PRODUCT DATASHEET AAT3783 BatteryManagerTM 1-A Linear Li-Ion/Polymer Battery Charger with 28V Over-Voltage Protection General Description Features The AAT3783 BatteryManager™ is a single-cell LithiumIon (Li-Ion)/Li-Polymer battery charger IC, designed to operate from USB ports, AC adapter inputs, or from a charger adapter up to an input voltage of 6.5V. For increased safety, the AAT3783 also includes over-voltage input protection (OVP) up to 28V. • USB or AC Adapter System Power Charger • Programmable from 100mA to 1A Max • 4.0V ~ 7.5V Input Voltage Range ▪ Over-Voltage Input Protection up to 28V • High Level of Integration with Internal: ▪ Charging Device ▪ Reverse Blocking Diode ▪ Current Sensing • Digital Thermal Regulation • Charge Current Programming (ISET) • Charge Termination Current Programming (TERM) • Charge Timer (CT) • Battery Temperature Sensing (TS) • TS Pin Open Detection • Automatic Recharge Sequencing • No Trickle Charge Option Available • Full Battery Charge Auto Turn Off / Sleep State / Charge Termination • Automatic Trickle Charge for Battery Pre-conditioning • Battery Over-Voltage and Over-Current Protection • Emergency Thermal Protection • Power On Reset • 16-pin 3x4mm TDFN Package The AAT3783 precisely regulates battery charge voltage and current for 4.2V Li-Ion/Polymer battery cells through an extremely low RDS(ON) switch. When charged from an adapter or a USB port, the battery charging current can be set by an external resistor up to 1A. In the case of an over-voltage condition in excess of 6.5V, a series switch opens preventing damage to the battery and charging circuitry. With the addition of an external resistor the OVP trip point can be programmed to a level other than the factory set value of 6.5V. In the case of an OVP condition a fault flag is activated. Battery charge state is continuously monitored for fault conditions. In the event of an over-current, battery overvoltage, short-circuit or over-temperature failure, the device will automatically shut down, thus protecting the charging device, control system and the battery under charge. A status monitor output pin is provided to indicate the battery charge status by directly driving an external LED. An open-drain power-source detection output (ADPP) is provided to report the power supply status. Applications • • • • • • The AAT3783 comes in a thermally enhanced, spacesaving, Pb-free 16-pin 3x4 mm TDFN package and is specified for operation over the -40°C to +85°C temperature range. Bluetooth™ Headsets, Headphones, Accessories Digital Still Cameras Mobile Phones MP3 Players Personal Data Assistants (PDAs) Other Li-Ion/Polymer Battery Powered Devices Typical Application VIN IN BATS IN BAT FLT BATT+ 10μF AAT3783 BATT- OVP INCHR TEMP TS 2.2μF CT Battery Pack STAT TERM ADPP 3783.2008.08.1.2 Enable Charging ENCHR Enable OVP ENOVP ISET RSET RTERM CT GND www.analogictech.com 1 PRODUCT DATASHEET AAT3783 BatteryManagerTM 1-A Linear Li-Ion/Polymer Battery Charger with 28V Over-Voltage Protection Pin Descriptions Pin Number Name Type 1 INCHR I/O 2 BATS I 3 4 5 BAT TS ENOVP O I/O I 6 OVP I 7 8 9 10 11 FLT STAT ADPP CT ENCHR O O O I I 12 TERM I 13 14 15, 16 GND ISET IN I/O I I Function Internal connection between the output of the OVP stage and the input of the battery charger. Decouple with 2.2μF capacitor. Battery sense pin. Connect directly to the battery's + terminal. If not used, BATS must be connected to BAT. Connect to Lithium-Ion battery. Battery temperature sense pin. Active low enable for OVP stage. Over-voltage protection threshold pin. Leave open for the default 6.5V setting; connect to a resistor to adjust the OVP setting (see Application Information). Over-voltage fault flag, open drain. Charge status pin, open drain. Input power-good (USB port/adapter present indicator) pin, open-drain. Charge timer programming input pin (no timer if grounded). Active high enable pin (with internal pull-down) for charging circuitry. Charge termination current programming input pin (internal default 10% termination current if TERM is open). Connect to power ground. Charge current programming input pin. Input from USB port/ adapter connector. Pin Configuration TDFN34-16 (Top View) INCHR BATS BAT TS ENOVP OVP FLT STAT 2 16 1 EP1 2 15 3 14 4 5 13 EP2 12 6 11 7 10 8 9 IN IN ISET GND TERM ENCHR CT ADPP www.analogictech.com 3783.2008.08.1.2 PRODUCT DATASHEET AAT3783 BatteryManagerTM 1-A Linear Li-Ion/Polymer Battery Charger with 28V Over-Voltage Protection Absolute Maximum Ratings1 Symbol VIN VINCHR VFLT VN TJ TLEAD Description IN continuous Charger IN continuous Fault flag continuous BAT, STAT, ADPP, EN, ISET, TS, ENOVP, OVP Operating Junction Temperature Range Maximum Soldering Temperature (at Leads) Value Units 30 -0.3 to 7.5 -0.3 to +30 -0.3 to VINCHR + 0.3 -40 to 150 300 V V V V °C °C Value Units 50 2 °C/W W Thermal Information2 Symbol θJA PD Description Maximum Thermal Resistance (TDFN 3x4) Maximum Power Dissipation 1. Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum Rating should be applied at any one time. 2. Mounted on a FR4 board. 3783.2008.08.1.2 www.analogictech.com 3 PRODUCT DATASHEET AAT3783 BatteryManagerTM 1-A Linear Li-Ion/Polymer Battery Charger with 28V Over-Voltage Protection Electrical Characteristics1 VIN = 5V, TA = -40°C to +85°C; unless otherwise noted, typical values are at TA = 25°C. Symbol Description Conditions Operation VIN_MAX Input Over-Voltage Protection Range VIN Normal Operating Input Voltage Range Over-Voltage Protection Under-Voltage Lockout Threshold VUVLO UVLO Hysteresis IQ ISD(OFF) Rising Edge Shutdown Supply Current Rising Edge Charge Termination Threshold Current Battery Charging Device RDS(ON) Total ON Resistance (IN to BAT) V V V mV 30 50 μA 4 8 μA V 3 VIN > VUVLO Charge Current = 100mA, ENOVP = 0V, ENCHG = VIN VBAT = 4.25V, ENOVP = ENCHG = 0V2 VBAT = 4V, ENOVP = VIN 4.158 (Option available for no trickle charge) 4 V mV 60 150 mV 0.5 1 mA 0.4 0.4 1 2 μA μA 4.20 0.5 2.6 4.242 V % V 2.5 2.7 VBAT_EOC 0.1 Current Regulation ICC_RANGE Charge Current Programmable Range ICH_CC Constant-Current Mode Charge Current VISET ISET Pin Voltage KISET Charge Current Set Factor: ICH_CC/IISET VTERM TERM Pin Voltage ICH_TERM 28 7.5 6.5 Battery Recharge Voltage Threshold Trickle Charge Current Units 150 Operating Current ICH_TRK Max 3 60 VIN = 5V, ENOVP = 0V, IOUT = 0, ENCHG = 0V ENOVP = VIN = 5.5V, VOUT = 0V, ENCHG = 0V Rising Edge, OVP = Not Connected Operating Quiescent Current ISHUTDOWN Shutdown Mode Current IBAT Leakage Current from BAT Pin Voltage Regulation VBAT_EOC Output Charge Voltage Regulation ΔVCH/VCH Output Charge Voltage Tolerance VMIN Preconditioning Voltage Threshold VRCH Typ 4.0 VOVPT Over-Voltage Protection Trip Voltage Battery Charger Under-Voltage Lockout Threshold VUVLO UVLO Hysteresis Adapter Present Indicator Threshold VADPP_TH Voltage, VIN - VBAT IOP Min VBAT = 3.6V 100 -10 V 1000 10 2 800 0.2 Constant Current Mode, VBAT = 3.6V RTERM = 13.3kΩ 5 10 15 TERM Pin Open 5 10 15 RTERM = 13.3 kΩ, ICH_CC ≥ 800mA 8 10 12 VIN = 5V, IOUT = 1A 550 mA % V V % ICH_CC % ICH_CC % mΩ 1. The AAT3783 is guaranteed to meet performance specifications over the -40°C to +85°C operating temperature range and is assured by design, characterization and correlation with statistical process controls. 2. Current into charge. 4 www.analogictech.com 3783.2008.08.1.2 PRODUCT DATASHEET AAT3783 BatteryManagerTM 1-A Linear Li-Ion/Polymer Battery Charger with 28V Over-Voltage Protection Electrical Characteristics1 VIN = 5V, TA = -40°C to +85°C; unless otherwise noted, typical values are at TA = 25°C. Symbol Description Conditions Logic Control Input High Threshold VEN(H) VEN(L) Input Low Threshold VSTAT Output Low Voltage ISTAT STAT Pin Current Sink Capability VADDP Output Low Voltage ADPP Pin Current Sink Capability IADPP VFLT Output Low Voltage IFLT FLT Pin Current Sink Capability TBLK_FLT FLT Blanking Time TD_FLT FLT Assertion Delay Time from Over-Voltage TRESP_OV Over-Voltage Response Time TOVPON OVP Turn-On Delay Time TOVPR OVP Turn-On Rise Time TOVPOFF OVP Turn-Off Delay Time Min Typ Max 1.6 STAT Pin Sinks 4mA ADPP Pin Sinks 4mA FLT Pin Sinks 1mA From De-assertion of OV From Assertion of OV VIN Rise to 7V from 5V in 1ns Charging current = 500mA, CINCHR = 1μF Charging current = 500mA, CINCHR = 1μF Charging current = 500mA, CINCHR = 1μF 5 10 1 1 0.4 0.4 8 0.4 8 0.4 5 15 Units V V V mA V mA V mA ms μs μs 10 ms 1 ms 6 μs 4.4 V 105 3 25 3 75 331 25 2.39 25 115 85 100 140 15 % ICH_CC Hour Minute Hour μA Battery Protection VBOVP Battery Over-Voltage Protection Threshold IBOCP TC TK TV ITS Battery Over-Current Protection Threshold Trickle Plus Constant Current Mode Timeout Trickle Timeout Constant Voltage Mode Time Out Current Source from TS Pin TS1 TS Hot Temperature Fault TS2 TS Cold Temperature Fault TLOOP_IN TLOOP_OUT TREG TSHDN CCT = 100nF, VIN = 5V CCT = 100nF, VIN = 5V CCT = 100nF, VIN = 5V Threshold Hysteresis Threshold Hysteresis Thermal Loop Entering Threshold Thermal Loop Exiting Threshold Thermal Loop Regulation Chip Thermal Shutdown Temperature Threshold Hysteresis 69 316 2.30 81 346 2.48 mV V mV ºC ºC ºC ºC 1. The AAT3783 is guaranteed to meet performance specifications over the -40°C to +85°C operating temperature range and is assured by design, characterization and correlation with statistical process controls. 