FEATURES High efficiency: 86% @ 1.5V/8A, 3.3V/6A Low profile: 57.9 x 36.8 x 8.5mm (2.28”×1.45”×0.33”) Fixed frequency operation Flexible current allocation on each output Low voltage output (O/P 1) starts up first Industry standard pin out Input UVLO, Output OCP, OVP, OTP No minimum load required 2:1 input voltage range Basic insulation ISO 9001, TL 9000, ISO 14001, QS 9000, OHSAS 18001 certified manufacturing facility UL/cUL 60950 (US & Canada) recognized, and TUV (EN60950) certified CE mark meets 73/23/EEC and 93/68/EEC directives Delphi Series Q48DV, 40W Quarter Brick, Dual Output DC/DC Power Modules The Delphi Series Q48DV Quarter Brick, 48V input, dual output, isolated DC/DC converters are the latest offering from a world leader in power system and technology and manufacturing -- Delta Electronics, Inc. This product family provides dual regulated outputs with a flexible combination of output current and power up to 40W in a very cost effective industry standard footprint. With creative design technology and optimization of component placement, these converters possess outstanding electrical and thermal performance, as well as extremely high reliability under highly stressful operating conditions. All models are fully protected from abnormal input/output voltage, current, and temperature conditions. The Delphi Series Q48DV converters meet all safety requirements with basic insulation. OPTIONS Positive On/Off logic Short pin lengths Heatsink available for extended operation APPLICATIONS Telecom/DataCom Wireless Networks Optical Network Equipment Server and Data Storage Industrial/Test Equipment DATASHEET DS_Q48DV1R533_07172006 TECHNICAL SPECIFICATIONS (T =25°C, airflow rate=300 LFM, V A PARAMETER in =48Vdc, nominal Vout unless otherwise noted.) NOTES and CONDITIONS Q48DV1R533NRFA Min. ABSOLUTE MAXIMUM RATINGS Input Voltage Continuous Transient (100ms) Operating Temperature Storage Temperature Input/Output Isolation Voltage INPUT CHARACTERISTICS Operating Input Voltage Input Under-Voltage Lockout Turn-On Voltage Threshold Turn-Off Voltage Threshold Lockout Hysteresis Voltage Maximum Input Current No-Load Input Current Off Converter Input Current Inrush Current(I2t) Input Reflected-Ripple Current Input Voltage Ripple Rejection OUTPUT CHARACTERISTICS Output Voltage Set Point <100ms Refer to Figure 27 for measuring point -40 -55 1500 <1 minute Units 80 100 115 125 Vdc Vdc °C °C Vdc 48 75 Vdc 33 31 1 34 32 2 35 33 3 1.3 60 10 Vdc Vdc Vdc A mA mA A2s mA dB 40 5 0.015 5 66 Vout 1 Vout 2 Max. 36 P-P thru 12µH inductor, 5Hz to 20MHz 120Hz Vin=48V, Io=Io.max, Tc=25℃ Typ. 1.500 3.300 20 1.540 3.330 1.560 3.360 Vdc ±5 ±15 mV ±3 ±10 mV ±5 ±15 ±15 ±50 1.600 3.445 mV mV Output Voltage Regulation Over Load Io1=Io, min to Io, max, Io2=0A Io2=Io, min to Io, max, Io1=0A Over Line Vin=36V to 75V,Io1=Io2=full load Cross Regulation Over Temperature Total Output Voltage Range Output Voltage Ripple and Noise Worse Case Tc=-40℃ to 115℃ Over all load, line and temperature Vout 1 Vout2 1.479 3.225 Io1, Io2 Full Load, 1µF ceramic, 10µF tantalum RMS Io1, Io2 Full Load, 1µF ceramic, 10µF tantalum Operating Output Current Range Output DC Current-Limit Inception Vout 1 Vout 2 Vout 1 Vout 2 Vout 1 Vout 2 Vout 1 Vout 2 30 30 12 12 0 0 10 8 48V, 10µF Tan & 1µF Ceramic load cap, 0.1A/µs Vout 1 Vout 2 Vout 1 Positive Step Change in Output Current Iout1and Iout2 from 50% Io, max to 75% Io, max Negative Step Change in Output Current Iout2 and Iout1 from 75% Io, max to 50% Io, max Vout 2 Cross dynamic Settling Time (within 1% Vout nominal) Turn-On Transient Delay Time, From On/Off Control Delay Time, From Input Start-up Time, From On/Off Control Start-up Time, From Input Maximum Output Capacitance EFFICIENCY 100% Load 60% Load ISOLATION CHARACTERISTICS Input to Output Isolation Resistance Isolation Capacitance FEATURE CHARACTERISTICS Switching Frequency ON/OFF Control, (Logic Low-Module ON) Logic Low Logic High ON/OFF Current Leakage Current Output Voltage Trim Range Output Boltage Remoote Sense Range Output Over-Voltage Protection GENERAL SPECIFICATIONS MTBF Weight Over-Temperature Shutdown DS_Q48DV1R533_07172006 V 5Hz to 20MHz