ESMT F49L800BA-90T

ESMT
F49L800UA/F49L800BA
8 Mbit (1M x 8/512K x 16)
3V Only CMOS Flash Memory
1. FEATURES
z
z
Single supply voltage 2.7V-3.6V
Fast access time: 70/90 ns
z
1,048,576x8 / 524,288x16 switchable by BYTE pin
Compatible with JEDEC standard
- Pin-out, packages and software commands
compatible with single-power supply Flash
z Low power consumption
- 7mA typical active current
- 25uA typical standby current 
z 100,000 program/erase cycles typically
z 20 years data retention
z Command register architecture
- Byte programming (9us typical)
- Sector Erase(sector structure: one 16 KB, two 8 KB,
one 32 KB, and fifteen 64 KB) 
z Auto Erase (chip & sector) and Auto Program
- Any combination of sectors can be erased
concurrently; Chip erase also provided.
- Automatically program and verify data at specified
address
z Erase Suspend/Erase Resume
- Suspend or Resume erasing sectors to allow the
read/program in another sector
z
z
z
z
z
z
z
z
Ready/Busy (RY/ BY )
- RY/ BY output pin for detection of program or erase
operation completion
End of program or erase detection
- Data polling
- Toggle bits
Hardware reset
- Hardware pin( RESET ) resets the internal state machine
to the read mode
Sector Protection /Unprotection
- Hardware Protect/Unprotect any combination of sectors
from a program or erase operation.
Low VCC Write inhibit is equal to or less than 2.0V
Boot Sector Architecture
- U = Upper Boot Block
- B = Bottom Boot Block
Packages available:
- 48-pin TSOPI
2. ORDERING INFORMATION
Part No
Boot
Speed
Package
Part No
Boot
Speed
Package
F49L800UA-70T
Upper
70 ns
TSOPI
F49L800UA-90T
Upper
90 ns
TSOPI
F49L800BA-70T
Bottom
70 ns
TSOPI
F49L800BA-90T
Bottom
90 ns
TSOPI
3. GENERAL DESCRIPTION
The F49L800UA/F49L800BA is a 8 Megabit, 3V only
CMOS Flash memory device organized as 1M bytes of 8
bits or 512K words of 16bits. This device is packaged in
standard 48-pin TSOP. It is designed to be programmed
and erased both in system and can in standard EPROM
programmers.
With access times of 70 ns and 90 ns, the
F49L800UA/F49L800BA allows the operation of
high-speed microprocessors. The device has separate
chip enable CE , write enable WE , and output enable OE
controls. ESMT's memory devices reliably store memory
data even after 100,000 program and erase cycles.
The F49L800UA/F49L800BA is entirely pin and
command set compatible with the JEDEC standard for 8
Megabit Flash memory devices. Commands are written to
the command register using standard microprocessor
write timings.
Elite Semiconductor Memory Technology Inc.
The F49L800UA/F49L800BA features a sector erase
architecture. The device memory array is divided into one
16 Kbytes, two 8 Kbytes, one 32 Kbytes, and fifteen 64
Kbytes. Sectors can be erased individually or in groups
without affecting the data in other sectors. Multiple-sector
erase and whole chip erase capabilities provide the
flexibility to revise the data in the device.
The sector protect/unprotect feature disables both
program and erase operations in any combination of the
sectors of the memory. This can be achieved in-system or
via programming equipment.
A low VCC detector inhibits write operations on loss of
power. End of program or erase is detected by the
Ready/Busy status pin, Data Polling of DQ7, or by the
Toggle Bit I feature on DQ6. Once the program or erase
cycle has been successfully completed, the device
internally resets to the Read mode.
Publication Date : May. 2007
Revision: 1.2
1/47
ESMT
F49L800UA/F49L800BA
4. PIN CONFIGURATIONS
4.1
48-pin TSOP
4.2
A15
1
48
A16
A14
2
47
BYTE
A13
3
46
GND
A12
4
45
DQ15/A-1
A11
5
44
DQ7
A10
6
43
DQ14
A9
7
42
DQ6
A8
8
41
DQ13
NC
9
40
DQ5
NC
10
39
DQ12
WE
11
38
DQ4
RESET
12
37
VCC
NC
13
36
DQ11
NC
14
35
DQ3
RY/BY
15
34
DQ10
A18
16
33
DQ2
A17
17
32
DQ9
A7
18
31
DQ1
A6
19
30
DQ8
A5
20
29
DQ0
A4
21
28
OE
A3
22
27
GND
A2
23
26
CE
A1
24
25
A0
F49L800U/BA
Pin Description
Symbol
Pin Name
Functions
A0~A18
Address Input
DQ0~DQ14
Data Input/Output
DQ15/A-1
Q15 (Word mode) /
LSB addr (Byte Mode)
To bi-direction date I/O when BYTE is High
CE
Chip Enable
To activate the device when CE is low.
OE
Output Enable
To gate the data output buffers.
WE
Write Enable
To control the Write operations.
RESET
Reset
Hardware Reset Pin/Sector Protect Unprotect
BYTE
Word/Byte selection input
To select word mode or byte mode
RY/ BY
VCC
GND
NC
Ready/Busy
To check device operation status
Power Supply
Ground
No connection
To provide power
Elite Semiconductor Memory Technology Inc.
To provide memory addresses.
To output data when Read and receive data when Write.
The outputs are in tri-state when OE or CE is high.
To input address when BYTE is Low
Publication Date : May. 2007
Revision: 1.2
2/47
ESMT
F49L800UA/F49L800BA
5. SECTOR STRUCTURE
Table 1: F49L800UA Sector Address Table
Sector
Sector Size
Byte Mode
Address range
Word Mode
Byte Mode(x8)
Sector Address
Word Mode(x16) A18 A17 A16 A15 A14 A13 A12
SA0
64Kbytes
32Kwords
00000H-0FFFFH
00000H-07FFFH
0
0
0
0
X
X
X
SA1
64Kbytes
32Kwords
10000H-1FFFFH
08000H-0FFFFH
0
0
0
1
X
X
X
SA2
64Kbytes
32Kwords
20000H-2FFFFH
10000H-17FFFH
0
0
1
0
X
X
X
SA3
64Kbytes
32Kwords
30000H-3FFFFH
18000H-1FFFFH
0
0
1
1
X
X
X
SA4
64Kbytes
32Kwords
40000H-4FFFFH
20000H-27FFFH
0
1
0
0
X
X
X
SA5
64Kbytes
32Kwords
50000H-5FFFFH
28000H-2FFFFH
0
1
0
1
X
X
X
SA6
64Kbytes
32Kwords
60000H-6FFFFH
30000H-37FFFH
0
1
1
0
X
X
X
SA7
64Kbytes
32Kwords
70000H-7FFFFH
38000H-3FFFFH
0
1
1
1
X
X
X
SA8
64Kbytes
32Kwords
80000H-8FFFFH
40000H-47FFFH
1
0
0
0
X
X
X
SA9
64Kbytes
32Kwords
90000H-9FFFFH
48000H-4FFFFH
1
0
0
1
X
X
X
SA10
64Kbytes
32Kwords
A0000H-AFFFFH
50000H-57FFFH
1
0
1
0
X
X
X
SA11
64Kbytes
32Kwords
B0000H-BFFFFH
58000H-5FFFFH
1
0
1
1
X
X
X
SA12
64Kbytes
32Kwords
C0000H-CFFFFH
60000H-67FFFH
1
1
0
0
X
X
X
SA13
64Kbytes
32Kwords
D0000H-DFFFFH
68000H-6FFFFH
1
1
0
1
X
X
X
SA14
64Kbytes
32Kwords
E0000H-EFFFFH
70000H-77FFFH
1
1
1
0
X
X
X
SA15
32Kbytes
16Kwords
F0000H-F7FFFH
78000H-7BFFFH
1
1
1
1
0
X
X
SA16
8Kbytes
4Kwords
F8000H-F9FFFH
7C000H-7CFFFH
1
1
1
1
1
0
0
SA17
8Kbytes
4Kwords
FA000H-FBFFFH
7D000H-7DFFFH
1
1
1
1
1
0
1
SA18
16Kbytes
8Kwords
FC000H-FFFFFH 7E000H-7FFFFH
1
Note: Byte Mode: address range A18:A-1, Word mode : address range A18:A0
1
1
1
1
1
X
Table 2: F49L800BA Sector Address Table
Sector
Sector Size
Address range
Sector Address
Byte Mode
Word Mode
Byte Mode(x8)
Word Mode(x16) A18 A17 A16 A15 A14 A13 A12
SA0
16Kbytes
8Kwords
00000H-03FFFH
00000H-01FFFH
0
0
0
0
0
0
X
SA1
8Kbytes
4Kwords
04000H-05FFFH
02000H-02FFFH
0
0
0
0
0
1
0
SA2
8Kbytes
4Kwords
06000H-07FFFH
03000H-03FFFH
0
0
0
0
0
1
1
SA3
32Kbytes
16Kwords
08000H-0FFFFH
04000H-07FFFH
0
0
0
0
1
X
X
SA4
64Kbytes
32Kwords
10000H-1FFFFH
08000H-0FFFFH
0
0
0
1
X
X
X
SA5
64Kbytes
32Kwords
20000H-2FFFFH
10000H-17FFFH
0
0
1
0
X
X
X
SA6
64Kbytes
32Kwords
30000H-3FFFFH
18000H-1FFFFH
0
0
1
1
X
X
X
SA7
64Kbytes
32Kwords
40000H-4FFFFH
20000H-27FFFH
0
1
0
0
X
X
X
SA8
64Kbytes
32Kwords
50000H-5FFFFH
28000H-2FFFFH
0
1
0
1
X
X
X
SA9
64Kbytes
32Kwords
60000H-6FFFFH
30000H-37FFFH
0
1
1
0
X
X
X
SA10
64Kbytes
32Kwords
70000H-7FFFFH
38000H-3FFFFH
0
1
1
1
X
X
X
SA11
64Kbytes
32Kwords
80000H-8FFFFH
40000H-47FFFH
1
0
0
0
X
X
X
SA12
64Kbytes
32Kwords
90000H-9FFFFH
48000H-4FFFFH
1
0
0
1
X
X
X
SA13
64Kbytes
32Kwords
A0000H-AFFFFH
50000H-57FFFH
1
0
1
0
X
X
X
SA14
64Kbytes
32Kwords
B0000H-BFFFFH
58000H-5FFFFH
1
0
1
1
X
X
X
SA15
64Kbytes
32Kwords
C0000H-CFFFFH
60000H-67FFFH
1
1
0
0
X
X
X
SA16
64Kbytes
32Kwords
D0000H-DFFFFH
68000H-6FFFFH
1
1
0
1
X
X
X
SA17
64Kbytes
32Kwords
E0000H-EFFFFH
70000H-77FFFH
1
1
1
0
X
X
X
SA18
64Kbytes
32Kwords
F0000H-FFFFFH
78000H-7FFFFH
1
1
1
1
X
X
X
Note: Byte Mode: address range A18:A-1, Word mode : address range A18:A0
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
3/47
ESMT
F49L800UA/F49L800BA
6. FUNCTIONAL BLOCK DIAGRAM
BYTE
CE
OE
WE
RES ET
ADDRESS
LATCH
AND
BUFFER
PROGRAM / ERASE
HIGH VOLTAGE
X-DECODER
A0~A18
CONTROL
INPUT
LOGIC
WRITE
STATE
MACHING
(WSM)
STATE
REGISTER
F49L800U/BA
FLASH
ARRAY
Y-DECODER
Y-PASS GATE
SENSE
AMPLIFIER
PGM
DATA
HV
ARRAY
SOURCE
HV
COMMAND
DATA
DECODER
COMMAND
DATA LATCH
PROGRAM
DATA LATCH
DQ0~DQ15(A-1)
Elite Semiconductor Memory Technology Inc.
