Displays ANDpSi025TD-LED-KIT 2.5” Active Color TFT LCD Color Monitor The ANDpSi025TD-LED-KIT is an 640 x 240 active matrix color TFT LCD Module with Digital and Analog Interface that utilizes new low temperature poly-silicon (p-Si) technology to provide brighter, thinner and lighter display with high resolution. Both of horizontal and vertical scan are reversible and controlled by the serial interface commands. The product is designed for the requirement of the green product, and the specification complies with Toppoly’s “Green Product Chemical Substance Specification Standard Hand Book”. All these features making it ideal for portable applications including personal digital assistants (PDAs), medical instruments and test & measurements instruments. Features • • • • • • • • Absolute Maximum Ratings (Cont.) (GND=0V) p-Si construction with drivers on glass High luminance Digital and Analog Interface NTSC and PAL format compatible 16 Million/Full Color Slim (2.53 mm) and lightweight design Transmissive type. FIxed current LED backlight RoHS Compliant Specification Unit 2.0 inch Transmissive – Display Size (diag.) Min. Max. Unit Operating Temp. Topr -10 +60 ºC Storage Temp. Tstg -30 +80 ºC Electrical Characteristics (GND=0V, Ta = 25°C) Driving TFT LCD Panel Mechanical Characteristics Item Symbol Item Item Symbol Min. Typ. Power Supply for H/V Driver VCC 2.85 3.0 3.6 Input Driver Voltage Max. Unit Low VIL GND – 0.2 x VCC* VIH 0.8 x VCC* – VCC* VPWM 0 – VCC* V 40.672 (H) x 30.48 (V) mm VD, HD, DCLK, DIN[0:7], SDA, SCL, SCEN, SHDB, High GRESTB 640 (H) x RGB x 240 (V) dot PWM Output Voltage 0.0635 (H) x 0.127 (V) mm Feedback Voltage VFB 0.55 0.6 0.65 V RGB Delta – Panel Power Consumption Wp – 50 60 mW Color Numbers 16 Million/Full Color – Outline Dimensions 46.1(H) x 40.96(V) x 2.53* (D) mm 8.5 g VCC*=VCC(TYP) The VCC power is provided for overall panel Note 1: module supply voltage. Note 2: DC/DC feedback control voltage. Hard Coating (3H) – Display Type Active Area Number of Dots Dot Pitch Color Arrangement Weight Panel surface treatment Item Absolute Maximum Ratings (GND=0V) Symbol Symbol Min. Typ. Max. Unit Forward Current IF – 23 25 mA Min. Max. Unit Forward Current Volt. VF – 3.4 3.6 V Backlight Power Consumption* WBL – 78.2 90 mW Logic Power Supply Voltage VCC -0.5 4.5 V Input Signal Voltage VD, HD, DCLK, DIN[0:7], SDA, SCL, SCEN, SHDB, GRESTB VIN1 0 VCC V Backlight Forward current IF – 25 mA 4/16/09 V Driving Backlight in Standard Mode (Ta = 25°C) * Exclude FPC and protrusions. Item V * Backlight driving circuit is recommended as the fix current circuit Purdy Electronics Corporation • 720 Palomar Avenue • Sunnyvale, CA 94085 Tel: 408.523.8200 • Fax: 408.733.1287 • [email protected] www.purdyelectronics.com 1 Displays ANDpSi025TD-LED-KIT Dimensional Outline Unit: mm Standard Tolerance: 0.5mm 2 Purdy Electronics Corporation • 720 Palomar Avenue • Sunnyvale, CA 94085 Tel: 408.523.8200 • Fax: 408.733.1287 • [email protected] www.purdyelectronics.com 4/16/09 Displays ANDpSi025TD-LED-KIT Timing Chart YUV Mode: ITUR601-NTSC Symbol Item Dot Clock Frequency Min. Typ. Max. Unit DCLK – 27 – MHz Display Area – 1440 – DCLK th – 1716 – DCLK thpw 1 1 – DCLK Horizontal Back Porch thb – 240 – DCLK Horizontal Front