3783.2008.08.1.2 www.analogictech.com 5 PRODUCT DATASHEET AAT3783 BatteryManagerTM 1-A Linear Li-Ion/Polymer Battery Charger with 28V Over-Voltage Protection Constant Charging Current vs. Set Resistor Values Battery Charging Current vs. Battery Voltage 1200 10000 Charging Current (mA) Constant Charging Current (mA) Typical Characteristics 1000 100 10 10 100 RSET = 2kΩ 800 600 RSET = 3.24kΩ 400 RSET = 8.06kΩ 200 0 2.5 1 1 RSET = 1.62kΩ 1000 1000 2.7 2.9 3.1 RSET (mA) 3.3 3.5 3.7 3.9 4.1 4.3 4.5 Battery Voltage (V) End of Charge Regulation Tolerance vs. Input Voltage End of Charge Voltage vs. Temperature 0.15 4.23 0.1 4.22 0.05 4.21 VEOC (%) ΔVBAT_EOC/VBAT_EOC (%) (VBAT_EOC = 4.2V) 0 -0.05 -0.1 4.20 4.19 4.18 -0.15 4.5 4.17 5 5.5 6 6.5 7 -40 7.5 -15 10 Input Voltage (V) 85 Preconditioning Charge Current vs. Input Voltage 4.16 140 4.14 120 ICH_TRK (mA) Recharge Voltage (%) 60 Temperature (°C) Battery Recharge Voltage Threshold vs. Temperature 4.12 4.1 4.08 4.06 100 RSET = 1.62kΩ 80 60 40 RSET = 2kΩ RSET = 3.24kΩ 20 RSET = 8.06kΩ 4.04 -40 0 -15 10 35 60 85 Temperature (°C) 6 35 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 Input Voltage (V) www.analogictech.com 3783.2008.08.1.2 PRODUCT DATASHEET AAT3783 BatteryManagerTM 1-A Linear Li-Ion/Polymer Battery Charger with 28V Over-Voltage Protection Typical Characteristics Preconditioning Charge Current vs. Temperature Preconditioning Voltage Threshold vs. Temperature 23 2.66 22 2.64 21 2.62 VMIN (V) Preconditioning Charge Current (mA) (RSET = 8.06kΩ; ICH_CC = 200mA) 20 19 2.60 2.58 2.56 18 2.54 17 -40 -15 10 35 60 -40 85 -15 10 Temperature (°C) 85 Total Resistance vs. Input Voltage (RSET = 1.62kΩ Ω) (IN to BAT) 1200 800 VBAT = 3.3V 750 1100 VBAT = 3.6V 700 RDS(ON) (mΩ Ω) Constant Charging Current (mA) 60 Temperature (°C) Constant Charging Current vs. Input Voltage 1000 900 VBAT = 3.9V 85°C 650 600 25°C 550 500 800 -40°C VBAT = 4.1V 450 700 4 4.5 5 5.5 6 6.5 7 7.5 400 3.6 3.8 4 Input Voltage (V) 335 333 331 329 327 10 35 60 85 Temperature Sense Threshold Voltage (TS2) (mV) 337 -15 Temperature (°C) 3783.2008.08.1.2 4.4 4.6 4.8 5 Temperature Sense Too Cold Threshold vs. Temperature 339 325 -40 4.2 Input Voltage (V) Temperature Sense Too Hot Threshold vs. Temperature Temperature Sense Threshold Voltage (TS1) (mV) 35 2.400 2.395 2.390 2.385 2.380 2.375 -40 -15 10 35 60 85 Temperature (°C) www.analogictech.com 7 PRODUCT DATASHEET AAT3783 BatteryManagerTM 1-A Linear Li-Ion/Polymer Battery Charger with 28V Over-Voltage Protection Typical Characteristics Temperature Sense Output Current vs. Temperature CT Pin Capacitance vs. Counter Timeout 78 1.0 0.9 Capacitance (µF) ITS (mV) 76 74 72 70 0.8 0.7 Preconditioning Timeout 0.6 0.5 0.4 0.3 Preconditioning + Constant Current Timeout or Constant Voltage Timeout 0.2 0.1 68 0.0 -40 -15 10 35 60 0 85 0.5 1 1.5 2 Temperature (°C) 2.5 3 3.5 4 4.5 5 Time (h) Operating Current vs. ISET Resistor Termination Current to Constant Current Ratio vs. Termination Resistance 1.6 50 1.4 ICH_TERM/ICH_CC (%) Constant current mode IOP (mA) 1.2 1.0 0.8 0.6 0.4 0.2 40 30 20 10 Preconditioning mode 0.0 0 1 10 100 0 1000 10 20 RSET (kΩ) 1.4 1.4 1.2 1.2 VEN(H) (V) VEN(L) (V) 1.6 25°C 0.8 85°C 0.6 60 -40°C 1.0 0.8 25°C 85°C 0.6 0.4 0.4 4 4.5 5 5.5 6 6.5 7 7.5 Input Voltage (V) 8 50 Input High Threshold vs. Input Voltage 1.6 -40°C 40 ITERM Resistance (kΩ) Input Low Threshold vs. Input Voltage 1.0 30 4 4.5 5 5.5 6 6.5 7 7.5 Input Voltage (V) www.analogictech.com 3783.2008.08.1.2 PRODUCT DATASHEET AAT3783 BatteryManagerTM 1-A Linear Li-Ion/Polymer Battery Charger with 28V Over-Voltage Protection Typical Characteristics OVP Trip Point vs. Temperature FLT Blanking Time 12 0.05 6 4 6 2 4 0 2 -2 0 -4 VOVPTRIP Error (%) 8 FLT Voltage (V) Input Voltage (V) 10 0.00 -0.05 -0.10 -0.15 -0.20 -40 10 35 60 85 Temperature (°C) Time (2ms/div) 3783.2008.08.1.2 -15 www.analogictech.com 9 PRODUCT DATASHEET AAT3783 BatteryManagerTM 1-A Linear Li-Ion/Polymer Battery Charger with 28V Over-Voltage Protection Functional Block Diagram INCHR IN Reverse Blocking Over-Current Protection IN BAT OVP BAT S CV/ PreCharge Current Compare ENOVP OVP Sense and Control Constant Current FLT ADPP Charge Control UVLO Over Temp. Protect Power Detection Thermal Loop Charge Status ISET STAT TERM CT ENCHR TS GND Functional Description Battery Preconditioning The AAT3783 is a high performance battery charger designed to charge single cell Lithium-Ion or Polymer batteries with up to 1000mA of current from an external power source. It is a stand-alone charging solution, with just one external component required (two more for options) for complete functionality. Also included is input voltage protection (OVP) to up to +28V. OVP consists of a low resistance P-channel MOSFET in series with the charge control MOSFET, and also consists of under-voltage lockout protection, over-voltage monitor, and fast shut-down circuitry with a fault output flag. Battery charging commences only after the AAT3783 checks several conditions in order to maintain a safe charging environment. The input supply must be above the minimum operating voltage (VUVLO) and the enable pin must be high. When the battery is connected to the BAT pin, the AAT3783 checks the condition of the battery and determines which charging mode to apply. If the battery voltage is below the preconditioning voltage threshold, VMIN, then the AAT3783 begins preconditioning the battery cell (trickle charging) by charging at 10% of the programmed constant current. For example, if the programmed current is 500mA, then the preconditioning mode (trickle charge) current is 50mA. Battery cell