Advanced Monolithic Systems AMS2954 250mA LOW DROPOUT VOLTAGE REGULATOR RoHS compliant FEATURES APPLICATIONS • 2.5V, 3.0V, 3.3V and 5.0V Versions • High Accuracy Output Voltage • Extremely Low Quiescent Current • Low Dropout Voltage • Extremely Tight Load and Line Regulation • Very Low Temperature Coefficient • Current and Thermal Limiting • Needs Minimum Capacitance (1µF) for Stability • Unregulated DC Positive Transients 60V • Battery Powered Systems • Portable Consumer Equipment • Cordless Telephones • Portable (Notebook) Computers • Portable Instrumentation • Radio Control Systems • Automotive Electronics • Avionics • Low-Power Voltage Reference ADDITIONAL FEATURES (ADJ ONLY) • 1.24V to 29V Programmable Output • Error Flag Warning of Voltage Output Dropout • Logic Controlled Electronic Shutdown GENERAL DESCRIPTION The AMS2954 series are micropower voltage regulators ideally suited for use in battery-powered systems. These devices feature very low quiescent current (typ.75µA), and very low dropout voltage (typ.50mV at light loads and 380mV at 250mA) thus prolonging battery life. The quiescent current increases only slightly in dropout. The AMS2954 has positive transient protection up to 60V and can survive unregulated input transient up to 20V below ground. The AMS2954 was designed to include a tight initial tolerance (typ. 0.5%), excellent load and line regulation (typ. 0.05%), and a very low output voltage temperature coefficient, making these devices useful as a low-power voltage reference. The AMS2954 is available in the 3L TO-220 package, 3L TO-263, SOT-223, TO-252 and in 8-pin plastic SOIC and DIP packages. In the 8L SOIC and PDIP packages the following additional features are offered: an error flag output warns of a low output voltage, often due to failing batteries on input; the logic-compatible shutdown input enables the regulator to be switched on and off; the device may be pin-strapped for a, 2.5, 3.0V, 3.3V or 5V output, or programmed from 1.24V to 29V with an external pair of resistors. ORDERING INFORMATION PACKAGE TYPE OPERATING 8 LEAD SOIC 8 LEAD PDIP TEMP. RANGE 3 LEAD TO-220 3 LEAD TO-263 TO-252 SOT-223 AMS2954ACT-X AMS2954ACM-X AMS2954ACD-X AMS2954AC-X AMS2954ACS-X AMS2954CP-X IND. AMS2954CT-X AMS2954CM-X AMS2954CD-X AMS2954C-X AMS2954CS-X AMS2954CP-X IND X = 2.5V, 3.0V, 3.3V, 5.0V SOT-223 TOP VIEW 3L TO-220 FRONT VIEW PIN CONNECTIONS TAB IS GND 1 SENSE 2 SHUTDOWN 3 GROUND 4 8 INPUT OUTPUT 2 GND INPUT 1 8L SOIC/ 8L PDIP OUTPUT 1 3 2 3 INPUT GND OUTPUT 7 FEEDBACK 6 VTAP TO-252 FRONT VIEW 5 ERROR TAB IS GND 3 2 1 OUTPUT INPUT Advanced Monolithic Systems, Inc. www.advanced-monolithic.com 3L TO-263 FRONT VIEW TAB IS GND 3 OUTPUT 2 GND 1 INPUT Phone (925) 443-0722 Fax (925) 443-0723 AMS2954 ABSOLUTE MAXIMUM RATINGS (Note 1) Input Supply Voltage SHUTDOWN Input Voltage, Error Comparator Output Voltage,(Note 9) FEEDBACK Input Voltage (Note 9) (Note 10) Power Dissipation Junction Temperature Storage Temperature ESD -0.3 to +30V Soldering Temperature (25 sec) 265°C -1.5 to +30V OPERATING RATINGS (Note 1) Internally Limited +150°C -65°C to +150°C 2kV Max. Input Supply Voltage Junction Temperature Range (TJ) (Note 8) AMS2954AC-X AMS2954C-X 40V -40°C to +125°C ELECTRICAL CHARACTERISTICS at Vs=Vout+1V, Ta=25°C, unless otherwise noted. AMS2954AC Parameter AMS2954C Conditions (Note 2) Min. Typ. Max. Min. Typ. Max. Units 2.5 V Versions (Note 16) Output Voltage Output Voltage TJ = 25°C (Note 3) -25°C ≤TJ ≤85°C Full Operating Temperature Range 100 µA ≤IL ≤250 mA TJ ≤TJMAX 2.488 2.5 2.512 2.475 2.5 2.525 V 2.475 2.5 2.525 2.450 2.5 2.550 V 2.470 2.5 2.530 2.440 2.5 2.560 V 2.463 2.5 2.537 2.448 2.5 2.562 V 2.985 3.0 3.015 2.970 3.0 3.030 V 2.970 3.0 3.030 2.955 3.0 3.045 V 2.964 3.0 3.036 2.940 3.0 3.060 V 2.958 3.0 3.042 2.928 3.0 3.072 V 3.284 3.3 3.317 