I / O BUFFER
Publication Date : May. 2007
Revision: 1.2
4/47
ESMT
F49L800UA/F49L800BA
7. FUNCTIONAL DESCRIPTION
7.1 Device operation
This section describes the requirements and use
of the device bus operations, which are initiated
through the internal command register. The
register is composed of latches that store the
command, address and data information needed
to execute the command. The contents of the
register serve as inputs to the internal state
machine. The state machine outputs dictate the
function of the device. The F49L800UA
/F49L800BA features various bus operations as
Table 3.
Table 3. F49L800UA/F49L800BA Operation Modes Selection
ADDRESS
DESCRIPTION
CE
OE WE
DQ8~DQ15
RESET A18 A11
A8
A5
DQ0~DQ7
BYTE
|
|
|
|
A9
A6
A1 A0
=VIH
A12 A10
A7
A2
BYTE
=VIL
Reset(3)
X
X
X
L, Vss±
0.3V(3)
X
High Z
High Z
High Z
Read
L
L
H
H
AIN
Dout
Dout
DQ8~DQ14=
Write
L
H
L
H
AIN
DIN
DIN
High Z
DQ15=A-1
Output Disable
L
H
H
H
X
High Z
High Z
High Z
VCC±
0.3V
X
X
VCC±
0.3V
X
High Z
High Z
High Z
Sector Protect(2)
L
H
L
VID
SA
X
X
X
L
X
H
L
DIN
X
X
Sector Unprotect(2)
L
H
L
VID
SA
X
X
X
H
X
H
L
DIN
X
X
Temporary sector unprotect
X
X
X
VID
DIN
DIN
High Z
Standby
Auto-select
AIN
See Table 4
Notes:
1. L= Logic Low = VIL, H= Logic High = VIH, X= Don't Care, SA= Sector Address, VID=11.5V to 12.5V.
AIN= Address In, DIN = Data In, Dout = Data Out.
2. The sector protect and unprotect functions may also be implemented via programming equipment.
3. See “Reset Mode” section.
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
5/47
ESMT
F49L800UA/F49L800BA
Table 4. F49L800UA/F49L800BA Auto-Select Mode (High Voltage Method)
Description
Mode
CE OE
WE
A18 A11
to
to
A12 A10 A9
Manufacturer ID: ESMT
L
L
H
Device ID:
F49L800UA
(Upper Boot Block)
Word
L
L
H
Byte
L
L
H
Word
L
L
H
Byte
L
L
H
Sector Protection Verification
L
L
H
Device ID:
F49L800BA
(Bottom Boot Block)
A8
A5
DQ8
DQ7
to
to
to
to
A7 A6
A2
A1
A0
DQ15
DQ0
X
7FH
22H
DAH
X
DAH
22H
5BH
X
5BH
01H
(protected)
00H
(unprotected)
X
X
VID
X
L
X
L
L
X
X
VID
X
L
X
L
H
X
SA
X
X
VID
VID
X
X
L
L
X
X
L
H
H
L
X
X
L= Logic Low=VIL, H= Logic High=VIH, SA= Sector Address, X= Don’t care.
Notes :
1.Manufacturer and device codes may also be accessed via the software command sequence in Table 5.
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
6/47
ESMT
Reset Mode :
Hardware Reset
When the RESET pin is driven low for at least a
period of tRP, the device immediately terminates any
operation in progress, tri-states all output pins, and
ignores all read/write commands for the duration of the
RESET pulse. The device also resets the internal state
machine to reading array data. The operation that was
interrupted should be reinitiated later once the device is
ready to accept another command sequence, to ensure
the data integrity.
The current is reduced for the duration of the RESET
pulse. When RESET is held at VSS±0.3V, the device
draws CMOS standby current (ICC4). If RESET is held
at VIL but not within VSS±0.3V, the standby current will
be greater.
The RESET pin may be tied to system reset circuitry.
A system reset would thus reset the Flash memory,
enabling the system to read the boot-up firm-ware from
the Flash memory.
If RESET is asserted during a program or erase
embedded algorithm operation, the RY/ BY pin remains
a "0" (busy) until the internal reset operation is
complete, which requires a time of tREADY (during
Embedded Algorithms). The system can thus monitor
RY/ BY to determine whether the reset operation is
complete.
If RESET is asserted when a program or erase
operation is not executing , i.e. the RY/ BY is “1”, the
reset operation is completed within a time of tREADY (not
during Embedded Algorithms). The system can read
data after tRH when the RESET pin returns to VIH.
Refer to the AC Characteristics tables 13 for Hardware
Reset section & Figure 23 for the timing diagram.
Read Mode
To read array data from the outputs, the system must
drive the CE and OE pins to VIL. CE is the power
control and selects the device. OE is the output
control and gates array data to the output pins. WE
should remain at VIH. The internal state machine is set
for reading array data upon device power-up, or after a
hardware reset. This ensures that no spurious
alteration of the memory content occurs during the
power transition.
No command is necessary in this mode to obtain array
data. Standard microprocessor’s read cycles that assert
Elite Semiconductor Memory Technology Inc.
F49L800UA/F49L800BA
valid addresses on the device address inputs produce
valid data on the device data outputs. The device remains
enabled for read access until the command register
contents are altered.
See “Read Command” section for more information.
Refer to the AC Read Operations table 10 for timing
specifications and to Figure 5 for the timing diagram. ICC1
in the DC Characteristics table represents the active
current specification for reading array data.
Write Mode
To write a command or command sequence (which
includes programming data to the device and erasing
sectors of memory), the system must drive WE and CE
to VIL, and OE to VIH. The “Program Command” section
has details on programming data to the device using
standard command sequences.
An erase operation can erase one sector, multiple
sectors, or the entire device. Tables 1 and 2 indicate the
address space that each sector occupies. A “sector
address” consists of the address bits required to uniquely
select a sector. The “Software Command Definitions”
section has details on erasing a sector or the entire chip,
or suspending/resuming the erase operation.
When the system writes the auto-select command
sequence, the device enters the auto-select mode. The
system can then read auto-select codes from the internal
register (which is separate from the memory array) on
DQ7–DQ0. Standard read cycle timings apply in this
mode. Refer to the Auto-select Mode and Auto-select
Command sections for more information. ICC2 in the DC
Characteristics table represents the active current
specification for the write mode. The “AC Characteristics”
section contains timing specification tables and timing
diagrams for write operations.
Automatic Sleep Mode
The automatic sleep mode minimizes Flash device
energy consumption. The device automatically enables
this mode when addresses remain unchanged for over
250ns. The automatic sleep mode is independent of the
CE , WE , and OE control signals. Standard address
access timings provide new data when addresses are
changed. While in sleep mode, output data is latched and
always available to the system. ICC4 in the DC
Characteristics table represents the automatic sleep
mode current specification.
