PI3L301D 3.3V, 16-Bit to 8-Bit, Mux/DeMux Gigabit Ethernet LAN Switch with Single Enable Features Description • • • • • • • • • • • Pericom Semiconductor’s PI3L series of logic circuits are produced using the Company’s advanced sub-micron CMOS technology, achieving industry leading performance. RON is 4Ω typical Low bit-to-bit skew: 200ps Low crosstalk: –27dB @ 250MHz Low Current Consumption: 20µA Near-Zero propagation delay: 250ps Switching speed: 9ns Channel On-Capacitance: 9.5pF (typical) VCC Operating Range: +3.0V to +3.6V ESD >2000V . . . Human Body Model >350 MHz bandwidth (or data frequency) Packaging (Pb-free & Green available): 48-pin 240 mil wide plastic TSSOP (A) 48-pin 173 mil wide plastic TVSOP (K) The PI3L301D is a 16- to 8-bit multiplexer/demultiplexer LAN Switch. Industry leading advantages include a propagation delay of less than 250ps, resulting from its low channel resistance and I/O capacitance. The device multiplexes differential outputs from a Gigabit Ethernet transceiver (PHY) device to one of two corresponding B1 or B2 outputs. The switch is bidirectional and offers little or no attenuation of the high-speed signals at the outputs. It is designed for low bit-to-bit skew, high channel-to-channel noise isolation and is compatible with various standards, such as 10/100/ 1000 Base-T (Ethernet). Generally, this part can be used to replace mechanical relays in low-voltage LAN applications that interface a physical layer over CAT 5 or CAT 6 unshielded twisted pair cable through an isolation transformer. Applications • Dual Physical Layer Device sharing to one interface connector • SONET OC-12(622Mbps) signal routing • Routes physical layer signals for 10/100/1000 Mbit Ethernet Pin Description Block Diagram A0 0B1 A1 1B1 0B2 1B2 A2 2B1 A3 3B1 2B2 3B2 A4 4B1 A5 5B1 4B2 5B2 V DD 1 48 0B1 1B1 A0 2 47 GND 3 46 GND A1 4 45 0B2 GND 5 44 1B2 V DD 6 43 GND GND 7 42 2B1 A2 8 41 3B1 GND 9 40 GND A3 10 11 39 38 2B2 GND V DD 12 37 GND GND 13 36 V DD NC 14 35 4B1 A4 15 34 5B1 GND 16 33 GND A5 17 32 4B2 3B2 A6 GND 18 31 6B1 V DD 5B2 19 30 A7 GND 7B1 GND 20 29 A6 6B1 21 28 GND 7B1 22 27 A7 GND 23 24 26 6B2 6B2 7B2 SEL SEL 1 25 7B2 PS8665B 07/22/03 PI3L301D 3.3V, 16-Bit to 8-Bit, Mux/DeMux Gigabit Ethernet LAN Switch with Single Enable Maximum Ratings Truth Table (Above which useful life may be impaired. For user guidelines, not tested.) Storage Temperature....................................–65°C to +150°C Supply Voltage to Ground Potential...............–0.5V to +4.0V DC Input Voltage............................................–0.5V to +5.5V DC Output Current......................................................120mA Power Dissipation...........................................................0.5W Function SEL AN to NB1 L AN to NB2 H Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2 PS8665B 07/22/03 PI3L301D 3.3V, 16-Bit to 8-Bit, Mux/DeMux Gigabit Ethernet LAN Switch with Single Enable DC Electrical Characteristics for 1000 Base-T Ethernet Switching over Operating Range (TA = –40°C to +85°C, VCC = 3.3V ±10%) Paramenter Description Test Conditions Min. Typ.