SMSC USB2244I

USB2244/USB2244I
Ultra Fast USB 2.0 SD/MMC
Flash Media Controller
Datasheet
PRODUCT FEATURES
General Description
Mask Programmable Features
The SMSC USB2244/USB2244i is a USB 2.0 compliant,
high speed Bulk Only Mass Storage Class Peripheral
Controller intended for reading and writing to SD/MMC Flash
Media Cards.
„
The SMSC USB2244/USB2244i is a fully integrated, single
chip solution capable of ultra high performance operation.
Average sustained transfer rates exceeding 35MB/s are
possible if the media and host can support those rates.
Provisions to read/write secure media formats is also
provided.
Software Features
General Features
„
„
„
„
„
„
„
„
„
„
„
36-pin QFN (6x6mm) lead-free RoHS compliant package
Hardware-controlled data flow architecture for all selfmapped media
Pipelined hardware support for access to non-selfmapped media
Product name with “i” denotes the version that supports
the industrial temperature range of -40ºC to 85ºC
Support included for secure media format on a licensed,
customized basis
— SD Secure
„
„
„
„
„
„
VID/PID/Language ID
28-character Manufacturer ID and Product string
12-hex digit (max) Serial Number string
Customizable Vendor specific data LED blink interval or
duration
Optimized for low latency interrupt handling
Reduced memory footprint
Please see the USB2244/USB2244i Software Release
Notes for additional Software Features.
Applications
„
Flash Media Card Reader/Writer
Printers
Desktop and Mobile PCs
Consumer A/V
Media Players/Viewers
Vista ReadyBoostTM
Compatible with Microsoft Vista, Windows XP, Windows
ME, Windows 2K SP4, Apple OSx, and Linux Mass
Storage Class Drivers
Hardware Features
„
Single Chip Flash Media Reader/Writer
— Secure Digital 2.0
–
HS-SD, HC-SD, TransFlash™ and reduced form factor
media
— MultiMediaCard Specification 4.2
–
„
„
„
„
„
„
„
„
„
1/4/8 bit MMC
SDIO and MMC Streaming Mode support
Extended configuration options
— Socket switch polarities, etc.
Media Activity LED
GPIO configuration and polarity
— Up to 8 GPIOs for special function use: LED indicators,
power control to memory devices, etc. The number of
actual GPIO’s depends on the implementation
configuration used.
— One GPIO with up to 200 mA drive
On Board 24MHz Crystal Driver Circuit
Internal Card Power FET
— 200mA
— "Fold-back" short circuit current protected
8051 8-bit microprocessor
— 60MHz - single cycle execution
— 64KB ROM; 14KB RAM
Internal Regulator for 1.8V core operation
Optimized pinout improves signal routing, easing
implementation and allowing for improved signal integrity
SMSC USB2244/USB2244i
DATASHEET
Revision 1.0 (05-27-08)
Ultra Fast USB 2.0 SD/MMC Flash Media Controller
Datasheet
ORDER NUMBER:
USB2244/USB2244i-AEZG-XX for 36 pin, QFN Lead-Free RoHS Compliant Package
“XX” in the order number indicates the internal ROM firmware revision level.
Please contact your SMSC sales representative for more information.
80 ARKAY DRIVE, HAUPPAUGE, NY 11788 (631) 435-6000, FAX (631) 273-3123
Copyright © 2008 SMSC or its subsidiaries. All rights reserved.
Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete
information sufficient for construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no
responsibility is assumed for inaccuracies. SMSC reserves the right to make changes to specifications and product descriptions at any time without notice.
Contact your local SMSC sales office to obtain the latest specifications before placing your product order. The provision of this information does not convey
to the purchaser of the described semiconductor devices any licenses under any patent rights or other intellectual property rights of SMSC or others. All sales
are expressly conditional on your agreement to the terms and conditions of the most recently dated version of SMSC's standard Terms of Sale Agreement
dated before the date of your order (the "Terms of Sale Agreement"). The product may contain design defects or errors known as anomalies which may cause
the product's functions to deviate from published specifications. Anomaly sheets are available upon request. SMSC products are not designed, intended,
authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury or severe property
damage. Any and all such uses without prior written approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the
customer. Copies of this document or other SMSC literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC’s website at
http://www.smsc.com. SMSC is a registered trademark of Standard Microsystems Corporation (“SMSC”). Product names and company names are the
trademarks of their respective holders.
SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES
ARISING FROM ANY COURSE OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT,
SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM
OF ACTION, WHETHER BASED ON CONTRACT; TORT; NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE;
WHETHER OR NOT ANY REMEDY OF BUYER IS HELD TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES.
SMSC USB2244/USB2244i
2
DATASHEET
Revision 1.0 (05-27-08)
Ultra Fast USB 2.0 SD/MMC Flash Media Controller
Datasheet
Table of Contents
Chapter 1 Acronyms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Chapter 2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Chapter 3 Pin Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.1
36-Pin Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Chapter 4 Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 5 Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.1
5.2
Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Buffer Type Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Chapter 6 Pin Reset State Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.1
36-Pin Reset States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Chapter 7 DC Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.1
7.2
7.3
7.4
Maximum Guaranteed Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended Operating Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
16
17
19
Chapter 8 AC Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
8.1
Oscillator/Clock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Chapter 9 Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Chapter 10 GPIO Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
SMSC USB2244/USB2244i
3
DATASHEET
Revision 1.0 (05-27-08)
Ultra Fast USB 2.0 SD/MMC Flash Media Controller
Datasheet
List of Figures
Figure 2.1
Figure 4.1
Figure 6.1
Figure 6.2
Figure 7.1
Figure 8.1
Figure 8.2
Figure 9.1
USB2244/USB2244i Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
USB2244/USB2244i 36 Pin QFN Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Pin Reset States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Legend for Pin Reset States Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Supply Rise Time Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Typical Crystal Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Formula to Find Value of C1 and C2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
USB2244/USB2244i 36-QFN, 6x6mm Body, 0.5mm Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Revision 1.0 (05-27-08)
4
DATASHEET
SMSC USB2244/USB2244i
Ultra Fast USB 2.0 SD/MMC Flash Media Controller
Datasheet
List of Tables
Table 3.1 USB2244/2244i 36-Pin QFN Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Table 5.2 USB2244/2244i 36-Pin QFN Pin Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Table 5.3 USB2244/USB2244i Buffer Type Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Table 6.1 USB2244/USB2244i Pin Reset States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Table 7.1 Pin Capacitance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Table 10.1 USB2244/USB2244i GPIO Usage (ROM Rev 0x00). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
SMSC USB2244/USB2244i
5
DATASHEET
Revision 1.0 (05-27-08)
Ultra Fast USB 2.0 SD/MMC Flash Media Controller
Datasheet
Chapter 1 Acronyms
MMC: MultiMediaCard
PLL: Phase-Locked Loop
QFN: Quad Flat no Leads
RoHS: Restriction of Hazardous Substances Directive
SD: Secure Digital
SDIO: Secure Digital Input/Output
SDC: Secure Digital Controllerl
SIE: Serial Interface Engine
*Note: In order to develop, make, use, or sell readers and/or other products using or incorporating any of the SMSC devices made
the subject of this document or to use related SMSC software programs, technical information and licenses under patent and other
intellectual property rights from or through various persons or entities, including without limitation media standard companies,
forums, and associations, and other patent holders may be required. These media standard companies, forums, and associations
include without limitation the following: Sony Corporation (Memory Stick, Memory Stick Pro); SD3 LLC (Secure Digital); MultiMedia
Card Association (MultiMediaCard); the SSFDC Forum (SmartMedia); the Compact Flash Association (Compact Flash); and Fuji
Photo Film Co., Ltd., Olympus Optical Co., Ltd., and Toshiba Corporation (xD-Picture Card). SMSC does not make such licenses
or technical information available; does not promise or represent that any such licenses or technical information will actually be
obtainable from or through the various persons or entities (including the media standard companies, forums, and associations), or
with respect to the terms under which they may be made available; and is not responsible for the accuracy or sufficiency of, or
otherwise with respect to, any such technical information.
