28 Pin SMD 5 Tap TTL Compatible Active Delay Lines ELECTRONICS INC. EP9100 to EP9129 & EP9100-RC to EP9129-RC Add “-RC” after part number for RoHS Compliant J-Lead Part Number EP9100(-RC) EP9101(-RC) EP9102(-RC) EP9103(-RC) EP9104(-RC) EP9105(-RC) EP9106(-RC) EP9107(-RC) Gull-Wing Part Number EP9115(-RC) EP9116(-RC) EP9117(-RC) EP9118(-RC) EP9119(-RC) EP9120(-RC) EP9121(-RC) EP9122(-RC) Tap Delays (†±5% or ± 2nS) 5 6 7 8 9 10 12 15 10 12 14 16 18 20 24 30 15 18 21 24 27 30 36 45 Total Delay (†±5% or ± 2nS) 20 24 28 32 36 40 48 60 J-Lead Part Number EP9108(-RC) EP9109(-RC) EP9110(-RC) EP9111(-RC) EP9112(-RC) EP9113(-RC) EP9114(-RC) 25 30 35 40 45 50 60 7 Gull-Wing Part Number EP9123(-RC) EP9124(-RC) EP9125(-RC) EP9126(-RC) EP9127(-RC) EP9128(-RC) EP9129(-RC) Tap Delays (†±5% or ± 2nS) 20 40 60 80 25 50 75 100 30 60 90 120 35 70 105 140 40 80 120 160 45 90 135 180 50 100 150 200 Total Delay (†±5% or ± 2nS) 100 125 150 175 200 225 250 †Whichever is greater. • Delay times referenced from input to leading edges at 25°C, 5.0V, with no load. 4 VCC 2 4 Schematic DC Electrical Characteristics Parameter 26 PCA EP9100(-RC) D.C. Test Conditions Min. High-Level Output Voltage Low-Level Output Voltage Input Clamp Voltage High-Level Input Current VCC = min. VIL = max. I OH = max VCC = min. VIH = min. IOL= max VCC = min. II = IIK VCC = max. VIN = 2.7V VCC = max. VIN = 5.25V IIL Low-Level Input Current VCC = max. VIN = 0.5V IOS Short Circuit Output Current VCC = max. VOUT = 0. (One output at a time) ICCH High-Level Supply Current VCC = max. VIN = OPEN ICCL Low-Level Supply Current VCC = max. VIN = 0 TRO Output Rise Time Td ≤ 500 nS (0.75 to 2.4 Volts) Td > 500 nS NH Fanout High-Level Output VCC = max. VOH = 2.7V NL Fanout Low-Level Output VCC = max. VOL = 0.5V Recommended Operating Conditions VCC Supply Voltage VIH High-Level Input Voltage VIL Low-Level Input Voltage IIK Input Clamp Current IOH High-Level Output Current IOL Low-Level Output Current PW* Pulse Width of Total Delay d* Duty Cycle TA Operating Free-Air Temperature Min. 4.75 2.0 Max. 5.25 0.8 -18 -1.0 20 40 0 40 +70 Max. Unit 0.5 -1.2 50 1.0 -2 -100 V V V µA mA mA mA 2.7 -40 Pulse Input Voltage Pulse Width % of Total Delay Pulse Rise Time (0.75 - 2.4 Volts) Pulse Repetition Rate @ Td ≤ 200 nS Pulse Repetition Rate @ Td > 200 nS VCC Supply Voltage Suggested Solder .365 Pad Layout .475 (9.27) (12.07) .370 Max. (9.40) 18 .175 Max. (4.45) .050 Typ. (1.27) .025/.045 (.635/1.14) 4 1 28 26 PCA EP9129(-RC) D.C. 12 .370 Max. (9.40) .365 (9.27) Suggested Solder Pad Layout .475 (12.07) 18 .050 Typ. (1.27) .030 (.762) .450 Max. (11.43) .175 Max. (4.45) .050 Typ. (1.27) Notes : 1. Assembly Process Volts % nS MHz KHz Volts .018 x .008 (.457 x .203) Tin Plated Kova .055 (1.40) Gull Wing Package (Leadframe) (Assembly Solder) .050 Typ. (1.27) .018 x .008 (.457 x .203) Tin Plated Kovar EP91XX SnPb EP91XX-RC Sn SnPb SnPb (RoHS exemption 7a) Unit 3.2 110 2.0 1.0 100 5.0 .050 Typ. (1.27) .030 (.762) .450 Max. (11.43) 75 mA 75 mA 4 nS 5 nS 20 TTL Load 10 TTL Load (Solder Composition) Input Pulse Test Conditions @ 25° C 12 Unit V V V mA mA mA % % °C *These two values are inter-dependent. EIN PW TRI PRR 1 28 INPUT 12 18 GROUND VOH VOL VIK IIH .055 (1.40) J-Lead Package 15 28 17 26 OUTPUT 2. Peak Solder Rating 225°C 260°C 3 (168 hours, ≤30°C/60%RH) 4 (72 hours, ≤30°C/60%RH) (per IPC/JEDEC J-STD-020C) 3. Moisture Sensitive Levels (MSL) (per IPC/JEDEC J-STD-020C) 4. Weight 5. Packaging Information (Tube) TBD grams TBD grams 45 pieces/tube 45 pieces/tube Unless Otherwise Specified Dimensions are in Inches /mm ± .010 /.25 PCA ELECTRONICS, INC. 16799 SCHOENBORN ST. NORTH HILLS, CA 91343 Product performance is limited to specified parameters. Data is subject to change without prior notice. CS9810-XX & -RC Rev. A1 1/31/06 RR TEL: (818) 892-0761 FAX: (818) 894-5791 http://www.pca.com