Word / Byte Mode
This pin control the I/O configuration of device. When
BYTE = VIH or Vcc ± 0.3V. The I/O configuration is x16
and the pin of D15/A-1 is bi-direction Data I/O. However,
BYTE = VIL or VSS ± 0.3V. The I/O configuration would
be x8 and The pin of DQ15/A-1 only address input pin.
You must define the function of this pin before enable this
device.
Publication Date : May. 2007
Revision: 1.2
7/47
ESMT
F49L800UA/F49L800BA
Temporary Sector Unprotect Mode
This feature allows temporary unprotection of previously
protected sector to change data in-system. This mode is
activated by setting the RESET pin to VID(11.5V-12.5V).
During this mode, all formerly protected sectors are
un-protected and can be programmed or erased by
selecting the sector addresses. Once VID is removed from
the RESET pin, all the previously protected sectors are
protected again.
Start
RESET = V ID (Note 1)
Perform Erase or
Program Operation
Operation Completed
RESET = V I H
Temporary Sector
Unprotect Completed
(Note 2)
Notes:
1. All protected sectors unprotected.
2. All previously protected sectors are protected once again.
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
8/47
ESMT
Output Disable Mode
With the OE is at a logic high level (VIH), outputs from
the devices are disabled. This will cause the output pins
in a high impedance state
Standby Mode
When CE and RESET are both held at VCC ± 0.3V,
the device enter CMOS Standby mode. If CE and
RESET are held at VIH, but not within the range of
VCC ± 0.3V, the device will still be in the standby mode,
but the standby current will be larger.
If the device is deselected during auto algorithm of
erasure or programming, the device draws active
current ICC2 until the operation is completed. ICC3 in
the DC Characteristics table represents the standby
current specification.
The device requires standard access time (tCE) for
read access from either of these standby modes,
before it is ready to read data.
Sector Protect / Un-protect Mode
The hardware sector protect feature disables both
program and erase operations in any sector. The
hardware sector unprotect feature re-enables both the
program and erase operations in previously protected
sectors. Sector protect/unprotect can be implemented
via two methods.
The primary method requires VID on the RESET pin
only, and can be implemented either in-system or via
programming equipment.
F49L800UA/F49L800BA
Figure 16 shows the algorithms and Figure 15 shows
the timing diagram. This method uses standard
microprocessor bus cycle timing. For sector unprotect,
all unprotected sectors must first be protected prior to
the first sector unprotect write cycle.
The alternate method intended only for programming
equipment requires VID on address pin A9, OE , and
RESET .
Auto-select Mode
The auto-select mode provides manufacturer and
device identification and sector protection verification,
through outputs on DQ7–DQ0. This mode is primarily
intended for programming equipment to automatically
match a device to be programmed with its
corresponding programming algorithm. However, the
auto-select codes can also be accessed in-system
through the command register.
When using programming equipment, this mode
requires VID (11.5 V to 12.5 V) on address pin A9.
While address pins A3, A2, A1, and A0 must be as
shown in Table 4.
To verify sector protection, all necessary pins have to
be set as required in Table 4, the programming
equipment may then read the corresponding identifier
code on DQ7-DQ0.
To access the auto-select codes in-system, the host
system can issue the auto-select command via the
command register, as shown in Table 5. This method
does not require VID. See “ Software Command
Definitions” for details on using the auto-select mode.
7.2 Software Command Definitions
Writing specific address and data commands or
sequences into the command register initiates the
device operations. Table 5 defines the valid register
command sequences. Writing incorrect address and
data values or writing them in the improper sequence
resets the device to reading array data.
Elite Semiconductor Memory Technology Inc.
All addresses are latched on the falling edge of WE
or CE , whichever happens later. All data is latched on
the rising edge of WE or CE , whichever happens
first. Refer to the corresponding timing diagrams in
the AC Characteristics section.
Publication Date : May. 2007
Revision: 1.2
9/47
ESMT
F49L800UA/F49L800BA
Table 5. F49L800UA/F49L800BA Software Command Definitions
Bus
Cycles
Command
1st Bus
Cycle
2nd Bus
Cycle
3rd Bus
Cycle
4th Bus
Cycle
5th Bus
Cycle
6th Bus
Cycle
Addr
Data
Addr
Data
Addr
Data
Addr
Data
Addr
Data
Addr
Data
Reset (5)
1
XXXH
F0H
-
-
-
-
-
-
-
-
-
-
Read (4)
1
RA
RD
-
-
-
-
-
-
-
-
-
-
Word
4
555H
AAH
2AAH
55H
555H
A0H
PA
PD
Byte
4
AAAH AAH
555H
55H
AAAH
A0H
PA
PD
Word
6
555H
AAH
2AAH
55H
555H
80H
555H
AAH
2AAH
55H
555H
10H
Byte
6
AAAH AAH
555H
55H
AAAH
80H
AAAH AAH
555H
55H
AAAH
10H
Word
6
555H
AAH
2AAH
55H
555H
80H
555H
AAH
2AAH
55H
SA
30H
Byte
6
AAAH AAH
555H
55H
AAAH
80H
AAAH AAH
555H
55H
SA
30H
Sector Erase
Suspend (6)
1
XXXH
B0H
-
-
-
-
-
-
-
-
-
-
Sector Erase Resume
(7)
1
XXXH
30H
-
-
-
-
-
-
-
-
-
-
Program
Chip Erase
Sector Erase
Auto-select
See Table 6.
Notes:
1. X = don’t care
RA = Address of memory location to be read.
RD = Data to be read at location RA.
PA = Address of memory location to be programmed.
PD = Data to be programmed at location PA.
SA = Address of the sector.
2. Except Read command and Auto-select command, all command bus cycles are write operations.
3. The system should generate the following address patterns: 555H or 2AAH to address A10~A0 in word mode
/ AAAH or 555H to address A10~A-1 in byte mode.
4. Address bits A18–A11 are don’t cares.
5. No command cycles required when reading array data.
6. The Reset command is required to return to reading array data when device is in the auto-select mode, or if
DQ5 goes high(while the device is providing status data).
7. The system may read and program in non-erasing sectors, or enter the auto-select mode, when in the Erase
Suspend mode. The Erase Suspend command is valid only during a sector erase operation.
8. The Erase Resume command is valid only during the Erase Suspend mode.
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
10/47
ESMT
F49L800UA/F49L800BA
Table 6. F49L800UA/F49L800BA Auto-Select Command
Bus
Cycles
Command
Manufacture ID
1st Bus
Cycle
2nd Bus
Cycle
3rd Bus
Cycle
4th Bus
Cycle
6th Bus
Cycle
Addr
Data Addr
Data
Addr
Data
Addr
Data
4
555H
AAH 2AAH
55H
555H
90H
X04H
7FH
-
-
-
-
4
555H
AAH 2AAH
55H
555H
90H
X08H
7FH
-
-
-
-
4
555H
AAH 2AAH
55H
555H
90H
X0CH
7FH
-
-
-
-
4
555H
AAH 2AAH
55H
555H
90H
X00H
8CH
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Device ID,
Upper boot
Word
4
555H
AAH 2AAH
55H
555H
90H
X01H 22DAH
Byte
4
AAAH AAH 555H
55H
AAAH
90H
X02H
Device ID,
Bottom boot
Word
4
555H
AAH 2AAH
55H
555H
90H
X01H 225BH
Byte
4
AAAH AAH 555H
55H
AAAH
90H
X02H
Word
4
555H
55H
555H
90H
(SA) XX00H
x02H XX00H
90H
(SA)
x04H
AAH 2AAH
Sector Protect Verify
Byte
5th Bus
Cycle
4
AAAH AAH 555H
55H
AAAH
Addr Data Addr Data
DAH
5BH
00H
01H
Notes :
1. The fourth cycle of the auto-select command sequence is a read cycle.
2.
For Sector Protect Verify operation: If read out data is 01H, it means the sector has been protected. If read
out data is 00H, it means the sector is still not being protected.
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
11/47
ESMT
F49L800UA/F49L800BA
Reset Command
Program Command
Writing the reset command to the device resets the
device to reading array data. Address bits are all don’t
cares for this command.
The program command sequence programs one byte
into the device. Programming is a four-bus-cycle
operation. The program command sequence is initiated
by writing two unlock write cycles, followed by the
program set-up command. The program address and
data are written next, which in turn initiate the
Embedded Program algorithm. The system is not
required to provide further controls or timings. The
device automatically provides internally generated
program pulses and verifies the programmed cell
margin.
The reset command may be written between the
sequence cycles in an erase command sequence
before erasing begins. This resets the device to reading
array data. Once erasure begins, however, the device
ignores reset commands until the operation is
complete.
The reset command may be written between the
sequence cycles in a program command sequence
before programming begins. This resets the device to
reading array data (also applies to programming in
Erase Suspend mode). Once programming begins,
however, the device ignores reset commands until the
operation is complete.
The reset command may be written between the
sequence cycles in an auto-select command sequence.
Once in the auto-select mode, the reset command must
be written to return to reading array data (also applies
to auto-select during Erase Suspend).
If DQ5 goes high(see “DQ5: Exceeded Timing Limits”
section) during a program or erase operation, writing
the reset command returns the device to reading array
data (also applies during Erase Suspend).