bandwidth Peak-to-Peak DYNAMIC CHARACTERISTICS Output Voltage Current Transient Vout 1 Vout 2 Vout 1 Vout 2 Full load; 5% overshoot of Vout at startup Von/off at Ion/off=1.0mA Von/off at Ion/off=0.0 µA Ion/off at Von/off=0.0V Logic High, Von/off=15V Just trim Vout1, Pout ≦ max rated power No Remote Sense Function Over full temp range; %of nominal Vout Io=80% of Io, max; Ta=25°C Refer to Figure 27 for measuring point mV A 100 100 100 100 100 100 mV us 10 10 10 10 ms ms ms ms mV mV 10000 5000 µF 86 86.5 % % 2000 Vdc MΩ pF 300 kHz 1500 10 0 -20 120 mV A Vout 1 Vout 2 Iout1, Iout2 full load, 48vdc Vin Iout1, Iout2 60% of full load, 48vdc Vin <1 minute 50 50 20 20 8 6 135 3.45 25 117 0.8 18 1 2 +10 V V mA mA % 150 % M hours grams °C 2 ELECTRICAL CHARACTERISTICS CURVES Figure 1: Efficiency vs. load current Iout2 for minimum, nominal, and maximum input voltage at 25°C, for Iout1=4A. Figure 2: Efficiency vs. load current Iout1 for minimum, nominal, and maximum input voltage at 25°C, for Iout2=3A Figure 3: Efficiency vs. load current Iout1 and Iout2 for minimum, nominal, and maximum input voltage at 25°C, for Iout1=Iout2 Figure 4: Power dissipation vs. load current for minimum, nominal, and maximum input voltage at 25°C. for Iout1=Iout2 DS_Q48DV1R533_07172006 3 ELECTRICAL CHARACTERISTICS CURVES Figure 5: Turn-on transient at zero load current (10ms/div). Vin=48V. Negative logic turn on. Top Trace: Vout; 1V/div; Bottom Trace: ON/OFF input: 5V/div Figure 6: Turn-on transient at full rated load current (resistive load) (10 ms/div). Vin=48V. Negative logic turn on. Top Trace: Vout; 1V/div; Bottom Trace: ON/OFF input: 5V/div Figure 7: Turn-on transient at zero load current (10ms/div). Vin=48V. Positive logic turns on. Top Trace: Vout; 1V/div; Bottom Trace: ON/OFF input: 5V/div Figure 8: Turn-on transient at full load current (10ms/div). Vin=48V. Positive logic turns on. Top Trace: Vout; 1V/div; Bottom Trace: ON/OFF input: 5V/div DS_Q48DV1R533_07172006 4 ELECTRICAL CHARACTERISTICS CURVES Figure 9: Typical full load input characteristics at room temperature Figure 10: Output voltage response to step-change in load current Iout2 (75%-50%-75% of Io, max; di/dt = 0.1A/µs) at Iout1=0A. Load cap: 10µF, tantalum capacitor and 1µF ceramic capacitor. Ch1=Vout2 (100mV/div), Ch2=Iout2 (5A/div), Scope measurement should be made using a BNC cable (length shorter than 20 inches). Position the load between 51 mm to 76 mm (2 inches to 3 inches) from the module. Figure 11: Output voltage response to step-change in load current Iout1 (75%-50%-75% of Io, max; di/dt = 0.1A/µs) at Iout2=0. Load cap: 10µF, tantalum capacitor and 1µF ceramic capacitor. Ch1=Vout1 (100mV/div), Ch2=Iout1 (5A/div),Scope measurement should be made using a BNC cable (length shorter than 20 inches). Position the load between 51 mm to 76 mm (2 inches to 3 inches) from the module. Figure 12: Output voltage response to step-change in load current Iout2 and Iout1 (75%-50%-75% of Io, max; di/dt = 0.1A/µs). Load cap: 10µF, tantalum capacitor and 1µF ceramic capacitor. Ch1=Vout1 (100mV/div), Ch2=Iout1 (5A/div), Ch3=Vout2 (100mV/div), Ch4=Iout2 (5A/div) Scope measurement should be made using a BNC cable (length shorter than 20 inches). Position the load between 51 mm to 76 mm (2 inches to 3 inches) from the module. DS_Q48DV1R533_07172006 5 ELECTRICAL CHARACTERISTICS CURVES Figure 13: Output voltage response to step-change in load current Iout2 (75%-50%-75% of Io, max; di/dt = 2.5A/µs) at Iout1=0. Load cap: 470µF, 35mΩ ESR solid electrolytic capacitor and 1µF ceramic capacitor. Ch1=Vout2 (100mV/div), Ch2=Iout2 (5A/div), Scope measurement should be made using a BNC cable (length shorter than 20 inches). Position the load between 51 mm to 76 mm (2 inches to 3 inches) from the module. Figure 14: Output voltage response to step-change in load current Iout1 (75%-50%-75% of Io, max; di/dt = 2.5A/µs) at Iout2=0A, Load cap: 470µF, 35mΩ ESR solid electrolytic capacitor and 1µF ceramic capacitor. Ch1=Vout1 (100mV/div), Ch2=Iout1 (5A/div), Scope measurement should be made using a BNC cable (length shorter than 20 inches). Position the load between 51 mm to 76 mm (2 inches to 3 