3.267 3.3 3.333 V 3.267 3.3 3.333 3.251 3.3 3.350 V 3.260 3.3 3.340 3.234 3.3 3.366 V 3.254 3.3 3.346 3.221 3.3 3.379 V 4.975 5.0 5.025 4.95 5.0 5.05 V 4.95 5.0 5.050 4.925 5.0 5.075 V 4.94 5.0 5.06 4.90 5.0 5.10 V 4.925 5.0 5.075 4.88 5.0 5.12 V 3.0 V Versions (Note 16) Output Voltage Output Voltage TJ = 25°C (Note 3) -25°C ≤TJ ≤85°C Full Operating Temperature Range 100 µA ≤IL ≤250 mA TJ ≤TJMAX 3.3 V Versions (Note 16) Output Voltage Output Voltage TJ = 25°C (Note 3) -25°C ≤TJ ≤85°C Full Operating Temperature Range 100 µA ≤IL ≤250 mA TJ ≤TJMAX 5 V Versions (Note 16) Output Voltage Output Voltage TJ = 25°C (Note 3) -25°C ≤TJ ≤85°C Full Operating Temperature Range 100 µA ≤IL ≤250 mA TJ ≤TJMAX All Voltage Options Output Voltage Temperature Coefficient Line Regulation (Note 14) (Note 12) (Note 4) 6V ≤Vin ≤30V (Note 15) 20 100 50 150 ppm/°C 0.03 0.1 0.04 0.2 % Load Regulation (Note 14) 100 µA ≤IL ≤ 250 mA 0.04 0.16 0.1 0.2 % Advanced Monolithic Systems, Inc. www.advanced-monolithic.com Phone (925) 443-0722 Fax (925) 443-0723 AMS2954 ELECTRICAL CHARACTERISTICS (Note 2) (Continued) AMS2954AC PARAMETER Min. (Note 2) Dropout Voltage (Note 5) AMS2954C CONDITIONS Typ. IL = 100µ A IL = 250 mA Max. Min. Typ. Max. Units 50 80 50 80 mV 380 600 380 600 mV 75 120 75 120 µA 15 20 15 20 mA Vout = 0 200 500 200 500 mA Thermal Regulation (Note 13) 0.05 0.2 0.05 0.2 %/W Output Noise, 10Hz to 100KHz CL = 1µF 430 430 µV rms 160 160 µV rms 100 100 µV rms AMS2954AC AMS2954C Ground Current Current Limit IL = 100 µA IL = 250 mA CL = 200 µF CL = 13.3 µF (Bypass = 0.01 µF pins 7 to 1) 8-Pin Versions only Reference Voltage Reference Voltage 1.22 Over Temperature (Note 7) Feedback Pin Bias Current Reference Voltage Temperature Coefficient 1.26 V 1.285 V 60 nA 20 50 ppm/°C 0.1 0.1 nA/°C 40 V OH = 30V 1.21 1.185 60 1.235 40 0.01 1 0.01 1 µA 150 250 150 250 mV Output Low Voltage Vin = 4.5V IOL = 400µA Upper Threshold Voltage (Note 6) Lower Threshold Voltage (Note 6) 75 Hysteresis Shutdown Input (Note 6) 15 Input logic Voltage 1.25 1.27 ( Note 12 ) Feedback Pin Bias Current Temperature Coefficient Error Comparator Output Leakage Current 1.235 1.19 Low (Regulator ON) High (Regulator OFF) 40 60 1.3 40 95 60 75 mV 95 15 0.7 2 mV mV 1.3 0.7 V 2 V Shutdown Pin Input Current (Note 3) Vs = 2.4V Vs = 30V 30 450 50 600 30 450 50 600 µA Regulator Output Current in Shutdown (Note 3) (Note 11) 3 10 3 10 µA Note 1: Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which operation of the device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions, see the Electrical Characteristics tables. Note 2: Unless otherwise specified all limits guaranteed for VIN = ( VONOM +1)V, IL = 100 µA and CL = 1 µF for 5V versions and 2.2µF for 3V and 3.3V versions. Limits appearing in boldface type apply over the entire junction temperature range for operation. Limits appearing in normal type apply for TA = TJ = 25°C Additional conditions for the 8-pin versions are FEEDBACK tied to VTAP, OUTPUT tied to SENSE and VSHUTDOWN ≤ 0.8V. Note 3: Guaranteed and 100% production tested. Note 4: Guaranteed but not 100% production tested. These limits are not used to calculate outgoing AQL levels. Note 5: Dropout voltage is defined as the input to output differential at which the output voltage drops 100 mV below its nominal value measured at 1V differential. At very low values of programmed output voltage, the minimum input supply voltage of 2V ( 2.3V over temperature) must be taken into account. Note 6: Comparator thresholds are expressed in terms of a voltage differential at the feedback terminal below the nominal reference voltage measured at VIN = ( VONOM +1)V. To express these thresholds in terms of output voltage change, multiply by the error amplifier gain = Vout/Vref = (R1 + R2)/R2. For example, at a programmed output