Read Command
The device is automatically set to reading array data
after device power-up. No commands are required to
retrieve data. The device is also ready to read array
data after completing an Embedded Program or
Embedded Erase algorithm.
When the device accepts an Erase Suspend command,
the device enters the Erase Suspend mode. The
system can read array data using the standard read
timings, except that if it reads an address within
erase-suspended sectors, the device outputs status
data. After completing a programming operation in the
Erase Suspend mode, the system may once again read
array data with the same exception. See “Erase
Suspend/Erase Resume Commands” for more
information on this mode.
The system must issue the reset command to
re-enable the device for reading array data if DQ5 goes
high, or while in the auto-select mode. See the “Reset
Command” section. See also the “Read Mode” in the
“Device Operations” section for more information. Refer
to Figure 5 for the timing diagram.
Elite Semiconductor Memory Technology Inc.
When the Embedded Program algorithm is complete,
the device then returns to reading array data and
addresses are no longer latched. The system can
determine the status of the program operation by using
DQ7, DQ6, or RY/ BY . See “Write Operation Status”
section for more information on these status bits.
Any commands written to the device during the
Embedded Program Algorithm are ignored. Note that a
hardware
reset
immediately
terminates
the
programming operation. The Program command
sequence should be reinitiated once the device has
reset to reading array data, to ensure data integrity.
Programming is allowed in any sequence and across
sector boundaries. A bit cannot be programmed from a
“0” back to a “1”. Attempting to do so may halt the
operation and set DQ5 to “1”, or cause the Data Polling
algorithm to indicate the operation was successful.
However, a succeeding read will show that the data is
still “0”. Only erase operations can convert a “0” to a
“1”.
Chip Erase Command
Chip erase is a six-bus cycle operation. The chip erase
command sequence is initiated by writing two unlock
cycles, followed by a set-up command. Two additional
unlock write cycles are then followed by the chip erase
command, which in turn invokes the Embedded Erase
algorithm.
The device does not require the system to preprogram
prior to erase. The Embedded Erase algorithm
automatically preprograms and verifies the entire
memory for an all zero data pattern prior to electrical
erase.
Any commands written to the chip during the
Embedded Erase algorithm are ignored. Note that a
hardware reset during the chip erase operation
immediately terminates the operation. The Chip Erase
command sequence should be reinitiated once the
device has returned to reading array data, to ensure
the data integrity.
Publication Date : May. 2007
Revision: 1.2
12/47
ESMT
The system can determine the status of the erase
operation by using DQ7, DQ6, DQ2, or RY/ BY . See
“Write Operation Status” section for more information
on these status bits.
When the Embedded Erase algorithm is complete, the
device returns to reading array data and addresses are
no longer latched. See the Erase/Program Operations
tables in “AC Characteristics” for parameters.
Sector Erase Command
Sector erase is a six-bus cycle operation. The sector
erase command sequence is initiated by writing two
unlock cycles, followed by a set-up command. Two
additional unlock write cycles are then followed by the
address of the sector to be erased, and the sector
erase command.
The device does not require the system to preprogram
the memory prior to erase. The Embedded Erase
algorithm
automatically programs and verifies the sector for an all
zero data pattern prior to electrical erase. The system is
not required to provide any controls or timings during
these operations.
After the command sequence is written, a sector erase
time-out of 50 µs begins. During the time-out period,
additional sector addresses and sector erase
commands may be written. Loading the sector erase
buffer may be done in any sequence, and the number
of sectors may be from one sector to all sectors. The
time between these additional cycles must be less than
50 μs, otherwise the last address and command might
not be accepted, and erasure may begin.
It is recommended that processor interrupts be disabled
during this time to ensure all commands are accepted.
The interrupts can be re-enabled after the last Sector
Erase command is written. If the time between
additional sector erase commands can be assumed to
be less than 50 µs, the system need not monitor DQ3.
Any command other than Sector Erase or Erase
Suspend during the time-out period resets the device to
reading array data. The system must rewrite the
command sequence and any additional sector
addresses and commands.
The system can monitor DQ3 to determine if the sector
erase timer has timed out. (See the “DQ3: Sector Erase
Timer” section.) The time-out begins from the rising
edge of the final WE pulse in the command
sequence.
Once the sector erase operation has begun, only the
Erase Suspend command is valid. All other commands
are ignored. Note that a hardware reset during the
sector erase operation immediately terminates the
Elite Semiconductor Memory Technology Inc.
F49L800UA/F49L800BA
operation. The Sector Erase command sequence
should be reinitiated once the device has returned to
reading array data, to ensure the data integrity.
When the Embedded Erase algorithm is complete, the
device returns to reading array data and addresses are
no longer latched. The system can determine the
status of the erase operation by using DQ7, DQ6,
DQ2, or RY/ BY . (Refer to “Write Operation Status”
section for more information on these status bits.)
Refer to the Erase/Program Operations tables in the
“AC Characteristics” section for parameters.
Sector Erase Suspend/Resume Command
The Erase Suspend command allows the system to
interrupt a sector erase operation and then read data
from, or program data to, any sector not selected for
erasure (The device “erase suspends” all sectors
selected for erasure.). This command is valid only
during the sector erase operation, including the 50 µs
time-out period during the sector erase command
sequence. The Erase Suspend command is ignored if
written during the chip erase operation or Embedded
Program algorithm. Addresses are “don’t-cares” when
writing the Erase Suspend command as shown in
Table 5.
When the Erase Suspend command is written during a
sector erase operation, the device requires a maximum
of 20 µs to suspend the erase operation. However,
when the Erase Suspend command is written during
the sector erase time-out, the device immediately
terminates the time-out period and suspends the erase
operation.
Reading at any address within erase-suspended
sectors produces status data on DQ7–DQ0. The
system can use DQ7, or DQ6 and DQ2 together, to
determine if a sector is actively erasing or is
erase-suspended. See “Write Operation Status”
section for more information on these status bits.
After an erase-suspended program operation is
complete, the system can once again read array data
within non-suspended sectors. The system can
determine the status of the program operation using
the DQ7 or DQ6 status bits, just as in the standard
program operation. See “Write Operation Status” for
more information.
The system may also write the auto-select command
sequence when the device is in the Erase Suspend
mode. The device allows reading auto-select codes
even at addresses within erasing sectors, since the
codes are not stored in the memory array. When the
device exits the auto-select mode, the device reverts to
the Erase Suspend mode, and is ready for another
valid operation.
Publication Date : May. 2007
Revision: 1.2
13/47
ESMT
F49L800UA/F49L800BA
The system must write the Erase Resume command
(address bits are “don’t care” as shown in Table 5) to
exit the erase suspend mode and continue the sector
erase operation. Further writes of the Resume
command are ignored. Another Erase Suspend
command can be written after the device has resumed
erasing.
Auto-select Command
The auto-select command sequence allows the host
system to access the manufacturer and devices codes,
and determine whether or not a sector is protected.
Table 6 shows the address and data requirements. This
method is an alternative to that shown in Table 4, which
is intended for PROM programmers and requires VID
on address bit A9.
The auto-select command sequence is initiated by
writing two unlock cycles, followed by the auto-select
command. The device then enters the auto-select
mode, and the system may read at any address any
number of times, without initiating another command
sequence. The read cycles at address 04H, 08H, 0CH,
and 00H retrieves the ESMT manufacturer ID. A read
cycle at address 01H retrieves the device ID. A read
cycle containing a sector address (SA) and the
address 02H returns 01H if that sector is protected, or
00H if it is unprotected. Refer to Tables 1 and 2 for
valid sector addresses.
The system must write the reset command to exit the
auto-select mode and return to reading array data.
7.3 Write Operation Status
The device provides several bits to determine the
status of a write operation: RY/ BY , DQ7, DQ6,
DQ5, DQ3, DQ2, and. Table 7 and the following
subsections describe the functions of these bits.
RY/ BY , DQ7, and DQ6 each offer a method for
determining whether a program or erase operation
is complete or in progress.
Table 7. Write Operation Status
Status
Embedded Program Algorithm
Embedded Erase Algorithm
In Progress
Reading Erase Suspended
Sector
Erase Suspended Mode Reading Non-Erase
Suspended Sector
Erase Suspend Program
Embedded Program Algorithm
Exceeded
Time Limits
Embedded Erase Algorithm
Erase Suspend Program
DQ7
(Note1)
DQ6
DQ7
Toggle
0
0
Toggle
1
No
Toggle
Data
DQ7
DQ5
DQ3
(Note2)
DQ2
RY/ BY
N/A
No
Toggle
0
0
1
Toggle
0
0
N/A
Toggle
1
Data
Data
Data
Data
1
Toggle
0
N/A
N/A
0
0
DQ7
Toggle
1
N/A
No
Toggle
0
Toggle
1
1
Toggle
0
DQ7
Toggle
1
N/A
N/A
0
Notes:
1. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for
further details.
2. DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation has exceeded the maximum
timing limits. See “DQ5: Exceeded Timing Limits” for more information.
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
14/47
ESMT
RY/ BY :
Ready/Busy
The RY/ BY is a dedicated, open-drain output pin that
indicates whether an Embedded Algorithm is in
progress or complete. The RY/ BY status is valid after
the rising edge of the final WE pulse in the command
sequence. Since RY/ BY is an open-drain output,
several RY/ BY pins can be tied together in parallel
with a pull-up resistor to VCC.