SMSC's obligations (if any) under the Terms of Sale Agreement, or any other agreement with any customer, or otherwise, with
respect to infringement, including without limitation any obligations to defend or settle claims, to reimburse for costs, or to pay
damages, shall not apply to any of the devices made the subject of this document or any software programs related to any of such
devices, or to any combinations involving any of them, with respect to infringement or claimed infringement of any existing or future
patents related to solid state disk or other flash memory technology or applications ("Solid State Disk Patents"). By making any
purchase of any of the devices made the subject of this document, the customer represents, warrants, and agrees that it has
obtained all necessary licenses under then-existing Solid State Disk Patents for the manufacture, use and sale of solid state disk
and other flash memory products and that the customer will timely obtain at no cost or expense to SMSC all necessary licenses
under Solid State Disk Patents; that the manufacture and testing by or for SMSC of the units of any of the devices made the subject
of this document which may be sold to the customer, and any sale by SMSC of such units to the customer, are valid exercises of
the customer's rights and licenses under such Solid State Disk Patents; that SMSC shall have no obligation for royalties or otherwise
under any Solid State Disk Patents by reason of any such manufacture, use, or sale of such units; and that SMSC shall have no
obligation for any costs or expenses related to the customer's obtaining or having obtained rights or licenses under any Solid State
Disk Patents.
SMSC MAKES NO WARRANTIES, EXPRESS, IMPLIED, OR STATUTORY, IN REGARD TO INFRINGEMENT OR OTHER
VIOLATION OF INTELLECTUAL PROPERTY RIGHTS. SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES
AGAINST INFRINGEMENT AND THE LIKE.
No license is granted by SMSC expressly, by implication, by estoppel or otherwise, under any patent, trademark, copyright, mask
work right, trade secret, or other intellectual property right.
**To obtain this software program the appropriate SMSC Software License Agreement must be executed and in effect. Forms of
these Software License Agreements may be obtained by contacting SMSC.
Revision 1.0 (05-27-08)
6
DATASHEET
SMSC USB2244/USB2244i
Ultra Fast USB 2.0 SD/MMC Flash Media Controller
Datasheet
Chapter 2 Block Diagram
AUTO_
CBW
PROC
USB
Host
PHY
SIE
CTL
BUS
INTFC
BUS
INTFC
FMI
FMDU
CTL
SD/
MMC
Media
Interface
EP0 TX
EP0 RX
BUS
INTFC
RAM
4K
total
1.8V Reg
EP1 RX
EP1 TX
EP2 RX
EP2 TX
PLL
XDATA BRIDGE
+ BUS ARBITER
PWR_FET1
GPIOs
RAM
10KB
ROM
64KB
ADDR
MAP
GPIO10(CARD_PWR)
7 pins
Program
Memory
I/O Bus
Clock
Generation and
Control
SFR
RAM
8051
PROCESSOR
Figure 2.1 USB2244/USB2244i Block Diagram
SMSC USB2244/USB2244i
7
DATASHEET
Revision 1.0 (05-27-08)
Ultra Fast USB 2.0 SD/MMC Flash Media Controller
Datasheet
Chapter 3 Pin Table
3.1
36-Pin Package
Table 3.1 USB2244/2244i 36-Pin QFN Package
SD/MMC INTERFACE (12 Pins)
SD_D0
SD_D1
SD_D2
SD_D3
SD_D4
SD_D5
SD_D6
SD_D7
SD_CLK
SD_CMD
SD_WP
GPIO15 (SD_nCD)
USB INTERFACE (7 PINS)
USB+
USB-
RBIAS
XTAL1 (CLKIN)
XTAL2
VDDA33
VDD18PLL
MISC (13 PINS)
GPIO1 (LED1)
GPIO2 / RXD / SDA
GPIO4
GPIO7 / TXD / SCK
GPIO10 (CRD_PWR)
GPIO12
GPIO14
(4) NC
TEST
nRESET
DIGITAL, POWER (4 PINS)
(3)VDD33
VDD18
TOTAL 36
Revision 1.0 (05-27-08)
8
DATASHEET
SMSC USB2244/USB2244i
Ultra Fast USB 2.0 SD/MMC Flash Media Controller
Datasheet
GPIO2 / RXD / SDA
GPIO15 (SD_nCD)
SD_D2
GPIO12
SD_D3
VDD33
GPIO10 (CRD_PWR)
SD_D4
GPIO14
27
26
25
24
23
22
21
20
19
Chapter 4 Pin Configuration
TEST
28
18
nRESET
GPIO4
29
17
NC
SD _WP
30
16
NC
15
NC
14
VDD33
13
VDD18
12
NC
11
SD_CMD
10
SD_D5
6
7
8
9
SD_D7
SD_D6
SD_CLK
36
VDD33
VDDA33
5
35
SD_D0
RBIAS
Thermal Slug
(must be connected to VSS)
4
34
SD_D1
VDD18PLL
3
33
USB-
XTAL1 (CLKIN)
2
32
USB+
XTAL2
SMSC
USB2244/2244i
(Top View QFN-36)
1
31
GPIO1 (LED1)
GPIO7 / TXD / SCK
Indicates pins on the bottom of the device.
