NON-ISOLATED DC/DC CONVERTER 12 Vdc Input 1.2 Vdc - 5.0 Vdc/15 A Output VRPF-15A1AC RoHS Compliant Rev.A • Non-Isolated • Under-Voltage Lockout (UVLO) • Fixed Frequency (220 kHz) • OCP/SCP • Wide Output Voltage Trim • Remote On/Off • Current Sink Capability for Termination Applications • Power Good Output Signal (open collector) • UL60950-1 Recognized (UL/cUL) Description The Bel VRPF-15A1AC is part of the low cost non-isolated dc/dc converter. The module uses a SIP package for ease of layout and space savings. The output is closely regulated and can be trimmed from 1.2 Vdc to 5.0 Vdc. The efficiency is typically 92% at 5.0 Vdc output at full load. Typical features include remote on/off, under-voltage lockout, over-current protection and short circuit protection. Part Selection Output Voltage Input Voltage 1.2 Vdc - 5.0 Vdc 12 Vdc Max. Output Current 15 A Max. Output Power 75 W Typical Efficiency 92% Model Number VRPF-15A1AC Notes: 1. All part numbers above indicate RoHS 6. Change the second letter "R" to "7" for RoHS 5 part numbers. 2. Add “G” suffix at the end of the model numbers listed above to indicate “Tray Packaging”. Absolute Maximum Ratings Parameter Input Voltage (continuous) Output Enable Terminal Voltage Ambient Temperature Storage Temperature Min -0.3 V -0.3 V 0 °C -40 °C Typ - Max 15 V 15 V 80 °C 125 °C Notes Input Specifications Parameter Input Voltage Input Current (Source) Min 10.8 V Typ 12 V Max 13.2 V Vo=5.0 V Vo=3.3 V Vo=2.5 V Vo=1.8 V Vo=1.5 V Vo=1.25 V Vo=1.2 V - 6.9 A 4.84 A 3.65 A 2.87 A 2.50 A 2.12 A 2.02 A - Vo=5.0 V Vo=3.3 V Vo=2.5 V Vo=1.8 V Vo=1.5 V Vo=1.25 V Vo=1.2 V - -5.9 A -3.8 A -2.7 A -1.9 A -1.6 A -1.3 A -1.1 A - Notes Input Current (Sink) Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTER 12 Vdc Input 1.2 Vdc - 5.0 Vdc/15 A Output Input Specifications (continued) Parameter Remote Off Input Current Min - Typ 25 mA Max 30 mA Input Reflected Ripple Current (pk-pk) - - 330 mA Input Reflected Ripple Current (rms) - - 120 mA I t Inrush Current Transient - 0.05 A s 0.1 A s Turn-on Voltage Threshold Turn-off Voltage Threshold - 9.8 V 9.4 V 10.4 V 10.3 V 2 2 Notes Tested with simulated source impedance of 500 nH 5 Hz to 20 MHz, and 5 × 10 uF/16 V ceramic capacitors at the input 2 Note: All specifications are typical at 25 °C unless otherwise stated. Output Specifications Parameter Output Voltage Set Point Min Typ Max Vo=5.0 V Vo=3.3 V Vo=2.5 V Vo=1.8 V Vo=1.5 V Vo=1.25 V Vo=1.2 V 4.900 V 3.234 V 2.450 V 1.764 V 1.470 V 1.225 V 1.176 V 5.0 V 3.3 V 2.5 V 1.8 V 1.5 V 1.25 V 1.2 V 5.100 V 3.366 V 2.550 V 1.836 V 1.530 V 1.275 V 1.224 V Vo=5.0 V Vo=3.3 V Vo=2.5 V Vo=1.8 V Vo=1.5 V Vo=1.25 V Vo=1.2 V - 10 mV 8 mV 5 mV 4 mV 3 mV 3 mV 2.5 mV 25.0 mV 16.5 mV 12.5 mV 9.0 mV 7.5 mV 6.3 mV 6.0 mV Vo=5.0 V Vo=3.3 V Vo=2.5 V Vo=1.8 V Vo=1.5 V Vo=1.25 V Vo=1.2 V Regulation Over Temperature (0 °C to +80 °C) Vo=5.0 V Vo=3.3 V Vo=2.5 V Vo=1.8 V Vo=1.5 V