If the output is low (Busy), the device is actively erasing
or programming. (This includes programming in the
Erase Suspend mode.) If the output is high (Ready),
the device is ready to read array data (including during
the Erase Suspend mode), or is in the standby mode.
Table 7 shows the outputs for RY/ BY .
DQ7: Data Polling
The DQ7 indicates to the host system whether an
Embedded Algorithm is in progress or completed, or
whether the device is in Erase Suspend mode. The
Data Polling is valid after the rising edge of the final
WE pulse in the program or erase command
sequence.
During the Embedded Program algorithm, the device
outputs on DQ7 the complement of the datum
programmed
to DQ7. This DQ7 status also applies to programming
during Erase Suspend. When the Embedded Program
algorithm is complete, the device outputs the true data
on DQ7. The system must provide the program address
to read valid status information on DQ7. If a program
address falls within a protected sector, Data Polling on
DQ7 is active for approximately 1 µs, then the device
returns to reading array data.
During the Embedded Erase algorithm, Data Polling
produces a “0” on DQ7. When the Embedded Erase
algorithm is complete, or if the device enters the Erase
Suspend mode, Data Polling produces a “1” on DQ7.
The system must provide an address within any of the
sectors selected for erasure to read valid status
information on DQ7.
After an erase command sequence is written, if all
sectors selected for erasing are protected, Data Polling
on DQ7 is active for approximately 100 µs, then the
device returns to reading array data. If not all selected
sectors are protected, the Embedded Erase algorithm
erases the unprotected sectors, and ignores the
selected sectors that are protected.
When the system detects DQ7 has changed from the
complement to true data, it can read valid data at DQ7~
DQ0 on the following read cycles. This is because DQ7
may change asynchronously with DQ0–DQ6 while
Elite Semiconductor Memory Technology Inc.
F49L800UA/F49L800BA
Output Enable ( OE ) is asserted low. Refer to Figure
21, Data Polling Timings (During Embedded
Algorithms), Figure 19 shows the Data Polling
algorithm.
DQ6:Toggle BIT I
Toggle Bit I on DQ6 indicates whether an Embedded
Program or Erase algorithm is in progress or complete,
or whether the device has entered the Erase Suspend
mode. Toggle Bit I may be read at any address, and is
valid after the rising edge of the final WE pulse in the
command sequence (prior to the program or erase
operation), and during the sector erase time-out.
During an Embedded Program or Erase algorithm
operation, successive read cycles to any address
cause DQ6 to toggle. The system may use either OE
or CE to control the read cycles. When the operation
is complete, DQ6 stops toggling.
When an erase command sequence is written, if all
sectors selected for erasing are protected, DQ6
toggles for approximately 100 µs, then returns to
reading array data. If not all selected sectors are
protected, the Embedded Erase algorithm erases the
unprotected sectors, and ignores the selected sectors
that are protected.
The system can use DQ6 and DQ2 together to
determine whether a sector is actively erasing or is
erase-suspended. When the device is actively erasing
(i.e. the Embedded Erase algorithm is in progress),
DQ6 toggles. When the device enters the Erase
Suspend mode, DQ6 stops toggling. However, the
system must also use DQ2 to determine which sectors
are erasing or erase-suspended. Alternatively, the
system can use DQ7.
If a program address falls within a protected sector,
DQ6 toggles for approximately 2 µs after the program
command sequence is written, then returns to reading
array data.
DQ6 also toggles during the erase-suspend-program
mode, and stops toggling once the Embedded
Program algorithm is complete. Table 7 shows the
outputs for Toggle Bit I on DQ6. Figure 20 shows the
toggle bit algorithm. Figure 22 shows the toggle bit
timing diagrams. Figure 25 shows the differences
between DQ2 and DQ6 in graphical form. Refer to the
subsection on DQ2: Toggle Bit II.
DQ2: Toggle Bit II
The “Toggle Bit II” on DQ2, when used with DQ6,
indicates whether a particular sector is actively erasing
(that is, the Embedded Erase algorithm is in progress),
or whether that sector is erase-suspended. Toggle Bit II
is valid after the rising edge of the final WE or CE ,
whichever happens first, in the command sequence.
Publication Date : May. 2007
Revision: 1.2
15/47
ESMT
DQ2 toggles when the system reads at addresses
within those sectors that have been selected for
erasure. (The system may use either OE or CE to
control the read cycles.) But DQ2 cannot distinguish
whether the sector is actively erasing or is
erase-suspended.
DQ6, by comparison, indicates whether the device is
actively erasing, or whether is in erase-suspended, but
cannot distinguish which sectors are selected for
erasure. Thus, both status bits are required for sector
and mode information. Refer to Table 7 to compare
outputs for DQ2 and DQ6.
Figure 20 shows the toggle bit algorithm in flowchart
form. See also the DQ6: Toggle Bit I subsection. Figure
22 shows the toggle bit timing diagram. Figure 25
shows the differences between DQ2 and DQ6 in
graphical form.
Reading Toggle Bits DQ6/ DQ2
Refer to Figure 20 for the following discussion.
Whenever the system initially begins reading toggle bit
status, it must read DQ7–DQ0 at least twice in a row to
determine whether a toggle bit is toggling. Typically, the
system would note and store the value of the toggle bit
after the first read. After the second read, the system
would compare the new value of the toggle bit with the
first. If the toggle bit is not toggling, the device has
completed the program or erase operation. The system
can read array data on DQ7–DQ0 on the following read
cycle.
However, if after the initial two read cycles, the system
determines that the toggle bit is still toggling, the
system should note whether the value of DQ5 is high
(see the section on DQ5). If it is, the system should
then determine again whether the toggle bit is toggling,
since the toggle bit may have stopped toggling just as
DQ5 went high. If the toggle bit is no longer toggling,
the device has successfully completed the program or
erase operation. If it is still toggling, the device did not
completed the operation successfully, and the system
must write the reset command to return to reading
array data.
The remaining scenario is that the system initially
determines that the toggle bit is toggling and DQ5 has
not gone high. The system may continue to monitor the
toggle bit and DQ5 through successive read cycles,
determining the status as described earlier.
Alternatively, it may choose to perform other system
tasks. In this case, the system must start at the
beginning of the algorithm when it returns to determine
the status of the operation.
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program or erase time has
Elite Semiconductor Memory Technology Inc.
F49L800UA/F49L800BA
exceeded the specified limits(internal pulse count).
Under these conditions DQ5 will produce a "1". This
time-out condition indicates that the program or erase
cycle was not successfully completed. Data Polling and
Toggle Bit are the only operating functions of the
device under this condition.
If this time-out condition occurs during sector erase
operation, it specifies that a particular sector is bad and
it may not be reused. However, other sectors are still
functional and may be used for the program or erase
operation. The device must be reset to use other
sectors. Write the Reset command sequence to the
device, and then execute program or erase command
sequence. This allows the system to continue to use
the other active sectors in the device.
If this time-out condition occurs during the chip erase
operation, it specifies that the entire chip is bad or
combination
of sectors are bad.
If this time-out condition occurs during the
programming operation, it specifies that the sector
containing that byte is bad and this sector may not be
reused, however other sectors are still functional and
can be reused.
The time-out condition will not appear if a user tries to
program a non blank location without erasing. Please
note that this is not a device failure condition since the
device was incorrectly used.
DQ3:Sector Erase Timer
After writing a sector erase command sequence, the
system may read DQ3 to determine whether or not an
erase operation has begun. (The sector erase timer
does not apply to the chip erase command.) If
additional sectors are selected for erasure, the entire
timeout also applies after each additional sector erase
command.
When the time-out is complete, DQ3 switches from “0”
to “1.” If the time between additional sector erase
commands from the system can be assumed to be less
than 50 µs, the system need not monitor DQ3.
When the sector erase command sequence is written,
the system should read the status on DQ7 (Data
Polling) or DQ6 (Toggle Bit I) to ensure the device has
accepted the command sequence, and then read DQ3.
If DQ3 is “1”, the internally controlled erase cycle has
begun; all further commands (except Erase Suspend)
are ignored until the erase operation is complete.
If DQ3 is “0”, the device will accept additional sector
erase commands. To ensure the command has been
accepted, the system software should check the status
of DQ3 prior to and following each subsequent sector
erase command. If DQ3 is high on the second status
check, the last command might not have been
accepted. Table 7 shows the outputs for DQ3.
Publication Date : May. 2007
Revision: 1.2
16/47
ESMT
F49L800UA/F49L800BA
7.4 More Device Operations
Hardware Data Protection
The command sequence requirement of unlock cycles for
programming or erasing provides data protection against
inadvertent writes. In addition, the following hardware
data protection measures prevent accidental erasure or
programming, which might otherwise be caused by
spurious system level signals during VCC power-up and
power-down transitions, or from system noise.
Low VCC Write Inhibit
Write cycles are inhibited by holding any one of OE =
VIL, CE = VIH or WE = VIH. To initiate a write cycle,
CE and WE must be a logical zero while OE is a
logical one.
Power Supply Decoupling
In order to reduce power switching effect, each device
should have a 0.1uF ceramic capacitor connected
between
its VCC and GND.