Figure 4.1 USB2244/USB2244i 36 Pin QFN Diagram
SMSC USB2244/USB2244i
9
DATASHEET
Revision 1.0 (05-27-08)
Ultra Fast USB 2.0 SD/MMC Flash Media Controller
Datasheet
Chapter 5 Pin Descriptions
This section provides a detailed description of each signal. The signals are arranged in functional
groups according to their associated interface.
The “n” symbol in the signal name indicates that the active, or asserted, state occurs when the signal
is at a low voltage level. When “n” is not present before the signal name, the signal is asserted at the
high voltage level.
The terms assertion and negation are used exclusively. This is done to avoid confusion when working
with a mixture of “active low” and “active high” signals. The term assert, or assertion, indicates that a
signal is active, independent of whether that level is represented by a high or low voltage. The term
negate, or negation, indicates that a signal is inactive.
5.1
Pin Descriptions
Table 5.2 USB2244/2244i 36-Pin QFN Pin Descriptions
NAME
SYMBOL
36-PIN
QFN
BUFFER
TYPE
DESCRIPTION
SECURE DIGITAL INTERFACE
SD Data
SD_D[7:0]
7
8
10
20
23
25
4
5
I/O12PU
The bi-directional signals should have weak
pull-up resistors. The register can be
controlled by: SD_MMC_INTF_EN bit of
SDC_MODE_CTL
SD Clock
SD_CLK
9
O12
This is an output clock signal to SD/MMC
device.
The clock frequency is software configurable.
SD Command
SD_CMD
11
I/O12PU
This is a bi-directional signal that connects to
the CMD signal of SD/MMC device. The bidirectional signal should have an internal weak
pull-up resistor.
The pull-up register can be controlled by:
SD_MMC_INTF_EN bit of SDC_MODE CTL
SD Write Protect
SD_nWP
30
I/O12
This pin is designated as the Secure Digital
card mechanical write detect pin.
SD Card Detect
GPIO
GPIO15
(SD_nCD)
26
I/O12
This is a GPIO designated as the Secure
Digital card detection pin.
USB INTERFACE
USB Bus Data
USB+
USB-
2
3
I/O-U
These pins connect to the USB bus data
signals.
USB Transceiver
Bias
RBIAS
35
I-R
A 12.0k , 1.0% resistor is attached from VSSA
to this pin in order to set the transceiver's
internal bias currents.
Revision 1.0 (05-27-08)
10
DATASHEET
SMSC USB2244/USB2244i
Ultra Fast USB 2.0 SD/MMC Flash Media Controller
Datasheet
Table 5.2 USB2244/2244i 36-Pin QFN Pin Descriptions (continued)
NAME
SYMBOL
36-PIN
QFN
BUFFER
TYPE
DESCRIPTION
24MHz Crystal
or external clock
input
XTAL1
(CLKIN)
33
ICLKx
This pin can be connected to one terminal of
the crystal or it can be connected to an external
24 clock when a crystal is not used.
