AMIS-710207-A4: 200dpi CIS Module Data Sheet 1.0 General Description The AMIS-710207-A4 (PI207MC-A4) contact image sensor (CIS) module uses MOS image sensor technology for high-speed performance and high sensitivity. The AMIS-710207-A4 is suitable for scanning A4 size (216mm) documents with 8 dots per millimeter (dpm) resolution. Applications include fax machines, game systems, a variety of mark readers, and other automation equipment requiring document scanners. 2.0 Key Features • • • • • • • • Light source, lens and sensor are integrated into a single module 8dpm resolution, 216mm scanning length Dual LED light source, IR and Red, with a line scan time to 347µsec @ 5MHz Wide dynamic range Analog output Compact size ≅ 14.5mm x 19.5mm x 232mm Low power Light weight 3.0 Functional Description The AMIS-710207-A4 imaging array consists of 27 AMIS-720233 (PI3033B) sensors, produced by AMIS, that are cascaded to provide 1728 photo-detectors with their associated multiplex switches and a digital shift register that controls its sequential readout. Mounted in the module is a one-to-one graded indexed micro lens array that focuses on the image of the scanned documents, then transfers it onto the sensors. The on-board amplifier processes the video signal to produce a sequential stream of video at the output pin of the AMIS-710207-A4 module. Illumination is accomplished by means of integrated LED sources; Red (660nm) and IR (880nm). All components are housed in a small plastic housing, which has a cover glass that acts as the focal point for the object being scanned. In addition, it protects the imaging array, micro lens assembly and LED light source from dust. Inputs and outputs (I/O) to and from the module are by a 10-pin connector, JAE 1L-Z-10P-S125L3-E, located on one end of the module. For the Pin 1 location, see Figure 4, overall view of the module house. A cross section of the AMIS-710207-A4 module is shown in Figure 1 and a block diagram in Figure 2. AMI Semiconductor – May 06, M-20494-001 www.amis.com 1 AMIS-710207-A4: 200dpi CIS Module Figure 1: AMIS-710207-A4 Cross Section Figure 2: AMIS-710207-A4 Module Block Diagram AMI Semiconductor – May 06, M-20494-001 www.amis.com 2 Data Sheet AMIS-710207-A4: 200dpi CIS Module Data Sheet 4.0 Connector Pin Out Designation Connector is JAE part number 1L-Z-S125L3-E. Table 1: Pin Out Configuration Pin Number Symbol 1 VOUT 2 GND 3 Vdd (+5V) 4 Vn (-5V to -12V) 5 GLED RED 6 SP 7 GND 8 CP 9 GLED IR 10 VLED Names and Functions Analog video output Ground; 0V Positive power supply Negative power supply Ground for the Red light source; 0V Shift register start pulse Ground; 0V Sampling clock pulse Ground for the IR light source; 0V Supply for the light source 5.0 Maximum Ratings Table 2: Maximum Ratings Parameter Power supply voltage Symbols Vdd Maximum Rating 7 Units V Input clock pulse (high level) Idd Vn In VLED IR VLED RED ILED IR ILED RED Vih 80 -15 7 5.5 5.5 500 600 Vdd mA V mA V V mA mA V Input clock pulse (low level) Vil -0.5 V Note: These are the maximum ratings and are not to be used in a prolonged condition. 6.0 Operating Environment Table 3: Operating Environment Parameter Operating temperature Operating humidity Storage temperature Storage humidity Symbol Top Hop Tstg Hstg AMI Semiconductor – May 06, M-20494-001 www.amis.com Range 0 to +50 +10 to +85 -25 to +75 +5 to +95 Units ° C % ° C % 3 AMIS-710207-A4: 200dpi CIS Module Data Sheet 7.0 Electro-Optical Characteristics The tabled values are measured at 25°C. Table 4: Electro-Optical characteristics at 25°C Parameter Symbol Number of photo detectors Pixel-to-pixel spacing (1) Line scanning rate Tint (2) Clock frequency fclk (3) Bright output voltage Vpavg (4) Bright output non-uniformity Up (5) Adjacent pixel non-uniformity Uadj (6) Dark non-uniformity Ud (6) Dark output voltage Vd (7) Modulation transfer function MTF Notes: 1. 2. 3. 4. 5. 