3mm LED CBI® Circuit Board Indicator Bi-level 553-xxxx PART NO. 4.32 [.170] 9.65 [.380] 8.13 [.320] CATHODE ID HIGH EFFICIENCY - LED TYPE 01 553-0111 553-0122 553-0133 553-0177 553-0188 5.08 [.200] 2.54 [.100] 3.68 [.145] CATHODE 2.6 Red/Yel [.102] Cathode for MAX Bicolor RECOMMENDED .508 SQ. [.020] 2.54 [.100] 1.0 [.040] P.C. BOARD LAYOUT .254 [.100] COLOR* Top LED 4.44 [.175] Red Green Yellow Orange Blue³ NEW LOW CURRENT - LED TYPE 02 553-0211 553-0222 553-0233 Red Green Yellow RESISTOR 5 VOLTS - LED TYPE 03 Dimensions in mm [inches] Features 553-0311 553-0322 553-0333 • Multiple CBIs form horizontal LED arrays on 4.45mm (0.175”) center-lines. See page 4-41 and 4-42 for pre-assembled arrays 553-0711 553-0744 Standard Polarity shown in drawing: Cathode right • High Contrast, UL 94 V-0 rated, black housing • Oxygen index: 32% • Polymer content: PBT, 0.343 g • Housing stand-offs facilitate PCB cleaning • Solderability per MIL-STD-202F, method 208F • LEDs are safe for direct viewing per IEC 825-1, EN-60825-1 Tolerance note: As noted, otherwise: • LED Protrusion: ±0.04 mm [±0.016] • CBI Housing: ±0.02mm[±0.008] Red Green Yellow BI-COLOR - LED TYPE 07 Red/Green Yellow/Green NON-DIFFUSED - LED TYPE 22 553-2211 553-2222 553-2233 Red Green Yellow * Top-Bottom LED To order any of the 553-xxxx part numbers with Reverse Polarity (Cathode Left), please add -010 to the part numbers shown above. Custom Combinations • Contact factory for information on custom bi-level arrays and color combinations. PART NUMBER ORDERING CODE 5 5 3 – x x x x – 0 1 0 Series LED Type Top Position Color Reverse Polarity Option 1) Cathode Left ³ ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC SENSITIVE DEVICES Bottom Position Color Color = 0) Blank 1) Red or Red/Green Bi-Color 2) Green 3) Yellow 4) Yellow/Green Bi-Color 7) Orange 8) Blue –010 Ordering Code Suffix required ONLY for Reverse Polarity Option 4-28 Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com 553-xxxx Typical Operating Characteristics (TA=25°C) See LED data sheet for additional information See page 4-70 and 4-71 for Reference Only LED Drive Circuit Examples. See page 4-72 for Pin Out HIGH EFFICIENCY Part Number Color Peak Wavelength nm IV mcd VF Volts Test Current (mA) Viewing Angle 2Θ Θ½ LED Data sheet Page # 553-0111 553-0122 553-0133 Red Green Yellow 650 563 585 10 16 6.3 2 2.1 2.1 10 10 10 45° 45° 45° 521-9427 521-9408 521-9428 4-64 4-64 4-64 553-0177 Orange 600 7 2.2 10 60° 521-9498 4-58 553-0188 LOW CURRENT Blue 428 12 3.5 10 70° 521-9831 4-57 Part Number Color Peak Wavelength nm IV mcd VF Volts Test Current (mA) Viewing Angle 2Θ Θ½ LED Data sheet Page # 553-0211 553-0222 553-0233 Red Green Yellow 635 565 585 1.6 1.6 1.6 1.7 1.9 1.8 2 2 2 60° 60° 60° 521-9324 521-9326 521-9325 4-60 4-60 4-60 INTEGRAL RESISTOR, 5 VOLTS Part Number Color Peak Wavelength nm