AND4GRA Ultra Bright LED Lamps: Type 2 Weight: 2.0 mg Unit: mm AND4GRA InGaN Ultra Bright Green Light Emission Surface Mount Package Features • Small package size • 2.0 (l) x 1.25 (w) x 1.1 (h) size • Suitable for DIP and REFLOW soldering • Recommended Forward Current: 10 mA • RoHS Compliant Maximum Ratings (Ta = 25°C) Product specifications contained herein may be changed without prior notice. It is therefore advisable to contact Purdy Electronics before proceeding with the design of equipment incorporating this product. Characteristics Symbol Rating Unit Forward Current IF 30 mA Reverse Voltage VR 5 V Power Dissipation PD 120 mW Operating Temp. Range TOpr -30 to 80 °C Storage Temp. Range TStg -40to 100 °C Electro-Optical Characteristics (Ta = 25°C) Characteristics Symbol Test Condition Minimum Typical Maximum Unit Forward Voltage VF IF = 20 mA 3.1 3.5 3.8 V Reverse Current IR VR = 5 V – – 100 µA Luminous Intensity IV IF = 20 mA 84 140 – mcd Peak Emission Wavelength lP IF = 20 mA – 540 – nm Spectral Line Half Width ∆l IF = 20 mA – 45 – nm Dominant Wavelength ld IF = 20 mA – 530 – nm 2 q 1/2 IF = 20 mA – 120 – degree Full Viewing Angle Precaution Please be careful of the following: 1. Manual soldering: maximum temperature of iron tip: 260°C max. Soldering time: within 5 sec. per solder-land Soldering portion of lead: up to 1.6 mm from the body of the device 2. Reflow solder: recommended condition is as follows: Temperature 10 sec. max. 140 - 160°C 3. Absolute secure counter measures against static electricity and surge should be taken when handling these products. It is recommended to use wrist band or antistatic gloves when handling these LEDs. The following soldering patterns are recommended for reflow soldering: 230°C max. more than 2 min. 4°C/sec. max. Time Purdy Electronics Corporation • 720 Palomar Avenue • Sunnyvale, CA 94085 Tel: 408.523.8200 • Fax: 408.733.1287 • [email protected] www.purdyelectronics.com 7/18/07 AND4GRA InGaN Ultra Bright Green Light Emission Ultra Bright LED Lamps: Type 2 IV – IF IF – VF 1000 Ta = 25°C Ta = 25°C Luminous Intensity IV (mcd) Forward Current IF (mA) 100 50 10 5 3 1 2.0 100 10 2.5 3.0 3.5 4.0 4.5 5.0 1 5.5 3 Forward Voltage VF (V) IV – TC 10 5 30 50 Forward Current IF (mA) 100 Relative Luminous Intensity – Wavelength Relative Luminous Intensity Relative Luminous Intensity 1.0 100 10 -20 0 20 40 60 IF = 20 mA Ta = 25°C 0.8 0.6 0.4 0.2 0 400 80 450 500 550 600 650 700 Wavelength λ (nm) Case Temperature TC (°C) Radiation Pattern IF – Ta 20° 10° 0° 10° Ta = 25°C 20° 30° 30° 40° 40° 50° 50° 60° 60° 70° 70° 80° 80° Allowable Forward Current IF (mA) 40 30 20 10 90° 90° 0 0.2 0.4 0.6 0.8 0 0 20 40 60 80 Ambient Temperature Ta (°C) Purdy Electronics Corporation • 720 Palomar Avenue • Sunnyvale, CA 94085 Tel: 408.523.8200 • Fax: 408.733.1287 • [email protected] www.purdyelectronics.com 100 7/18/07