A-POWER APU1205-30

Technology Licensed from International Rectifier
APU1205
APU1205-18 / APU1205-25 / APU1205-28
APU1205-30 / APU1205-33 / APU1205-36
300mA ULTRA LOW DROPOUT POSITIVE
ADJUSTABLE AND FIXED REGULATORS
DESCRIPTION
FEATURES
SOT-23 Package
Stable with 2.2mF Ceramic Capacitor
1% Voltage Reference Accuracy
Only 270mV Dropout at 300mA
and 170mV Dropout at 150mA
5mA Quiescent Current in Shutdown
Current Limit and Thermal Shutdown
Logic Input Enable Pin
RoHS Compliant
The APU1205 device is an efficient linear voltage regulator with better than 1% initial voltage accuracy, very low
dropout voltage and very low ground current designed
especially for hand held, battery powered applications.
Other features of the device are: TTL compatible enable/
shutdown control input, current limiting and thermal shutdown.
The APU1205 is available in fixed and adjustable output
voltage versions in a small SOT-23 5-Pin package.
APPLICATIONS
Laptop, Notebook & Palmtop computers
Battery Powered Equipments
PCMCIA Vcc & Vpp Regulator
Consumer Electronics
High Efficiency Linear Power Supplies
TYPICAL APPLICATION
VIN
1
VIN
VOUT
5
C1
2.2uF
VOUT
R1
2
Gnd
3
En
(
Vo = 1.253 1+
C2
2.2uF
R1
R2
)
R2
SD
Enable
Adj
4
Figure 1 - Typical application of the APU1205 ajustable voltage regulator.
3.3V
1
VIN
2
Gnd
3
En
VOUT
5
2.5V
C1
2.2uF
SD
Enable
C2
2.2uF
CBYP
4
C3
1000pF
Figure 2 - Typical application of the APU1205-25 fixed voltage regulator.
PACKAGE ORDER INFORMATION
TJ (°C)
0 To 125
0 To 125
0 To 125
0 To 125
0 To 125
0 To 125
0 To 125
5-PIN
SOT-23
APU1205Y5
APU1205Y5-18
APU1205Y5-25
APU1205Y5-28
APU1205Y5-30
APU1205Y5-33
APU1205Y5-36
Data and specifications subject to change without notice.
OUTPUT
VOLTAGE
Adj
1.8V
2.5V
2.8V
3.0V
3.3V
3.6V
200724062-1/4
APU1205
APU1205-18 / APU1205-25 / APU1205-28
APU1205-30 / APU1205-33 / APU1205-36
ABSOLUTE MAXIMUM RATINGS
Input Voltage (V IN) .....................................................
Enable Input Voltage .................................................
Storage Temperature Range .......................................
Operating Junction Temperature Range ......................
10V
10V
-65°C To 150°C
0°C To 150°C
PACKAGE INFORMATION
5-PIN SOT-23 (Y5)
5-PIN SOT-23 (Y5)
En Gnd VIN
3
2
En Gnd VIN
1
3
2
1
Fixed
Adjustable
4
5
Adj
VOUT
uJA=2568C/W
4
5
CBYP
VOUT
uJA=2568C/W
ELECTRICAL SPECIFICATIONS
Unless otherwise specified, these specifications apply over CIN=Co=22mF, Io=100mA, VIN(MIN)=2.5V(Adjustable
devices) VIN=Vo + 1V(for fixed voltage devices), VOUT=VFB(for adjustable version only), CBYP=470pF(for fixed voltage devices),
VENB=2V and TA=258C. Typical values refer to TA=258C. Low duty cycle pulse testing is used which keeps junction and
case temperatures equal to the ambient temperature.