preconditioning (trickle charging) is a safety precaution for deeply discharged cells and will also reduce the power dissipation in the internal series pass MOSFET when the input-output voltage differential is at the greatest potential. Battery Charging Operation Figure 1 illustrates the entire battery charging profile or operation, which consists of three phases: 1. Preconditioning (Trickle) Charge 2. Constant Current Charge 3. Constant Voltage Charge 10 www.analogictech.com 3783.2008.08.1.2 PRODUCT DATASHEET AAT3783 BatteryManagerTM 1-A Linear Li-Ion/Polymer Battery Charger with 28V Over-Voltage Protection Preconditioning Trickle Charge Phase Constant Current Charge Phase Constant Voltage Charge Phase Charge Complete Voltage I = Max CC Regulated Current Constant Current Mode Voltage Threshold Trickle Charge and Termination Threshold I = CC / 10 Figure 1: Current vs. Voltage Profile during Charging Phases. Constant Current Charging Thermal Considerations Battery cell preconditioning continues until the battery voltage reaches the preconditioning voltage threshold, VMIN. At this point, the AAT3783 begins constant current charging. The current level for this mode is programmed using a single resistor from the ISET pin to ground. The programmed current can be set at a minimum 100mA up to a maximum of 1A. The actual maximum charging current is a function of the charge adapter input voltage, the battery charge state at the moment of charge, the ambient temperature, and the thermal impedance of the package. The maximum programmable current may not be achievable under all operating parameters. Over-Voltage Protection Constant Voltage Charging Constant current charging will continue until such time that the battery voltage reaches the voltage regulation point, VBAT_EOC. When the battery voltage reaches VBAT_EOC, the AAT3783 will transition to constant voltage mode. The regulation voltage is factory programmed to a nominal 4.2V and will continue charging until the charge termination current is reached. Charge Status Output The AAT3783 provides battery charge status via a status pin. This pin is internally connected to an N-channel open-drain MOSFET, which can be used drive an external LED. The status pin can indicate the following conditions: Event Description STATUS No battery charging activity Battery charging via adapter or USB port Charging completed Table 1: LED Status Indicator. 3783.2008.08.1.2 OFF ON OFF In normal operation, a P-channel MOSFET acts as a slew-rate controlled load switch, connecting and disconnecting the power supply from IN to INCHR. A low resistance MOSFET is used to minimize the voltage drop between the voltage source and the charger and to reduce the power dissipation. When the voltage on the input exceeds the over-voltage trip point (internally set by the factory or externally programmed by a resistor connected to the OVP pin), the device immediately turns off the internal P-channel FET which disconnects the charger from the abnormal input voltage, therefore preventing any damage to the charger. Simultaneously, the fault flag is raise, alerting the system. If an over-voltage condition is applied at the time of the device enable, then the switch will remain OFF. OVP Under-Voltage Lockout (UVLO) The AAT3783 OVP circuitry has a fixed 3V under-voltage lockout level (UVLO). When the input voltage is less than the UVLO level, the MOSFET is turned off. 100mV of hysteresis is included to ensure circuit stability. www.analogictech.com 11 PRODUCT DATASHEET AAT3783 BatteryManagerTM 1-A Linear Li-Ion/Polymer Battery Charger with 28V Over-Voltage Protection Over-Current Protection Enable / Disable The AAT3783 over-current protection provides faultcondition protection that limits the charge current to approximately 1.6A under all conditions, even if the ISET pin gets shorted to ground. The AAT3783 provides an enable function to control the OVP stage and charger on and off independently. FLT Blanking Time The FLT output is an active-low open-drain fault (OV) reporting output. A pull-up resistor should be connected from FLT to the logic I/O voltage of the host system. FLT will be asserted immediately an over-voltage fault occurs (only about a 1μs inherited internal circuit delay). A 10ms blanking is applied to the FLT signal prior to deassertion. 