IV mcd Test Voltage Forward Current (mA) Viewing Angle 2Θ Θ½ LED Data sheet Page # 553-0311 Red 635 29 5 10 60° 521-9215 4-59 553-0322 553-0333 Green Yellow 565 585 19 12.6 5 5 10 10 60° 60° 521-9323 521-9322 4-59 4-59 Part Number Color Peak Wavelength nm IV mcd VF Volts Test Current (mA) Viewing Angle 2Θ Θ½ LED Data sheet Page # 553-0711 553-0744 Red/Green Yellow/Green 635/565 585/565 4.7/10 4.3/6.3 2/2.1 2.1*/2.1* 10 10 50° 80° 521-9459 521-9478 4-63 4-62 4 BI-COLOR * IF = 20mA NON-DIFFUSED Part Number Color Peak Wavelength nm IV mcd VF Volts* Test Current (mA) Viewing Angle 2Θ Θ½ LED Data sheet Page # 553-2211 Red 635 29 2 10 45° 521-9432 4-61 553-2222 553-2233 Green Yellow 565 585 50 20 2.1 2.1 10 10 45° 45° 521-9430 521-9431 4-61 4-61 * IF = 20mA CBI ARRAYS .200 PITCH Dialight offers its Multiarray to reduce insertions and to assure indicator alignment. Multiarrays mount indicators on .200 centers. These assemblies are available in arrays of 2 to 6. See pages 4-41 and 4-42 for information. Call factory for information on .185 pitched arrays. Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com 4-29 NEW 3mm Discrete LED Tinted, Diffused 521-9831 PART NO. SURFACE NOT FLAT 4.8 [.189] 4.4 [.173] 0.7 [.028] 0.4 [.016] 4.8 [.189] 4.4 [.173] 521-9831 0.6 [.024] 0.4 [.016] 2.9 [.114] ø 2.7 [.106] COLOR Blue³ 3.4 [.134] 3.1 [.122] 2.54 [.100] CATHODE 3.7 [.145] 3.5 [.138] 6.1 [.240] 5.7 [.224] 1.8 [.071] 1.2 [.047] 0.6 [.024] 0.4 [.016] 29 [1.142] 27 [1.063] MOUNTING CLIP: 515-0006 located on page 4-65 Dimensions in mm [inches] ATTENTION ³ OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC SENSITIVE DEVICES 4 Blue -9831 ABSOLUTE MAXIMUM RATINGS (TA=25°C) Power Dissipation (mW) 100 Forward Current (mA) Derating (mA/°C) From 55°C 20 .44 Operating Temperature (°C) -40/+100 Storage Temperature (°C) -40/+100 Soldering Temperature 260°C, 5 seconds, 1.6 mm from case Solder Adherence per MIL-STD-202E, Method 208C Blue OPERATING CHARACTERISTICS (TA=25°C) Luminous Intensity (mcd) IF=10mA -9831 Min. Typical 6.3 12 Peak Wavelength (nm) λ Peak Typical 428 Viewing Angle (2Θ½) Typical 70° Forward Voltage (V) IF=10mA Typical Max. 3.5 4.2 Reverse Voltage (V) IR=10µA Min. 3 Θ is the off axis angle at which the luminous intensity is half the axial luminous intensity Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com 4-57 3mm Discrete LED High Efficiency Diffused 521-9210, 4.45 [.175] 25.4 [1.0] MIN PART NO. COLOR 521-9210 Green 521-9211 Yellow 521-9216 Red 521-9498 Orange 521-9636 Red 3.30 [.13] 1.02 [.040] MIN 1.02 [.040] -9211, -9216, -9498, -9636 NEW 2.54 [.100] 3.00 [.118] 1.50 [.059] MAX 6.00 [.236] MOUNTING CLIP: 515-0006 located on page 4-65 .40 [.016] .45 [.016 ] short lead cathode all colors except 521-9636 Red. For 521-9636 Red, short lead is anode. Dimensions in mm [inches] Green Yellow Red Orange Red -9210 -9211 -9216 -9498 -9636 100 60 100 135 100 30 .4 20 .25 30 .4 25 .5 40 .51 Operating Temperature (°C) -55/+100 -55/+100 -55/+100 -55/+100 -55/+100 Storage Temperature (°C) -55/+100 -55/+100 -55/+100 -55/+100 -55/+100 ABSOLUTE MAXIMUM RATINGS (TA=25°C) Power Dissipation (mW) Forward Current (mA) Derating (mA/°C) From 50°C 1 from 25°C Soldering Temperature 260°C, 5 seconds, 1.6 mm from body Solder Adherence per MIL-STD-202E, Method 208C Green Yellow Red Orange Red OPERATING CHARACTERISTICS (TA=25°C) -9210 -9211 -9216 -9498 -9636 Luminous Intensity (mcd) IF=10mA 1 IF=20mA Min. Typical 4.7 12.6 7.4 10 7.4 10 3.4 7 8.71 481 Peak Wavelength (nm) λ Peak Typical 565 585 635 600 660 Viewing Angle (2Θ ½) Typical 60° 60° 60° 60° 60° Forward Voltage (V) IF=10mA 1 IF=20mA Typical Max. 2.11 2.81 2.11 2.81 21 2.81 2.2 3 1.81 2.41 Reverse Voltage (V), IR=100µA Max. 5 5 5 5 4 Θ is the off axis angle at which the luminous intensity is half the axial luminous intensity 4-58 Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com 3mm Discrete LED Integral Resistor, 5V Diffused 4.40 [.175] 1.01 [.040] 1.0 [.040] 521-9215, -9322, -9323 .457 [.018] SQ. 3.20 2.90 [.125] [.115] 2.54 [.100] 5.97 [.235] 2.41 [.950] MAX 1.27 [.050] PART NO. COLOR 521-9215 521-9322 521-9323 Red Yellow Green CATHODE MOUNTING CLIP: 515-0006 located on page 4-65 Dimensions in mm [inches] Red Yellow Green ABSOLUTE MAXIMUM RATINGS (TA=25°C) -9215 -9322 -9323 Forward Voltage (V) Derating (V/°C) From 50°C 7.5 .086 7.5 .086 7.5 .071 Operating Temperature (°C) -40/+85 -40/+85 -20/+85 Storage Temperature (°C) -55/+100 -55/+100 -55/+100 Soldering Temperature 260°C, 5 seconds, 1.6 mm from case Solder Adherence per MIL-STD-202E, Method 208C OPERATING CHARACTERISTICS (TA=25°C) Red Yellow Green -9215 -9322 -9323 Luminous Intensity (mcd) VF=5V Min. Typical 8.7 29 3.7 12.6 5.6 19 Peak Wavelength (nm) λ Peak Typical 635 585 565 Viewing Angle (2Θ½) Typical 60° 60° 60° Forward Current (mA) VF=5V Typical Max. 10 20 10 20 10 20 Reverse Voltage (V), IR=100µA Min. 5 5 5 Θ is the off axis angle at which the luminous intensity is half the axial luminous intensity Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com 4-59 4 3mm Discrete LED Low Current Diffused 521-9324, -9325, -9326 4.4 [.175] 1.01 [.040] .40 [.016] 1.0 [.040] 2.54 [.100] 3.3 [.130] 5.97 [.235] 1.00 26.67 [.040] [1.05] MIN. PART NO. COLOR 521-9324 521-9325 521-9326 Red Yellow Green .40 [.016] CATHODE Dimensions in mm [inches] MOUNTING CLIP: 515-0006 located on page 4-65 Red Yellow Green -9324 -9325 -9326 Power Dissipation (mW) 20 20 20 Forward Current (mA) Derating (mA/°C) From 90°C 7 .7 7 .7 7 .7 500 500 500 Operating Temperature (°C) -55/+100 -55/+100 -55/+100 Storage Temperature (°C) -55/+100 -55/+100 -55/+100 ABSOLUTE MAXIMUM RATINGS (TA=25°C) Peak Current (mA) Pulse width = 10 µs Soldering