voltage of 5V, the error output is guaranteed to go low when the output drops by 95 mV x 5V/1.235 = 384 mV. Thresholds remain constant as a percent of Vout as Vout is varied, with the dropout warning occurring at typically 5% below nominal, 7.5% guaranteed. Note 7: Vref ≤Vout ≤ (Vin - 1V), 2.3 ≤Vin≤30V, 100µA≤IL≤ 250 mA, TJ ≤ TJMAX. Advanced Monolithic Systems, Inc. www.advanced-monolithic.com Phone (925) 443-0722 Fax (925) 443-0723 µA AMS2954 Note 8: The junction-to-ambient thermal resistance are as follows:60°C/W for the TO-220 (T), 73°C/W for the TO-263 (M), 80°C/W for the TO-252 (D), 90°C/W for the SOT-223 (with package soldering to copper area over backside ground plane or internal power plane ϕ JA can vary from 46°C/W to >90°C/W depending on mounting technique and the size of the copper area), 105°C/W for the molded plastic DIP (P) and 160°C/W for the molded plastic SO-8 (S). Note 9: May exceed input supply voltage. Note 10: When used in dual-supply systems where the output terminal sees loads returned to a negative supply, the output voltage should be diode-clamped to ground. Note 11: Vshutdown ≥ 2V, Vin ≤ 30V, Vout =0, Feedback pin tied to 5VTAP. Note 12: Output or reference voltage temperature coefficients defined as the worst case voltage change divided by the total temperature range. Note 13: Thermal regulation is defined as the change in output voltage at a time T after a change in power dissipation is applied, excluding load or line regulation effects. Specifications are for a 50mA load pulse at VIN =30V (1.25W pulse) for T =10 ms. Note 14: Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output voltage due to heating effects are covered under the specification for thermal regulation. Note 15: Line regulation for the AMS2954 is tested at 150°C for IL = 1 mA. For IL = 100 µA and TJ = 125°C, line regulation is guaranteed by design to 0.2%. See typical performance characteristics for line regulation versus temperature and load current. BLOCK DIAGRAM AND TYPICAL APPLICATIONS AMS2954-XX 3 Lead Packages AMS2954-XX 8 Lead Packages VOUT IL≤ 150mA UNREGULATED DC UNREGULATED DC + INPUT 7 FEEDBACK + VOUT IL≤ 150mA OUTPUT 8 INPUT 1 OUTPUT 2 + - + SENSE + ERROR AMPLIFIER 1.23V REFERENCE + SEE APPLICATION HINTS FROM CMOS OR TTL - 3 SHUTDOWN + 50mV + GROUND ERROR AMPLIFIER 6 VTAP 330kΩ TO CMOS OR TTL ERROR 4 GROUND ERROR DETECTION COMPARATOR Advanced Monolithic Systems, Inc. www.advanced-monolithic.com Phone (925) 443-0722 SEE APPLICATION HINTS 5 + 1.23V REFERENCE + Fax (925) 443-0723 AMS2954 TYPICAL PERFORMANCE CHARACTERISTICS Quiescent Current Dropout Characteristics 20 Input Current 6 250 225 10 1 50 100 150 200 LOAD CURRENT (mA) 1 3 IO=250mA 2 1 0 250 IO=1mA 2 3 4 5 6 7 8 INPUT VOLTAGE (V) 50 1 9 10 5.02 5.0 4.98 0.2% 4.96 120 IL= 1 mA 100 80 IL= 0mA 60 40 20 4.94 -75 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (° C) 90 80 70 60 50 -75 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (° C) QUIESCENT CURRENT (mA) VIN= 6V 100 9 10 5V OUTPUT 0 0 1 Quiescent Current IL= 100µA 2 3 4 5 6 7 8 INPUT VOLTAGE (V) 140 8 24 5V OUTPUT 5V OUTPUT 30 25 20 2 3 4 5 6 7 INPUT VOLTAGE (V) Quiescent Current 35 5V OUTPUT 0 Quiescent Current QUIESCENT CURRENT (µA) OUTPUT VOLTAGE (V) INPUT CURRENT (mA) 6 5.04 Quiescent Current QUIESCENT CURRENT (µA) 75 5V OUTPUT IO=250mA 1 RL= ∞ 160 5V OUTPUT 0 125 100 25 0 5.06 120 110 3 4 5 2 INPUT VOLTAGE (V) 175 150 Temperature Drift of 3 Representative Units Input Current 270 240 210 180 150 120 90 75 60 45 30 15 0 1 0 5V OUTPUT 200 VIN= 6V IL= 250mA 15 10 5 -75 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (° C) Advanced Monolithic Systems, Inc. www.advanced-monolithic.com QUIESCENT CURRENT (mA) 0.1 4 INPUT CURRENT (µA) OUTPUT VOLTAGE (V) GROUND CURRENT (mA) 5V OUTPUT 5 21 18 15 IL= 250mA 12 9 6 3 0 0 Phone (925) 