规格书编号 SPEC NO : 产品规格书 SPECIFICATION CUSTOMER 客 户: PRODUCT 产 品: SAW FILTER MODEL NO 型 号: HD F4552 PREPARED 编 制: CHECKED 审 核: Houshihong APPROVED 批 准: CHARLES D A T E 日 期: 2007-01-25 客户确认 CUSTOMER RECEIVED: 审核 CHECKED 批准 APPROVED 日期 DATE 无锡市好达电子有限公司 Shoulder Electronics Limited www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 1 of 13 HD F4552 SAW FILTER 更改历史记录 History Record 更改日期 Date www.shoulder.cn 规格书编号 Spec No 产品型号 Part No 客户产品型号 Customer No Tel:0755-82916880 Fax:0755-82916881 更改内容描述 Modify Content E-mail:[email protected] 备注 Remark Page 2 of 13 HD F4552 SAW FILTER 1.Features _ RF bandpass filter for CDMA450 Tx. Part _ Usable bandwidth 5MHz (452.5MHz ~ 457.5 MHz) _ High attenuation _ No matching 50Ω single-ended operation _ Ceramic Surface Mounted Device Package ( 3.8 mm *3.8 mm ) 2. Maximum Ratings Parameter Operating Temperature Range Storage Temperature Range DC Voltage VDC Power Handling Capability Rating -30~85 -40~85 10 27 Unit °C °C V dBm 2-1-1Electrical characteristics( T=25°C) Minimum Center Frequency ( F0 ) MHz Insertion Loss (F0 +/- 2.5 MHz) Amplitude Ripple (F0 +/- 2.5 MHz) dB dB VSWR (F0 +/- 2.5 MHz) Relative Attenuation 0.3 MHz ~ 350.0 MHz 350.0 MHz ~ 441.0 MHz 462.5 MHz ~ 467.5 MHz 467.5 MHz ~ 1200 MHz Input/Output Impedance www.shoulder.cn Tel:0755-82916880 - Typical 455.0 Maximum - - 2.0 2.8 - 0.8 1.2 - 1.4 2.0 - dB Ω Fax:0755-82916881 25 25 40 25 - E-mail:[email protected] 30 30 30 50 - Page 3 of 13 HD F4552 SAW FILTER 2-1-2.Electrical characteristics( T=+70°C~-20°C) Minimum Center Frequency ( F0 ) MHz Insertion Loss (F0 +/- 2.5 MHz) Amplitude Ripple (F0 +/- 2.5 MHz) dB dB VSWR (F0 +/- 2.5 MHz) Relative Attenuation 0.3 MHz ~ 350.0 MHz 350.0 MHz ~ 441.0 MHz 462.5 MHz ~ 467.5 MHz 467.5 MHz ~ 1200 MHz dB Input/Output Impedance Ω - Typical 455.0 Maximum - - 2.0 3.5 - 0.8 1.2 - 1.4 2.0 - 25 25 30 25 30 30 30 - 50 - 2-2.Typical frequency response www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 4 of 13 HD F4552 SAW FILTER 2-3 Input / Output VSWR Charts www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 5 of 13 HD F4552 SAW FILTER 2-4 Input / Output Smith Charts www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 6 of 13 HD F4552 SAW FILTER 3. TEST CIRCUIT 4-1. DIMENSION www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 7 of 13 HD F4552 SAW FILTER 4-2Marking Configuration 1) Pad Number 1 Index 2) Manufacturer name 3) Marking Number 4) Lot Number 4-3 picture 5.Environmental Performance Characteristics Item High temperature Low temperature Humidity www.shoulder.cn Condition The specimen shall be store at a temperature of 85±2℃ for 96±4h. Then it shall be subjected to standard atmospheric conditions for 1h, after which measurement shall be made within 1h. The specimen shall be store at a temperature of -30±3℃ for 96±4h. Then it shall be subjected to standard atmospheric conditions for 1h, after which measurement shall be made within 1h. The specimen shall be store at a temperature of Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Specifications Mechanical characteristics and specifications in electrical characteristics shall Page 8 of 13 HD F4552 SAW FILTER Thermal shock Resistance to Soldering heat Solder ability www.shoulder.cn 40±2℃ with relative humidity of 90% to 96% for 96±4h. Then it shall be subjected to standard atmospheric conditions for 1h, after which measurement shall be made within 1h. The specimen shall be subjected to 8 continuous cycles each as shown below. Then it shall be subjected to standard atmospheric conditions for 1h, after which measurement shall be made within 1h. Temperature Duration 1 +25℃=>-40℃ 0.5h 2 -40℃ 4h 3 -40℃=>+85℃ 2h 4 +85℃ 4h 5 +85℃=>+25℃ 0.5h 6 +25℃ 1h Reflow soldering method Peak: 255 ±5 ℃, 220 ±5℃, 40s At electrode temperature of the specimen. be satisfied. There shall be no excessive change in appearance. The specimen shall be passed through the reflow furnace with the condition shown in the above profile for 1 time. The specimen shall be stored at standard atmospheric conditions for 1h, after which the measurement shall be made. Test board shall be 1.6 mm thick. Base material shall be glass fabric base epoxy resin. Immerse the pins melt solder at 260℃+5/-0℃ More then 95% of for 5 sec. total area of the pins should be covered with solder Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 9 of 13 HD F4552 SAW FILTER 6.Mechanical Test Items Vibration Drop Lead pull Lead bend Conditions 600-3300rpm amplitude 1.5mm 3 directions 2 H each On maple plate from 1m high 3 times Pull with 1kg force for 30 seconds 90o bending with 500g weigh 2 times Specifications There shall be no damage. 7. REMARK 7.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 7.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 7.3 Soldering Only leads of component may be soldered. Please avoid soldering another part of component. 8. Packing 8.1 Dimensions (1) Carrier Tape: Figure 1 (2) Reel: Figure 2 (3) The product shall be packed properly not to be damaged during transportation and storage. 8.2 Reeling Quantity 1000 pcs/reel 7’’ 3000 pcs/reel 13’’ 8.3 Taping Structure (1) The tape shall be wound around the reel in the direction shown below. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 10 of 13 HD F4552 SAW FILTER (2) Label Device Name User Product Name Quantity Lot No. (3) Leader part and vacant position specifications. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 11 of 13 HD F4552 SAW FILTER 9. TAPE SPECIFICATIONS 9.1 Tensile Strength of Carrier Tape: 4.4N/mm width 9.2 Top Cover Tape Adhesion (See the below figure) (1) pull off angle: 0~15º (2) speed: 300mm/min. (3) force: 20~70g [Figure 1] Carrier Tape Dimensions [Unit:mm] W F E P0 P1 P2 D0 D1 t1 t2 A B 12.00 ±0.30 5.50 ±0.10 1.75 ±0.10 4.00 ±0.10 8.00 ±0.10 2.00 ±0.10 Ø1.50 Ø1.0 ±0.25 0.25 ±0.05 1.65 ±0.10 4.04 ±0.10 4.10 ±0.10 www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 12 of 13 HD F4552 SAW FILTER [Figure 2] [Unit:mm] A B C D E W t r Ø330 ±1.0 Ø100 ±0.5 Ø13 ±0.5 Ø21 ±0.8 2 ±0.5 13 ±0.3 3 max. 1.0 max. 10.REVIRION Date 2005-6-15 2006-5-16 2006-5-25 2006-7-7 2008-1-30 www.shoulder.cn Page Tel:0755-82916880 Revision A B C D E Fax:0755-82916881 Reason NEW Customer’s require Customer’s require Customer’s require Customer’s require E-mail:[email protected] Page 13 of 13