Temperature 260°C, 5 seconds, 1.6 mm from case Solder Adherence per MIL-STD-202E, Method 208C OPERATING CHARACTERISTICS (TA=25°C) Red Yellow Green -9324 -9325 -9326 Luminous Intensity (mcd) IF=2mA Min. Typical 1 1.6 1 1.6 1 1.6 Peak Wavelength (nm) λ Peak Typical 635 585 565 Viewing Angle (2Θ ½) Typical 60° 60° 60° Forward Voltage (V) IF=2mA Typical Max. 1.7 2.2 1.8 2.7 1.9 2.2 Reverse Voltage (V), IR=50µA Min. 5 5 5 Θ is the off axis angle at which the luminous intensity is half the axial luminous intensity 4-60 Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com 3mm Discrete LED High Efficiency Tinted, Non-Diffused 521-9430, -9431, -9432 3.2 [.126] 4.44 [.175] 1.0 [.040] .457 [.018] 1.0 [.040] PART NO. COLOR 521-9430 521-9431 521-9432 Green Yellow Red 2.54 [.100] 3.0 [.118] 5.97 MAX [.235] 25.4 [.100] MIN 1.27 [.050] .40 [.016] CATHODE Dimensions in mm [inches] MOUNTING CLIP: 515-0006 located on page 4-65 Green Yellow Red -9430 -9431 -9432 Power Dissipation (mW) 100 60 100 Forward Current (mA) Derating (mA/°C) From 50°C 30 .4 20 .25 30 .4 Peak Current (mA) 120 80 120 Operating Temperature (°C) -55/+100 -55/+100 -55/+100 Storage Temperature (°C) -55/+100 -55/+100 -55/+100 ABSOLUTE MAXIMUM RATINGS (TA=25°C) Pulse width = 100µs Soldering Temperature 260°C, 5 seconds, 1.6 mm from case Solder Adherence per MIL-STD-202E, Method 208C OPERATING CHARACTERISTICS (TA=25°C) Green Yellow Red -9430 -9431 -9432 Luminous Intensity (mcd) IF=10mA Min. Typical 32 50 10 20 8.7 29 Peak Wavelength (nm) λ Peak Typical 565 585 635 Viewing Angle (2Θ½) Typical 45° 45° 45° Forward Voltage (V) IF=20mA Typical Max. 2.1 2.8 2.1 2.8 2 2.8 Θ is the off axis angle at which the luminous intensity is half the axial luminous intensity Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com 4-61 4 3mm Discrete LED Bi-Color Non-Tinted, Diffused 521-9478, -9628, -9768 25.40 [1.00] MIN 1.02 [.040] 3.20 [.126] MAX RED CATHODE 521-9768 YELLOW CATHODE 521-9478 GREEN CATHODE 521-9628 3.00 [.118] 2.54 [.100] 4.45 [.175] 5.20 ±.5 [.205 ±.02] .50 [.020] TYP PART NO. COLOR 521-9478 Yellow/Green 521-9628 Red/Green 521-9768 Red/Yellow 2.54 [.100] NOM NOTE: MENISCUS MAY EXTEND 1.0MM [.040] DOWN FROM HOUSING Dimensions in mm [inches] MOUNTING CLIP: 515-0006 located on page 4-65 Yellow/Green Red/Green Red/Yellow ABSOLUTE MAXIMUM RATINGS (TA=25°C) -9478 -9628 -9768 Power Dissipation (mW) 60/100 140/100 100/60 Forward Current (mA) Derating (mA/°C) From 25°C 1 From 50°C 20/30 .251/.401 40/30 .5/.4 30/20 .41/.251 Peak Current (mA) 80/120 200/120 120/80 Operating Temperature (°C) -55/+100 -55/+100 -55/+100 Storage Temperature (°C) -55/+100 -55/+100 -55/+100 Pulse width = 10µs Soldering Temperature 260°C, 5 seconds, 1.66 mm from case Solder Adherence per MIL-STD-202E, Method 208C OPERATING CHARACTERISTICS (TA=25°C) Luminous Intensity (mcd) Min. IF=10mA * IF=20mA