inches) from the module. Figure 15: Output voltage response to step-change in load current Iout2 and Iout1 (75%-50%-75% of Io, max; di/dt = 2.5A/µs). Load cap: 470µF, 35mΩ ESR solid electrolytic capacitor and 1µF ceramic capacitor. Ch1=Vout1 (100mV/div), Ch2=Iout1 (5A/div), Ch3=Vout2 (100mV/div), Ch4=Iout2 (5A/div) Scope measurement should be made using a BNC cable (length shorter than 20 inches). Position the load between 51 mm to 76 mm (2 inches to 3 inches) from the module. Figure 16: Test set-up diagram showing measurement points for Input Terminal Ripple Current and Input Reflected Ripple Current. Note: Measured input reflected-ripple current with a simulated source Inductance (LTEST) of 12 µH. Capacitor Cs offset possible battery impedance. Measure current as shown above. DS_Q48DV1R533_07172006 6 ELECTRICAL CHARACTERISTICS CURVES Figure 17: Input Terminal Ripple Current-ic, at full rated output current and nominal input voltage with 12µH source impedance and 33µF electrolytic capacitor (500 mA/div, 2us/div). Figure 18: Input reflected ripple current-is, through a 12µH source inductor at nominal input voltage and rated load current (20 mA/div, 2us/div). Copper Strip Vo(+) 10u 1u SCOPE RESISTIV LOAD Vo(-) Figure 19: Output voltage noise and ripple measurement test setup DS_Q48DV1R533_07172006 Figure 20: Output voltage ripple at nominal input voltage and rated load current (Iout1=Iout2=Full)(20 mV/div, 1us/div). Top trace: Vout2 (50mV/div), Bottom trace:Vout1(50mV/div) Load capacitance: 1µF ceramic capacitor and 10µF tantalum capacitor. Bandwidth: 20 MHz. Scope measurements should be made using a BNC cable (length shorter than 20 inches). Position the load between 51 mm to 76 mm (2 inches to 3 inches) from the module. 7 ELECTRICAL CHARACTERISTICS CURVES Figure 21: Output voltage vs. load current Iout1 showing typical current limit curves and converter shutdown points. DS_Q48DV1R533_07172006 Figure 22: Output voltage vs. load current Iout2 showing typical current limit curves and converter shutdown points. 8 DESIGN CONSIDERATIONS Input Source Impedance The impedance of the input source connecting to the DC/DC power modules will interact with the modules and affect the stability. A low ac-impedance input source is recommended. If the source inductance is more than a few µH, we advise adding a 10 to 100 µF electrolytic capacitor (ESR < 0.7 Ω at 100 kHz) mounted close to the input of the module to improve the stability. Do not ground one of the input pins without grounding one of the output pins. This connection may allow a non-SELV voltage to appear between the output pin and ground. Layout and EMC Considerations This power module is not internally fused. To achieve optimum safety and system protection, an input line fuse is highly recommended. The safety agencies require a normal-blow fuse with 7A maximum rating to be installed in the ungrounded lead. A lower rated fuse can be used based on the maximum inrush transient energy and maximum input current. Delta’s DC/DC power modules are designed to operate in a wide variety of systems and applications. For design assistance with EMC compliance and related PWB layout issues, please contact Delta’s technical support team. An external input filter module is available for easier EMC compliance design. The power module has extra-low voltage (ELV) outputs when all inputs are ELV. Soldering and Cleaning Considerations Safety Considerations The power module must be installed in compliance with the spacing and separation requirements of the end-user’s safety agency standard, i.e., UL60950, CAN/CSA-C22.2 No. 60950-00 and EN60950:2000 and IEC60950-1999, if the system in which the power module is to be used must meet safety agency requirements. When the input source is 60 Vdc or below, the power module meets SELV (safety extra-low voltage) requirements. If the input source is a hazardous voltage which is greater than 60 Vdc and less than or equal to 75 Vdc, for the module’s output to meet SELV requirements, all of the following must be met: Post solder cleaning is usually the final board assembly process before the board or system undergoes electrical