12 ENOVP is an active-low enable input. ENOVP is driven low, connected to ground, or left floating for normal device operation. Taking ENOVP high turns off the MOSFET of the OVP stage. In the case of an over-voltage or UVLO condition, toggling ENOVP will not override the fault condition and the switch will remain off. OVP Turn-On Delay Time On initial power-up, if VIN < UVLO or if VOVP > 6.5V the PMOS is held off. If UVLO < VIN, VOVP < 6.5V, and ENOVP is low, the device enters startup after a 10ms internal delay. www.analogictech.com 3783.2008.08.1.2 PRODUCT DATASHEET AAT3783 BatteryManagerTM 1-A Linear Li-Ion/Polymer Battery Charger with 28V Over-Voltage Protection System Operation Flow Chart ADP Voltage Power Input S Voltage ADP > VADPP VIN>VUVLO Power On Sleep Sleep Reset Mode Mode No Yes Enable Power Select OVP? No ENOVP = Yes OVP Condition Monitoring VIN > 6.5V? No Shut Disconnect Input ShutDown Down fromMode charger Mode ENCHR = Yes Fault Fault Condition Monitoring Power Select OV, OT, VTS1<TS<VTS2 Yes Shutdown Shut ShutDown Down Mode Mode Mode Expire No Charger Shut Down ShutTimer Down Control Mode Mode Preconditioning Test V BAT VMIN>V >V MIN Yes Preconditioning Shut ShutDown Down Enable (Trickle Charge) Mode Mode BAT No No Recharge Test VV RCH BAT RCH> V BAT Yes Current Phase Test VIN>VBAT_EOC Yes Constant Shut Down ShutCurrent Down Charge Mode Mode Mode VCH >VBAT No Device DeviceTemp. Temp. No Monitor Monitor >110 C TJ >115 Yes Thermal Loop Shut Down Shut Down Current Reduction Mode In C.C. Mode Mode Voltage Phase Test IBAT>ITERM IBAT> MIN I Yes Constant Shut Down ShutVoltage Down Charge Mode Mode Mode No Charge Charge Completed Completed 3783.2008.08.1.2 www.analogictech.com 13 PRODUCT DATASHEET AAT3783 BatteryManagerTM 1-A Linear Li-Ion/Polymer Battery Charger with 28V Over-Voltage Protection Application Information Programming the Over-Voltage Protection Trip Point The default over-voltage protection trip point of the AAT3783 is set to 6.5V by the factory. However, the over-voltage protection trip point can be programmed from 3.8V to 7.5V by the user with one external resistor, either R5 or R6. The placement of R5 is between IN and OVP. The placement of R6 is between OVP and GND. Table 2 summarizes resistor values for various overvoltage protection trip points. Use 1% tolerance metal film resistors for programming the desired OVP trip point. R6 (KΩ) R5 (KΩ) VOVP_TRIP POINT (V) short 0.499 1.3 3.01 open open open open open open open open open open 4.99 2.49 1.0 short 7.5 7.25 7.0 6.75 6.5 5.5 5.0 4.5 3.87 BATS pin may be terminated to the BAT pin using a 10kΩ resistor. Under normal operation, the connection to the battery terminal will be close to 0Ω; if the BATS connection becomes an open circuit, the 10kΩ resistor will provide feedback to the BATS pin from the BAT connection with a voltage sensing accuracy loss of 1mV or less. Constant Charge Current The constant current mode charge level is user programmed with a set resistor placed between the ISET pin and ground. The accuracy of the constant charge current, as well as the preconditioning trickle charge current, is dominated by the tolerance of the set resistor used. For this reason, a 1% tolerance metal film resistor is recommended for the set resistor function. The constant charge current levels from 100mA to 1A may be set by selecting the appropriate resistor value from Table 3. Constant Charging Current (mA) Set Resistor Value (kΩ) 10 20 50 100 200 300 400 500 600 700 800 900 1000 162 80.6 32.4 16 8.06 5.36 4.02 3.24 2.67 2.26 2 1.78 1.62 Table 2: Programming OVP Trip Point for AAT3783 with One Resistor. Battery Connection and Battery Voltage Sensing Battery Connection (BAT) Battery Voltage Sensing (BATS) The BATS pin is provided to employ an accurate voltage sensing capability to measure the positive terminal voltage at the battery cell being charged. This function reduces measured battery cell voltage error between the battery terminal and the charge control IC. The AAT3783 charge control circuit will base charging mode states upon the voltage sensed at the BATS pin. The BATS pin must be connected to the battery terminal for correct operation. If the battery voltage sense function is not needed, the BATS pin should be terminated directly to the BAT pin. If there is concern of the battery sense function inadvertently becoming an open circuit, the 14 Table 3: RSET Values. Constant Charging Current (mA) A single cell Li-Ion/Polymer battery should be connected between the BAT pin and ground. 10000 1000 100 10 1 1 10 100 1000 RSET (kΩ Ω) Figure 2: Constant Charging Current vs. Set Resistor Values. www.analogictech.com 3783.2008.08.1.2 PRODUCT DATASHEET AAT3783 BatteryManagerTM 1-A Linear Li-Ion/Polymer Battery Charger with 28V Over-Voltage Protection Charge Termination Current The charge termination current ICH_TERM can be programmed by connecting a resistor from TERM to GND: ICH_TERM = 15µA · RTERM · ICH_CC 2V Time 25 minutes 3 hours 3 hours Table 4: Summary for a 0.1μF Ceramic Capacitor Used for the Timing Capacitor. Where: ICH_TERM = Charge termination current level ICH_CC = Programmed fast charge constant current level RTERM = TERM resistor value If the TERM pin is left open, the termination current will set to 10% of the constant charging current as the default value. When the charge current drops to the defaulted 10% of the programmed charge current level or programmed terminated current in the constant voltage mode, the device terminates charging and goes into a sleep state. The charger will remain in this sleep state until the battery voltage decreases to a level below the battery recharge voltage threshold (VRCH). Consuming very low current in sleep state, the AAT3783 minimizes battery drain when it is not charging. This feature is particularly useful in applications where the input supply level may fall below the battery charge or under-voltage lockout level. In such cases where the AAT3783 input voltage drops, the device will enter sleep state and automatically resume charging once the input supply has recovered from the fault condition. Protection Circuitry Programmable Watchdog Timer The AAT3783 contains a watchdog timing circuit to shut down charging functions in the event of a defective battery cell not accepting a charge over a preset period of time. Typically, a 0.1μF ceramic capacitor is connected between the CT pin and ground. When a 0.1μF ceramic capacitor is used, the device will time out a shutdown condition if the trickle charge mode exceeds 25 minutes and a combined trickle charge plus constant current mode of 3 hours. When the device transitions to the constant voltage mode, the timing counter is reset and will time out after an additional 3 hours if the charge current does not drop to the charge termination level. 3783.2008.08.1.2 Mode Trickle Charge (TC) Time Out Trickle Charge (TC) + Constant Current (CC) Mode Time Out Constant Voltage (CV) Mode Time Out The CT pin is driven by a constant current source and will provide a linear response to increase in the timing capacitor value. Thus, if the timing capacitor were to be doubled from the nominal 0.1μF value, the time-out periods would be doubled. If the programmable watchdog timer function is not needed, it can be disabled by terminating the CT pin to ground. The CT pin should not be left floating or un-terminated, as this will cause errors in the internal timing control circuit. The constant current provided to charge the timing capacitor is very small, and this pin is susceptible to noise and changes in capacitance value. Therefore, the timing capacitor should be physically located on the printed circuit board layout as close as possible to the CT pin. Since the accuracy of the internal timer is dominated by the capacitance value, a 10% tolerance or better ceramic capacitor is recommended. Ceramic capacitor materials, such as X7R and X5R types, are a good choice for this application. Battery Over-Voltage Protection An over-voltage event is defined as a condition where the voltage on the BAT pin exceeds the maximum battery charge voltage and is set by the over-voltage protection threshold (VBOVP). If an over-voltage condition occurs, the AAT3783 charge control will shut down the device until the voltage on the BAT pin drops below VOVP. The AAT3783 will resume normal charging operation after the over-voltage condition is removed. Battery Temperature Monitoring In the event of a battery over-temperature condition, the charge control will turn off the internal pass device. After the system recovers from a temperature fault, the device will resume charging operation. The AAT3783 checks battery temperature before starting the charge cycle, as well as during all stages of charging. This is accomplished by monitoring the voltage at the TS pin. This system is intended for use with negative temperature coefficient thermistors (NTC) which are typically integrated into the battery package. Most of the commonly used NTC therm- www.analogictech.com 15 PRODUCT DATASHEET AAT3783 BatteryManagerTM 1-A Linear Li-Ion/Polymer Battery Charger with 28V Over-Voltage Protection Over-Temperature Shutdown The AAT3783 has a thermal protection control circuit which will shut down charging functions should the internal die temperature exceed the preset thermal limit threshold. Once the internal die temperature falls below the thermal limit, normal operation will resume the previous charging state. Digital Thermal Loop Control Due to the integrated nature of the linear charging control pass device for the adapter mode, a special thermal loop control system has been employed to maximize charging current under all operation conditions. The thermal management system measures the internal circuit die temperature and reduces the fast charge current when the device exceeds a preset internal temperature control threshold. Once the thermal loop control becomes active, the fast charge current is initially reduced by a factor of 0.44. The initial thermal loop current can be estimated by the following equation: The AAT3783 is designed to deliver a continuous charging current. The limiting characteristic for maximum safe operating charging current is its package power dissipation. Many considerations should be taken into account when designing the printed circuit board layout, as well as the placement of the IC package in proximity to other heat generating devices in a given application design. The ambient temperature around the IC will also have an effect on the thermal limits of a battery charging application. The maximum limits that can be expected for a given ambient condition can be estimated by the following discussion. First, the maximum power dissipation for a given situation should be calculated: PD(MAX) = (TJ(MAX) - TA) θJA Where: PD(MAX) = θJA = TJ = TA = Maximum Power Dissipation (W) Package Thermal Resistance (°C/W) Thermal Loop Entering Threshold (°C) [115ºC] Ambient Temperature (°C) Figure 3 shows the relationship of maximum power dissipation and ambient temperature of AAT3783. 