24MHz Crystal
XTAL2
32
OCLKx
This is the other terminal of the crystal, or it can
be left open when an external clock source is
used to drive XTAL1(CLKIN). It may not be
used to drive any external circuitry other than
the crystal circuit.
3.3V Analog
Power
VDDA33
36
3.3V Analog Power
1.8V PLL Power
VDD18PLL
34
This pin is the 1.8V Power for the PLL.
+1.8V Filtered analog power for internal PLL.
This pin must have a 1.0μF(or greater) ±20%
(ESR <0.1Ω) capacitor to VSS.
MISC
General Purpose
I/O
GPIO1 (LED1)
1
I/O12
This pin may be used either as input, edge
sensitive interrupt input, or output.
In addition, as an output, the GPIO1 can use
output controlled by the LED1_GPIO1 register.
General Purpose
I/O
GPIO2 / RXD /
SDA
27
I/O12
GPIO: This pin may be used either as input,
edge sensitive interrupt input, or output.
I
RXD: In addition to the above, the signal can
be used as input to the RXD of UART in the
device, when the TXD_RXD_SEL bit in
UTIL_CONFIG1 register is cleared to "0".
I/O12
SDA: This is the data pin when used with an
external serial EEPROM.
General Purpose
I/O
GPIO4
29
I/O12
This pin may be used either as input, edge
sensitive interrupt input, or output.
General Purpose
I/O
GPIO7 /
TXD /
SCK
31
I/O12
GPIO: This pin may be used either as input,
edge sensitive interrupt input, or output.
O12
TXD: In addition, as an output, the GPIO7 can
be used as an output TXD of UART in the
device, when the GPIO2/TXD bit in
UTL_CONFIG register is set to "1"
O12
SCK: This is the clock output when used with
an external EEPROM.
I/O200
GPIO: This pin may be used either as input,
edge sensitive interrupt input, or output.
General Purpose
I/O
GPIO10
(CRD_PWR)
21
CRD_PWR: Card Power drive of 3.3V @ either
100mA or 200mA.
General Purpose
I/O
GPIO14
19
I/O12
This pin may be used either as input, edge
sensitive interrupt input, or output.
RESET Input
nRESET
18
IS
This active low signal is used by the system to
reset the chip. The active low pulse should be
at least 1μs wide.
SMSC USB2244/USB2244i
11
DATASHEET
Revision 1.0 (05-27-08)
Ultra Fast USB 2.0 SD/MMC Flash Media Controller
Datasheet
Table 5.2 USB2244/2244i 36-Pin QFN Pin Descriptions (continued)
NAME
SYMBOL
TEST Input
TEST
No Connects
NC
36-PIN
QFN
BUFFER
TYPE
28
I
DESCRIPTION
This signal is used for testing the chip. User
should normally tie this pin low externally if the
test function is not used.
No Connect. No trace or signal should be
routed/attached to these pins.
DIGITAL / POWER
+1.8V Core
power
VDD18
13
All VDD18 pins must be connected together on
the circuit board.
+1.8V core power. This pin must have a 1.0μF
(or greater) ±20% (ESR <0.1Ω) capacitor to
VSS.
3.3V Power &
Regulator Input.
VDD33
Ground
VSS
5.2
6
14
22
3.3V Power & Regulator Input.
SLUG
Ground Reference
Buffer Type Descriptions
Table 5.3 USB2244/USB2244i Buffer Type Descriptions
BUFFER
DESCRIPTION
I
Input.
IS
Input with Schmitt trigger.
I/O12
Input/Output buffer with 12mA sink and 12mA source.
I/O200
Input/Output buffer 12mA with FET disabled, 100/200mA source only when the FET is
enabled.
I/O12PU
Input/Output buffer with 12mA sink and 12mA source with a pull-up resistor.
O12
Output buffer with 12mA source.
ICLKx
XTAL clock input.
OCLKx
XTAL clock output.
I/O-U
Analog Input/Output Defined in USB specification.
I-R
RBIAS.
