page 1 of 5 date 3/6/2008 DESCRIPTION: magnetic buzzer PART NUMBER: CCV-084B16 SPECIFICATONS rated voltage operating voltage mean current coil resistance sound output rated frequency operating tempurature storage tempurature dimensions weight material terminal RoHS 3.6 Vo-p 2.5 ~ 4.5 Vo-p 110 mA max. 16 ± 2.4 Ω 85 db min. (90 TYP) 2730 Hz -30 ~ +70° C -40 ~ +85° C Ø9.0 x H2.5 mm 0.6 g max. PPS SMD type/Au plating yes at 3.6 Vo-p, sqaure wave, 2730 Khz at 10 cm/3.6 Vo-p, sqaure wave, 2730 Khz APPEARANCE DRAWING tolerance: ±0.3 units: mm 2.5 0.098 0.5 0.020 (TYP) 10.4 0.409 30° 2.3 0.091 (2 PLCS) 1.5 0.059 (2 PLCS) _ + 10.5 0.413 30° 6.0 0.236 5.2 0.205 11.4 0.449 30° 4.0 0.157 0.9 0.035 0.5 0.020 3.3X2.5 (2 PLCS) sound port 30° 9.0 0.354 6.0 0.236 0.8 0.031 (2 PLCS) PCB LAYOUT TOP VIEW 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383 PART NUMBER: CCV-084B16 DESCRIPTION: magnetic buzzer FREQUENCY RESPONSE CURVE MEASUREMENT METHOD 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383 page 2 of 5 date 3/6/2008 page 3 of 5 date 3/6/2008 DESCRIPTION: magnetic buzzer PART NUMBER: CCV-084B16 MECHANICAL CHARACTERISTICS item solderability soldering heat resistance terminal mechanical strength vibration drop test test condition evaluation standard Lead terminals are immersed in solder bath 95% min. of the lead terminals of 270 ±5°C for 3 ±1 seconds. will be wet with solder. The product is followed the reflow temperature No interference in operation. curve to test its reflow thermo stability. Lead pads shall be soldered on the pc board, and a force of 9.8N (1.0kg) shall be applied No damage or cutting off. behind the part for 10 seconds. The buzzer shall be measured after applying The value of oscillation a vibration amplitude of 1.5 mm with 10 to frequency/current consumption 55 Hz band of vibration frequency to each of should be ±10% of the initial the 3 perpendicular directions for 2 hours. measurements. The SPL should The part will be dropped from a height of be within ±10dB compared with 75 cm onto a 40 mm thick wooden board 3 the initial measurement. times in 3 axes (X, Y, Z) for a total of 9 drops. ENVIRONMENT TEST item high temp. test low temp. test thermal shock temp. cycle test test condition After being placed in a chamber at +85°C for 96 hours. After being placed in a chamber at -40°C for 96 hours. The part shall be subjected to 10 cycles. One cycle will consist of: The part shall be subjected to 5 cycles. One cycle will consist of: evaluation standard The buzzer will be measured after being placed at +25°C for 4 hours. The value of the oscillation frequency/current consumption should be ±10% compared to the initial measurements. The SPL should be within ±10dB compared to the initial measurements. 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383 page 4 of 5 date 3/6/2008 DESCRIPTION: magnetic buzzer PART NUMBER: CCV-084B16 RELIABILITY TEST item operating (life test) test condition 1. Continuous life test: The part will be subjected to 72 hours of continuous operation at +55°C with rated voltage applied. 2. Intermittent life test: A duty cycle of 1 minute on, 1 minutes off, a minimum of 10,000 times at room temp (+25 ±10°C) with rated voltage applied. evaluation standard The buzzer will be measured after being placed at +25°C for 4 hours. The value of the oscillation frequency/current consumption should be ±10% compared to the initial measurements. The SPL should be within ±10dB compared to the initial measurements. TEST CONDITIONS standard test condition judgement test condition a) tempurature: +5 ~ +35°C a) tempurature: +25 ±2°C b) humidity: 45 - 85% b) humidity: 60 - 70% c) pressure: 860-1060 mbar c) pressure: 860-1060 mbar TEMPERATURE REFLOW 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383 PART NUMBER: CCV-084B16 DESCRIPTION: magnetic buzzer PACKAGING 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383 page 5 of 5 date 3/6/2008