testing. Inadequate cleaning and/or drying may lower the reliability of a power module and severely affect the finished circuit board assembly test. Adequate cleaning and/or drying is especially important for un-encapsulated and/or open frame type power modules. For assistance on appropriate soldering and cleaning procedures, please contact Delta’s technical support team. The input source must be insulated from any hazardous voltages, including the ac mains, with reinforced insulation. One Vi pin and one Vo pin are grounded, or all the input and output pins are kept floating. The input terminals of the module are not operator accessible. If the metal baseplate is grounded the output must be also grounded. A SELV reliability test is conducted on the system where the module is used to ensure that under a single fault, hazardous voltage does not appear at the module’s output. DS_Q48DV1R533_07172006 9 FEATURES DESCRIPTIONS Over-Current Protection The modules include an internal output over-current protection circuit, which will endure current limiting for an unlimited duration during output overload. If the output current exceeds the OCP set point, the modules will automatically shut down (hiccup mode). The modules will try to restart after shutdown. If the overload condition still exists, the module will shut down again. This restart trial will continue until the overload condition is corrected. Over-Voltage Protection Figure 23: Remote on/off implementation The modules include an internal output over-voltage protection circuit, which monitors the voltage on the output terminals. If this voltage exceeds the over-voltage set point, the module will shut down and latch off. Output Voltage Adjustment (TRIM) The over-voltage latch of this module will be reset by either cycling the input power or by toggling the on/off signal for one second. To increase or decrease the output voltage (Vout1) set point, the modules may be connected with an external resistor between the TRIM pin and either Vout1(+) or RTN. The Vout2 cannot be trimmed. The TRIM pin should be left open if this feature is not used. Over-Temperature Protection The over-temperature protection consists of circuitry that provides protection from thermal damage. If the temperature exceeds the over-temperature threshold the module will shut down. The module will try to restart after shutdown. If the over-temperature condition still exists during restart, the module will shut down again. This restart trial will continue until the temperature is within specification. Remote On/Off The remote on/off feature on the module can be either negative or positive logic. Negative logic turns the module on during a logic low and off during a logic high. Positive logic turns the modules on during a logic high and off during a logic low. Figure 24: Circuit configuration for trim-up (increase output voltage) If the external resistor is connected between the TRIM and Vout1(+) pin, the output voltage (Vout1) set point increases (Fig. 24). Remote on/off can be controlled by an external switch between the on/off terminal and the Vi(-) terminal. The switch can be an open collector or open drain. For negative logic if the remote on/off feature is not used, please short the on/off pin to Vi(-). For positive logic if the remote on/off feature is not used, please leave the on/off pin floating. DS_Q48DV1R533_07172006 10 FEATURES DESCRIPTIONS (CON.) Figure 25: Circuit configuration for trim-down (decrease output voltage) If the external resistor is connected between the TRIM and RTN, the output voltage (Vout1) set point decreases (Fig.25). Refer to the table below for the external resistor values. Trim Resistor Trim Resistor (Vout Increase) (Vout Decrease) Vout1 Rtrim-up [KΩ] Vout1 Rtrim-down [KΩ] 1.5 Open 1.5 Open 1.6 86.6 1.4 24.9 1.7 34.8 1.3 10.7 1.8 15.8 1.2 4.87 1.9 10.2 1.1 2.21 2 6.98 1.0 0 The output voltage can be increased by the trim pin, When using trim; the output voltage of the module is usually increased, which increases the power output of the module with the same output current. Care should be taken to ensure that the maximum output power of the module remains