NON-ISOLATED DC/DC CONVERTERS 4.5 V-14 V Input 0.75 V-3.63 V/10 A Output V7BC-10E2Ax Series • Non-Isolated • Wide Input • High Efficiency • Wide Trim • High Power Density • OCP/SCP • Excellent Thermal Performance • Remote On/Off • Low Cost • Active Low/High (option) • Flexible Output Voltage Sequencing (option) • Over Temperature Protection • Under-voltage Lockout (UVLO) Remote Sense • Industrial Temperature Range • Description The Bel V7BC-10E2Ax is part of the non-isolate dc/dc power converter series. The modules use a SIP package. These converters are available in a range of output voltages from 0.75 V to 3.63 V over a wide range of input voltage (Vin = 4.5 V-14 V). The Bel V7BC-10E2Ax has a sequencing feature that enables designers to implement various types of output voltage sequencing when powering. The efficiency is typically 94.3% at 3.3V output at 5.0V input at full load. Part Selection Output Voltage Input Voltage Max. Output Current Max. Output Power Typical Efficiency Model Number Active Low Model Number Active High 0.75 V- 3.63 V 4.5 V – 14 V 10 A 36.3 W 94.3% V7BC-10E2AL V7BC-10E2A0 Note: Add “G” suffix at the end of the model number to indicate Tray Packaging. Absolute Maximum Ratings Parameter Min Typ Max Input Voltage (continuous) -0.3 V - 15 V Output Enable Terminal Voltage -0.3 V - 15 V 1 -0.3 V - Vin Ambient Temperature -40 °C - 85 °C Storage Temperature -55 °C - 125 °C Sequencing Voltage Notes Notes: All specifications are typical at 25 °C unless otherwise stated. 1. V7BC-10E2Ax series of modules include a sequencing feature that enables users to implement various types of output voltage sequencing in their applications. This is accomplished via an additional sequencing pin. When not using the sequencing feature, either tie the SEQ pin to Vin or leave it unconnected. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 V-14 V Input 0.75 V-3.63 V/10 A Output Input Specifications Parameter Min Typ Max Notes 4.5 V Vo,set+1.5 V - 14 V 14 V Input Current (full load) - - 8.6 A Input Current (no load) Remote Off Input Current - 40 mA 2 mA - Input Reflected Ripple Current (pkpk) - - 400 mA Input Reflected Ripple Current (rms) - - 150 mA - 0.2 A s 4.3 V 4.0 V Input Voltage Vo,set < 3.0 V Vo,set ≥ 3.0 V 2 I t Inrush Current Transient Turn-on Voltage Threshold Turn-off Voltage Threshold 2 An input line fuse must always be used. Tested with one 1000uF/25V AL input capacitor with ESR=0.03 ohm max and 4 × 47 uF/16 V Tantalum capacitors with ESR=0.013 ohm max at 100 kHz, & simulated source impedance of 1000 nH, 5 Hz to 20 MHz. 2 0.4 A s - Note: All specifications are typical at 25 °C unless otherwise stated. Output Specifications Parameter Output Voltage Set Point Load Regulation Line Regulation Regulation Over Temperature (-40°C to +85°C) Output Current Current Limit Threshold Short Circuit Surge Transient Min -2% Vo,set - Typ 0.1% Vo,set 0.1% Vo,set Max 2% Vo,set - Notes Vin=5V & 12V, full load - 0.3Vo,set - Tref=Ta, min to Ta, max 0A - 200% Io,out 2 1A s 10 A 2 3A s Ripple and Noise (pk-pk) - 30 mV 80 mV Ripple and Noise (rms) - 12 mV 35 mV 0 uF 8 mS 0% - 20 mS 1% 5600 uF Turn on Time Overshoot at Turn on Output Capacitance Transient Response 50% ~ 100% Max Load Settling Time 100% ~ 50% Max Load Settling Time VO = 0.75 V 3.63 V - 160 mV 50 uS 160 mV 50 uS - Tested with 0-20MHz, with 10uF tantalum capacitor & 1uF ceramic capacitor at the output di/dt=2.5 A/uS; Vin=5 V & 12 V; and with 470 uF Tantalum capacitor at the output Note: All specifications are typical at nominal input, full load at 25 °C unless otherwise stated. