SA1469TN 4-CH BTL DRIVER FOR CD PLAYER WITH 3.3V OUTPUT VOLTAGE DESCRIPTION The SA1469TN, an IC for CD players, has a 4-channel BTL driver, 3.3V regulator (attached PNP transistor required), standard operational amplifier, and internal reset output linked to an internal thermal shutdown circuit. The driver has gain adjustment input pins for each channel, allowing gain to be set to the desired value. Also, the internal level shift circuit helps reduce the number of attached components. FEATURES HSOP - 28-375-0.8 * 1-phase, full-wave, linear DC motor driver. * Gain is adjustable with an attached resistor. * Internal standard operational amplifier. * Internal 3.3V regulator. (required attached PNP transistor) * Internal thermal shutdown circuit with hysteresis capabilities. * When voltage of PIN23<0.7V(typ.),the driver will be muted. ORDERING INFORMATION Device Package SA1469TN HSOP-28-375-0.8 BLOCK DIAGRAM HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http://www.silan.com.cn REV:1.2 2008.07.23 Page 1 of 11 SA1469TN ABSOLUTE MAXIMUM RATING (Tamb=25°C, unless otherwise specified) Characteristic Symbol Value Unit Supply Voltage VCC 18 V Power Dissipation PD 1.7(Note) W Operating Temperature Topr -40~+85 °C Storage Temperature Tstg -55~+150 °C Maximum Output Current Imax 1 A Note: 1. When mounted on 76mm x 114mm x 1.57mm PCB (Phenolic resin material). 2. Power dissipation reduces 13.6mW / °C for using above Tamb=25 °C. 3. Do not exceed Pd and SOA (Safe Operating Area). 2.0 1.5 1.0 0.5 0 0 25 50 75 100 125 150 175 Ambient temperature: ( Tamb ℃) ELECTRICAL CHARACTERISTICS (Tamb=25°C, VCC=8.0V, unless otherwise specified) Parameter Symbol Test conditions Min. Typ. Max. Unit A REGULATOR PART Regulator Output Voltage VREG IL=100mA 3.13 3.3 3.47 V Load Regulation ΔVRL IL=0mA to 200mA -40.0 0 10.0 mV Line Regulation ΔVCC IL=200mA, VCC=6 to 9V -10.0 0 20.0 mV Quiescent Circuit Current ICCQ VI=0 5.5 9.5 13.5 mA Input Offset Voltage VOF - -5.0 0 5.0 mV Output Offset Voltage VOO - -30 0 30 mV Maximum Sink Current ISINK RL=4Ω, VCC 0.5 0.8 -- A Maximum Source Current ISOU RL=4Ω, GND 0.5 0.8 -- A VI=2VRMS, 1KHz, RL=8Ω 4.3 4.5 4.6 V VI=2VRMS, 1KHz, RL=∞ 5.4 5.6 5.8 V B DRIVER PART Maximum Output Voltage (P4/P9/P20/P24 input) VOM Closed Loop Voltage Gain A/F VI=0.1VRMS, 1kHz 7.0 8.0 9.0 dB Ripple Rejection Ratio RR VI=-20dB, 120Hz 60.0 80.0 -- dB Slew Rate SR 100Hz, squarewave 1.0 2.0 -- V/μs HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http://www.silan.com.cn REV:1.2 2008.07.23 Page 2 of 11 SA1469TN Parameter Symbol Test conditions Min. Typ. Max. Unit C OP AMP Input Offset Voltage VOF1 - -5.0 0 5.0 mV IB1 - -- -- 300 nA Input Bias Current High Level Output Voltage VOH1 - 6 - - V Low Level Output Voltage VOL1 - - - 1.8 V Output Sink Current ISINK1 RL=50Ω, GND 10 40 - mA ISOURCE1 RL=50Ω, VCC 10 50 - mA GVO1 VIN=-75dB, f=1KHz 65 78 - dB Ripple Rejection Ratio RR1 VIN=-20dB, 120Hz 50 70 - dB Slew Rate SR Square, VOUT=2Vp-p, f=120KHz 0.5 1 - V/μs VIN=-20dB, 1KHz 70 84 - dB Output Source Current Open Loop Voltage Gain Common Mode Rejection Ratio CMRR1 PIN CONFIGURATION PIN DESCRIPTION Pin No. Symbol I/O Description 1 OUT1A O Drive output 2 OUT1B O Drive output 3 IN1A I Drive input 4 IN1B I Drive input 5 REG 6 REO O Regulator output 7 MUTE I Mute 8 GND -- Ground 9 IN2B I Drive input 10 IN2A I Drive input 11 OUT2B O Drive output Regulator HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http://www.silan.com.cn REV:1.2 2008.07.23 Page 3 of 11 SA1469TN Pin No. Symbol I/O Description 12 OUT2A O Drive output 13 GND -- Ground 14 OPOUT O Opamp output 15 OPIN (-) I Opamp input (-) 16 OPIN (+) I Opamp input (+) 17 OUT3A O Drive output 18 OUT3B O Drive output 19 IN3A I Drive input 20 IN3B I Drive input 21 VCC -- Supply voltage 22 VCC -- Supply voltage 23 VREF I 2.5V bias voltage 24 IN4B I Drive input 25 IN4A I Drive input 26 OUT4B O Drive output 27 OUT4A O Drive output 28 GND -- Ground FUNCTIONAL DESCRIPTION 1. MUTE Function Mute Thermal shutdown ○ External muting ○ VREF muting ○ 1) Operation conditions T≥175°C V(mute)≤ 1.4V Or open PIN23 < 0.7V The circuit is muted during thermal shutdown and during the mute-on state.In each case, only the drivers are muted. 