PSA1200A-LF 9939 Via Pasar • San Diego, CA 92126 TEL (858) 621-2700 FAX (858) 621-2722 VOLTAGE CONTROLLED OSCILLATOR Rev A1 £(f) (dBc/Hz) PHASE NOISE (1 Hz BW, typical) FEATURES • Frequency Range: 1200 - 1200 MHz • Tuning Voltage: Vdc • PLL-24 - Style Package APPLICATIONS • Basestations • Satellite Communications • OFFSET (Hz) VALUE UNITS 1200 - 1200 MHz Phase Noise @ 10 kHz offset (1 Hz BW, typ.) -103 dBc/Hz Harmonic Suppression (2nd, typ.) Tuning Voltage Tuning Sensitivity (avg.) -15 5000 dBc Vdc MHz/V Power Output 0±3 dBm Load Impedance 50 PERFORMANCE SPECIFICATIONS Oscillation Frequency Range Input Capacitance (max.) 1000 pF Pushing 2 MHz/V Pulling ( 14dB Return Loss, Any Phase) 2 MHz Operating Temperature Range 0 to 60 °C Package Style PLL-24 POWER SUPPLY REQUIREMENTS Supply Voltage (Vcc, nom.) Supply Current (Icc, typ.) 5 Vdc 33 mA All specifications are typical unless otherwise noted and subject to change without notice. APPLICATION NOTES • AN-100/1 : Mounting and Grounding of VCOs • AN-102 : Proper Output Loading of VCOs • AN-107 : How to Solder Z-COMM VCOs NOTES: Reference Oscillator Signal: 5 MHz< <100 MHz Frequency Synthesizer: Analog Devices - ADF4106 © Z-Communications, Inc. LOW COST - HIGH PERFORMANCE Page 1 All rights reserved PSA1200A-LF VOLTAGE CONTROLLED OSCILLATOR PAGE 2 TUNING CURVE, typ. FREQUENCY (MHz) 1230 1210 1190 60 1170 25 1150 0 °c °c °c 1130 1110 1090 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 TUNING VOLTAGE (Vdc) POWER OUTPUT (dBm) POWER CURVE, typ. 5 4 3 2 1 60 0 25 0 -1 °c °c °c -2 -3 1103 1123 1140 1155 1168 1181 1194 1206 1218 1231 FREQUENCY (MHz) PHYSICAL DIMENSIONS PLL-24 415-0089 REV. A (DRAWING NOT TO SCALE) 0.140 24 23 22 21 20 0.606 0.631 0.481 0.396 0.311 0.226 0.141 0.000 0.026 1 DETAIL A 19 2 TABS RANGE: SEE NOTE 5 (4 PLACES) 18 3 17 16 4 TOP 5 0.000 15 6 14 7 13 0.025 0.178 PIN 1 8 0.263 .055 0.348 0.433 0.518 .032 BOTTOM 0.603 .015 .030 SEE DETAIL A 0.688 0.841 DETAIL B (TYP) 0.866 (8 PLACES) SEE DETAIL B © Z-Communications, Inc. Page 2 1. The inside radius of all 24 half holes at the perimeter of the board are plated to provide a surface for the attachment of the PLL Module to the PCB. 16 pads are for grounding, 8 pads are for signal interface. 2. The surface of the shield is tin-plated and may be soldered to. The shield's base metal is cold rolled steel. 3.The ground plane on the bottom side is ground and attaches to a ground track on the top side of the board as well as to the shield. 4. Unless otherwise noted all dimensions are in inches. 5. Unless otherwise noted all tolerances are as follows: .xxx = ± .010 9 10 11 12 P1 P2-4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18-24 RF OUTPUT GROUND REFERENCE OSCILLATOR INPUT GROUND CLOCK DATA GROUND LOAD ENABLE GROUND LOCK DETECT VCC GROUND GROUND GROUND NO CONNECTION GROUND Printed in the U.S.A.