SAW Components Data Sheet B3780 SAW Components B3780 Low-loss Filter 433,92 MHz Data Sheet Ceramic package QCC8B Features ■ RF low-loss filter for remote control receivers ■ Package for Surface Mounted Technology (SMT) ■ Balanced and unbalanced operation possible ■ Passivation layer: Elpas ■ AEC-Q200 qualified component family Terminals ■ Ni, gold plated typ. dimensions in mm, approx. weight 0,07 g Pin configuration 1) 1 2 5 6 4,8 3,7 Input Ground (recommended) or Input Input (recommended) or Input Ground Output (recommended) or Output Ground Output Ground (recommended) or Output Case - Ground to be grounded Type Ordering code B3780 B39431-B3780-Z810 Marking and package according to C61157-A7-A46 Packing according to F61074-V8167-Z000 Electrostactic Sensitive Device (ESD) Maximum ratings Operable temperature range TA Storage temperature range Tstg VDC DC voltage Source power PS 1) The –45/+120 –45/+120 6 10 ˚C ˚C V dBm source impedance 50 Ω recommended pin configuration usually offers best suppression of electrical crosstalk.The filter characteristics refer to this configuration. 2 Dec 22, 2004 SAW Components B3780 Low-loss Filter 433,92 MHz Data Sheet Characteristics TA = –40 ... +85˚C ZS = 50 Ω and matching network ZL = 50 Ω and matching network Reference temperature: Terminating source impedance: Terminating load impedance: min. typ. max. — 433,92 — MHz — — 2,0 1,6 2,8 2,4 dB dB — 0,9 3,0 dB 780 850 920 kHz MHz MHz MHz MHz 48 42 28 18 53 47 33 21 — — — — dB dB dB dB MHz MHz MHz MHz MHz MHz 14 36 55 45 60 43 18 41 60 50 65 48 — — — — — — dB dB dB dB dB dB — 330 || 1,9 330 || 1,9 — Ω || pF — Ω || pF Center frequency (center frequency between 3 dB points) fC Minimum insertion attenuation including loss in matching elements excluding loss in matching elements αmin Pass band (relative to αmin) 433,645 ... 434,195 MHz Filter bandwidth αrel≤ 3 dB Relative attenuation (relative to αmin) 10,00 ... 414,00 414,00 ... 425,00 425,00 ... 431,50 431,50 ... 433,00 434,92 443,00 530,00 670,00 830,00 1000,00 ... 443,00 ... 530,00 ... 670,00 ... 830,00 ...1000,00 ...2500,00 αrel Impedance for pass band matching 1) Input: ZIN = RIN || CIN Output: ZOUT = ROUT || COUT — 1) Power matching of the SAW filter requires a certain source and load impedance. This characteristic impedance is provided by the 50 Ohm environment and a wideband matching network at input and output. After removing the SAW filter, the conjugate complex impedance values of the input and output matching network including the 50 Ohm environment are calculated. For more details, we refer to EPCOS application note #4. 3 Dec 22, 2004 SAW Components B3780 Low-loss Filter 433,92 MHz Data Sheet Matching network to 50 Ω (element values depend on pcb layout and equivalent circuit) Cp1 = 1,5 pF Ls2 = 39 nH Ls3 = 39 nH Cp4 = 1,5 pF Minimising the crosstalk For a good ultimate rejection a low crosstalk is necessary. Low crosstalk can be realised with a good RF layout. The major crosstalk mechanism is caused by the “ground-loop” problem. Grounding loops are created if input-and output transducer GND are connected on the top-side of the PCB and fed to the system grounding plane by a common via hole. To avoid the common ground path, the ground pin of the input- and output transducer are fed to the system ground plane (bottom PCB plane) by their own via hole. The transducers’ grounding pins should be isolated from the upper grounding plane. A common GND inductivity of 0.5nH degrades the ultimate rejection (crosstalk) by 20dB. The optimised PCB layout, including matching network for transformation to 50 Ohm, is shown here. In this PCB layout the grounding loops are minimised to realise good ultimate rejection. Optimised PCB layout for SAW filters in QCC8B package, pinning 1,5 (top side, scale 1:1) The bottom side is a copper plane (system ground area). The input and output grounding pins are isolated and connected to the common ground by separated via holes. For good contact of the upper grounding area with the lower side it is necessary to place enough via holes. 4 Dec 22, 2004 SAW Components B3780 Low-loss Filter 433,92 MHz Data Sheet Frequency response Frequency response (wideband) 5 Dec 22, 2004 SAW Components B3780 Low-loss Filter 433,92 MHz Data Sheet Frequency response (ultimate rejection) Published by EPCOS AG Surface Acoustic Wave Components Division, SAW CE AE PD P.O. Box 80 17 09, D-81617 München EPCOS AG 2004. All Rights Reserved. Reproduction, publication and dissemination of this brochure and the information contained therein without EPCOS’ prior express consent is prohibited. The information contained in this brochure describes the type of component and shall not be considered as guaranteed characteristics. Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and Electronics Industry recommended by the ZVEI (German Electrical and Electronic Manufacturers’ Association), unless otherwise agreed. This brochure replaces the previous edition. For questions on technology, prices and delivery please contact the Sales Offices of EPCOS AG or the international Representatives. Due to technical requirements components may contain dangerous substances. For information on the type in question please also contact one of our Sales Offices. 6 Dec 22, 2004