Vo=1.25 V Vo=1.2 V Output Ripple and Noise (pk-pk) Vo=5.0 V Vo=3.3 V Vo=2.5 V Vo=1.8 V Vo=1.5 V Vo=1.25 V Vo=1.2 V - 5.0 mV 3.3 mV 2.5 mV 1.8 mV 1.5 mV 1.25 mV 1.2 mV 10.0 mV 6.6 mV 5.0 mV 3.6 mV 3.0 mV 2.5 mV 2.4 mV - 10 mV 9 mV 8 mV 7 mV 6 mV 5 mV 4 mV 20 mV 18 mV 15 mV 14 mV 13 mV 12 mV 12 mV - 60 mV 50 mV 40 mV 35 mV 35 mV 30 mV 30 mV 75 mV 65 mV 60 mV 50 mV 50 mV 50 mV 50 mV Notes Test condition: Vin=12 V, lout=half load Load Regulation Line Regulation Tested at 0-20 MHz BW, with 5×10 uF/16 V ceramic capacitors at the input, and 5×10 uF/10 V ceramic capacitors and a 1000 uF electrolytic capacitor at the output. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTER 12 Vdc Input 1.2 Vdc - 5.0 Vdc/15 A Output Output Specifications (continued) Parameter Output Ripple and Noise (rms) Vo=5.0 V Vo=3.3 V Vo=2.5 V Vo=1.8 V Vo=1.5 V Vo=1.25 V Vo=1.2 V Output Current Current Limit Threshold Short Circuit Surge Transient Vo=5.0 V Vo=3.3 V Vo=2.5 V Vo=1.8 V Vo=1.5 V Vo=1.25 V Vo=1.2 V Turn on Time Overshoot at Turn on Output Capacitance Vo=5.0 V Vo=3.3 V Vo=2.5 V Vo=1.8 V Vo=1.5 V Vo=1.25 V Vo=1.2 V Min Typ Max 0A 18 mV 15 mV 12 mV 12 mV 10 mV 10 mV 10 mV - 30 mV 25 mV 20 mV 20 mV 15 mV 15 mV 15 mV 15 A 19.5 A - 37.5 A - 0.1 A s 2 0.1 A s 2 0.1 A s 2 0.3 A s 2 0.4 A s 2 0.4 A s 2 0.4 A s 20 mS 0.3 A s 2 0.3 A s 2 0.3 A s 2 0.6 A s 2 0.8 A s 2 0.8 A s 2 0.8 A s 100 mS - 0% 3% 1050 uF 1050 uF 1050 uF 1050 uF 1050 uF 1050 uF 1050 uF - 5080 uF 6000 uF 7840 uF 8500 uF 9000 uF 9500 uF 9680 uF 2 Notes Tested at 0-20 MHz BW, with 5×10 uF/16 V ceramic capacitors at the input, and 5×10 uF/10 V ceramic capacitors and a 1000 uF/16 V electrolytic capacitor at the output. 2 Transient Response 50% ~ 75% Max Load Settling Time 75% ~ 50% Max Load VO=5.0 V Settling Time 50% ~ 75% Max Load Settling Time 75% ~ 50% Max Load VO=3.3 V Settling Time 50% ~ 75% Max Load Settling Time 75% ~ 50% Max Load VO=1.25 V 2.5 V Settling Time 50% ~ 75% Max Load Settling Time 75% ~ 50% Max Load Settling Time VO=1.2 V - 100 mV 200 mV - 100 uS 200 uS - 100 mV 200 mV - 100 uS 200 uS - 80 mV 165 mV - 100 uS 200 uS - 80 mV 165 mV - 100 uS 200 uS - 60 mV 125 mV - 100 uS 200 uS - 60 mV 125 mV - 100 uS 200 uS - 60 mV 120 mV - 100 uS 200 uS - 60 mV 120 mV - 100 uS 200 uS Test conditions: di/dt = 0.1 A/uS; Vin = 12 V; with 5×10 uF ceramic capacitors and a 1000 uF/16 V electrolytic at the output Note: All specifications are typical at nominal input, full load at 25 °C unless otherwise stated. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTER 12 Vdc Input 1.2 Vdc - 5.0 Vdc/15 A Output General Specifications Parameter Min Typ Max Efficiency (Current Source) Vo=5.0 V Vo=3.3 V Vo=2.5 V Vo=1.8 V Vo=1.5 V Vo=1.25 V Vo=1.2 V 90% 87% 84% 80% 78% 76% 76% 92% 89% 87% 82% 80% 79% 79% - Notes Measured at Vin=12 V, full load. Efficiency (Current Sink) Vo=5.0 V Vo=3.3 V Vo=2.5 V Vo=1.8 V Vo=1.5 V Vo=1.25 V Vo=1.2 V Switching Frequency 