RL101FG RECTRON THRU SEMICONDUCTOR TECHNICAL SPECIFICATION FAST RECOVERY GLASS PASSIVATED RECTIFIER RL107FG VOLTAGE RANGE 50 to 1000 Volts CURRENT 1.0 Ampere FEATURES * * * * * * High reliability Low leakage Low forward voltage drop High current capability Glass passivated junction High switching capability A-405 MECHANICAL DATA * * * * * Case: Molded plastic Epoxy: Device has UL flammability classification 94V-O Lead: MIL-STD-202E method 208C guaranteed Mounting position: Any Weight: 0.33 gram 1.0 (25.4) MIN. .205 (5.2) .166 (4.2) .025 (0.6) DIA. .021 (0.5) .107 (2.7) .080 (2.0) DIA. 1.0 (25.4) MIN. MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) MAXIMUM RATINGS (At T A = 25 oC unless otherwise noted) RATINGS SYMBOL R L 1 0 1 F G RL102FG R L 1 0 3 F G R L 1 0 4 F G R L 1 0 5 F G R L 1 0 6 F G R L 1 0 7 F G UNITS Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS Voltage VRMS 35 50 70 100 140 200 280 400 420 600 560 800 700 1000 Volts Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375” (9.5mm) lead length at TA = 50oC Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range VDC Volts IO 1.0 Amps I FSM 30 Amps CJ 15 T J , T STG -65 to + 175 SYMBOL VF RL101FG RL102FG RL103FG RL104FG RL105FG RL106FG RL107FG pF 0 C ELECTRICAL CHARACTERISTICS (At TA = 25oC unless otherwise noted) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 1.0A DC Maximum DC Reverse Current at Rated DC Blocking Voltage TA = 25 oC Maximum Full Load Reverse Current Full Cycle Average, .375” (9.5mm) lead length at T L = 55 oC Maximum Reverse Recovery Time (Note 1) NOTES : 1. Test Conditions: IF = 0.5A, IR = -1.0A, IRR = -0.25A 2. Measured at 1 MHZ and applied reverse voltage of 4.0 volts 1.3 UNITS Volts 5.0 uAmps IR 100 trr 150 uAmps 250 500 nSec 2001-5 RATING AND CHARACTERISTIC CURVES ( RL101FG THRU RL107FG ) FIG. 2 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 50 1.0 PEAK FORWARD SURGE CURRENT, (A) AVERAGE FORWARD CURRENT, (A) FIG. 1 - TYPICAL FORWARD CURRENT DERATING CURVE .8 .6 .4 Single Phase Half Wave 60Hz Resistive or Inductive Load .2 8.3ms Single Half Sine-Wave (JEDED Method) 40 30 20 10 0 0 0 1 25 50 75 100 125 150 175 AMBIENT TEMPERATURE, ( ) 2 4 6 8 10 20 40 60 80 100 NUMBER OF CYCLES AT 60Hz FIG. 3 - TYPICAL INSTANTANEOUS FIG. 4 - TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, (uA) INSTANTANEOUS FORWARD CURRENT, (A) FORWARD CHARACTERISTICS 20 10 3.0 1.0 TJ = 25 Pulse Width=300uS 1% Duty Cycle 0.3 0.1 .03 .01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 JUNCTION CAPACITANCE, (pF) 50 NONINDUCTIVE (+) 25 Vdc (approx) (-) TJ = 25 6 4 TJ = 25 .06 .04 .02 .01 20 40 10 NONINDUCTIVE 60 80 100 120 140 trr +0.5A (-) D.U.T 0 PULSE GENERATOR -0.25A (NOTE 2) 1 NONINDUCTIVE OSCILLOSCOPE (NOTE 1) (+) -1.0A NOTES:1 Rise Time = 7ns max. Input Impedance = 1 megohm. 22pF. 2. Rise Time = 10ns max. Souce Impedance = 50 ohms. 2 1 .1 .2 .1 FIG. 6 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 200 10 .6 .4 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) FIG. 5 - TYPICAL JUNCTION CAPACITANCE 20 2 1.0 0 1.8 INSTANTANEOUS FORWARD VOLTAGE, (V) 100 60 40 10 6 4 .2 .4 1cm SET TIME BASE FOR 50/100 ns/cm 1.0 2 4 10 20 40 100 REVERSE VOLTAGE, ( V ) RECTRON