443-0722 1 2 3 4 5 6 7 INPUT VOLTAGE (V) Fax (925) 443-0723 8 AMS2954 TYPICAL PERFORMANCE CHARACTERISTICS (Continued) Short Circuit Current 300 250 200 150 100 -75 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (° C) 500 400 300 ~ ~ 100 50 AMS2954 Minimum Operating Voltage 2.1 10 1.8 1.7 400 300 200 TJ = 25°C 100 0 100µA AMS2954 Feedback Bias Current 20 1.9 IL= 100µA 0 -75 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (° C) 2.2 2.0 IL= 250mA 0 -10 -20 10mA 100mA OUTPUT CURRENT 250mA AMS2954 Feedback Pin Current 50 FEEDBACK CURRENT (µA) 350 500 DROPOUT VOLTAGE (mV) DROPOUT VOLTAGE (mV) 400 BIAS CURRENT (nA) PIN 7 DRVEN BY EXTERNAL SOURCE (REGULATOR RUN OPEN LOOP) 0 -50 TA = 125°C -100 -150 TA = 25°C -200 TA = -55°C AMS2954 Error Comparator Output AMS2954 Comparator Sink Current 2.5 7 50k RESISTOR TO EXTERNAL 5V SUPPLY 6 5 4 HYSTERESIS 3 50k RESISTOR TO V OUT 2 1 0 0 1 2 3 4 5 6 7 INPUT VOLTAGE (V) 8 SINK CURRENT (mA) VOUT= 5V 8 -250 -2.0 -30 -75 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (° C) 1.6 -75 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (° C) 2.0 1.5 TA = 125°C TA = 25°C 1.0 TA = -55°C 0.5 0.0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 OUTPUT LOW VOLTAGE (V) Advanced Monolithic Systems, Inc. www.advanced-monolithic.com INPUT OUTPUT VOLTAGE VOLTAGE CHANGE SHORT CIRCUIT CURRENT (mA) MINIMUM OPERATING VOLTAGE (V) 600 9 ERROR OUTPUT (V) Dropout Voltage Dropout Voltage 450 0 0.5 1.0 -1.5 -1.0 -0.5 FEEDBACK VOLTAGE (V) Line Transient Response 100 mV 50 mV 0 -50 mV CL= 1µF IL= 1mA ~ ~ VOUT= 5V 8V 6V 4V Phone (925) 443-0722 0 200 400 TIME (µs) 600 Fax (925) 443-0723 800 AMS2954 TYPICAL PERFORMANCE CHARACTERISTICS (Continued) 250 mA 100 µA 1 2 3 TIME (ms) 4 5 0 RIPPLE REJECTION (dB) 0.5 VOUT = 5V CL= 1 µF 0.05 0.02 0.01 16 OUTPUT VOLTAGE (V) 20 4 3 2 1 0 2 80 70 IL= 0 50 IL= 100µA CL= 1 µF VIN= 6V VOUT = 5V 30 ~ ~ Ripple Rejection 80 40 CL= 10 µF IL= 10 mA VIN = 8V VOUT = 5V 0 -2 -100 0 100 200 300 400 500 600 700 TIME (µs) 90 60 CL= 1 µF 5 90 70 CL= 1 µF VIN= 6V VOUT = 5V IL= 1mA 60 50 40 30 IL= 10mA 10 10K 100K 100 1K FREQUENCY (Hz) 20 101 1M Ripple Rejection 60 IL= 50mA IL= 250mA 50 40 CL= 1µF VIN= 6V 30 VOUT= 5V 20 10 101 10 3.5 VOLTAGE NOISE SPECTRAL DENSITY(mV/√Hz) 70 2 102 105 103 104 FREQUENCY (Hz) 3 105 4 10 10 FREQUENCY (Hz) 20 101 106 AMS2954 Output Noise 80 RIPPLE REJECTION (dB) 8 12 TIME (ms) 106 5V OUTPUT IL= 250mA CL= 1 µF 2.5 2.0 CL= 3.3 µF CL= 220 µF 1.0 0.5 0.0 0.01 µF BYPASS PIN 1 TO PIN 7 102 10 105 103 104 FREQUENCY (Hz) 106 AMS2954 Divider Resistance 3.0 1.5 2 400 PIN 2 TO PIN 4 RESISTANCE (kΩ) OUPUT IMPEDANCE (Ω) IO= 250mA IO= 1 mA 0.2 0.1 4 7 6 Ripple Rejection IO= 100µA 2 1 VOUT = 5V ~ ~ Output Impedance 10 5 CL= 10 µF RIPPLE REJECTION (dB) 0 250 mA 100 µA AMS2954 Enable Transient SHUTDOWN PIN VOLTAGE (V) CL= 1 µF VOUT = 5V ~ ~ OUTPUT VOLTAGE CHANGE (mV) Load Transient Response 80 60 40 20 0 -20 -40 -60 LOAD CURRENT LOAD CURRENT OUTPUT VOLTAGE CHANGE (mV) Load Transient Response 250 200 150 100 50 0 -50 -100 103 104 FREQUENCY (Hz) Advanced Monolithic Systems, Inc. www.advanced-monolithic.com 105 300 200 100 0 -75 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (° C) Phone (925) 443-0722 Fax (925) 443-0723 AMS2954 TYPICAL PERFORMANCE CHARACTERISTICS (Continued) 1.6 REGULATOR OFF 1.2 1.0 REGULATOR ON 0.8 0.6 -75 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (° C) 30 25 20 15 10 5 0 300 OUTPUT CURRENT (mA) 1.8 1.4 AMS2954 Maximum Rated Output Current Line Regulation OUTPUT VOLTAGE CHANGE (V) SHUTDOWN TRESHOLD VOLTAGE (V) Shutdown Treshold Voltage IL= 100µA T J = 150° C IL= 1mA ~ ~ 10 5 0 -5 -10 IL= 100µA TJ = 125° C 15 20 25 10 INPUT VOLTAGE (V) 200 TJMAX= 125° C 150 TA= 25° C 100 TA= 85° C 0 25 30 POWER OUTPUT VOLTAGE DISSIPATION (W) CHANGE (mV) OUTPUT CURRENT (mA) 250 SOT-223 PACKAGE