88% 84% 81% 77% 73% 68% 68% 91% 87% 84% 80% 76% 71% 71% - 200 kHz 220 kHz 240 kHz 1.2 V - 5.0 V Output Voltage Trim Range MTBF Vo=1.2 V when the Trim pin is open. Calculated Per Bell Core SR-332 (IO = 12 A, Vin=12 V; Ta = 25 °C) 3,664,032 hours Dimensions Inches (L × W × H) Millimeters (L × W × H) 1.2 x 1.0 x 0.457 30.48 x 25.4 x 11.6 Weight - 14.2 g - Note: All specifications are typical at 25 °C unless otherwise stated. Control Specifications Parameter Min Typ Max Signal Low (Unit Off) 0V - 1V Signal High (Unit On) 2.4 V - 13.2 V Notes Remote On/Off Remote On/Off pin open, the module is ON. Power Good Power Good Delay 1 - - 10 mS 2 - 0.3 V - Current Sink - 5 mA - Signal Low Notes: All specifications are typical at 25 °C unless otherwise stated. 1. Power good delay time is the time from output voltage in full regulation to power good asserted. 2. The power good signal is an open collector output. When the output of the module reaches 90% of the nominal set point, the power good pin is set high. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTER 12 Vdc Input 1.2 Vdc - 5.0 Vdc/15 A Output Output Trim Equation Equation for calculating the trim resistor (in kΩ) given the desired adjusted voltage (Vadj) is shown below. The Rset resistor should be connected between the Trim pin and GND. Vout ⎛ 0.992 0.992 ⎞ Vadj = ⎜ + ⎟ ⋅ 1.18K + 0.992 ⎝ 5.62 K Rset ⎠ Module Trim Rset GND Where, Vadj is the required voltage setpoint, Rset is the resistance required between TRIM and GND. Power Good Signal Level Set Equation for calculating the power good threshold (in kΩ) given the desired adjusted voltage (Vadj) is shown below. The PWRGD_SET resistor should be connected between the PWRGD_SET pin (Pin 9) and GND. Output Voltage 5V 3.3V 2.5V 1.8V 1.5V 1.25V 1.2V PWRGD_THRESHOLD Set Resistor (1%tol) Short (Zero Ohm) 1.78k 4.22k 11.8k 26.1k 169k Open (no resistor) 1.24 ⎛ ⎞ − 18.86 ⋅ 10 −6 ⎟ + 1.24 PWRGD _ THRESHOLD = 6.19 K ⎜ ⎝ 2.21K + Rset ⎠ Where, Rset is the resistance required between PWRGD_SET and GND. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTER 12 Vdc Input 1.2 Vdc - 5.0 Vdc/15 A Output Efficiency Data Efficiency Curve Efficiency Efficiency Efficiency Curve 94.0% 92.0% 90.0% 88.0% 86.0% 84.0% 82.0% 80.0% 78.0% 76.0% 74.0% 10.8 V 12.0 V 13.2 V 1.5 3.75 7.5 11.25 92.0% 90.0% 88.0% 86.0% 84.0% 82.0% 80.0% 78.0% 76.0% 74.0% 72.0% 15 10.8 V 12.0 V 13.2 V 1.5 3.75 Output Current (A) 7.5 Vo=5.0 V Efficiency Curve Efficiency Efficiency Efficiency Curve 10.8 V 12.0 V 13.2 V 3.75 7.5 11.25 86.0% 84.0% 82.0% 80.0% 78.0% 76.0% 74.0% 72.0% 70.0% 68.0% 66.0% 64.0% 62.0% 10.8 V 12.0 V 13.2 V 1.5 15 3.75 Vo=2.5 V 10.8 V 12.0 V 13.2 V 11.25 Efficiency Efficiency 15 Efficiency Curve 84.0% 82.0% 80.0% 78.0% 76.0% 74.0% 72.0% 70.0% 68.0% 66.0% 64.0% 62.0% 60.0% 7.5 11.25 Vo=1.8 V Efficiency Curve 3.75 7.5 Output Current (A) Output Current (A) 1.5 15 Vo=3.3 V 90.0% 88.0% 86.0% 84.0% 82.0% 80.0% 