2.5 2 1.5 1 0.5 0 ITLOOP = ICH_CC · 0.44 0 The thermal loop control re-evaluates the circuit die temperature every three seconds and adjusts the fast charge current back up in small steps to the full fast charge current level or until an equilibrium current is discovered and maximized for the given ambient temperature condition. The thermal loop controls the system charge level; therefore, the AAT3783 will always provide the highest level of constant current in the fast charge mode possible for any given ambient temperature condition. 16 Thermal Considerations and High Output Current Applications PD(MAX) (W) istors in battery packs are approximately 10kΩ at room temperature (25°C). The TS pin has been specifically designed to source 75μA of current to the thermistor. The voltage on the TS pin resulting from the resistive load should stay within a window of 331mV to 2.39V. If the battery becomes too hot during charging due to an internal fault or excessive constant charge current, the thermistor will heat up and reduce in value, pulling the TS pin voltage lower than the TS1 threshold, and the AAT3783 will stop charging until the condition is removed, when charging will be resumed. If the use of the TS pin function is not required by the system, it should be terminated to ground using a 10kΩ resistor. Alternatively, on the AAT3783, the TS pin may be left open. 25 50 75 100 TA (°C) Figure 3: Maximum Power Dissipation Before Entering Digital Thermal Loop. Next, the power dissipation can be calculated by the following equation: www.analogictech.com PD = [(VIN - VBAT) · ICH + (VIN · IOP)] 3783.2008.08.1.2 PRODUCT DATASHEET AAT3783 BatteryManagerTM 1-A Linear Li-Ion/Polymer Battery Charger with 28V Over-Voltage Protection Where: PD VIN VBAT ICH IOP = = = = Total Power Dissipation by the Device Input Voltage Battery Voltage as Seen at the BAT Pin Constant Charge Current Programmed for the Application = Quiescent Current Consumed by the Charger IC for Normal Operation [0.4mA] By substitution, we can derive the maximum charge current before reaching the thermal limit condition (thermal loop). The maximum charge current is the key factor when designing battery charger applications. no specific capacitor equivalent series resistance (ESR) requirement for CIN. However, for higher current operation, ceramic capacitors are recommended for CIN due to their inherent capability over tantalum capacitors to withstand input current surges from low impedance sources such as batteries in portable devices. Typically, 50V rated capacitors are required for most of the application to prevent any surge voltage. Ceramic capacitors selected as small as 1210 are available which can meet these requirements. Other voltage rating capacitor can also be used for the known input voltage application. Charger Input Capacitor (PD(MAX) - VIN · IOP) ICH(MAX) = VIN - VBAT A 2.2μF decoupling capacitor is recommended to be placed between INCHR and GND. (TJ(MAX) - TA) - V · I IN OP θJA ICH(MAX) = VIN - VBAT Charger Output Capacitor In general, the worst condition is the greatest voltage drop across the charger IC, when battery voltage is charged up to the preconditioning voltage threshold and before entering thermal loop regulation. Figure 4 shows the maximum charge current in different ambient temperatures. The AAT3783 only requires a 1μF ceramic capacitor on the BAT pin to maintain circuit stability. This value should be increased to 10μF or more if the battery connection is made any distance from the charger output. If the AAT3783 is used in applications where the battery can be removed from the charger, such as with desktop charging cradles, an output capacitor greater than 10μF may be required to prevent the device from cycling on and off when no battery is present. 1000 TA = 45°C ICC_MAX (mA) Printed Circuit Board Layout Recommendations TA = 25°C 800 600 400 200 TA = 85°C TA = 60°C 0 4 4.5 5 5.5 6 6.5 7 7.5 VIN (V) Figure 4: Maximum Charging Current Before the Digital Thermal Loop Becomes Active. Input Capacitor A 1μF or larger capacitor is typically recommended for CIN. CIN should be located as close to the device VIN pin as practically possible. Ceramic, tantalum, or aluminum electrolytic capacitors may be selected for CIN. There is 3783.2008.08.1.2 For proper thermal management and to take advantage of the low RDS(ON) of the AAT3783, a few circuit board layout rules should be followed: VIN and VOUT should be routed using wider than normal traces, and GND should be connected to a ground plane. To maximize package thermal dissipation and power handling capacity