2) During mute, the output pins remain at the internal bias voltage, roughly (Vcc-Vf)/2. 3) When the mute pin # 7 is open or the voltage of the mute pin # 7 is below 0.5V, the mute circuit is activated so that the output circuit will be muted.. 4) When the voltage of the mute pin is above 2V, the mute circuit is stopped and the output circuit is operated normally. 5) If the chip temperature rises above 175°C, then the TSD (Thermal Shutdown) circuit is activated and the output circuit is muted. 6) When the voltage of PIN23<0.7V ,the output circuit will be muted. HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http://www.silan.com.cn REV:1.2 2008.07.23 Page 4 of 11 SA1469TN 2. TSD (THERMAL SHUTDOWN) 1) The VREF is the output voltage of the band-gap-referenced biasing circuit and acts as the input voltage of the TSD circuit. 2) The base-emitter voltage of the TR, Qn is designed to turn-on at below voltage. VBE=VREF * R2/(R1+R2)=460mV 3) When the chip temperature rises up to 175°C, then the turn-on voltage of the Qn would drop down to 460mV. (Hysteresis: 25°) and, the Qn would turn on so the output circuit will be muted. 3. OP-AMP OP-Amp is integrated in the IC for user convenuence. OPIN(+) OPIN(-) OPOUT Pins 14, 15 and 16 may be left open when the operational amplifier is not used. 4. DRIVER 1) The voltage, VREF, is the reference voltage given by the BIAS voltage of the pin # 23. 2) The input signal through the pin # 3 is amplified by 10K/10K times and then fed to the level shift. 3) The level shift produces the current due to the difference between the input signal and the arbitrary reference signal. The current produced as +ΔV and -ΔV is fed into the driver buffer. 4) Driver buffer operates the power TR of the output stage according to the state of the input signal. 5) The output stage is the BTL driver and the motor is rotating in forward direction by operating TR Q1 and TR Q4. on the other hand, if TR Q2 and TR Q3 is operating, the motor is rotating in reverse direction. 6) When the input voltage through the pin # 3 is below the VREF, then the direction of the motor in forward direction. 7) When the input voltage through the pin # 3 is above the VREF, then the direction of the motor in reverse direction. 8) If it is desired to change the gain, then the pin # 4 or # 24 can be used. HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http://www.silan.com.cn REV:1.2 2008.07.23 Page 5 of 11 SA1469TN 5. RADIATION FIN IS CONNECTING TO THE INTERNAL GND OF THE PACKAGE. Connect the fin to the external GND. 6. REGULATOR This is a typical series regulator that generates a reference voltage internally. A PNP low saturation type transistor must be connected. HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http://www.silan.com.cn REV:1.2 2008.07.23 Page 6 of 11 SA1469TN TEST CIRCUIT HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http://www.silan.com.cn REV:1.2 2008.07.23 Page 7 of 11 SA1469TN SA1469TN TYPICAL APPLICATION CIRCUIT ELECTRICAL CHARACTERISTICS CURVES Fig.1 Driver I/O characteristics (variable load) HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http://www.silan.com.cn Fig.2 Driver I/O characteristics (variable power supply) REV:1.2 2008.07.23 Page 8 of 11 SA1469TN ELECTRICAL CHARACTERISTICS CURVES(Continued) Fig. 3 Power supply voltage vs. Fig. 4 Driver gain vs. temperature output offset voltage (RIN connected via gain adjustment pin) Fig. 5 Regulator voltage vs. temperature Fig. 6 Load current vs. regulator voltage Fig. 7 Operational amplifier vs. open loop HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http://www.silan.com.cn REV:1.2 2008.07.23 Page 9 of 11 SA1469TN PACKAGE OUTLINE HSOP-28-375-0.8 HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http://www.silan.com.cn UNIT: mm REV:1.2 2008.07.23 Page 10 of 11 SA1469TN ATTACH Revision History Data REV 2007.08.03 1.0 2007.10.26 1.1 2008.07.23 1.2 Description Original Add the” Power dissipation curve” 2 Modify the “Electrical Characteristics ” Modify the “Power dissipation curve” HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http://www.silan.com.cn Page REV:1.2 2008.07.23 Page 11 of 11