78.0% 76.0% 74.0% 72.0% 70.0% 1.5 11.25 Output Current (A) 15 84.0% 82.0% 80.0% 78.0% 76.0% 74.0% 72.0% 70.0% 68.0% 66.0% 64.0% 62.0% 60.0% 58.0% 56.0% 54.0% 10.8 V 12.0 V 13.2 V 1.5 3.75 7.5 11.25 15 Output Current (A) Output Current (A) Vo=1.5 V Vo=1.25 V Efficiency Efficiency Curve 84.0% 82.0% 80.0% 78.0% 76.0% 74.0% 72.0% 70.0% 68.0% 66.0% 64.0% 62.0% 60.0% 58.0% 56.0% 54.0% 10.8 V 12.0 V 13.2 V 1.5 3.75 7.5 11.25 15 Output Current (A) Vo=1.2 V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTER 12 Vdc Input 1.2 Vdc - 5.0 Vdc/15 A Output Thermal Derating Curves Vo = 5.0 V Vo = 3.3 V Vo = 2.5 V Vo = 1.8 V Vo = 1.5 V Vo = 1.25 V Vo = 1.2 V Test Condition: The module is mounted on 2 OZ two-layer FR4 board. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTER 12 Vdc Input 1.2 Vdc - 5.0 Vdc/15 A Output Ripple and Noise Waveforms Vo=5.0 V Vo=3.3 V Vo=2.5 V Vo=1.8 V Vo=1.5 V Vo=1.25 V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTER 12 Vdc Input 1.2 Vdc - 5.0 Vdc/15 A Output Ripple and Noise Waveforms (continued) Vo=1.2 V Note: Ripple and Noise at Max Load, 12 V Input, with 5x10 uF/10 V ceramic capacitor and an 1000 uF/16 V electrolytic at the output, Ta=25 deg C Transient Response Waveforms Transients 50% to 75% load, 5 Vdc Output Transients 75% to 50% load, 5 Vdc Output Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTER 12 Vdc Input 1.2 Vdc - 5.0 Vdc/15 A Output Transient Response Waveforms (continued) Transients 50% to 75% load, 3.3 Vdc Output Transients 50% to 75% load, 2.5 Vdc Output Transients 50% to 75% load, 1.8 Vdc Output Transients 75% to 50% load, 3.3 Vdc Output Transients 75% to 50% load, 2.5 Vdc Output Transients 75% to 50% load, 1.8 Vdc Output Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTER 12 Vdc Input 1.2 Vdc - 5.0 Vdc/15 A Output Transient Response Waveforms (continued) Transients 50% to 75% load, 1.5 Vdc Output Transients 50% to 75% load, 1.25 Vdc Output Transients 50% to 75% load, 1.2 Vdc Output Transients 75% to 50% load, 1.5 Vdc Output Transients 75% to 50% load, 1.25 Vdc Output Transients 75% to 50% load, 1.2 Vdc Output Note: Transient Response at Vin=12 Vdc, di/dt=0.1 A/uS, with external load capacitor 5x10 uF/10 V ceramic capacitor and an 1000 uF/16 V electrolytic at the output, and Ta=25 deg C. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTER 12 Vdc Input 1.2 Vdc - 5.0 Vdc/15 A Output Mechanical Outline Pin Connections Pin 1 2 3 4 5 6 7 8 9 10 11 Function Vout Vout Vout Trim Output Enable Power Good Ground Ground PWRGD_SET Vin Vin RoHS Compliance Complies with the European Directive 2002/95/EC, calling for the elimination of lead and other hazardous substances from electronic products. ©2007 Bel Fuse Inc. Specifications subject to change without notice. 011907 CORPORATE FAR EAST EUROPE Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com Bel Fuse Ltd. 8F/ 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com