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 V-14 V Input 0.75 V-3.63 V/10 A Output General Specifications Parameter Min Typ Max Notes Vo=3.3 V Vo=2.5 V Vo=1.8 V Vo=1.5 V Vo=1.2 V Vo=0.75 V - 94.3% 93% 91.5% 90.8% 89.3% 83% - Vo=3.3 V Vo=2.5 V Vo=1.8 V Vo=1.5 V Vo=1.2 V Vo=0.75 V - 93% 92% 90% 89% 87.5% 81% - 265 kHz 300 kHz 335 kHz - 130°C - 0.7525 V - 3.63 V - - 0.5 V Efficiency Measured at Vin=5V, full load Efficiency Switching Frequency Over Temperature Shutdown Output Voltage Trim Range Remote Sense Compensation MTBF Measured at Vin=12V, full load Calculated Per Bell Core TR-332 (IO = 80%Io,max; Vo=3.3 V; Vin=12 V; Ta = 25 °C) 5,114,191 hours Dimensions Inches (L × W × H) Millimeters (L × W × H) 2.0 x 0.5 x 0.32 50.8 x 12.7 x 8.13 Weight - 7.1 g - Note: All specifications are typical at 25 °C unless otherwise stated. Control Specifications Parameter Min Typ Max Notes Signal Low (Unit Off) -0.2 V - 0.3 V Signal High (Unit On) - - Vin, max V7BC-10E2A0; Remote On/Off pin open, Unit on. Signal Low (Unit On) -0.2 V - 0.3 V Signal High (Unit Off) 2.5 V - Vin, max 25 mS - - - - 2 V/mS - 100 mV 300 mV 200 mV 500 mV Remote On/Off V7BC-10E2AL; Remote On/Off pin open, Unit on. Voltage Sequencing Sequencing Delay Time Sequencing Slew Rate Capability Tracking Accuracy Power-Up Power-Down Delay from Vin, min to application of voltage on SEQ pin Vin, min to Vin, max; Io, min to Io, max; Vseq<Vo Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 V-14 V Input 0.75 V-3.63 V/10 A Output Output Trim Equations Equation for calculating the trim resistor (in Ω) given the desired output voltage (Vo) is shown below. The Trim Up resistor should be connected between the Trim pin and Ground. Vout Sense Rtrim = 10500 − 1000 Vo − 0.7525 Module trim Rtrim GND Equation for calculating the trim voltage (in V) given the desired output voltage (Vo) is shown below. The Trim Up voltage should be connected between the Trim pin and Ground. Vout Vtrim = 0.7 − 0.0667 × (Vo − 0.7525) Sense Module trim Vtrim GND Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 V-14 V Input 0.75 V-3.63 V/10 A Output Efficiency Data Module 2.5 V 5.0V 12.0V 5.0 7.5 5.0V 12.0V 90% 80% 1.0 2.5 5.0 7.5 Output Current (A) Output Current (A) Module 1.8 V Module 1.5 V 5.0V 12.0V 80% 70% 2.5 5.0 7.5 5.0V 12.0V 1.0 2.5 5.0 7.5 Output Current (A) Output Current (A) Module 1.2 V Module 0.75 V 5.0V 12.0V 70% 50% 2.5 5.0 7.5 Output Current (A) 10.0 10.0 100% 90% 80% 70% 10.0 90% 1.0 100% 10.0 100% 90% 1.0 Efficiency 2.5 Efficiency Efficiency 1.0 Efficiency 100% 90% 80% 70% Efficiency Efficiency Module 3.3 V 10.0 110% 90% 70% 50% 5.0V 12.0V 1.0 2.5 5.0 7.5 10.0 Output Current (A) Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 V-14 V Input 0.75 V-3.63 V/10 A Output Thermal Derating Curves Vin=12 V, Vo = 3.3 V Vin=5 V, Vo = 3.3 V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 V-14 V Input 0.75 V-3.63 V/10 A Output Pin Connections Pin Function 1 Vout 2 Vout 3 Remote Sense 4 Vout 5 Ground 6 Ground 7 Vin 8 Vin 9 SEQ 10 Trim 11 Remote On/Off 2004 Bel Fuse Inc. Specifications subject to change without notice. 040805 CORPORATE FAR EAST EUROPE Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com Bel Fuse Ltd. 8F/ 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com