When VCC is less than VLKO, the device does not accept
any write cycles. This protects data during VCC power-up
and power-down. The command register and all internal
program/erase circuits are disabled, and the device
resets. Subsequent writes are ignored until VCC is
greater than VLKO. The system must provide the proper
signals to the control pins to prevent unintentional writes
when VCC is greater than VLKO.
Write Pulse "Glitch" Protection
Noise pulses of less than 5 ns (typical) on CE or WE
do not initiate a write cycle.
Power-Up Sequence
The device powers up in the Read Mode. In addition, the
memory contents may only be altered after successful
completion of the predefined command sequences.
Power-Up Write Inhibit
If WE = CE = VIL and OE = VIH during power up, the
device does not accept commands on the rising edge of
WE . The internal state machine is automatically reset to
reading array data on power-up.
Logical Inhibit
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
17/47
ESMT
F49L800UA/F49L800BA
8. ABSOLUTE MAXIMUM RATINGS
Storage Temperature
Plastic Packages . . . . . . . . . . . . . . –65°C to +150°C
Ambient Temperature
with Power Applied. . . . . . . .. . . . . . –65°C to +125°C
Voltage with Respect to Ground
VCC (Note 1) . . . . . . . . . . .–0.5 V to +4.0 V
A9, OE ,
and RESET (Note 2) …. . . .. . . . . –0.5 V to +12.5 V
All other pins (Note 1). . . . . . . . . . –0.5 V to VCC +0.5 V
Output Short Circuit Current (Note 3) .. . .. 200 mA
Notes:
1. Minimum DC voltage on input or I/O pins
is –0.5 V. During voltage transitions, input or
I/O pins may overshoot VSS to
–2.0 V for periods of up to 20 ns. See Figure 1.
Maximum DC voltage on input or I/O pins is
VCC +0.5 V. During voltage transitions, input or
I/O pins may overshoot to VCC +2.0 V for
periods up to 20 ns. See Figure 2.
2. Minimum DC input voltage on pins A9, OE ,
and RESET is -0.5 V. During voltage
transitions, A9, OE , and RESET may
overshoot VSS to –2.0 V for periods of up to 20
ns. See Figure 1. Maximum DC input voltage
on pin A9 is +12.5 V which may overshoot to
14.0 V for periods up to 20 ns.
3. No more than one output may be shorted to
ground at a time. Duration of the short circuit
should not be greater than one second.
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is
a stress rating only; functional operation of the device at
these or any other conditions above those indicated in the
operational sections of this data sheet is not implied.
Exposure of the device to absolute maximum rating
conditions for extended periods may affect device
reliability.
Figure 1. Maximum Negative Overshoot Waveform
20 n s
20 n s
+0.8V
-0.5V
-2.0V
20 n s
Figure 2. Maximum Positive Overshoot Waveform
20 n s
Vc c
+2.0V
Vc c
+0.5V
2.0V
20 n s
Elite Semiconductor Memory Technology Inc.
20 n s
Publication Date : May. 2007
Revision: 1.2
18/47
ESMT
F49L800UA/F49L800BA
OPERATING RANGES
Commercial (C) Devices Ambient Temperature (TA) . . . . . . . . . . . 0°C to +70°C
VCC Supply Voltages VCC for all devices . . . . . . . . . . . . . . . . . . . . .2.7 V to 3.6 V
Operating ranges define those limits between which the functionality of the device is guaranteed.
Table 8. Capacitance TA = 25°C , f = 1.0 MHz
Symbol
Description
Conditions
Min.
Typ.
Max.
Unit
CIN1
Input Capacitance
VIN = 0V
8
pF
CIN2
Control Pin Capacitance
VIN = 0V
12
pF
COUT
Output Capacitance
VOUT = 0V
12
pF
9. DC CHARACTERISTICS
Table 9. DC Characteristics TA = 0C to 70C, VCC = 2.7V to 3.6V
Symbol
Description
Conditions
ILI
Input Leakage Current
ILIT
ILO
ICC1
Max.
Unit
VIN = VSS or VCC, VCC = VCC max.
±1
uA
A9 Input Leakage Current
VCC = VCC max; A9=12.5V
35
uA
Output Leakage Current
VOUT = VSS or VCC, VCC = VCC max
±1
uA
VCC Active Read Current
Min.
Typ.
CE = VIL, OE = VIH
( Byte Mode )
@5MHz
9
25
mA
@1MHz
2
5
mA
CE = VIL, OE = VIH
( Word Mode )
@5MHz
9
40
mA
@1MHz
2
5
mA
ICC2
VCC Active write Current
CE = VIL, OE = VIH
20
50
mA
ICC3
VCC Standby Current
CE ; RESET = VCC ± 0.3V
25
100
uA
ICC4
VCC Standby Current
During Reset
RESET = VSS ± 0.3V
25
100
uA
ICC5
Automatic sleep mode
VIH = VCC ± 0.3V; VIL = VSS ± 0.3V
25
100
uA
VIL
Input Low Voltage(Note 1)
-0.5
0.8
V
VIH
Input High Voltage
0.7x VCC
VCC + 0.3
V
VID
Voltage for Auto-Select
and Temporary Sector
Unprotect
VCC =3.3V
11.5
12.5
V
VOL
Output Low Voltage
IOL = 4.0mA, VCC = VCC min
0.45
V
VOH1
Output High Voltage(TTL)
IOH = -2mA, VCC = VCC min
0.7x VCC
VOH2
Output High Voltage
IOH = -100uA, VCC min
VCC -0.4
VLKO
Low VCC Lock-out Voltage
2.5
V
2.3
Notes :
1. VIL min. = -1.0V for pulse width is equal to or less than 50 ns.
VIL min. = -2.0V for pulse width is equal to or less than 20 ns.
2. VIH max. = VCC + 1.5V for pulse width is equal to or less than 20 ns
If VIH is over the specified maximum value, read operation cannot be guaranteed.
3. Automatic sleep mode enable the low power mode when addresses remain stable for 250 ns
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
19/47
ESMT
F49L800UA/F49L800BA
10. AC CHARACTERISTICS
TEST CONDITIONS
Figure 3. Test Setup
2.7K
DEVICE UNDER
TEST
+3.3V
CL
DIODES = IN 3064
O R EQ U I V A L E N T
6 .2 K
C L = 1 0 0 p F I n c lu d i n g ji g c a p a c it a n c e
C L = 3 0 p F f o r F4 9 L 8 0 0 U/ BA
Figure 4. Input Waveforms and Measurement Levels
3.0V
0V
1.5V
1.5V
Test Poin t s
In p u t
Out pu t
A C TE S TIN G : In p u t s a r e d ri v e n a t 3 . 0 V f o r a l o g i c " 1 " a n d 0 V f o r a l o g i c " 0 "
In p u t p u l s e r i s e a n d f a l l t i m e s a r e < 5 n s .
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
20/47
ESMT
F49L800UA/F49L800BA
10.1 Read Operation
TA = 0C to 70C, VCC = 2.7V~3.6V
Table 10. Read Operations
Conditions
-70
-90
Symbol
Description
tRC
Read Cycle Time (Note 1)
tACC
Address to Output Delay
CE = OE = VIL
70
90
ns
tCE
CE to Output Delay
OE = VIL
70
90
ns
tOE
OE to Output Delay
CE = VIL
30
35
ns
tDF
OE High to Output Float
(Note1)
CE = VIL
25
30
ns
Min.
70
Max.
Min.
90
Max.
Unit
ns
Output Enable
Read
0
0
ns
Hold Time
Toggle and
Data Polling
10
10
ns
0
0
ns
tOEH
tOH
CE = OE = VIL
Address to Output hold
Notes :
1. Not 100% tested.
2. tDF is defined as the time at which the output achieves the open circuit condition and data is no longer
driven.
Figure 5. Read Timing Waveform
tRC
Addresses Stabl e
Addr es s
tAC C
CE
tDF
tOE
OE
tOEH
WE
tCE
tOH
High-Z
Ou t pu t s
High-Z
Output Vali d
RESET
RY/BY
0V
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
21/47
ESMT
F49L800UA/F49L800BA
10.2 Program/Erase Operation
Table 11. WE Controlled Program/Erase Operations(TA = 0C to 70C, VCC = 2.7V~3.6V)
Symbol
Description
-70
Min.
-90
Max.
Min.
Max.
Unit
tWC
Write Cycle Time (Note 1)
70
90
ns
tAS
Address Setup Time
0
0
ns
tAH
Address Hold Time
45
45
ns
tDS
Data Setup Time
35
35
ns
tDH
Data Hold Time
0
0
ns
tOES
Output Enable Setup Time
0
0
ns
Read Recovery Time Before
Write ( OE High to WE low)
0
0
ns
tCS
CE Setup Time
0
0
ns
tCH
CE Hold Time
0
0
ns
tWP
Write Pulse Width
35
35
ns
Write Pulse Width High
30
30
ns
tGHWL
tWPH
tWHWH1
Programming Operation (Note 2)
(Byte program time)
9(typ.)
9(typ.)
us
tWHWH2
Sector Erase Operation (Note 2)
0.7(typ.)