Porch thfp – 36 – DCLK Horizontal Dummy Time thdm – 4 – DCLK Horizontal Display Active Horizontal Line HSYNC PUlse Width Serial RGB Dummy Mode and Serial YUV 4:2:2 Mode: Horizontal YUV Mode: ITUR601-PAL Item Symbol Min. Typ. Max. Unit DCLK – 27 – MHz Display Area – 1440 – DCLK th – 1728 – DCLK HSYNC PUlse Width thpw 1 1 – DCLK Horizontal Back Porch thb – 240 – DCLK Horizontal Front Porch thfp – 48 – DCLK Horizontal Dummy Time thdm – 4 – DCLK Dot Clock Frequency Horizontal Display Active Horizontal Line 4/16/09 Purdy Electronics Corporation • 720 Palomar Avenue • Sunnyvale, CA 94085 Tel: 408.523.8200 • Fax: 408.733.1287 • [email protected] www.purdyelectronics.com 3 Displays ANDpSi025TD-LED-KIT Timing Chart With Analog Interface Symbol Min Typ Max – 25 – – 24.54 – – 24.38 – Display Area – 1280 – DCLK th – 1560 – DCLK HSYNC PUlse Width thpw – 1 – DCLK Horizontal Back Porch thb – 240 – DCLK Horizontal Front Porch thfp – 40 – DCLK Horizontal Dummy Time thdm – 4 – DCLK Item QVGA Dot Clock Frequency NTSC DCLK PAL Horizontal Display Active Horizontal Line Optical Specification Symbol Viewing Angle Chromaticity 4 Condition Min. Typ. Max. θ11 30 40 – θ12 30 40 – 15 20 – θ22 40 50 – θ21 Contrast Ratio Luminance MHz Ta=25ºC Item Response Time Unit CR ≥ 10 CR 200 300 – Rising Tr – 13 20 Falling Tf – 22 30 IF=23mA L 200 250 – xw 0.26 0.31 0.36 yw 0.29 0.34 0.39 White θ = 0º Unit degree – ms cd/m2 – Purdy Electronics Corporation • 720 Palomar Avenue • Sunnyvale, CA 94085 Tel: 408.523.8200 • Fax: 408.733.1287 • [email protected] www.purdyelectronics.com 4/16/09 Displays ANDpSi025TD-LED-KIT Input/Output Terminals TFT LCD Panel - Recommended connector Molex 51374-4073 Pin Symbol Input/Output 1 CP3 C 2 CP4 C Capacitor for power setting 3 CP5 C Capacitor for charge pump 4 CP6 C Capacitor for charge pump 5 CP7 C Capacitor for charge pump 6 CP8 C Capacitor for charge pump 7 DUMMY – Dummy 8 DUMMY – Dummy 9 PCD C Capacitor for pre-charge data signal high 10 VCOML C Capacitor for VCOM low Capacitor for VCOM high Description Capacitor for power setting 11 VCOMH C 12 AGND – Analog ground 13 DUMMY – Dummy 14 AVDD C Regulation capacitor for analog voltage 15 CP1 C Capacitor for charge pump 16 CP2 C Capacitor for charge pump 17 PWM O Power transistor gate signal for the boost converter 18 FB I Main boost regulator feedback input 19 LED- – LED power: cathode; Note 1 below 20 DUMMY – Dummy 21 DUMMY – Dummy 22 LED+ – LED power: anode; Note 1 below 23 GND – Ground 24 VCC – Power supply for digital circuit and charge pump circuit 25 VSYNC I Vertical sync input. Negative polarity 26 HSYNC I Horizontal syn input. Negative polarity 27 DCLK I Clock signal, latch data onto line latches at the rising edge 28 DIN0 I Data input 29 DIN1 I Data input 30 DIN2 I Data input 31 DIN3 I Data input 32 DIN4 I Data input 33 DIN5 I Data input 34 DIN6 I Data input 35 DIN7 I Data input 36 SDA I/O Serial interface data line 37 SCL I Serial interface clock line 38 SCEN I Serial interface chip enable line 39 SHDB I Shutdown input 40 GREST I System reset pin Note 1: The figure to the left shows the connection of backlight LED. 4/16/09 Purdy Electronics Corporation • 720 Palomar Avenue • Sunnyvale, CA 94085 Tel: 408.523.8200 • Fax: 408.733.1287 • [email