BRIGHT LED ELECTRONICS CORP. BL-HZD39T-TRB SINCE 1981 ● Features: 1. Emitted Color : White ●Package Dimensions: 2. Mono-color type. 3. Suitable for all SMT assembly methods. 4. Compatible with infrared and vapor phase reflow solder process. 5. Compatible with automatic placement equipment. 6. This product doesn’t contain restriction Substance, comply ROHS standard. ● Applications: 1. Flash light . 2. Backlighting : LCDs. 3. Status indicators : Consumer & industrial electronics. 4. General use. NOTES: 1.All dimensions are in millimeters. 2.Tolerance is ±0.10mm unless otherwise specified. 3.Specifications are subject to change without notice. 4.LED weight is 0.05g. ● Absolute Maximum Ratings(Ta=25℃) Parameter Symbol Rating Unit Power Dissipation Pd 100 mW Forward Current IF 20 mA Peak Forward Current *1 IFP 100 mA Reverse Voltage VR 5 V Operating Temperature Topr -25℃~80℃ ℃ Storage Temperature Tstg -30℃~85℃ ℃ Soldering Temperature Tsol See Page5 - *1 Condition for IFP is pulse of 1/10 duty and 3msec width. Note: The values are based on 1-die performance. Ver.1.0 Page 1 of 9 BRIGHT LED ELECTRONICS CORP. BL-HZD39T-TRB SINCE 1981 ● Electrical and optical characteristics(Ta=25℃) Parameter Symbol Condition Min. Typ. Forward Voltage*1 VF IF =20mA - 3.4 3.8 V Luminous Intensity*2 Iv IF =20mA 2.0 3.0 - cd Reverse Current*1 IR VR=5V - - 1 µA IF =20mA - 55 - deg 0.26 0.30 0.32 0.26 0.30 0.32 Viewing Angle*2 2θ1/2 x Chromaticity Coordinates IF =20mA y Max. Unit - *1 The values are based on 1-die performance. *2 The values are based on 2-dice performance ● Typical Electro-Optical Characteristics Curves Fig.2 VF-Ta Characteristics Fig.1 IF-VF Characteristics 1000 4.0 3.6 VF(v) IF (mA)-1die 3.8 100 20 10 IF=20mA 3.4 3.2 5 3.0 1 2.5 3.0 4.0 3.5 5.0 4.5 -20 0 20 VF (V) 60 80 100 Fig.4 IV-Ta Characteristics Fig.3 IV-IF Characteristics 200 10 100 IV (in%) 100 Relative IV-2dice 40 Ta( C ) 1.0 50 0.5 0.1 0.5 1 5 10 20 50 -20 0 20 40 60 80 100 Ta( C) IF(mA)-1die Fig.6 Radiation diagram Fig.5 Max-Ta Characteristics 0 10 20 30 RELATIVE RADIANT INTENSITY 30 IF MAX(mA)-1die 25 20 15 10 5 0 -20 0 20 40 60 80 100 40 1.0 0.9 50 0.8 60 70 0.7 80 90 0.5 0.3 0.1 0.2 0.4 0.6 Ta( C) Ver.1.0 Page 2 of 9 BRIGHT LED ELECTRONICS CORP. BL-HZD39T-TRB SINCE 1981 ● Tapping and packaging specifications(Units: mm) 17.2±1.2 USER DIRECTION OF FEED 1.7±0.1 3.6 END 4.0 ± 0.1 1.5±0.1 4.0 ± 0.1 13.0± 0.5 71.0±1 12.0 ± 0.3 (4) (3) 1.75 ± 0.1 5.5 ± 0.05 3.6 (2) (1) TRAILER LEADER 0.3 FIXING TAPE 2.0±0.05 NOTE: 1500 pcs PER REEL ●Package Method:(unit:mm) 12 bag/box 1500 pcs/reel 185 Bar Code Label 245 200 220 Aluminum Foil Bag 220 645 6 box/carton 210 470 Ver.1.0 Page 3 of 9 179±1 START BRIGHT LED ELECTRONICS CORP. BL-HZD39T-TRB SINCE 1981 ● Bin Limits I n t e n s i t y B i n L i m i ts ( A t 2 0 m A ) BIN CODE Min. (cd) Z 2 V F B i n L i m i ts ( A t 2 0 m A ) BIN CODE ● B IN: x x Min.(v) Max. (cd) - Max.(v) H 3.0 3.2 J 3.2 3.4 K 3.4 3.6 L 3.6 3.8 x VF BIN CODE Color BIN CODE Intensity BIN CODE Ver1.0 Page 4 of 9 BRIGHT LED ELECTRONICS CORP. BL-HZD39T-TRB SINCE 1981 C o l o r B i n L i m i ts ( A t 2 0 m A ) Chromaticity Coordinates y x C o l o r B i n L i m i ts ( A t 2 0 m A ) BIN x 0.28 F-1 y 0.26 x 0.28 F-2 y 0.28 x 0.30 F-3 y 0.26 x 0.30 F-4 y 0.28 x 0.30 F-5 y 0.30 x 0.32 F-6 y 0.28 x 0.32 F-7 y 0.30 Chromaticity Coordinates 0.26 0.26 0.26 0.28 0.28 0.26 0.28 0.28 0.28 0.30 0.30 0.28 0.30 0.30 0.26 0.28 0.26 0.30 0.28 0.28 0.28 0.30 0.28 0.32 0.30 0.30 0.30 0.32 0.28 0.28 0.28 0.30 0.30 0.28 0.30 0.30 0.30 0.32 0.32 0.30 0.32 0.32 Ver.1.0 Page 5 of 9 BRIGHT LED ELECTRONICS CORP. BL-HZD39T-TRB SINCE 1981 ● Reliability Test Classification Test Item Reference Standard Operation Life MIL-STD-750:1026 MIL-STD-883:1005 JIS-C-7021 :B-1 High Temperature MIL-STD-202:103B High Humidity JIS-C-7021 :B-11 Endurance Storage Test High MIL-STD-883:1008 Temperature JIS-C-7021 :B-10 Storage Low Temperature JIS-C-7021 :B-12 