SOLDERED TO PC BOARD 10 5 15 20 INPUT VOLTAGE (V) T JMAX= 125° C VOUT = 5V 200 TA= 25° C 150 TA= 50° C 100 50 T A= 85° C 30 10 5 15 20 INPUT VOLTAGE (V) 0 Thermal Response 300 0 250 0 5 AMS2954 Maximum Rated Output Current 50 8 PIN MOLDED DIP SOLDERED TO PC BOARD Advanced Monolithic Systems, Inc. www.advanced-monolithic.com 5 4 2 0 -2 1 ~ ~ 1.25W 0 -1 0 10 20 30 TIME (µs) Phone (925) 443-0722 40 50 Fax (925) 443-0723 25 30 AMS2954 APPLICATION HINTS External Capacitors A 1.0 µF or greater capacitor is required between output and ground for stability at output voltages of 5V or more. At lower output voltages, more capacitance is required (2.2µ or more is recommended for 2.5V, 3.0V and 3.3V versions). Without this capacitor the part will oscillate. Most types of tantalum or aluminum electrolytic works fine here; even film types work but are not recommended for reasons of cost. Many aluminum types have electrolytes that freeze at about -30°C, so solid tantalums are recommended for operation below -25°C. The important parameters of the capacitor are an ESR of about 5 Ω or less and resonant frequency above 500 kHz parameters in the value of the capacitor. The value of this capacitor may be increased without limit. At lower values of output current, less output capacitance is required for stability. The capacitor can be reduced to 0.33 µF for currents below 10 mA or 0.1 µF for currents below 1 mA. Using the adjustable versions at voltages below 5V runs the error amplifier at lower gains so that more output capacitance is needed. For the worst-case situation of a 300mA load at 1.23V output (Output shorted to Feedback) a 3.3µF (or greater) capacitor should be used. Unlike many other regulators, the AMS2954, will remain stable and in regulation with no load in addition to the internal voltage divider. This is especially important in CMOS RAM keep-alive applications. When setting the output voltage of the AMS2954 version with external resistors, a minimum load of 1µA is recommended. A 1µF tantalum or aluminum electrolytic capacitor should be placed from the AMS2954/AMS2954 input to the ground if there is more than 10 inches of wire between the input and the AC filter capacitor or if a battery is used as the input. Stray capacitance to the AMS2954 Feedback terminal can cause instability. This may especially be a problem when using a higher value of external resistors to set the output voltage. Adding a 100 pF capacitor between Output and Feedback and increasing the output capacitor to at least 3.3 µF will fix this problem. Error Detection Comparator Output The comparator produces a logic low output whenever the AMS2954 output falls out of regulation by more than approximately 5%. This figure is the comparator’s built-in offset of about 60 mV divided by the 1.235 reference voltage (Refer to the block diagram). This trip level remains “5% below normal” regardless of the programmed output voltage of the 2951. For example, the error flag trip level is typically 4.75V for a 5V output or 11.4V for a 12V output. The out of regulation condition may be due either to low input voltage, current limiting, or thermal limiting. Figure 1 gives a timing diagram depicting the ERROR signal and the regulator output voltage as the AMS2954 input is ramped up and down. For 5V versions the ERROR signal becomes valid (low) at about 1.3V input. It goes high at about 5V input (the input voltage at which Vout = 4.75 ). Since the AMS2954’s dropout voltage is load dependent (see curve in typical performance characteristics), the input voltage trip point (about 5V) will vary with the load current. The output voltage trip point (approx. 