PARAMETER
Reference Voltage
(See Table 1 for typical values)
Line Regulation
Load Regulation (Note 1)
SYM
Vo
Dropout Voltage (Note 2)
DVI(O)
Ground Current (Note 3)
IQ
Ground Current-SD Activated
Current Limit
Thermal Regulation
Adjust Pin Current
Enable Pin Input LO Voltage
Enable Pin Input HI Voltage
Enable Pin Input LO Current
Enable Pin Input HI Current
DVI
DVL
IQ(SD)
ICL
DVP
IADJ
VEN(L)
VEN(H)
TEST CONDITION
(Note 4)
Vo + 1V<VIN<10V
1mA<Io<100mA
100mA<Io<300mA
Io=100mA
Io=100mA (Note 4)
Io=50mA
Io=50mA (Note 4)
Io=150mA
Io=150mA (Note 4)
Io=300mA
Io=300mA (Note 4)
VEN =2V, Io=100mA
Io=100mA (Note 4)
Io=50mA
Io=50mA (Note 4)
Io=150mA
Io=150mA (Note 4)
Io=300mA
Io=300mA (Note 4)
VEN =0V to 0.8V or Open
Vo=0V
VIN=10V, Io=150mA, 10ms Pulse
VIN=2.5V, Vo=VADJ
Regulator OFF
Regulator ON
VEN(L) =0V to 0.8V
VEN(H)=2V to VIN
MIN
-1
-2
320
TYP
0.005
0.8
0.1
10
13
85
100
170
204
270
324
120
240
420
540
2200
2900
7200
9300
5
420
0.05
0.1
MAX UNITS
1
%
2
%/V
%
50
70
110
140
220
260
350
400
160
0.01
20
mA
600
2900
9500
0.8
2
mV
mA
mA
%/W
mA
V
V
mA
mA
2/4
APU1205
APU1205-18 / APU1205-25 / APU1205-28
APU1205-30 / APU1205-33 / APU1205-36
Note 1: Low duty cycle pulse testing with Kelvin connections is required in order to maintain accurate data.
Note 2: Dropout voltage is defined as the minimum differential voltage between VIN and VOUT required to maintain regulation at VOUT. It is measured when the output
voltage drops 1% below its nominal value.
Note 3: Ground current is the regulator quiescent current plus the pass transistor current. The total current
from the supply is the sum of the load current plus the
ground pin current.
Note 4: The specification applies for the junction temperature of 0 to +1258C.
PIN DESCRIPTIONS
PIN #
1
PIN SYMBOL
VIN
PIN DESCRIPTION
The input pin of the regulator. Typically a large storage capacitor is connected from
this pin to ground to insure that the input voltage does not sag below the minimum
drop out voltage during the load transient response. This pin must always be higher
than VOUT by at least the amount of the dropout voltage and some margin in order for
the device to regulate properly.
2
Gnd
Ground pin. This pin must be connected to the lowest potential in the system and all
other pins must be at higher potential with respect to this pin.
3
En
Enable pin. A low signal or left open on this pin shuts down the output. This pin must
be tied HI or to VIN for normal operation.
4
Adj
(Adjustable Only)
A resistor divider from this pin to the VOUT pin and ground sets the output voltage. To
minimize the error due to the error amplifier, select the values of the resistor dividers
to be less than 10KV.
4
CBYP
(Fixed Only)
A 470 to 1000pF bypass capacitor connected to this pin reduces the output noise.
5
VOUT
The output of the regulator. A minimum of 2.2mF with max ESR of 1V capacitor must
be connected from this pin to ground to insure stability.
5-PIN
SOT-23
APU1205
APU1205-18
APU1205-25
APU1205-28
APU1205-30
APU1205-33
APU1205-36
Output
Voltage
1.25V
1.8V
2.5V
2.8V
3.0V
3.3V
3.6V
The output voltage of the adjustable device can be set
using:
(
Vo = 1.253 1+
R1
R2
)
Where:
R1 = Resistor connected from output to the Adj pin
R2 = Resistor connected from Adj pin to Gnd
Table 1- Nominal output voltage vs. part number.
3/4
APU1205
APU1205-18 / APU1205-25 / APU1205-28
APU1205-30 / APU1205-33 / APU1205-36
BLOCK DIAGRAM
5 VOUT
VIN 1
Adj
4
THERMAL
SHUTDOWN
1.25V
+
3 En
Gnd 2
Figure 3 - APU1205 Adjustable output block diagram.
VIN 1
CBYP
5 VOUT
THERMAL
SHUTDOWN
4
+
1.25V
Gnd 2
3 En
Figure 4 - APU1205-18, APU1205-25, APU1205-28, APU1205-30, APU1205-33 and
APU1205-36 Fixed output block diagram.
4/4