SS6863 IR Preamplifier for Remote Control Systems FEATURES DESCRIPTION Only two external components required other than the photodiode. Easy to integrate into modules due to its small package size. Minimal chance of malfunction due to ambient light. Low power consumption. Band-pass filter center frequency set using an external resistor Microcomputer compatible. The SS6863 is a high-performance infra-red remote-control pre-amplifier, offering excellent interference-suppression capability. The infra-red pulses received by the photo-diode are processed by the trans-impedance amplifier and amplified by the AGC amplifier, limiter amplifier and band-pass filter. The evaluation stages that follow, including the comparator, Integrator and schmitttrigger, demodulate the transmitted digital signal. Reduced sensitivity to external interference is acheived by using short-term boost and long- APPLICATIONS term control circuits to prevent Interference IR remote control receivers for consumer from affecting the output. electronic products, such as TVs, VCRs, VCD/DVD players, audio devices, electric fans, air-conditioners, etc. TYPICAL APPLICATION CIRCUIT Vcc (+5V) 1 CA VCC 8 2 NC C1 0 .1µF VOUT FO 3 OUT AGND 6 4 DGND IN R1 7 110kΩ (fo=38kHz) 5 SS6863 Photo Diode IR Remote Control Receiver Rev.2.02 11/6/2003 www.SiliconStandard.com 1 of 6 SS6863 ORDERING INFORMATION PIN CONFIGURATION SS6863CXXX Packing TR: Tape and reel SO-8 TOP VIEW Package type S: SO-8 Example: VCC 1 8 NC 2 7 FO 3 6 AGND DGND 4 5 IN CA OUT SS6863CSTR $ in SO-8 package supplied on tape and reel ABSOLUTE MAXIMUM RATINGS Supply Voltage ......................................................................................... ............ 5.5V Input Voltage ...................................................................................................... 5V P-P Operating Temperature Range ....................................................................... -20°C ~ 80°C Storage Temperature Range ........................................................................... -65°C ~ 150°C TEST CIRCUIT Vcc (+5V) + 1 CA VCC 2 NC FO C1 VOUT 3 OUT 0.1µF AGND 4 DGND SS6863 8 7 R1 6 110K IN 5 S5 C3 + 0.47µF S4 S3 IIN 100µA S2 R2 47K + C2 0.47µF S1 Rev.2.02 11/6/2003 www.SiliconStandard.com VIN 2 of 6 SS6863 ELECTRICAL CHARACTERISTICS (VCC = 5V, TA = 25 °C unless ° otherwise specified) PARAMETER TEST CONDITIONS SYMBOL MIN. TYP. MAX. UNIT , , 72 25 22 , ,8.9 :5µ# , 1/ 74 77 , ,849 :.55µ# ,' .2 4. 4; , &&*, ,!* 5. 51 , <&*, ,! 7;5 7=7 , ,> .55µ,)+38kHz # ;0 /. ( (' .55µ,)+28kHz, 35kHz, 41kHz, 48kHz (note 1) #+ 7 = ( 52,)+ 38kHz (note 2) Rin 4 11 " #%8.9 .55µ,)+ 38kHz 055µs @+ 54" 105 245 0/5 µs " #%849 25,)+38kHz 055µs @+ 54" ' 275 0;5 /55 µs " .55µ,)+38kHz 055µs @+ 54" ! .55 425 755 µs µs k Ω .55µ,)+38kHz !!" 055µs @+ 54" ! .25 445 755 & .:5.µ' *- 5/ ,-s A 57 5; .5 # @.B!#*at 35kHz and the AC level at 28kHz denotes AQ1. 35kHz) #+: log 28kHz) !#* 41kHz#*48kHz denotes AQ2. kHz) #+': log kHz) @4B*,*,,+ k Ω : Rev.2.02 11/6/2003 www.SiliconStandard.com 3 of 6 SS6863 BLOCK DIAGRAM "#!.# -(*//* !#!* (- # $ - !"# * % $ & ! PIN DESCRIPTIONS @.B # $& @4B @ $@ @1B C $ @7B ">@" $" @2B @ $8 9 @0B #>@" $# @;B ' $(! ! @/B , $ APPLICATION INFORMATION !"# %) !$ ##(&8# (&*9 % ** $!"$# ! % % % * ! $ ! + % %*#+ %! %*! $! ! * !"# $ !*$ * ! %$ ! !!! + ! % $ ! $ ! %$ ! ! % $ % !!! Rev.2.02 11/6/2003 www.SiliconStandard.com 4 of 6 SS6863 ! * ! * % $%!&! %* ! ! % $ ! ; , $ C ! $ ! ! % ! D!!$!$ ! % ! * ! * % 7+ ! % ! ! !! ! %%B !$ !8?<9 % "# .8?Ω9 $% * !* ! ! $' * $ ! ! !! $ F * 57 8*+ $ * % % ! ! 9+ * +$ 57+ $ "# * ! $ $ * E % $ ! % * # < *!* $ % ! *$ ! ! #> ! ! ! * *% * ! . +!(+%!$ $ ! $ % . $ *!%!*$ $$ ! . * * #>@" + ">@" !#>! % % G H ! ! Rev.2.02 11/6/2003 www.SiliconStandard.com 5 of 6 SS6863 PHYSICAL DIMENSIONS #" I(& @ #J # .12 .;2 #. 5.5 542 ( 511 52. 5.= 542 " 7/5 255 1/5 755 .4;8I9 < 2/5 045 & 575 .4; Information furnished by Silicon Standard Corporation is believed to be accurate and reliable. However, Silicon Standard Corporation makes no guarantee or warranty, express or implied, as to the reliability, accuracy, timeliness or completeness of such information and assumes no responsibility for its use, or for infringement of any patent or other intellectual property rights of third parties that may result from its use. Silicon Standard reserves the right to make changes as it deems necessary to any products described herein for any reason, including without limitation enhancement in reliability, functionality or design. No license is granted, whether expressly or by implication, in relation to the use of any products described herein or to the use of any information provided herein, under any patent or other intellectual property rights of Silicon Standard Corporation or any third parties. Rev.2.02 11/6/2003 www.SiliconStandard.com 6 of 6