4.75V) does not vary with load. The error comparator has an open-collector output which requires an external pull-up resistor. This resistor may be returned to the output or some other supply voltage depending on system requirements. In determining a value for this resistor, note that the output is rated to sink 400µA, this sink current adds to battery drain in a low battery condition. Suggested values range from 100K to 1MΩ. The resistor is not required if this output is unused. OUTPUT VOLTAGE 4.75V ERROR* 5V INPUT VOLTAGE 1.3V FIGURE 1. ERROR Output Timing *When VIN ≤1.3V the error flag pin becomes a high impedance, and the error flag voltage rises to its pull-up voltage. Using Vout as the pull-up voltage (see Figure 2), rather than an external 5V source, will keep the error flag voltage under 1.2V (typ.) in this condition. The user may wish to drive down the error flag voltage using equal value resistors (10 kΩ suggested), to ensure a lowlevel logic signal during any fault condition, while still allowing a valid high logic level during normal operation. Programming the Output Voltage The AMS2954 may be pin-strapped for the nominal fixed output voltage using its internal voltage divider by tying the output and sense pins together, and also tying the feedback and VTAP pins together. Alternatively, it may be programmed for any output voltage between its 1.235V reference and its 30V maximum rating. As seen in Figure 2, an external pair of resistors is required. The complete equation for the output voltage is: Vout = VREF × (1 + R1/ R2)+ IFBR1 where VREF is the nominal 1.235 reference voltage and IFB is the feedback pin bias current, nominally -20 nA. The minimum recommended load current of 1 µA forces an upper limit of 1.2 MΩ on value of R2, if the regulator must work with no load (a condition often found in CMOS in standby) IFB will produce a 2% typical error in VOUT which may be eliminated at room temperature by trimming R1. For better accuracy, choosing R2 = 100k reduces this error to 0.17% while increasing the resistor program current by 12 µA. Since the AMS2954 typically draws 60 µA at no load with Pin 2 open-circuited, this is a small price to pay. Advanced Monolithic Systems, Inc. www.advanced-monolithic.com Phone (925) 443-0722 Fax (925) 443-0723 AMS2954 APPLICATION HINTS (Continued) IIN +VIN VIN 5V AMS2954 + * 5 ERROR* **SHUTDOWN INPUT 3 1.2 VOUT 1 AMS2954 SD GND 4 LOAD VOUT +VIN ERROR OUPUT 1µF GND 8 100k IL OUT IN R1 FB 7 30V * + .01µ F R2 FIGURE 2. Adjustable Regulator *See Application Hints. Vout = VREF × (1 + R1/ R2) **Drive with TTL- high to shut down. Ground or leave if shutdown feature is not used. Note: Pins 2 and 6 are left open. FIGURE 3. Basic 5V Regulator Figure 3 shows the voltages and currents which are present in a 5V regulator circuit. The formula for calculating the power dissipated in the regulator is also shown in Figure 3. The next parameter which must be calculated is the maximum allowable temperature rise, TR(max). This is calculated using the formula: TR(max) =TJ(max) - TA(max) Where TJ(max) is the maximum allowable junction temperature, and TA(max) is the maximum ambient temperature. Using the calculated values for TR(max) and P(max), the required value for junction to ambient thermal resistance θ(J-A), can be determined: Reducing Output Noise In reference applications it may be an advantageous to reduce the AC noise present at the output. One method is to reduce the regulator bandwidth by increasing the size of the output capacitor. This is the only way that noise can be reduced on the 3 lead AMS2954 but is relatively inefficient, as increasing the capacitor from 1 µF to 220 µF only decreases the noise from 430 µV to 160 µV rms for a 100 kHz bandwidth at 5V output. Noise could also be reduced fourfold by a bypass capacitor across R1, since it reduces the high frequency gain from 4 to unity. Pick CBYPASS ≅ 1 / 2πR1 × 200 Hz or about 0.01 µF. When doing this, the output capacitor must