Revision 1.0 (05-27-08)
12
DATASHEET
SMSC USB2244/USB2244i
Ultra Fast USB 2.0 SD/MMC Flash Media Controller
Datasheet
Chapter 6 Pin Reset State Table
Hardware
Initialization
Voltage
Signal (v)
Firmware
Operational
RESET
VDD33
RESET
Time
(t)
VSS
Figure 6.1 Pin Reset States
LEGEND
yes
-z
pu
pd
hw
(fw)
VDD
none
hardware enables function
hardware disables function
hardware disables output driver
hardware enables pullup
hardware enables pulldown
hardware controls function, but state is protocol dependent
firmware controls function through registers
hardware supplies power through pin, applicable only to CARD_PWR pins
hardware disables pad
Figure 6.2 Legend for Pin Reset States Table
SMSC USB2244/USB2244i
13
DATASHEET
Revision 1.0 (05-27-08)
Ultra Fast USB 2.0 SD/MMC Flash Media Controller
Datasheet
6.1
36-Pin Reset States
Table 6.1 USB2244/USB2244i Pin Reset States
Post-Reset State
SD Mode
RESET STATE
PIN NAME
FUNCTION
OUTPUT
PU/
PD
INPUT
FUNCTION
OUTPUT
PU/
PD
INPUT
8
SD_D6
none
z
--
--
SD_D6
hw
pu
yes
7
SD_D7
none
z
--
--
SD_D7
hw
pu
yes
5
SD_D0
none
z
--
--
SD_D0
hw
pu
yes
4
SD_D1
none
z
--
--
SD_D1
hw
pu
yes
30
SD_WP
SD_WP
0
--
--
SD_WP
(fw)
(fw)
(fw)
25
SD_D2
none
z
--
--
SD_D2
hw
pu
yes
23
SD_D3
none
z
--
--
SD_D3
hw
pu
yes
20
SD_D4
none
z
--
--
SD_D4
hw
pu
yes
9
SD_CLK
none
z
--
--
SD_CLK
hw
--
yes
10
SD_D5
none
z
--
--
SD_D5
hw
pu
yes
11
SD_CMD
none
z
--
--
SD_CMD
hw
pu
yes
19
GPIO14
GPIO
z
pu
yes
26
GPIO15 (SD_nCD)
GPIO
z
pu
yes
24
GPIO12
GPIO
z
pu
yes
27
GPIO2 / RXD / SDA
GPIO
0
--
--
RXD
z
pu
yes
29
GPIO4
GPIO
0
--
--
31
GPIO7 / TXD / SCK
GPIO
0
--
--
TXD
hw
--
--
21
GPIO10(CARD_PWR)
GPIO
z
--
--
PWR
VDD
--
--
28
TEST
TEST
z
--
yes
18
nRESET
nRESET
z
--
yes
1
GPIO1 (LED1)
GPIO1
0
--
--
17:15
NC
none
z
--
--
none
z
--
--
12
NC
none
z
--
--
none
z
--
--
2
USB+
USB+
z
--
--
3
USB-
USB-
z
--
--
35
RBIAS
33
XTAL1 (CLKIN)
32
XTAL2
PIN
Revision 1.0 (05-27-08)
14
DATASHEET
SMSC USB2244/USB2244i
Ultra Fast USB 2.0 SD/MMC Flash Media Controller
Datasheet
Chapter 7 DC Parameters
7.1
Maximum Guaranteed Ratings
PARAMETER
SYMBOL
MIN
Storage
Temperature
TA
-55
MAX
UNITS
150
°C
325
°C
-0.5
4.0
V
Voltage on
USB+ and
USB- pins
-0.5
(3.3V supply voltage + 2) ≤ 6
V
Voltage on
GPIO10
-0.5
VDD33 + 0.3
V
Voltage on any
signal pin
-0.5
VDD33 + 0.3
V
Voltage on
XTAL1
-0.5
4.0
V
Voltage on
XTAL2
-0.5
VDD18 + 0.3
V
Lead
Temperature
3.3V supply
voltage
VDD33,
VDDA33
COMMENTS
Soldering < 10 seconds
When internal power FET
operation of this pin is enabled,
this pin may be simultaneously
shorted to ground or any
voltage up to 3.63V indefinitely,
without damage to the device
as long as VDD33 and VDDA33
are less than 3.63V and TA is
less than 70oC.