Storage Temperature MIL-STD-202:107D Cycling MIL-STD-750:1051 MIL-STD-883:1010 JIS-C-7021 :A-4 Thermal Shock MIL-STD-202:107D Environmental MIL-STD-750:1051 Test MIL-STD-883:1011 Solder MIL-STD-202:201A Resistance MIL-STD-750:2031 JIS-C-7021 :A-1 Test Conditions Connect with a power IF=20mA Ta=Under room temperature Test time=1,000hrs Ta=+65℃±5℃ RH=90%-95% Test time=240hrs Result 0/20 0/20 High Ta=+85℃±5℃ Test time=1,000hrs 0/20 Low Ta=-35℃±5℃ Test time=1,000hrs 0/20 -35℃ ~ +25℃ ~ +85℃ ~ +25℃ 60min 20min 60min 20min Test Time=5cycle -35℃±5℃ ~+85℃±5℃ 20min 20min Test Time=10cycle Preheating: 140℃-160℃,within 2 minutes. Operation heating: 235℃(Max.), within 10seconds. (Max.) 0/20 0/20 0/20 ● Judgment criteria of failure for the reliability Measuring items Forward voltage Reverse current Luminous intensity Note: Symbol VF ( V) IR(uA) Iv ( mcd ) Measuring conditions IF=20mA VR=5V IF=20mA 1.U means the upper limit of specified characteristics. Judgement criteria for failure Over Ux1.2 Over Ux2 Below SX0.5 S means initial value. 2.Measurment shall be taken between 2 hours and after the test pieces have been returned to normal ambient conditions after completion of each test. Ver1.0 Page 6 of 9 BRIGHT LED ELECTRONICS CORP. BL-HZD39T-TRB SINCE 1981 ● Soldering : 1. Manual Of Soldering The temperature of the iron tip should not be higher than 300℃(572℉) and Soldering within 3 seconds per solder-land is to be observed. 2. Reflow Soldering Preheating : 140℃~160℃±5℃,within 2 minutes. Operation heating : 260℃(Max.) within 10 seconds.(Max) Gradual Cooling (Avoid quenching). 10 SEC. MAX. Temperature 260℃ MAX. 140~160℃ 4℃ /SEC. MAX. 4℃ /SEC. MAX. OVER 2 MIN. Time 3. DIP soldering (Wave Soldering) : Preheating : 120℃~150℃,within 120~180 sec. Operation heating : 245℃±5℃ within 5 sec.260℃ (Max) Gradual Cooling (Avoid quenching). Temperature Soldering heat Max. 260 ℃ 245 ±5℃ within 5 sec. 120~150℃ Preheat 120~180 sec. Time ● Handling : Care must be taken not to cause to the epoxy resin portion of BRIGHT LEDs while it is exposed to high temperature. Care must be taken not rub the epoxy resin portion of BRIGHT LEDs with hard or sharp article such as the sand blast and the metal hook. Ver.1.0 Page 7 of 9 BRIGHT LED ELECTRONICS CORP. BL-HZD39T-TRB SINCE 1981 ● Notes for designing: Care must be taken to provide the current limiting resistor in the circuit so as to drive the BRIGHT LEDs within the rated figures. Also, caution should be taken not to overload BRIGHT LEDs with instantaneous voltage at the turning ON and OFF of the circuit. When using the pulse drive care must be taken to keep the average current within the rated figures. Also, the circuit should be designed so as be subjected to reverse voltage when turning off the BRIGHT LEDs. ● Storage: In order to avoid the absorption of moisture, it is recommended to solder BRIGHT LEDs as soon as possible after unpacking the sealed envelope. If the envelope is still packed, to store it in the environment as following: (1) Temperature : 5℃-30℃(41℉)Humidity : RH 60﹪Max. (2) After this bag is opened, devices that will be applied to infrared reflow, vapor-phase reflow, or equivalent soldering process must be: a. Completed within 24 hours. b. Stored at less than 30% RH. (3) Devices require baking before mounting, if: (2) a or (2) b is not met. (4) If baking is required, devices must be baked under below conditions: 12 hours at 60℃±3℃. ● Package and Label of Products: (1) Package: Products are packed in one bag of 1500 pcs (one taping reel) and a label is attached on each bag. (2) Label: BRIGHT LED LOGO Part No. Quantity BIN. Sealing Date x xx xx Year Month xx Day Manufacture Location Ver1.0 Page 8 of 9 BRIGHT LED ELECTRONICS CORP. BL-HZD39T-TRB SINCE 1981 ● Application circuit: When using multiple LEDs,it is required to connect a current limiting resistor on each path the current flows to the LEDs. (ex-1) (ex-2) R R R Ver1.0 Page 9 of 9