be increased to 3.3 µF to maintain stability. These changes reduce the output noise from 430 µV to 100 µV rms for a 100 kHz bandwidth at 5V output. With the bypass capacitor added, noise no longer scales with output voltage so that improvements are more dramatic at higher output voltages. IG * See external capacitors PTotal = (VIN -5)IL +(VIN)IG 3.3µF 1.23 V VREF IIN = IL +IG θ(J-A) = TR(max) /P(max) If the value obtained is 60°C/W or higher, the regulator may be operated without an external heatsink. If the calculated value is below 60°C/W, an external heatsink is required. To calculate the thermal resistance of this heatsink use the formula: θ(H-A) = θ(J-A) - θ(J-C) - θ(C-H) where: θ(J-C) is the junction-to-case thermal resistance, which is specified as 3°C/W maximum for the AMS2954. θ(C-H) is the case-to-heatsink thermal resistance, which is dependent on the interfacing material (if used). θ(H-A) is the heatsink-to-ambient thermal resistance. It is this specification which defines the effectiveness of the heatsink. The heatsink selected must have a thermal resistance equal or lower than the value of θ(H-A) calculated from the above listed formula. Output Isolation Heatsink Requirements A heatsink might be required when using AMS2954, depending on the maximum power dissipation and maximum ambient temperature of the application. The heatsink must be chosen considering that under all operating condition, the junction temperature must be within the range specified under Absolute Maximum Ratings. To determine if a heatsink is required, the maximum power dissipated by the regulator must be calculated. It is important to consider, that if the regulator is powered from a transformer connected to the AC line, the maximum specified AC input voltage must be used. The regulator output can be left connected to an active voltage source with the regulator input power turned off, as long as the regulator ground pin is connected to ground. If the ground pin is left floating, damage to the regulator can occur if the output is pulled up by an external voltage source. Advanced Monolithic Systems, Inc. www.advanced-monolithic.com Phone (925) 443-0722 Fax (925) 443-0723 AMS2954 TYPICAL APPLICATIONS (Continued) Wide Input Voltage Range Current Limiter +VIN 8 +VIN 5 ERROR OUPUT VOUT 1 ERROR *VOUT ≈ VΙΝ AMS2954 SHUTDOWN 3 SD INPUT GND FB 4 7 *Minimum Input-Output voltage ranges from 40mV to 400mV, depending on load current. Current limit is typically 260 mA Low Drift Current Source +V = 2 IL 5Volt Current Limiter 30V LOAD 5V BUS 8 VIN +VIN VOUT 1 *VOUT ≈ 5V AMS2954 -5.0 VOUT AMS2954 SHUTDOWN 3 SD INPUT 0.1µF GND 4 1µF FB 7 R 1% GND 1µF + *Minimum Input-Output voltage ranges from 40mV to 400mV, depending on load current. Current limit is typically 260 mA 5V Regulator with 2.5V Sleep Function Open Circuit Detector for 4 to 20mA Current Loop +5V +VIN C - MOS GATE *SLEEP INPUT 4.7kΩ 4 20mA *OUTPUT 1 8 47kΩ 470kΩ +VIN 8 ERROR OUPU T VOUT +VIN 5 ERROR SHUTDOWN 3 SD INPUT +VOUT VOUT 1 GND 4 4 7 1% + 2N3906 2 FB 200kΩ 100pF FB 7 1 AMS2954 1N4001 AMS2954 5 3.3µF 100kΩ 1% 100kΩ Advanced Monolithic Systems, Inc. www.advanced-monolithic.com 0.1µF GND 4 1N457 360 MIN. VOLTAGE ≈ 4V Phone (925) 443-0722 Fax (925) 443-0723 AMS2954 TYPICAL APPLICATIONS (Continued) 2 Ampere Low Dropout Regulator CURRENT LIMIT SECTION Regulator with Early Warning and Auxiliary Output +VIN +VIN = VOUT +.5V 8 +VIN 0.05 680 6 470 7 4.7MΩ FB VOUT 7 FB GND 4 ERROR FLAG 5 AMS2954 220 1µF 3.6V NICAD 27 kΩ ERROR SD 20 + GND 4 +VIN 3 5V MEMORY SUPPLY D2 1 AMS2954 #1 5 ERROR +VOUT @ 2A 10kΩ 8 2 SENSE VTAP MJE2955 2N3906 D1 + R1 + 4.7 TANT. 100µF D4 1% VOUT R2 1 EARLY WARNING D3 2.7MΩ Q1 20kΩ 8 +VIN 6 .033 2 SENSE VOUT VTAP 7 330 kΩ MAIN 5V OUTPUT FB AMS2954 #2 5 SD ERROR 3 + RESET µP VDD 1µF GND 4 VOUT = 1.23V(1+R1/R2) For 5V VOUT, use internal resistors. Wire pin 6 to 7 and pin 2 to +VOUTBuss. • Early warning flag on low input voltage • Main output latches off at lower input voltages • Battery backup on auxiliary output Operation: Reg.