of the AAT3783 DFN34 package, solder the exposed paddle of the IC onto the thermal landing of the PCB, where the thermal landing is connected to the ground plane. This AAT3783 has two exposed paddles (EP1 and EP2). EP1 is connected to INCHR (pin 1) and EP2 is connected to GND (pin 13). DO NOT make one whole thermal landing! If heat is still an issue, multi-layer boards with dedicated ground planes are recommended. Also, adding more thermal vias on the thermal landing would help the heat being transferred to the PCB effectively. www.analogictech.com 17 PRODUCT DATASHEET AAT3783 BatteryManagerTM 1-A Linear Li-Ion/Polymer Battery Charger with 28V Over-Voltage Protection JP3 INCHR INCHR +5V Red LED D1 JP1 Enable R3 (open) U1 R7 6k 4V - 7.5V VIN GND 2 1 R5 (open) C1 1μF INCHR R6 (open) C2 2.2μF R8 1.5k 7 5 15 16 6 FLT ENOVP IN IN OVP ADPP STAT BATS BAT TS 9 8 2 3 4 11 ENCHR TERM 12 1 INCHR ISET 14 CT 10 INCHR 13 JP2 GND AAT3783 Red LED Green LED D2 D3 R9 1.5k 1 2 3 C4 0.1μF GND BAT TS C3 10μF R1 1.62k R2 13.3k R4 10k EN_CHR C1 1206 X7R 1μF 50V GRM31MR71H105KA88 (C1 1206 X7R 2.2μF 50V GRM31CR71H225KA88L) (C1 1210 X7R 4.7μF 50V GRM32ER71H475KA88L) C2 0805 X5R 2.2μF 10V GRM188R61A225KE34 C3 0805 X7R 10μF 10V GRM21BR71A106KE51L Figure 5: AAT3783 Evaluation Board Schematic. Component Part# Description U1 AAT3783IRN R1 R2 R4 R7 R8, R9 C1 C2 C3 C4 JP1, JP2, JP3 D1, D2 D3 Chip Resistor Chip Resistor Chip Resistor Chip Resistor Chip Resistor GRM31MR71H105KA88 GRM188R61A225KE34 GRM21BR71A106KE51L GRM188R71E104KA01 PRPN401PAEN CMD15-21SRC/TR8 CMD15-21VGC/TR8 1A Linear Li-Ion/Polymer Battery Charger with 28V Over-Voltage Protection; TDFN Package 1.62KΩ, 1%, 1/4W; 0603 13.3KΩ, 1%, 1/4W; 0603 10KΩ, 5%, 1/4W; 0603 6KΩ, 5%, 1/4W; 0603 1.5KΩ, 5%, 1/4W; 0603 CER 1μF 50V 10% X7R 1206 CER 2.2μF 10V 10% X5R 0805 CER 10μF 10V 10% X7R 0805 CER 0.1μF 25V 10% X7R 0603 Conn. Header, 2mm zip Red LED; 1206 Green LED; 1206 Manufacturer AnalogicTech Vishay Vishay Vishay Vishay Vishay Murata Murata Murata Murata Sullins Electronics Chicago Miniature Lamp Chicago Miniature Lamp Table 5: AAT3783 Evaluation Board Bill of Materials. 18 www.analogictech.com 3783.2008.08.1.2 PRODUCT DATASHEET AAT3783 BatteryManagerTM 1-A Linear Li-Ion/Polymer Battery Charger with 28V Over-Voltage Protection Figure 5: AAT3783 Evaluation Board Top Layer. Figure 6: AAT3783 Evaluation Board Middle Layer. Figure 7: AAT3783 Evaluation Board Bottom Layer. Figure 8: Magnified View of Exposed Paddles on AAT3783 Evaluation Board Top Layer. 3783.2008.08.1.2 www.analogictech.com 19 PRODUCT DATASHEET AAT3783 BatteryManagerTM 1-A Linear Li-Ion/Polymer Battery Charger with 28V Over-Voltage Protection Ordering Information Package Marking1 Part Number (Tape and Reel)2 TDFN34-16 XQXYY AAT3783IRN-4.2-T1 All AnalogicTech products are offered in Pb-free packaging. The term “Pb-free” means semiconductor products that are in compliance with current RoHS standards, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. For more information, please visit our website at http://www.analogictech.com/about/quality.aspx. Package Information TDFN34-16 1.600 ± 0.050 0.35 REF R0.15 (REF) Pin 1 ID 0.450 ± 0.050 0.230 ± 0.050 4.000 ± 0.050 Index Area 2.350 ± 0.050 0.700 ± 0.050 3.000 ± 0.050 0.25 REF 0.430 ± 0.050 1.600 ± 0.050 0.750 ± 0.050 Top View 0 + 0.100 -0.000 Bottom View 0.230 ± 0.050 Side View All dimensions in millimeters. 1. XYY = assembly and date code. 2. Sample stock is generally held on part numbers listed in BOLD. 3. The leadless package family, which includes QFN, TQFN, DFN, TDFN and STDFN, has exposed copper (unplated) at the end of the lead terminals due to the manufacturing process. A solder fillet at the exposed copper edge cannot be guaranteed and is not required to ensure a proper bottom solder connection. Advanced Analogic Technologies, Inc. 3230 Scott Boulevard, Santa Clara, CA 95054 Phone (408) 737-4600 Fax (408) 737-4611 © Advanced Analogic Technologies, Inc. AnalogicTech cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in an AnalogicTech product. No circuit patent licenses, copyrights, mask work rights, or other intellectual property rights are implied. AnalogicTech reserves the right to make changes to their products or specifications or to discontinue any product or service without notice. Except as provided in AnalogicTech’s terms and conditions of sale, AnalogicTech assumes no liability whatsoever, and AnalogicTech disclaims any express or implied warranty relating to the sale and/or use of AnalogicTech products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. Testing and other quality control techniques are utilized to the extent AnalogicTech deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed. AnalogicTech and the AnalogicTech logo are trademarks of Advanced Analogic Technologies Incorporated. All other brand and product names appearing in this document are registered trademarks or trademarks of their respective holders. 20 www.analogictech.com 3783.2008.08.1.2