QUS series of converters are certified to the standards and extent listed in the ‘Standards Compliance’ section in the table above. If this product is built into information technology equipment, the installation must comply with the above standard. Even though the product is safety certified to operate without an input fuse, it is recommended that an input fuse of 15A (max.) is used. The output of the converter (Vo+/Vo-) is considered to remain within SELV limits when the input to the converter meets SELV or TNV-2 requirements. The converters and materials meet UL 94V-0 flammability ratings. RoHS COMPLIANCE The QUS40-096 converter is in compliance with the European Union Directive 2002/95/EC (RoHS) with respect to the following substances: lead (Pb), cadmium (Cd), mercury (Hg), hexavalent chromium, polybrominated biphenyls (PBB) and polybrominated diphenyl ethers (PBDE). For further information, please visit www.cd4power.com/rohs 1 2 3 4 VIN = 48Vdc, Ta = 25ºC, Airflow = 200LFM for all data unless otherwise noted. Input transient: if input voltage increases by 5V in 1μs, output over-current shut-down shall not be triggered (tested with Max. load and Max. output capacitance). Thermal shutdown is monitored at the Thermal Measurement Location (TML). See ‘Mechanical Information’ on page 3 for TML location. See ‘Safety Considerations’ shown above. Derating curves are conducted in a controlled environment. End application testing is required to ensure the Thermal Measurement Location temperature is below the maximum specified. Recommended airflow direction is from pin 1 to pin 3, or 3 to 1 (transversal to the unit). www.murata-ps.com Technical enquiries email: [email protected], tel: +1 508 339 3000 QUS40-096.B01 Page 2 of 3 QUS40-096 Isolated Bus Converter PACKAGE SPECIFICATIONS MECHANICAL DIMENSIONS 0.480 (12.19) Max. Ø0.040 ± 0.002 (1.02 ± 0.06) (3X) y Ø0.062 ± 0.002 (1.57 ± 0.06) (2X) TML PIN #3 PIN #4 0.300 (7.62) PIN #2 0.600 (15.24) 0.600 (15.24) 1.45 (36.8) Recommended Footprint PIN #5 PIN #1 0.43 (10.8) 0.14 (3.6) 2.000 (50.80) Ø0.060 (1.52) 2.28 (57.9) Bottom view Ø0.093 (2.36) Ø0.105 (2.67) Ø0.137 (3.48) Dimensions: 2.3 (58.4) L x 1.45 (36.83) W x 0.48 (12.19) H Max. All dimensions in inches (mm). Tolerance: X.X (X.XX) ±0.5 (0.2), X.XX (X.XXX) ±0.25 (0.010). Max. 0.480 (12.19) between highest component and mounting plane. PIN CONNECTIONS ORDERING INFORMATION Pin Assignment 1 2* 3 4 5 +VIN ON/OFF -VIN -VOUT +VOUT QUS x x - y y y - N H z R v C O u tp ut C urren t O u tp ut vo lta g e 40 = 40A 096 = 9.6V Factory Internal Control Revision (Not required when ordering) E n a b le lo g ic N = N e gative lo g ic P = P os itive log ic * Referenced to -VIN C = R oH S C om p lia n t H orizo n ta l M o u n t USA: P in L e n g th B = 0 .1 4 5 '' Reserved C = 0.2 0 0 '' Mansfield (MA), Tel: (508) 339-3000, email: [email protected] Canada: Toronto, Tel: (866) 740-1232, email: [email protected] Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. Tel: (508) 339-3000 (800) 233-2765 Fax: (508) 339-6356 UK: Milton Keynes, Tel: +44 (0)1908 615232, email: [email protected] France: Montigny Le Bretonneux, Tel: +33 (0)1 34 60 01 01, email: [email protected] Germany: München, Tel: +49 (0)89-544334-0, email: [email protected] www.murata-ps.com email: [email protected] ISO 9001 REGISTERED Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2008 Murata Power Solutions, Inc. Japan: Tokyo, Tel: 3-3779-1031, email: [email protected] Osaka, Tel: 6-6354-2025, email: [email protected] Website: www.murata-ps.jp China: Shanghai, Tel: +86 215 027 3678, email: [email protected] Guangzhou, Tel: +86 208 221 8066, email: [email protected] 04/22/2008 www.murata-ps.com Technical enquiries email: [email protected], tel: +1 508 339 3000 QUS40-096.B01 Page 3 of 3