#1’s VOUT is programmed one diode drop above 5V. It’s error flag becomes active when VIN≤ 5.7V. When VIN drops below 5.3V, the error flag of Reg.#2 becomes active and via Q1 latches the main output off. When VIN again exceeds 5.7V Reg.#1 is back in regulation and the early warning signal rises, unlatching Reg.#2 via D3. 1A Regulator with 1.2V Dropout Latch Off When Error Flag Occurs +VIN UNREGULATE D INPUT 10kΩ 1µF 0.01µF SUPERTEX VP12C 470kΩ 8 IN 6 VTAP SENSE 1Μ Ω FB + 470kΩ AMS2954 0.002µ F R1 220µF 1 RESET VOUT +VIN 1 VOUT ERROR 3 SD OUT GND 4 OUTPUT 5V ± 1% @ 0 TO 1A 2 AMS2954 7 8 5 FB GND 4 + 7 1µF R2 2kΩ IQ ≅ 400µA Advanced Monolithic Systems, Inc. www.advanced-monolithic.com Phone (925) 443-0722 Fax (925) 443-0723 AMS2954 PACKAGE DIMENSIONS inches (millimeters) unless otherwise noted. 3 LEAD TO-220 PLASTIC PACKAGE (T) 0.147-0.155 (3.734-3.937) DIA 0.390-0.415 (9.906-10.541) 0.165-0.180 (4.191-4.572) 0.045-0.055 (1.143-1.397) 0.230-0.270 (5.842-6.858) 0.570-0.620 (14.478-15.748) 0.460-0.500 (11.684-12.700) 0.330-0.370 (8.382-9.398) 0.980-1.070 (24.892-27.178) 0.218-0.252 (5.537-6.401) 0.520-0.570 (13.208-14.478) 0.090-0.110 (2.286-2.794) 0.028-0.038 (0.711-0.965) 0.050 (1.270) TYP 0.013-0.023 (0.330-0.584) 0.095-0.115 (2.413-2.921) T (TO-220) AMS DRW# 042193 3 LEAD TO-263 PLASTIC DD (M) Advanced Monolithic Systems, Inc. www.advanced-monolithic.com Phone (925) 443-0722 Fax (925) 443-0723 AMS2954 PACKAGE DIMENSIONS inches (millimeters) unless otherwise noted (Continued). TO-252 PLASTIC PACKAGE (D) 0.020-0.030 (0.508-0.762) 0.258-0.262 (6.553-6.654) 0.208-0.212 (5.283-5.384) 0.020-0.030 (0.508-0.762) 0.085-0.095 (2.159-2.413) 0.033-0.037 (0.838-0.939) 0.030-0.034 (0.762-0.863) 0.038-0.042 (0.965-1.066) 7.0° 0.023-0.027 (0.584-0.685) 45.0° 0.175-0.180 (4.191-4.445) 0.235-0.245 (5.969-6.223) 0.057-0.067 (0.144-0.170) DIA 0.025 (0.635) TYP 0.038 (0.965) TYP 0.099-0.103 (2.514-2.615) 0.088-0.092 (2.235-2.336) 0.030 (0.762) TYP 0.018-0.022 (0.451-0.558) 0.038-0.042 (0.965-1.066) 0.024±0.002 (0.610±0.0508) D (D3) AMS DRW# 042891 3 LEAD SOT-223 PLASTIC PACKAGE 0.248-0.264 (6.30-6.71) 0.116-0.124 (2.95-3.15) 0.264-0.287 (6.71-7.29) 0.130-0.146 (3.30-3.71) 0.033-0.041 (0.84-1.04) 0.090 (2.29) NOM 10°-16° 10° MAX 0.071 (1.80) MAX 0.010-0.014 (0.25-0.36) 10°-16° 0.012 Advanced Monolithic Systems, Inc. 0.025-0.033 www.advanced-monolithic.com (0.31) (0.64-0.84) MIN 0.181 (4.60) NOM 0.025-0.033 Phone (925) 443-0722 (0.64-0.84) Fax (925) 443-0723 (SOT-223 ) AMS DRW# 042292 AMS2954 PACKAGE DIMENSIONS inches (millimeters) unless otherwise noted (Continued). 8 LEAD SOIC PLASTIC PACKAGE (S) 0.189-0.197* (4.801-5.004) 8 7 6 5 0.228-0.244 (5.791-6.197) 0.150-0.157** (3.810-3.988) 1 2 3 4 0.010-0.020 x 45° (0.254-0.508) 0.053-0.069 (1.346-1.752) 0.004-0.010 (0.101-0.254) 0.014-0.019 (0.355-0.483) 0.008-0.010 (0.203-0.254) 0.050 (1.270) TYP 0°-8° TYP 0.016-0.050 (0.406-1.270) S (SO-8 ) AMS DRW# 042293 *DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE 8 LEAD PLASTIC DIP PACKAGE (P) 0.400* (10.160) MAX 8 7 6 5 1 2 3 4 0.255±0.015* (6.477±0.381) 0.045-0.065 (1.143-1.651) 0.300-0.325 (7.620-8.255) 0.130±0.005 (3.302±0.127) 0.065 (1.651) TYP 0.005 (0.127) MIN 0.100±0.010 (2.540±0.254) 0.125 (3.175) MIN 0.009-0.015 (0.229-0.381) 0.015 (0.380) MIN 0.018±0.003 (0.457±0.076) 0.325 +0.025 -0.015 (8.255 +0.635 ) -0.381 P (8L PDIP ) AMS DRW# 042294 *DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTUSIONS. MOLD FLASH OR PROTUSIONS SHALL NOT EXCEED 0.010" (0.254mm) Advanced Monolithic Systems, Inc. www.advanced-monolithic.com Phone (925) 443-0722 Fax (925) 443-0723