05H1L RECTRON THRU SEMICONDUCTOR TECHNICAL SPECIFICATION 05H6L SURFACE MOUNT HIGH EFFICIENCY RECTIFIER VOLTAGE RANGE 50 to 600 Volts CURRENT 0.5 Ampere FEATURES * * * * * * * Low power loss, high efficiency Low leakage Low forward voltage High current capability High speed switching High surge capability High reliability SOD-123FL .114 (2.9) .106 (2.7) MECHANICAL DATA * Epoxy: Device has UL flammability classification 94V-O * Mounting position: Any * Weight: 0.016 gram .035 (0.90) .028 (0.70) .077 (1.95) .069 (1.75) .008 MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS (0.20) .039 (1.00) .035 (0.90) .030 (0.75) .022 (0.55) Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. .150 (3.8) For capacitive load, derate current by 20%. .142 (3.6) Dimensions in inches and (millimeters) MAXIMUM RATINGS (At T A = 25oC unless otherwise noted) SYMBOL 05H1L 05H2L 05H3L 05H4L 05H5L 05H6L UNITS Maximum Recurrent Peak Reverse Voltage RATINGS VRRM 50 200 300 400 600 Volts Maximum RMS Voltage Maximum DC Blocking Voltage VRMS 35 50 100 70 100 140 200 210 300 280 400 420 600 Volts Maximum Average Forward Rectified Current at T A= 55 oC Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range VDC IO I FSM CJ Amps 15 Amps 15 12 -55 to + 150 T J , T STG Volts 0.5 pF 0 C ELECTRICAL CHARACTERISTICS (At TA = 25oC unless otherwise noted) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 0.5A DC Maximum DC Reverse Current at Rated DC Blocking Voltage T A = 25o C Maximum Full Load Reverse Current Average, Full Cycle .375” (9.5mm) lead length at T L = 55oC Maximum Reverse Recovery Time (Note 1) NOTES : 1. Test Conditions: IF = 0.5A, IR = -1.0A, IRR = -0.25A 2. Measured at 1 MHZ and applied reverse voltage of 4.0 volts 3. “Fully ROHS compliant”, “100% Sn plating (Pb-free)”. SYMBOL VF 05H1L 05H2L 1.0 05H3L 05H4L 05H5L 1.3 05H6L UNITS 1.7 Volts 5.0 uAmps IR 100 trr 50 uAmps 75 nSec 2006-3 REV:O RATING AND CHARACTERISTIC CURVES ( 05H1L THRU 05H6L ) FIG. 2 - TYPICAL FORWARD CURRENT DERATING CURVE trr +0.5A (-) 0 -0.25A (NOTE 2) (+) -1.0A 1cm NOTES:1 Rise Time = 7ns max. Input Impedance = SET TIME BASE FOR 10/20 ns/cm 1 megohm. 22pF. 2. Rise Time = 10ns max. Source Impedance = 50 ohms. TJ = 25 .1 .01 V 00 .1 60 1.0 1.0 0/2 TJ = 100 10 /10 TJ = 150 10 TJ = 25 .01 Pulse Width = 300uS 1% Duty Cycle .001 0 20 40 60 80 100 120 140 0 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) 18 JUNCTION CAPACITANCE, (pF) 21 8.3ms Single Half Sine-Wave (JEDEC Method) 15 12 9 6 3 0 1 2 5 10 20 50 NUMBER OF CYCLES AT 60Hz 100 .2 .4 .6 .8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, (V) FIG. 6 - TYPICAL JUNCTION CAPACITANCE FIG. 5 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, (A) 0 25 50 75 100 125 150 175 AMBIENT TEMPERATURE ( ) 50 100 0 FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANTANEOUS FORWARD CURRENT, (A) INSTANTANEOUS REVERSE CURRENT, (uA) FIG. 3 - TYPICAL REVERSE CHARACTERISTICS 0.5 V OSCILLOSCOPE (NOTE 1) 00 1 NONINDUCTIVE Single Phase Half Wave 60Hz Resistive or Inductive Load 0/4 PULSE GENERATOR 0V D.U.T (+) 25 Vdc (approx) (-) 1.0 30 10 NONINDUCTIVE AVERAGE FORWARD CURENT, (A) FIG. 1 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50 NONINDUCTIVE 200 100 60 40 20 05H 1L~ 10 05H 5L TJ = 25 6 4 05H 6L 2 1 .1 .2 .4 1.0 2 4 10 20 40 100 REVERSE VOLTAGE, ( V ) RECTRON Mounting Pad Layout 0.014 MIN. (0.36 MIN.) 0.029 MIN. (0.73 MIN.) 0.150 (3.80) REF Dimensions in inches and (millimeters) RECTRON