0.7(typ.)
sec
VCC Setup Time (Note 1)
50
50
us
Recovery Time from RY/ BY
0
0
ns
Program/Erase Valid to RY/ BY Delay
90
90
ns
tVCS
tRB
tbusy
Notes :
1. Not 100% tested.
2. See the "Erase and Programming Performance" section for more information.
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
22/47
ESMT
F49L800UA/F49L800BA
Table 12. CE Controlled Program/Erase Operations(TA = 0C to 70C, VCC =2.7V~3.6V)
-70
-90
Symbol
Description
tWC
Write Cycle Time (Note 1)
70
90
ns
tAS
Address Setup Time
0
0
ns
tAH
Address Hold Time
45
45
ns
tDS
Data Setup Time
35
35
ns
tDH
Data Hold Time
0
0
ns
tOES
Output Enable Setup Time
0
0
ns
tGHEL
Read Recovery Time Before Write
0
0
ns
tWS
WE Setup Time
0
0
ns
tWH
WE Hold Time
0
0
ns
tCP
CE Pulse Width
35
35
ns
tCPH
CE Pulse Width High
30
30
ns
tWHWH1
Programming Operation(note2)
9(typ.)
9(typ.)
us
tWHWH2
Sector Erase Operation (note2)
0.7(typ.)
0.7(typ.)
sec
Min.
Max.
Min.
Max.
Unit
Notes :
1. Not 100% tested.
2. See the "Erase and Programming Performance" section for more information.
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
23/47
ESMT
F49L800UA/F49L800BA
Figure 6. Write Command Timing Waveform
VCC
Addr es s
3V
VIH
ADD Valid
VIL
tAH
tAS
VIH
WE
VIL
tOES
tWP
tWPH
tCW C
CE
VIH
VIL
tCS
OE
tCH
VIH
VIL
tDS
Dat a
VIH
VIL
tDH
DIN
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
24/47
ESMT
F49L800UA/F49L800BA
Figure 7. Embedded Programming Timing Waveform
Pr ogr am C omm an d S equ en ce ( l as t t wo cycl e)
tAS
tWC
PA
PA
5 55 h
Addr es s
Read Stat us D at a ( last t w o cycl e)
PA
tAH
CE
tCH
tGHWL
OE
tW HW H1
tWP
WE
tWPH
tCS
tDS tDH
A0 h
Dat a
PD
St at u s
DOUT
tB US Y
tRB
RY/BY
tVCS
VCC
Notes :
1. PA = Program Address, PD = Program Data, DOUT is the true data the program address.
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
25/47
ESMT
F49L800UA/F49L800BA
Figure 8. Embedded Programming Algorithm Flowchart
Start
W rite Data AAH Address 555H
W rite Data 55H Address 2AAH
W rite Data A0H Address 555H
In c r e m e n t
address
W rite Program Data/Address
Data Poll
from system
No
Verify W ork OK?
Ye s
No
Last address?
Ye s
Embedded Program Completed
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
26/47
ESMT
F49L800UA/F49L800BA
Figure 9. CE Controlled Program Timing Waveform
555 for prog ram PA f or p rog r am
2AA for erase
SA for sector erase
555 for ch ip eras e
Data Pol li n g
PA
Addr es s
tWC
tAS
tAH
tWH
WE
tG HEL
OE
tCP
tWHWH1
or 2
CE
tCPH
tWS
tBUSY
tDS
tDH
Dat a
DQ7 DOUT
tRH
A0 f o r p r og r a m PD f o r p r o g r a m
30 f or sect or erase
55 for erase
10 f or ch ip erase
RESET
RY/BY
Notes :
1. PA = Program Address, PD = Program Data, DOUT = Data Out , DQ7 = complement of data written to device
2. Figure indicates the last two bus cycles of the command sequence..
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
27/47
ESMT
F49L800UA/F49L800BA
Figure 10. Embedded Chip Erase Timing Waveform
Read Statu s Dat a
Er as e Com mand Sequ en ce( last t w o cycl e)
tAS
tWC
5 55 h
2AAh
Addr es s
VA
VA
tAH
CE
tCH
tGHWL
OE
tW HW H2
tWP
WE
tWPH
tCS
tDS tDH
5 5h
Dat a
In
Progress Complete
1 0h
tBUSY
tRB
RY/BY
tVCS
VCC
Notes :
SA = Sector Address (for Sector Erase, VA = Valid Address for reading status data
(see "Write Operation Status")
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
28/47
ESMT
F49L800UA/F49L800BA
Figure 11. Embedded Chip Erase Algorithm Flowchart
Start
W rite Data AAH Address 555H
W rite Data 55H Address 2AAH
W rite Data 80H Address 555H
W rite Data AAH Address 555H
W rite Data 55H Address 2AAH
W rite Data 10H Address 555H
Data Poll from System
No
Data = FFh?
Ye s
Embedded Chip Erease Completed
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
29/47
ESMT
F49L800UA/F49L800BA
Figure 12. Embedded Sector Erase Timing Waveform
Read Statu s Dat a
Er as e Com mand Sequ en ce( last t w o cycl e)
tAS
tWC
SA
2AAh
Addr es s
VA
VA
tAH
CE
tCH
tGHWL
OE
tW HW H2
tWP
WE
tWPH
tCS
tDS tDH
55 h
Dat a
In
Progress Complete
3 0h
tRB
tBUSY
RY/BY
tVCS
VCC
Notes :
SA = Sector Address (for Sector Erase, VA = Valid Address for reading status data
(see "Write Operation Status")
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
30/47
ESMT
F49L800UA/F49L800BA
Figure 13. Embedded Sector Erase Algorithm Flowchart
Start
W rite Data AAH Address 5 55H
W rite Data 55 H Address 2AAH
W rite Data 80H Address 555H
W rite Data AAH Add ress 555H
W rit e Data 55H Address 2AAH
W rite Data 3 0H Address SA
Last Sector
to Erase
No
Yes
Data Po ll fro m System
No
Data = FFH?
Embedde d Sector Ere ase Co mplete d
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
31/47
ESMT
F49L800UA/F49L800BA
Figure 14. Erase Suspend/Erase Resume Flowchart
Start
W rite Data B0H
Tog gle Bi t c h ec kin g Q 6
not toggled
No
ERASE SUSPEND
Ye s
Read Array or
Program
Readi ng or
Pr og r am m in g En d
No
Ye s
W rite Data 30H
ERASE RESUME
Continue Erase
An oth er
Er ase Suspend?
No
Ye s
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
32/47
ESMT
F49L800UA/F49L800BA
Figure 15. In-System Sector Protect/Unprotect Timing Waveform ( RESET Control)
VID
VIH
RESET
SA,A 6
A1,A0
Valid*
Valid*
Sec t or P r ot ec t Sec tor U npr ot ec t
60 h
Dat a
6 0h
1us
Vali d*
Ver if y
4 0h
St at u s
Sector Protect = 150us
Sec t or Un p r ot ect = 15m s
CE
WE
OE
Notes :
When sector protect, A6=0, A1=1, A0=0.
When sector unprotect, A6=1, A1=1, A0=0.
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
33/47
ESMT
F49L800UA/F49L800BA
Figure 16. In-System Sector Protect/Unprotect Algorithm ( RESET = VID)
Start
Start
PLSCNT = 1
PLSCNT = 1
Protect all sector :
The indicated portion
of the sector protect
algorithm must be
performed for all
unprotected sectors
prior to issuing the
first sector
unprotect address
RESET = V I D
W ait 1μ s?
Temporary Sector
Unprotect Mode
No
RESET = V I D
W ait 1μ s?
First W rite
Cyc le = 6 0 h ?
No
First W rite
Cyc le = 6 0 h ?
Ye s
Ye s
Set up sector
address
No
Al l s ec t o r s
pr otected?
Ye s
Sector Protect :
W rite 60h to sector
address with
A6 = 0, A1 = 1,
A0 = 0
Set up first
sector address
W ait 150 μ s?
Sector Unprotect :
W rite 60h to sector
address with
A6 = 1, A1 = 1,
A0 = 0
Verify Sector
Protect : W rite 40h
to sector address
with A6 = 0,
A1 = 1, A0 = 0
In c r e m e n t
PL SC NT
Temporary Sector
Unprotect Mode
Reset
PLSCNT = 1
Read from
sector address
with A6 = 0,
A1 = 1, A0 = 0
W ait 15 ms?
Verify Sector
Unprotect : W rite
40h to sector
address with
A6 = 1, A1 = 1,
A0 =0
In c r e m e n t
PL SC NT
No
PLSCNT = 25?
Ye s
Dev ice failed
No
Data = 01h?
Read from
sector address
with A6 = 1,
A1 = 1, A0 =0
Ye s
Protect another
s e c to r ?
Ye s
No
Remove V I D
from RESET
W rite reset
command
Set up
next sector
address
No
PLSCNT
= 1000?
No
Data = 00h?
Ye s
Ye s
Dev ice failed
Last sector
v erified ?
No
Ye s
Sector Protect
Algorithm
Sector Protect
c o m p le te
Sector Unprotect
Algorithm
Remove V I D
from RESET
W rite reset
command
Sector Protect
c o m p le te
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
34/47
ESMT
F49L800UA/F49L800BA
Figure 17. Sector Protect Timing Waveform (A9, OE Control)
A0,A1
A6
12 V
3V
A9
tVLHT
12 V
3V
Ver if y
OE
tVLHT
tWPP1
tVLHT
WE
tOESP
CE
01H
Dat a
F0H
tOE
A1 8~ A1 2
Elite Semiconductor Memory Technology Inc.