(2) Max. Units VIH Input HIGH Voltage Guaranteed HIGH level 2 - - VIL Input LOW Voltage Guaranteed LOW level –0.5 - 0.8 VIK Clamp Diode Voltage VCC = Max., IIN = –18mA - –0.7 –1.2 IIH Input HIGH Current VCC = Max., VIN = VCC - - ±5 IIL Input LOW Current VCC = Max., VIN = GND - - ±5 IOFF Power Down Leakage Current VCC = 0V, VA = 0V, VB ≤ 3.6 - - ±5 RON Switch On-Resistance(3) VCC = Min., 1.5V ≤ VIN ≤ VCC, IIN = –40mA - 4 8 RFLAT(ON) On-Resistance Flatness(4) VCC = Min., VIN @ 1.5V and VCC, IIN = –40mA - 1 - ∆RON On-Resistance match from center ports to any other port(4) VCC = Min., 1.5V ≤ VIN ≤ VCC, IIN = –40mA - 0.9 2 V µA Ω DC Electrical Characteristics for 10/100 Base-T Ethernet Switching over Operating Range (TA = –40°C to +85°C, VCC = 3.3V ±10%) Paramenter Description Test Conditions Min. Typ.(2) Max. Units VIH Input HIGH Voltage Guaranteed HIGH level 2.0 - - VIL Input LOW Voltage Guaranteed LOW level –0.5 - 0.8 VIK Clamp Diode Voltage VCC = Max., IIN = –18mA - –0.7 –1.2 IIH Input HIGH Current VCC = Max., VIN = VCC - - ±5 IIL Input LOW Current VCC = Max., VIN = GND - - ±5 IOFF Power Down Leakage Current VCC = 0V, VA = 0V, VB ≤ 3.6 - - ±5 RON Switch On-Resistance(3) VCC = Min., 1.25V ≤ VIN ≤ VCC, IIN = –10mA to –30mA - - 8 RFLAT(ON) On-Resistance Flatness(4) VCC = Min., VIN @ 1.25V and VCC, IIN = –10mA to –30mA - 1.0 - ∆RON On-Resistance match from center ports VCC = Min., 1.25V ≤ VIN ≤ VCC, to any other port(4) IIN = –10mA to –30mA - 0.9 2.0 3 PS8665B V µA Ω 07/22/03 PI3L301D 3.3V, 16-Bit to 8-Bit, Mux/DeMux Gigabit Ethernet LAN Switch with Single Enable Capacitance (TA = 25°C, f = 1MHz) Parameters(4) Description Test Conditions CIN Input Capacitance COFF(B1, B2) Port B Capacitance, Switch OFF CON(A/B) A/B Capacitance, Switch ON Typ. Max. 3.1 3.6 2.8 6.0 9.5(5) 10.9 VIN = 0V Units pF Notes: 1. For max. or min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 3.3V, TA = 25°C ambient and maximum loading. 3. Measured by the voltage drop between A and B pins at indicated current through the switch. On-Resistance is determined by the lower of the voltages on the two (A & B) pins. 4. This parameter is determined by device characterization but is not production tested. 5. Measured on worst case corner pin. Power Supply Characteristics Parameters ICC Test Conditions(1) Description Quiescent Power Supply Current VCC = Max., VIN = GND or VCC Min. Typ.(2) Max. Units - - 800 µA Notes: 1. For max. or min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 3.3V, TA = 25°C ambient and maximum loading. Dynamic Electrical Characteristics Over the Operating Range (TA=-40º to +85ºC, VCC=3.3V±10%, GND=0V) Parameter Description Test Conditions Min. Typ.(2) Max. XTALK Crosstalk f = 250MHz, See Fig. 2 - -27 - OIRR OFF Isolation f = 250MHz, See Fig. 3 - -32 - BW Bandwidth –3dB CL = 10pf, See Fig. 1 - 350 - Units dB MHz Switching Characteristics Paramenter Test Min. Conditions Description tPD Propagation Delay(2,3) tPZH, tPZL tPHZ, tPLZ (2) Typ. Max. - 0.25 Line Enable Time - SEL to AN, BN 0.5 - 15 Line Disable Time - SEL to AN, BN 0.5 - 9 tSK(o) Output Skew between center port (A4 to A5) to any other port(2) - 0.1 0.2 tSK(p) Skew between opposite transitions of the same output (tPHL - tPLH) (2) - 0.1 0.2 Units ns Notes: 1. For max. or min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Guaranteed by design. 3. The bus switch contributes no propagational delay other than the RC delay of the On-Resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.25ns for 10pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in a system is determined by the driving circuit on the driving side of the switch and its interactions with the load on the driven side. 4 PS8665B 07/22/03 PI3L301D 3.3V, 16-Bit to 8-Bit, Mux/DeMux Gigabit Ethernet LAN Switch with Single Enable Test Circuit for Electrical Characteristics(1) 6.0V VCC 200-ohm Pulse Generator VIN VOUT D.U.T 10pF CL RT 200-ohm Notes: 1. CL = Load capacitance: includes jig and probe capacitance. 2. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator 3. All input impulses are supplied by generators having the following characteristics: f = 10MHz, ZO = 50Ω, tR ≤ 2.5ns, tF ≤ 2.5ns. 4. The outputs are measured one at a time with one transition per measurement. Switch Positions Test Switch tPLZ, tPZL (output on B-side) 6.0V tPHZ, tPZH (output on B-side) GND Prop Delay Open HP4396B R S T HP11667A VCC PI3L301D 50-ohm 50-ohm 50-ohm CL = 10pF Figure 1. Bandwidth -3db Testing 5 PS8665B 07/22/03 PI3L301D 3.3V, 16-Bit to 8-Bit, Mux/DeMux Gigabit Ethernet LAN Switch with Single Enable HP4396B R S T HP11667A PI3L301D 50-ohm 100 -ohm 50-ohm 50-ohm 100 -ohm Figure 2. Crosstalk Test Setup HP4396B R S T HP11667A 50-ohm PI3L301D 50-ohm 50-ohm 100 -ohm Figure 3 . Off Isolation Tets Setup 6 PS8665B 07/22/03 PI3L301D 3.3V, 16-Bit to 8-Bit, Mux/DeMux Gigabit Ethernet LAN Switch with Single Enable Switching Waveforms 2.5V SEL 1.25V 1.25V 0V Input A 3.5V 2.5V Input tPHL 1.5V VDD VOL +0.3V tPHZ tPZH VOH –0.3V VDD/2 VOH 2.5V tPLZ VDD/2 2.5V tPLH Output tPZL Output A 2.5V Voltage Waveforms Propagation Delay Times VOH VDD/2 Output B VOL VOL tPHZ tPZH VOL VOL VDD/2 VOL Voltage Waveforms Enable and Disable Times 3.5V Data In at Ax or Ay 2.5V tPLHX 1.5V tPHLX 3.5V VOH 2.5V Data Out at MBx I tSK(o) tPLH VOL 1.5V 2.5V Output 2.5V VOL VOL tPLHy tPHL VOH VOH Data Out at MBy 2.5V Input tSK(p) = I tPHL – tPLH I tPHLy tSK(o) = I tPLHy – tPLHx I or I tPHLy – tPHLx I Output Skew - tSK(o) Pulse Skew - tSK(p) Applications Information Logic Inputs The logic control inputs can be driven up to +3.6V regardless of the supply voltage. For example, given a +3.3V supply, the output enables or select pins may be driven low to 0V and high to 3.6V. Driving IN Rail-to-Rail® minimizes power consumption. Power-Supply Sequencing Proper power-supply sequencing is advised for all CMOS devices. It is recommended to always apply VCC before applying signals to the input/output or control pins. Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd 7 PS8665B 07/22/03 PI3L301D 3.3V, 16-Bit to 8-Bit, Mux/DeMux Gigabit Ethernet LAN Switch with Single Enable Packaging Mechanical: 48-Pin TSSOP (A) 48 .236 .244 1 6.0 6.2 .488 12.4 .496 12.6 .047 1.20 Max SEATING PLANE .004 0.09 .008 0.20 X.XX X.XX .0197 BSC 0.50 DENOTES DIMENSIONS IN MILLIMETERS 0.45 .018 0.75 .030 .002 .006 0.05 0.15 .007 .010 0.17 0.27 .319 BSC 8.1 Packaging Mechanical: 48-Pin TVSOP (K) 48 .169 .177 4.30 4.50 .0035 .008 .031 .041 0.80 1.05 1 .378 9.60 .386 9.80 0.09 0.20 0.45 .018 0.75 .030 .252 BSC 6.4 SEATING PLANE X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS .016 BSC 0.40 .002 .006 0.05 0.15 .0051 .009 0.13 0.23 8 Max. .047 1.20 PS8665B 07/22/03 PI3L301D 3.3V, 16-Bit to 8-Bit, Mux/DeMux Gigabit Ethernet LAN Switch with Single Enable Ordering Information Ordering Code Package Code Package Description PI3L301DA A 48-pin 240 mil wide plastic TSSOP PI3L301DAE A Pb-free & Green, 48-pin 240 mil wide plastic TSSOP PI3L301DK K 48-pin 173 mil wide plastic TVSOP PI3L301DKE K Pb-free & Green, 48-pin 173 mil wide plastic TVSOP Notes: 1. Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ Pericom Semiconductor Corporation • 1-800-435-2336 • www.pericom.com 9 PS8665B 07/22/03