protected] www.purdyelectronics.com 5 Displays ANDpSi025TD-LED-KIT PC-TFT-25TD Interface Board Features • Used for TFT-LCD display: 2.5” ANDpSi025TD-LED Environment: Working Temp.: -20~60ºC Relative Humidity: 5~95% RH Storage Temp: -25ºC ~ +70ºC Relative Humidity: 0~90% RH • Both PAL + NTSC • 1 x CVBS input signal (1.0Vp-p) • OSD Menu • IR remote control (optional). OSD Function Description: Menu (PICTURE) Item Brightness Contrast Color Sharpness Hue The PC-TFT-25TD is designed to work with the ANDpSi025TD-LED color TFT display which is suitable for automotive, small size home use TV, video broadcasting & test equipment. Description Value Adjust brightness 0-100 Adjust contrast 0-100 Adjust color 0-100 Adjust sharpness 0-100 Adjust HUE (only work on NTSC) 0-100 Keys function: 6 Button Function Y2 Power switch MENU OSD menu On/Off ENTER Select the item iniside the OSD menu UP Increase the current item’s value DOWN Decrease the current item’s value Purdy Electronics Corporation • 720 Palomar Avenue • Sunnyvale, CA 94085 Tel: 408.523.8200 • Fax: 408.733.1287 • [email protected] www.purdyelectronics.com 4/16/09 Displays ANDpSi025TD-LED-KIT Connector Connector CN2 CON5 Input/Output CVBS signal input DC voltage input Remark Suggest to use 12V DC only Panel 4/16/09 Pin Symbol I/O Description 1 CP3 C Capacitor for charge pump 2 CP4 C Capacitor for charge pump 3 CP5 C Capacitor for charge pump 4 CP6 C Capacitor for charge pump 5 CP7 C Capacitor for charge pump 6 CP8 C Capacitor for charge pump 7 NC – No connection 8 PCDL C Capacitor for pre-charge data signal low 9 PCDH C Capacitor for -repcharge data signal high 10 VCOML C Capacitor for VCOM low 11 VCOMH C Capacitor for CVOM high 12 AGND – Analog ground 13 PVDD C Regulation capacitor for charge pump 14 AVDD C Regulation capacitor for analog voltage 15 CP1 C Capacitor for charge pump 16 CP2 C Capacitor for charge pump 17 PWM O Power transistor gate signal for the boost converter 18 FB I Main boost regulator feedback input 19 LED- – LED power: cathode 20 LED+ – LED power: anode 21 NC – No connection 22 GND – Ground 23 VCC – Power supply 24 VD I Vertical sync input 25 HD I Horizontal sync input 26 DCLK I Clock signal, latch data onto line latches at the rising edge 27 DIN0 I Data input 28 DIN1 I Data input 29 DIN2 I Data input 30 DIN3 I Data input 31 DIN4 I Data input 32 DIN5 I Data input 33 DIN6 I Data input 34 DIN7 I Data input 35 SDA I/O Serial interface data line 36 SCL I Serial interface clock line 37 SCEN I Serial interface chip enable line 38 SHDB I Sleep mode setting pin 39 GRESTB I Global reset pin Purdy Electronics Corporation • 720 Palomar Avenue • Sunnyvale, CA 94085 Tel: 408.523.8200 • Fax: 408.733.1287 • [email protected] www.purdyelectronics.com 7 Displays ANDpSi025TD-LED-KIT ID Input/Output Remarks CN6 CVBS signal & Power Input Suggest to use stabilized 12 V DC JP1 OSD control connector CN1 TFT panel input connector Molex 51374-4073 Electrical Parameters Value Item Min. Working voltage Working current 8 Typ. Max. Unit 6 12 15 V with panel 110 110 110 mA without panel 60 60 60 mA Purdy Electronics Corporation • 720 Palomar Avenue • Sunnyvale, CA 94085 Tel: 408.523.8200 • Fax: 408.733.1287 • [email protected] www.purdyelectronics.com 4/16/09