6. Typical 1728 125 347 5.0 +0.2/-0.1 1.1 <|+/-30| <25 <75 <200 >40 Units Elements µm µsec MHz Volts % % mV mV % Note @ 5.0MHz clock frequency Tint is the line scanning rate or integration time. Tint is determined by the interval of two start pulses, SP. The integration time of 347µsec is set at the factory. For additional comments, see Note (1) under Table 5. fclk: main clock frequency. Vpavg = ∑ Vp(n)/1728. Up = [(Vpmax - Vpavg) / Vpavg] x 100% or [(Vpavg - Vpmin) / Vpavg] x 100%, where Vpmax = maximum pixel amplitude in the line scan and Vpmin = minimum pixel amplitude in the line scan. Upadj = MAX[ | (Vp(n) - Vp(n+l) | / Vp(n)) x 100%. Upadj is the non-uniformity in percent between adjacent pixels, where Vp(n) is the nth pixel in the line scan. Ud = Vdmax – Vdmin. Vd = the average dark output level. Vdmin is the minimum output on a black document (LED is turned off). Vdmax: maximum output voltage of black document (LED is turned off). MTF = [(Vmax - Vmin) / (Vmax + Vmin)] x 100 [%]. Vmax: maximum output voltage at 50lp/in and Vmin: minimum output voltage at 50lp/in, where lp / in is the line pairs per inch. AMI Semiconductor – May 06, M-20494-001 www.amis.com 4 AMIS-710207-A4: 200dpi CIS Module Data Sheet 8.0 Recommended Operating Conditions The tabled values are measured at 25°C. Table 5: Recommended Operating Conditions at 25°C Parameter Symbol Power supply Vdd Vn. VLED IR VLED RED ILED IR ILED RED Idd Ivn Input voltage at digital high Vih Input voltage at digital low Vil (1) Clock frequency fclk Clock pulse high duty cycle Clock pulse high duration (1) Integration time Tint Operating temperature Top Min. 4.5 -4.5 4.5 4.5 200 250 55 4.0 Vdd-1.0 0 Mean 5.0 -5 5 5 300 350 60 5.0 Vdd-.5 25 45.5 316 25 Max. 5.5 -12 5.5 5.5 500 600 70 5.5 Vdd 0.8 5.5 10000 50 Units V V V ma ma ma ma V V MHz % ns µs ° C Note: 1. Electrically, including the image sensors, the circuits will operate above 5.5MHz with tint at 316µs. However, the light power is fixed, so with the shorter integration time, the exposure is reduced. This reduction limits the specification call out to integration time of 0.347ms at 5.0MHz for 1.0V output. 9.0 Timing Characteristics The timing characteristics for the I/O clocks are shown in Figure 3. See the timing symbol definitions in Table 6. The listed values are measured at ~25oC. Figure 3: Timing Diagram AMI Semiconductor – May 06, M-20494-001 www.amis.com 5 AMIS-710207-A4: 200dpi CIS Module Table 6: Timing Symbol Definitions for Figure 3 Parameters Clock cycle time Clock pulse width Clock duty cycle Prohibit crossing time of Start Pulse Data setup time Data hold time Signal delay time Signal settling time Symbol to tw tprh tds tdh tdl tsh Min. 0.333 82 25 15 20 20 50 120 Typ. Data Sheet Max. 5.8 75 10.0 AMIS-710207-A4 Module and Its Mechanical Dimensions This is an overview drawing of the module. A full size drawing is available upon request. Figure 4: Overall View of the Module Housing AMI Semiconductor – May 06, M-20494-001 www.amis.com 6 Units µs ns % ns ns ns ns ns AMIS-710207-A4: 200dpi CIS Module Data Sheet 11.0 Company or Product Inquiries For more information about AMI Semiconductor, our technology and our product, visit our Web site at: http://www.amis.com North America Tel: +1.208.233.4690 Fax: +1.208.234.6795 Europe Tel: +32 (0) 55.33.22.11 Fax: +32 (0) 55.31.81.12 Production Technical Data - The information contained in this document applies to a product in production. AMI Semiconductor and its subsidiaries (“AMIS”) have made every effort to ensure that the information is accurate and reliable. However, the characteristics and specifications of the product are subject to change without notice and the information is provided “AS IS” without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify that data being relied on is the most current and complete. AMIS reserves the right to discontinue production and change specifications and prices at any time and without notice. Products sold by AMIS are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. AMIS makes no other warranty, express or implied, and disclaims the warranties of noninfringement, merchantability, or fitness for a particular purpose. AMI Semiconductor's products are intended for use in ordinary commercial applications. These products are not designed, authorized, or warranted to be suitable for use in life-support systems or other critical applications where malfunction may cause personal injury. Inclusion of AMIS products in such applications is understood to be fully at the customer’s risk. Applications requiring extended temperature range, operation in unusual environmental conditions, or high reliability, such as military or medical life-support, are specifically not recommended without additional processing by AMIS for such applications. Copyright © 2006 AMI Semiconductor, Inc. AMI Semiconductor – May 06, M-20494-001 www.amis.com 7