at or below the maximum rated power. DS_Q48DV1R533_07172006 11 THERMAL CONSIDERATIONS THERMAL CURVES Thermal management is an important part of the system design. To ensure proper, reliable operation, sufficient cooling of the power module is needed over the entire temperature range of the module. Convection cooling is usually the dominant mode of heat transfer. Hence, the choice of equipment to characterize the thermal performance of the power module is a wind tunnel. Thermal Testing Setup Delta’s DC/DC power modules are characterized in heated vertical wind tunnels that simulate the thermal environments encountered in most electronics equipment. This type of equipment commonly uses vertically mounted circuit cards in cabinet racks in which the power modules are mounted. The following figure shows the wind tunnel characterization setup. The power module is mounted on a test PWB and is vertically positioned within the wind tunnel. The space between the neighboring PWB and the top of the power module is constantly kept at 6.35mm (0.25’’). Figure 27: Hot spot location * The allowed maximum hot spot temperature is defined at 115℃ Q48DV1R533(Standard) Output Load vs. Ambient Temperature and Air Velocity @Vin = 48V (Transverse Orientation) Output Load(%) 110% 600LFM 100% 500LFM 90% 400LFM Natural Convection 80% 70% 60% Thermal Derating 100LFM 50% Heat can be removed by increasing airflow over the module. The module’s hottest spot is less than 115°C. To enhance system reliability, the power module should always be operated below the maximum operating temperature. If the temperature exceeds the maximum module temperature, reliability of the unit may be affected. PWB FACING PWB 200LFM 40% 300LFM 30% 20% 10% 0% 55 60 65 70 75 80 85 90 95 100 105 110 Ambient Temperature (℃) Figure 28: Output current vs. ambient temperature and air velocity (Vin = 48V) MODULE AIR VELOCITY AND AMBIENT TEMPERATURE MEASURED BELOW THE MODULE 50.8 (2.0”) AIR FLOW 12.7 (0.5”) Note: Wind Tunnel Test Setup Figure Dimensions are in millimeters and (Inche Figure 26: Wind tunnel test setup figure DS_Q48DV1R533_07172006 12 MECHANICAL DRAWING Pin No. 1 2 3 4 5 6 7 Name Function +Vin ON/OFF -Vin +Vout1 Output RTN TRIM +Vout2 Positive input voltage Remote ON/OFF Negative input voltage Positive output voltage1 Power Ground (Vout1 and Vout2) Output voltage trim Positive output voltage2 Notes: 1 2 Pins 1-7 are 1.50mm (0.060”) diameter All pins are copper with Tin Plating DS_Q48DV1R533_07172006 13 PART NUMBERING SYSTEM Q 48 D V Product Type Input Voltage Number of Outputs Product Series Q - Quarter Brick 48V 1R5 D - Dual output V - Value line 33 N R Output Voltage 1 Output Voltage 2 ON/OFF Logic Pin Length 1R0 - 1.0V 1R2 - 1.2V 1R5 - 1.5V 1R8 - 1.8V 2R5 - 2.5V 33 - 3.3V N - Negative P - Positive F A Option Code R - 0.150” F- RoHS 6/6 A - Standard N - 0.145” (Lead Free) functions K - 0.110” MODEL LIST MODEL NAME OUTPUT * INPUT EFF @ Full Load Q48DV1R033NRFA 36V~75V 1.1A 1.0V/10A 3.3V/10A 85.5% Q48DV1R233NRFA 36V~75V 1.2A 1.2V/10A 3.3V/10A 86.0% Q48DV1R533NRFA 36V~75V 1.3A 1.5V/10A 3.3V/10A 86.0% Q48DV1R833NRFA 36V~75V 1.4A 1.8V/10A 3.3V/10A 86.5% Q48DV2R533NRFA 36V~75V 1.6A 2.5V/10A 3.3V/10A 87.0% * Note: Total output power should not exceed 40 watts, maximum output current for each channel is 10A. CONTACT: www.delta.com.tw/dcdc USA: Telephone: East Coast: (888) 335 8201 West Coast: (888) 335 8208 Fax: (978) 656 3964 Email: [email protected] Europe: Phone: +41 31 998 53 11 Fax: +41 31 998 53 53 Asia & the rest of world: Telephone: +886 3 4526107 ext 6220 Fax: +886 3 4513485 Email: [email protected] Email: [email protected] WARRANTY Delta offers a two (2) year limited warranty. Complete warranty information is listed on our web site or is available upon request from Delta. Information furnished by Delta is believed to be accurate and reliable. However, no responsibility is assumed by Delta for its use, nor for any infringements of patents or other rights of third parties, which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Delta. Delta reserves the right to revise these specifications at any time, without notice. DS_Q48DV1R533_07172006 14