Sec to r Ad dr es s
Publication Date : May. 2007
Revision: 1.2
35/47
ESMT
F49L800UA/F49L800BA
Figure 18. Sector Protection Algorithm (A9, OE Control)
Start
Set up sector address
PLSCNT = 1
OE = V ID , A9 = V ID , CE = V I L
A6 = V IL
Activ ate W E Pluse
Time out 150us
Set W E = V I H , CE = OE = V I L
A9 should remain V I D
Read from Sector
Address = SA, A0=1, A1 = 1
No
No
PLSCNT = 32?
Data = 01H?
Ye s
Dev ice Failed
Ye s
Protect Another
Sector?
Remov e VID from A9
W rite reset command
Sector Protection
C o m p l e te
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
36/47
ESMT
F49L800UA/F49L800BA
WRITE OPERATION STATUS
Figure 19. Data Polling Algorithm
Start
Read DQ7~DQ0
Add. = VA(1)
Ye s
DQ7 = Data?
No
No
D Q5 = 1?
Ye s
Read DQ7~DQ0
Add. = VA
Ye s
DQ7 = Data?
(2 )
No
FAIL
Pass
Notes :
1. VA =Valid address for programming.
2. DQ7 should be re-checked even DQ5 = "1" because
DQ7 may change simultaneously with DQ5.
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
37/47
ESMT
F49L800UA/F49L800BA
Figure 20. Toggle Bit Algorithm
Start
Read DQ7 ~ DQ0
Read DQ7 ~ DQ0
Toggle Bit = DQ6
Toggle?
(Note 1)
No
Ye s
No
D Q 5 = 1?
Ye s
Re ad D Q7 ~D Q 0 Tw ice
Toggle bit D Q6
= Tog gle?
(Note 1,2)
No
Ye s
Program / Erase operation
Not complete, write
reset command
Program / Erase
operation complete
Note :
1. Read toggle bit twice to determine whether or not it is toggle.
2. Recheck toggle bit because it may stop toggling as DQ5 change to "1".
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
38/47
ESMT
F49L800UA/F49L800BA
Figure 21. Data Polling Timings (During Embedded Algorithms)
tRC
Addr es s
VA
VA
tAC C
tCE
CE
tCH
tOE
OE
tOEH
tDF
WE
tO H
High-Z
DQ7
Complement
Complement
Tr u e
Vai l d Dat a
DQ0~DQ6
Statu s Data
Statu s Data
Tr u e
Vai l d Dat a
High-Z
tB US Y
RY/BY
Notes :
VA = Valid Address. Figure shows first status cycle after command sequence, last status read cycle, and array
data read cycle.
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
39/47
ESMT
F49L800UA/F49L800BA
Figure 22. Toggle Bit Timing Waveforms (During Embedded Algorithms)
tRC
VA
Ad dr es s
VA
VA
VA
tAC C
tCE
CE
tCH
tOE
OE
tOEH
tDF
WE
tOH
DQ6/DQ2
High-Z
tBUSY
Vai ld
Status
(fi rst re ad )
Vaild
Status
(sec ond read )
Vai ld D ata
Vaild D ata
(stops tog gling )
RY/BY
Notes :
VA = Valid Address; not required for DQ6. Figure shows first status cycle after command sequence, last status
read cycle, and array data read cycle.
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
40/47
ESMT
F49L800UA/F49L800BA
10.3 Hardware Reset Operation
Table 13. AC CHARACTERISTICS
Symbol
Description
TRH
RESET Pin Low (During Embedded Algorithms)
to Read or Write (See Note)
RESET Pin Low (NOT During Embedded
Algorithms) to Read or Write (See Note)
RESET Pulse Width (During Embedded
Algorithms)
RESET High Time Before Read(See Note)
TRB
RY/ BY Recovery Time(to CE , OE go low)
TREADY1
TREADY2
TRP
All Speed Options
Unit
Max
20
us
Max
500
ns
Min
500
ns
Min
50
ns
Min
0
ns
Notes :
Not 100% tested
Figure 23. RESET Timing Waveform
RY/BY
CE, O E
tRH
RESET
tRP
tRead y2
Reset T i mi ng NO T dur i ng Au tom at i c Al gor i th m s
tRead y1
RY/BY
tRB
CE, O E
RESET
tRP
Reset Tim ing during Automatic Algorithm s
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
41/47
ESMT
F49L800UA/F49L800BA
10.4 TEMPORARY SECTOR UNPROTECT Operation
Table 14. Temporary Sector Unprotect
Symbol
Description
TVIDR
VID Rise and Fall Time (See Note)
TRSP
RESET Setup
Unprotect
Time
for
Temporary
Sector
All Speed Options
Unit
Min
500
ns
Min
4
us
Notes:
Not 100% tested
Figure 24. Temporary Sector Unprotect Timing Diagram
12V
RESET
0 or VCC
0 or VCC
tVIDR
tVIDR
Program or Er ase Com man d Seq uence
CE
WE
tRSP
RY/BY
Figure 25. Q6 vs Q2 for Erase and Erase Suspend Operations
En ter E m bedde d
Er as in g
Er as e
S u s pe n d
WE
Enter Eras e
Suspend Program
Er as e
Su s pen d
Pr ogr am
Er as e
Resume
Er as e
Su s pen d
Read
Er as e
Er as e
Com pl et e
DQ6
DQ2
Notes :
The system can use OE or CE to toggle DQ2 / DQ6, DQ2 toggles only when read at an address within an
erase-suspended.
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
42/47
ESMT
F49L800UA/F49L800BA
Figure 26. Temporary Sector Unprotect Algorithm
Start
RESET = V ID (Note 1)
Program Erase or Program Operation
Operation Completed
RESET = V I H
Temporary Sector Unprotect Completed (Note 2)
Notes :
1. All protected status are temporary unprotect.
VID = 11.5V~12.5V
2. All previously protected sectors are protected again.
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
43/47
ESMT
F49L800UA/F49L800BA
Figure 27. ID Code Read Timing Waveform
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
44/47
ESMT
F49L800UA/F49L800BA
11. ERASE AND PROGRAMMING PERFORMANCE
Table 15. Erase And Programming Performance (Note.1)
Limits
Parameter
Unit
Typ.(2)
Max.(3)
Sector Erase Time
0.7
15
Chip Erase Time
14
Byte Programming Time
9
300
Us
Word Programming Time
11
360
Us
9
27
Sec
5.8
17
Sec
100,000
-
Cycles
20
-
Years
Chip Programming Time
Byte Mode
Word Mode
Erase/Program Cycles (1)
Data Retention
Sec
Sec
Notes:
1.Not 100% Tested, Excludes external system level over head.
2.Typical values measured at 25°C, 3.3V.
3.Maximum values measured at 85°C, 2.7V.
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
45/47
ESMT
F49L800UA/F49L800BA
12. PACKAGE DIMENSION
48-LEAD
TSOP(I) ( 12x20 mm )
A1
A2
b
Dimension in mm
Min Norm Max
------- ------- 1.20
0.05 ------- 0.15
0.95 1.00
1.05
0.17 0.22
0.27
b1
c
c1
0.17
0.10
0.10
Symbol
A
0.20
-------------
0.23
0.21
0.16
Dimension in inch
Dimension in mm
Symbol
Min Norm Max
Min Norm Max
D
------- ------- 0.047
20.00 BSC
0.006 ------- 0.002
D1
18.40 BSC
0.037 0.039 0.041
E
12.00 BSC
0.007 0.009 0.011
0.50 BSC
e
L
0.007 0.008 0.009
0.50 0.60
0.70
0.004
0.004
-------------
Elite Semiconductor Memory Technology Inc.
0.008
0.006
θ
0
O
-------
8
O
Dimension in inch
Min Norm Max
0.787 BSC
0.724 BSC
0.472 BSC
0.020 BSC
0.020
0O
0.024
-------
0.028
8O
Publication Date : May. 2007
Revision: 1.2
46/47
ESMT
F49L800UA/F49L800BA
Important Notice
All rights reserved.
No part of this document may be reproduced or duplicated in any form
or by any means without the prior permission of ESMT.
The contents contained in this document are believed to be accurate at
the time of publication. ESMT assumes no responsibility for any error in
this document, and reserves the right to change the products or
specification in this document without notice.
The information contained herein is presented only as a guide or
examples for the application of our products. No responsibility is
assumed by ESMT for any infringement of patents, copyrights, or other
intellectual property rights of third parties which may result from its use.
No license, either express , implied or otherwise, is granted under any
patents, copyrights or other intellectual property rights of ESMT or
others.
Any semiconductor devices may have inherently a certain rate of
failure. To minimize risks associated with customer's application,
adequate design and operating safeguards against injury, damage, or
loss from such failure, should be provided by the customer when
making application designs.
ESMT 's products are not authorized for use in critical applications such
as, but not limited to, life support devices or system, where failure or
abnormal operation may directly affect human lives or cause physical
injury or property damage. If products described here are to be used for
such kinds of application, purchaser must do its own quality assurance
testing appropriate to such applications.
Elite Semiconductor Memory Technology Inc.
Publication Date : May. 2007
Revision: 1.2
47/47