AND180HRP Ultra Bright LED Lamps: Type 3 Weight: 0.31 g Unit: mm AND180HRP 5.6±0.2 5.6±0.2 InGaAlP High Brightness Red Light Emission T-1 3/4 Package (5 mm) 5.0±0.2 5.0±0.2 Features 1.0 1.0 MIN. MIN. 26.4 26.4 MIN. MIN. 1.0±0.2 1.0±0.2 8.6±0.3 8.6±0.3 • Peak wavelength (lp = 644 nm) high bright emission • All plastic mold type, clear colorless lens • Low drive current: 1 to 20 mA DC • Excellent On-Off contrast ratio • Fast response time, capable of pulse operation • High power luminous intensity • Suitable for Outdoor Message Signboards • RoHS Compliant 0.5 0.5 Maximum Ratings (Ta = 25°C) 2.54 2.54 1 2 1 2 0.5 0.5 Cathode Index Cathode Index 1. Anode 1. 2. Anode Cathode 2. Cathode Characteristics Symbol Rating Unit Forward Current IF 50 mA Reverse Voltage VR 4 V Power Dissipation PD 125 mW Operating Temperature Range TOpr -40 to 85 °C Storage Temperature Range TStg -40 to 100 °C Electro-Optical Characteristics (Ta = 25°C) Characteristics Symbol Test Condition Minimum Typical Maximum Forward Voltage VF IF = 20 mA Unit – 1.9 2.5 V Reverse Current IR VR = 4 V – – 50 µA Luminous Intensity IV IF = 20 mA 3,200 6,000 – mcd Peak Emission Wavelength lP IF = 20 mA – 644 – nm Spectral Line Half Width ∆l IF = 20 mA – 18 – nm Dominant Wavelength ld IF = 20 mA – 630 – nm Full Viewing Angle q IV = 1/2 Peak – 8 – degree Precaution Please be careful of the following: 1. Soldering temperature: 260°C max Soldering time: 5 sec. max Soldering portion of lead: up to 1.6 mm from the body of the device 2. The lead can be formed up to 5 mm from the body of the device without forming stress. Soldering should be performed after the lead forming. Product specifications contained herein may be changed without prior notice. It is therefore advisable to contact Purdy Electronics before proceeding with the design of equipment incorporating this product. Purdy Electronics Corporation • 720 Palomar Avenue • Sunnyvale, CA 94085 Tel: 408.523.8200 • Fax: 408.733.1287 • [email protected] • www.purdyelectronics.com 6/14/07 AND180HRP InGaAlP High Brightness Red Light Emission Ultra Bright LED Lamps: Type 3 IV – IF IF – VF 50000 50 Ta = 25°C Luminous Intensity IV (mcd) Forward Current IF (mA) 30000 Ta = 25°C 30 10 5 3 1 1.6 1.7 1.8 1.9 2.0 2.1 2.2 10000 5000 3000 1000 500 0.5 2.3 1 Forward Voltage VF (V) IV – TC 5 10 30 50 100 Relative Luminous Intensity – Wavelength 3 1.0 Relative Luminous Intensity Relative Luminous Intensity 3 Forward Current IF (mA) 1 0.5 0.3 0.1 -20 0 20 40 60 IF = 20 mA Ta = 25°C 0.8 0.6 0.4 0.2 0 580 80 600 620 640 660 680 700 Wavelength λ (nm) Case Temperature TC (°C) Radiation Pattern IF – Ta 20° 10° 0° 10° Ta = 25°C 20° 30° 30° 40° 40° 50° 50° 60° 60° 70° 70° 80° 80° Allowable Forward Current IF (mA) 80 60 40 20 90° 90° 0 0.2 0.4 0.6 0.8 0 0 20 40 60 80 Ambient Temperature Ta (°C) Purdy Electronics Corporation • 720 Palomar Avenue • Sunnyvale, CA 94085 Tel: 408.523.8200 • Fax: 408.733.1287 • [email protected] • www.purdyelectronics.com 100 6/14/07