Note 7.1
Stresses above the specified parameters may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at any condition above
those indicated in the operation sections of this specification is not implied.
Note 7.2
When powering this device from laboratory or system power supplies, it is important that
the Absolute Maximum Ratings not be exceeded or device failure can result. Some power
supplies exhibit voltage spikes on their outputs when the AC power is switched on or off.
In addition, voltage transients on the AC power line may appear on the DC output. When
this possibility exists, it is suggested that a clamp circuit be used.
SMSC USB2244/USB2244i
15
DATASHEET
Revision 1.0 (05-27-08)
Ultra Fast USB 2.0 SD/MMC Flash Media Controller
Datasheet
Voltage
tRT
VDD33
3.3V
100%
90%
VSS
10%
t90%
t10%
Time
Figure 7.1 Supply Rise Time Model
7.2
Recommended Operating Conditions
PARAMETER
SYMBOL
MIN
MAX
UNITS
COMMENTS
Operating
Temperature
Commercial Part
TA
0
70
°C
Industrial Part
TA
-40
85
°C
3.3V supply voltage
VDD33,
VDDA33
3.0
3.6
V
3.3V supply rise time
tRT
0
400
μs
-0.3
5.5
V
Voltage on
USB+ and USB- pins
(Note 7.3)
If any 3.3V supply voltage drops
below 3.0V, then the MAX
becomes:
(3.3V supply voltage) + 0.5 ≤ 5.5
Voltage on any signal
pin
-0.3
VDD33
V
Voltage on XTAL1
-0.3
VDDA33
V
Voltage on XTAL2
-0.3
VDD18
V
Note 7.3
Revision 1.0 (05-27-08)
A 3.3V regulator with an output tolerance of 1% must be used if the output of the internal
power FET’s must support a 5% tolerance.
16
DATASHEET
SMSC USB2244/USB2244i
Ultra Fast USB 2.0 SD/MMC Flash Media Controller
Datasheet
7.3
DC Electrical Characteristics
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS
0.8
V
COMMENTS
I, IPU, IPD Type Input Buffer
Low Input Level
VILI
High Input Level
VIHI
Pull Down
PD
72
μA
Pull Up
PU
58
μA
2.0
TTL Levels
V
IS Type Input Buffer
Low Input Level
VILI
High Input Level
VIHI
Hysteresis
0.8
2.0
VHYSI
V
TTL Levels
V
420
mV
ICLK Input Buffer
Low Input Level
VILCK
High Input Level
VIHCK
1.4
IIL
-10
+10
μA
Low Input Leakage
IIL
-10
+10
μA
VIN = 0
High Input Leakage
IIH
-10
+10
μA
VIN = VDD33
0.4
V
IOL = 12mA @
VDD33= 3.3V
V
IOH = -12mA @
VDD33= 3.3V
μA
VIN = 0 to VDD33
(Note 7.4)
Input Leakage
0.5
V
V
VIN = 0 to VDD33
Input Leakage
(All I and IS buffers)
O12 Type Buffer
Low Output Level
VOL
High Output Level
VOH
VDD33
- 0.4
Output Leakage
IOL
-10
SMSC USB2244/USB2244i
17
DATASHEET
+10
Revision 1.0 (05-27-08)
Ultra Fast USB 2.0 SD/MMC Flash Media Controller
Datasheet
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS
COMMENTS
0.4
V
IOL = 12mA @
VDD33= 3.3V
V
IOH = -12mA @
VDD33= 3.3V
µA
VIN = 0 to VDD33
(Note 7.4)
I/O12, I/O12PU & I/O12PD Type
Buffer
Low Output Level
VOL
High Output Level
VOH
VDD33
- 0.4
Output Leakage
IOL
-10
Pull Down
PD
72
μA
Pull Up
PU
58
μA
+10
IO-U
(Note 7.5)
I-R
(Note 7.6)
I/O200
Integrated Power FET for
GPIO10
High Output Current Mode
IOUT
200
mA
VdropFET = 0.46V
Low Output Current Mode
(Note 7.7)
IOUT
100
mA
VdropFET = 0.23V
On Resistance
(Note 7.7)
RDSON
2.1
Ω
IFET = 70mA
Output Voltage Rise Time
tDSON
800
μs
CLOAD = 10μF
Supply Current Unconfigured
ICCINIT
80
90
mA
ICC
110
140
mA
ICC
135
165
mA
Supply Current Suspend
ICSBY
350
700
µA
Industrial Temperature Suspend
ICSBYI
350
900
µA
Supply Current Active
Full Speed
High Speed
Note 7.4
Output leakage is measured with the current pins in high impedance.
