NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input 0.75 Vdc - 5.0 Vdc/6 A Output VRBA-06E1Ax RoHS Compliant Rev.A • Non-Isolated • Under-Voltage Lockout (UVLO) • High Efficiency • Remote On/Off • High Power Density • OCP/SCP • Fixed Frequency • Wide Input • Active Low/High (Option) • Wide Trim Range Description The Bel VRBA-06E1Ax modules are a series of non-isolated dc/dc converters that can deliver up to 6 A of output current with full load efficiency of 92% at 5.0 Vdc output. These modules provide precisely regulated voltage programmable via external resistor from 0.75 Vdc to 5.0 Vdc over a wide range of input voltage. Their open-frame construction and small footprint enable designers to develop cost and space-efficient solutions. Standard features include remote On/Off, programmable output voltage and over current protection. Part Selection Output Voltage 5.0 V 0.75 V - 3.3 V Input Voltage 7.0 V -14 V 4.5 V - 14 V Max. Output Current 6A 6A Max. Output Power 30.0 W 19.8 W Typical Efficiency 92% 88% Model Number Active Low VRBA-06E1AL VRBA-06E1AL Model Number Active High VRBA-06E1A0 VRBA-06E1A0 Notes: 1. Add “G” suffix at the end of the model numbers to indicate Tray Packaging. 2. All part numbers above indicate RoHS 6. Change the second letter "R" to "7" for RoHS 5 part numbers. Absolute Maximum Ratings Parameter Input Voltage (continuous) Output Enable Terminal Voltage Ambient Temperature Storage Temperature Min -0.3 V -0.3 V -40 °C -55 °C Typ - Max 15 V 15 V 85 °C 125 °C Notes Note: All specifications are typical at 25 °C unless otherwise stated. Input Specifications Parameter Min Typ Max 4.5 V 7.0 V 12 V 12 V 14 V 14 V Vo=5.0 V Vo=3.3 V Vo=1.8 V Vo=0.75 V - 2.75 A 1.85 A 1.05 A 0.55 A 4.8 A 4.8 A 3.2 A 1.8 A Vo=5.0 V Vo=0.75 V Remote Off Input Current - 3 mA 100 mA 20 mA 5 mA Input Reflected Ripple Current (pk-pk) - 120 mA 200 mA Input Reflected Ripple Current (rms) - 60 mA 100 mA Notes Input Voltage Vo, set ≤ 3.3 V Vo, set = 5.0 V Input Current (full load) Input Current (no load) Tested with two 100 uF/25 V input Tantalum capacitors & simulated source impedance of 1uH, 5 Hz to 20 MHz. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input 0.75 Vdc - 5.0 Vdc/6 A Output Input Specifications (continue) Parameter Min 2 I t Inrush Current Transient Typ Max 2 Notes 2 - 0.002 A s 0.02 A s - 4.3 V 6.0 V 4.5 V 6.5 V - 4.0 V 5.5 V 4.3 V 6.0 V Turn-on Voltage Threshold Vo, set ≤ 3.3 V Vo, set = 5.0 V Turn-off Voltage Threshold Vo, set ≤ 3.3 V Vo, set = 5.0 V Shut down or below 90% set point. Note: All specifications are typical at 25 °C unless otherwise stated. Output Specifications Min Typ Max Output Voltage Set Point Parameter -2%Vo,set - 2%Vo,set Output Voltage Set Point -2.5%Vo,set - 3.5%Vo,set Load Regulation - 0.4%Vo,set - Io=Iomin to Iomax Line Regulation - 0.3%Vo,set - Vin=Vinmin to Vinmax Regulation Over Temperature (-40°C to +85°C) - 0.5%Vo,set - Tref=Tamin to Tamax 0A - 6A 6.8 A - Output Current Current Limit Threshold Short Circuit Surge Transient Notes Vin=12 V, Io=Io max Over all operating input voltage, resistive load, and temperature conditions 15 A 2 - 0.25 A s - Vo=5.0 V Vo=3.3 V Vo=0.75 V - 100 mV 80 mV 35 mV 140 mV 120 mV 70 mV Vo=5.0 V Vo=3.3 V Vo=0.75 V - 35 mV 25 mV 10 mV 50 mV 40 mV 15 mV Turn on Time - 6 mS 12 mS Overshoot at Turn on - 0% 3% 0 uF 0 uF - 1000 uF 2200 uF - 200 mV 350 mV - 25 uS 50 uS - 200 mV 350 mV - 25 uS 50 uS Ripple and Noise (pk-pk) Ripple and Noise (rms) Tested with 0-20 MHz BW, with external 10 uF/10 V tantalum capacitor & 1 uF/10 V ceramic capacitor at the output Output Capacitance ESR ≥ 1mohm ESR ≥ 10mohm Transient Response 50% ~ 100% Max Load Settling Time 100% ~ 50% Max Load Settling Time VO = 0.75 - 5.0 V di/dt=2.5 A/uS; Vin=12 V; and with 10 uF/10 V tantalum capacitor & 1 uF/10 V ceramic capacitor at the output. Note: All specifications are typical at nominal input (Vin=12 V), full load at 25 °C unless otherwise stated. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input 0.75 Vdc - 5.0 Vdc/6 A Output General Specifications Parameter Min Typ Max Vo=5.0 V Vo=3.3 V Vo=1.8 V Vo=0.75 V Switching Frequency 88% 85% 80% 68% 220 kHz 92% 88% 84% 73% 250 kHz 280 kHz Output Voltage Trim Range (wide trim) 0.7525 V - 5V Notes Efficiency MTBF - Measured at Vin=12 V, Io=Io, max Calculated Per Bell Core TR-332 (IO = Nominal; Ta = 25 °C) 3,260,000 hours Dimensions Inches (L × W × H) Millimeters (L × W × H) 1.0 x 0.5 x 0.243 25.4 x 12.7 x 6.16 Weight - 5g Vertical Mount - Note: All specifications are typical at 25 °C unless otherwise stated. Control Specifications Parameter Remote On/Off Min Typ Max Notes Signal Low (Unit Off) -0.3 V - 0.4 V Signal High (Unit On) 2.5 V - 14 V VRBA-06E1A0; Remote On/Off pin open, Unit on. Signal Low (Unit On) -0.3 V - 0.4 V Signal High (Unit Off) 2.5 V - 14 V VRBA-06E1AL; Remote On/Off pin open, Unit on. Output Trim Equations Equation for calculating the trim resistor (in kΩ) given the desired adjusted voltage (Vadj) is shown below. The Trim Up resistor should be connected between the Trim pin and Ground. Vout Rtrim = 10.507 −1 Vadj − 0.7525 Module Trim Rtrim GND Equation for calculating the trim voltage (in V) given the desired adjusted voltage (Vadj) is shown below. The Trim Up voltage should be connected between the Trim pin and Ground. Vtrim = 0.7 − 0.0667 × (Vo − 0.7525) Vout Module Trim Vtrim GND Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input 0.75 Vdc - 5.0 Vdc/6 A Output Efficiency Data MODULE 3.3V 100.0% 100.0% 80.0% 60.0% 40.0% 20.0% 0.0% 7.0V 12.0V 14.0V EFFICIENCY EFFICIENCY MODULE 5.0V 80.0% 4.5V 12.0V 14.0V 60.0% 40.0% 20.0% 0.0% 1A 2A 3A 4A 5A 1A OUTPUT CURRENT 4A 5A MODULE 0.75V 90.0% 4.5V 12.0V 14.0V 80.0% 70.0% 60.0% EFFICIENCY 100.0% EFFICIENCY 3A OUTPUT CURRENT MODULE 1.8V 0.6A 2A 90.0% 80.0% 4.5V 12.0V 14.0V 70.0% 60.0% 50.0% 1.5A 3.0A 4.5A OUTPUT CURRENT 6.0A 0.6A 1.5A 3.0A 4.5A 6.0A OUTPUT CURRENT Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input 0.75 Vdc - 5.0 Vdc/6 A Output Thermal Derating Curves Vo=0.75 V Vo=2.5 V Vo=5 V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input 0.75 Vdc - 5.0 Vdc/6 A Output Ripple and Noise Waveforms 12 V input, 0.75 V output 12 V input, 3.3 V output 12 V input, 1.8 V output 12 V input, 5.0 V output Note: Ripple and noise at full load, 0-20 MHz BW, with 10 uF/10 V tantalum capacitor and 1 uF/10 V ceramic capacitor at the output, Ta=25 deg C. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input 0.75 Vdc - 5.0 Vdc/6 A Output Transient Response Waveforms 50% to 100% load step at Vin=12 V, Vo=0.75 V 50% to 100% load step at Vin=12 V, Vo=1.8 V 100% to 50% load step at Vin=12 V, Vo=0.75 V 100% to 50% load step at Vin=12 V, Vo=1.8 V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input 0.75 Vdc - 5.0 Vdc/6 A Output Transient Response Waveforms (continued) 50% to 100% load step at Vin=12 V, Vo=3.3 V 50% to 100% load step at Vin=12 V, Vo=5 V 100% to 50% load step at Vin=12 V, Vo=3.3 V 100% to 50% load step at Vin=12 V, Vo=5 V Note: Transient response at di/dt=2.5 A/uS, with 10 uF/10 V tantalum capacitor and 1 uF/10 V ceramic capacitor at the output, Ta=25 deg C. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input 0.75 Vdc - 5.0 Vdc/6 A Output Mechanical Outline Pin Connections Pin Function 1 Vout+ 2 Trim 3 GND 4 N/A 5 Vin+ 6 Remote On/Off RoHS Compliance Complies with the European Directive 2002/95/EC, calling for the elimination of lead and other hazardous substances from electronic products. ©2007 Bel Fuse Inc. Specifications subject to change without notice. 011207 CORPORATE FAR EAST EUROPE Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com Bel Fuse Ltd. 8F/ 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com