CURRENT 1.0 Ampere VOLTAGE 50 to 1000 Volts HER101G THRU HER108G Features · Plastic package has Underwriters Laboratory Flammability Classification 94V-0 · Low forward voltage drop · High current capability · High reliability · Low power loss, high effciency · Glass passivated junction · High speed switching · Low leakage DO-41 0.107(2.7) 0.080(2.0) DIA. 1.0(25.4) MIN. 0.205(5.2) 0.166(4.2) Mechanical Data · Case : JEDEC DO-41 molded plastic body · Epoxy : UL94V-0 rate flame retardant · Lead : Plated axial lead solderable per MIL-STR-750, method 2026 · Polarity : Color band denotes cathode end · Mounting Position : Any · Weight : 0.012 ounce, 0.33 gram 1.0(25.4) MIN. 0.034(0.9) 0.028(0.7) DIA. Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols HER HER HER HER HER HER HER HER 101G 102G 103G 104G 105G 106G 107G 108G Units Maximum recurrent peak reverse voltage VRRM 50 100 200 300 400 600 800 1000 Volts Maximum RMS voltage VRMS 35 70 140 210 280 420 560 700 Volts Maximum DC blocking voltage VDC 50 100 200 300 400 600 800 1000 Volts Maximum average forward rectified current 0.375"(9.5mm) lead length @ at TA=55℃ I(AV) 1.0 Amp Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) IFSM 30.0 Amps Maximum instantaneous forward voltage at 1.0A VF 1.0 1.3 Maximum DC reverse current at rated DC blocking voltage TA=25℃ Maximum DC reverse current at rated DC blocking voltage TA=125℃ 1.7 Volts 5.0 μA IR 100 Maximum reverse recovery time (Note 1) Trr 50 75 ns Typical junction capacitance (Note 2) CJ 20 15 pF Operating junction and storage temperature range TJ TSTG Notes: (1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A. (2) Measured at 1MHz and applied reverse voltage of 4.0 Volts. -65 to +150 ℃ RATINGS AND CHARACTERISTIC CURVES HER101G THRU HER108G 50W NON INDUCTIVE (+) 10W NON INDUCTIVE D.U.T. ) 1W NON INDUCTIVE 0 PULSE GENERATOR (NOTE2) 50Vdc (APPROX) ( Trr +0.5A -0.25A OSCILLOSCOPE (NOTE1) -1.0A NOTES : 1.Rise Time=7ns max. input impedance=1 megohm 22pF 2.Rise Time=10ns max. source impedance = 50 ohms AVERAGE FORWARD CURRENT(A) FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE FIG.1-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 2.0 SINGLE PHASE HALF WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD 0.375"(9.5mm) LEAD LENGTH 1.0 1cm 0 0 SET TIME BASE FOR 10/20 ns/cm 25 50 75 100 125 150 175 INSTANTANEOUS FORWARD CURRENT(AMPERES) AMBIENT TEMPERATURE ( ℃) FIG.3-TYPICAL FORWARD CHARACTERISTICS FIG.4-TYPICAL REVERSE CHARACTERISTICS 10 6G 10 -H ER R1 07 GHE HE 0.1 R1 08 G 05 G HE R1 HE R1 01 G -H ER 10 4G 1 INSTANTANEOUS REVERSE CURRENT (mA) 1000 0.01 TA=125℃ 100 10 TA=25℃ 1.0 TA=25℃ PULSE WIDTH=300mS 0.1 1% DUTY CYCLE 0.001 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 0 20 1.8 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE (%) INSTANTANEOUS FORWARD VOLTAGE (VOLTS) FIG.5-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT FIG6-TYPICAL JUNCTION CAPACITANCE 40 70 JUNCTION CAPACITANCE(pF) PEAK FORWARD SURGE CURRENT(AMPERES) 35 TA=25℃ 8.3m SINGLE HALF SINE WAVE (JEDEC Method) 30 25 20 15 10 5 1 5 10 NUMBER OF CYCLES AT 60Hz 50 100 60 50 40 30 TJ=25℃ HER101G-HER106G 20 10 HER107G-HER108G 0 0.1 0.5 1 2 5 10 20 REVERSE VOLTAGE. (V) 50 100 200 1000