Typical Yellow/Green Red/Green Red/Yellow -9478 -9628 -9768 2.5/2.5 4.3/6.3 3.7*/1.1* 12.6*/3.7* 1.7*/1.7* 5.6*/5.6* Peak Wavelength (nm) λ Peak Typical 585/565 660/565 630/585 Viewing Angle (2Θ ½) Typical 80° 200° 80° Forward Voltage (V) IF=20mA Typical Max. 2.1/2.1 2.8/2.8 1.8/2.1 2.4/2.8 2/2.1 2.8/2.8 5 5 5 Reverse Voltage (V) IR=100ua Min. Θ is the off axis angle at which the luminous intensity is half the axial luminous intensity 4-62 Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com 3mm Discrete LED Bi-Color Non-Tinted, Diffused 4.59 [.181] 4.0 [.158] 1.0 [.040] 521-9459 CATHODE GREEN 3.40 [.134] MAX .50 [.020] SQ. NOM. 3.00 [.118] PART NO. COLOR 521-9459 Red/Green 2.54 [.100] 1.80 [.071] MAX 6.10 [.240] MOUNTING CLIP: 515-0006 located on page 4-65 26.92 [1.06] MIN Dimensions in mm [inches] 4 Red/Green -9459 ABSOLUTE MAXIMUM RATINGS (TA=25°C) Power Dissipation (mW) 140 Forward Current (mA) Derating (mA/°C) From 25°C 45 .6 Peak Current (mA) 1000 Pulse width = 10µs Operating Temperature (°C) -55/+100 Storage Temperature (°C) -55/+100 Soldering Temperature 260°C, 5 seconds, 1.6 mm from case Solder Adherence per MIL-STD-202E, Method 208C Red/Green OPERATING CHARACTERISTICS (TA=25°C) Luminous Intensity (mcd) IF=10mA -9459 Min. Typical 2.5/3.7 4.7/10 Peak Wavelength (nm) λ Peak Typical 635/565 Viewing Angle (2Θ½) Typical 50° Forward Voltage (V) IF=10mA Typical Max. 2/2.1 2.8/2.8 Θ is the off axis angle at which the luminous intensity is half the axial luminous intensity Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com 4-63 3mm Discrete LED High Efficiency Diffused 4.70 ±.20 [.185 ±.008] .79 ±.20 [.031 ±.008] 521-94xx TYPE 521-9408 521-9427 521-9428 3.30 [.130] MAX .50 [.020] NOM COLOR Green Red Yellow 2.49 ±.25 [.098 ±.010] 3.09 ±.20 [.122 ±.008] 1.30 ±.25 [.051 ±.010] 1.0 [.040] 24.00 ±.25 [.945 ±.010] 6.10 ±.38 [.240 ±.015] .50 [.020] NOM CATHODE (–) MOUNTING CLIP: 515-0006 located on page 4-65 Dimensions in mm [inches] Green Red Yellow -9408 -9427 -9428 Power Dissipation (mW) 75 60 60 Forward Current (mA) 25 20 20 ABSOLUTE MAXIMUM RATINGS (TA=25°C) Derating (mA/°C) .5 .5 .5 60 60 60 Operating Temperature (°C) -25/+85 -25/+85 -25/+85 Storage Temperature (°C) -30/+100 -30/+100 -30/+100 From 50°C Peak Current (mA) Soldering Temperature 260°C, 5 seconds, 1.6 mm from case Solder Adherence per MIL-STD-202E, Method 208C OPERATING CHARACTERISTICS (TA=25°C) Green Red Yellow -9408 -9427 -9428 Luminous Intensity (mcd) IF=10mA Min. Typical 5.6 16 3.6 10 2.2 6.3 Peak Wavelength (nm) λ Peak Typical 563 650 585 Viewing Angle (2Θ ½) Typical 45° 45° 45° Forward Voltage (V) IF=10mA Typical Max. 2.1 3 2 3 2.1 3 Reverse Voltage (V), IR=10µA Min. 3 3 3 Θ is the off axis angle at which the luminous intensity is half the axial luminous intensity 4-64 Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com