Note 7.5
See The USB 2.0 Specification, Chapter 7, for USB DC electrical characteristics
Note 7.6
RBIAS is a 3.3V tolerant analog pin.
Note 7.7
Output current range is controlled by program software, software disables FET during short
circuit condition.
Note 7.8
The assignment of each Integrated Card Power FET to a designated Card Connector is
controlled by both firmware and the specific board implementation. Firmware will default to
Revision 1.0 (05-27-08)
18
DATASHEET
SMSC USB2244/USB2244i
Ultra Fast USB 2.0 SD/MMC Flash Media Controller
Datasheet
the settings listed in Table 10.1, “USB2244/USB2244i GPIO Usage (ROM Rev 0x00),” on
page 22.
Note 7.9
7.4
The 3.3V supply should be at least at 75% of its operating condition before the 1.8V supply
is allowed to ramp up.
Capacitance
TA = 25°C; fc = 1MHz; VDD, VDDP = 1.8V
Table 7.1 Pin Capacitance
LIMITS
PARAMETER
Clock Input Capacitance
Input Capacitance
Output Capacitance
SMSC USB2244/USB2244i
SYMBOL
MIN
TYP
MAX
UNIT
TEST CONDITION
CXTAL
2
pF
All pins (except USB pins
and pins under test) are tied
to AC ground.
CIN
10
pF
COUT
20
pF
19
DATASHEET
Revision 1.0 (05-27-08)
Ultra Fast USB 2.0 SD/MMC Flash Media Controller
Datasheet
Chapter 8 AC Specifications
8.1
Oscillator/Clock
Crystal: Parallel Resonant, Fundamental Mode, 24 MHz ± 100ppm.
External Clock: 50% Duty cycle ± 10%, 24 MHz ± 100ppm, Jitter < 100ps rms.
XTAL1
(C S1 =
C B + C XTAL )
C1
Crystal
1Meg
CL
C2
XTAL2
(C S2 =
C B + C XTAL )
Figure 8.1 Typical Crystal Circuit
Note: CB equals total board/trace capacitance.
(C1 + CS1) x (C2 + CS2)
= CL
(C1 + CS1 + C2 + CS2)
Figure 8.2 Formula to Find Value of C1 and C2
Revision 1.0 (05-27-08)
20
DATASHEET
SMSC USB2244/USB2244i
Ultra Fast USB 2.0 SD/MMC Flash Media Controller
21
DATASHEET
SMSC USB2244/USB2244i
Figure 9.1 USB2244/USB2244i 36-QFN, 6x6mm Body, 0.5mm Pitch
Datasheet
Revision 1.0 (05-27-08)
Chapter 9 Package Outline
Ultra Fast USB 2.0 SD/MMC Flash Media Controller
Datasheet
Chapter 10 GPIO Usage
Table 10.1 USB2244/USB2244i GPIO Usage (ROM Rev 0x00)
NAME
ACTIVE LEVEL
GPIO1
H
LED1
LED indicator
GPIO2
H
RXD / SDA
Receive Port of Debugger / Serial
EEPROM Data
GPIO4
USER
GPIO
User defined
GPIO7
H
TXD / SCK
Transmit Port of Debugger / Serial
EEPROM Clock
GPIO10
L
CRD_PWR
Card Power Control
GPIO12
USER
GPIO
User defined
GPIO14
USER
GPIO
User defined
GPIO15
L
SD_nCD
Secure Digital card detect
Revision 1.0 (05-27-08)
SYMBOL
22
DATASHEET
DESCRIPTION AND NOTE
SMSC USB2244/USB2244i