EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet Reverse Package Chip LED 23-215A/BHC-DN2P2E/5A Features ․Package in 8mm tape on 13〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Mono-color type. ․Pb-Free. ․The product itself will remain within RoHS compliant version. Descriptions ․The 23-215A SMD Taping is much smaller than `lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. Device Selection Guide Part No. 23-215A/BHC-DN2P2E/5A Everlight Electronics Co., Ltd. Device No. : DSE-235-002 Chip Material Emitted Color InGaN Blue http://www.everlight.com Prepared date: 6-Mar-2007 Resin Color Water Clear Rev. 2 Page: 1 of 10 Prepared by: Jay Chou EVERLIGHT ELECTRONICS CO.,LTD. 23-215A/BHC-DN2P2E/5A Package Outline Dimensions 0.2 0.6 0.8±0.05 3.2 2.0 1.2 1.0 0.6 2.0 2.0 1.0 0.6 Cathode Mark Note: The tolerances unless mentioned is ±0.1mm,Unit = mm Everlight Electronics Co., Ltd. Device No. : DSE-235-002 http://www.everlight.com Prepared date: 6-Mar-2007 Rev. 2 Page: 2 of 10 Prepared by: Jay Chou EVERLIGHT ELECTRONICS CO.,LTD. 23-215A/BHC-DN2P2E/5A Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA Peak Forward Current (Duty 1/10 @1KHz) IFP 100 mA Power Dissipation Pd 110 mW Electrostatic Discharge(HBM) ESD 150 V Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ Soldering Temperature Tsol Reflow Soldering : 260 ℃ for 10 sec. Hand Soldering : 350 ℃ for 3 sec. Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Min. Typ. Max. Unit Luminous Intensity Iv 36 ---- 72 mcd Peak Wavelength λp ---- 468 ---- nm λd 466 ---- 472 nm Dominant Wavelength Spectrum Radiation Bandwidth △λ ---- 35 ---- nm Viewing Angle 2θ1/2 ---- 130 ---- deg Forward Voltage VF 2.75 ---- 3.65 V Reverse Current IR ---- ---- 50 μA Condition IF=20mA VR=5V Notes: 1.Tolerance of Luminous Intensity ±11% 2.Tolerance of Dominant Wavelength ±1nm 3.Tolerance of Forward Voltage ±0.1V Everlight Electronics Co., Ltd. Device No. : DSE-235-002 http://www.everlight.com Prepared date: 6-Mar-2007 Rev. 2 Page: 3 of 10 Prepared by: Jay Chou EVERLIGHT ELECTRONICS CO.,LTD. 23-215A/BHC-DN2P2E/5A Bin Range Of Dom. Wavelength Group D Bin Min Max AA2 466 468 AA3 468 470 AA4 470 472 Unit Condition nm IF=20mA Bin Range Of Luminous Intensity Bin Min Max N2 36 45 P1 45 57 P2 57 72 Unit Condition mcd IF=20mA Bin Range Of Forward Voltage Group E Bin Min Max 5 2.75 3.05 6 3.05 3.35 7 3.35 3.65 Unit Condition V IF=20mA Notes: 1.Tolerance of Luminous Intensity ±11% 2.Tolerance of Dominant Wavelength ±1nm 3.Tolerance of Forward Voltage ±0.1V Everlight Electronics Co., Ltd. Device No. : DSE-235-002 http://www.everlight.com Prepared date: 6-Mar-2007 Rev. 2 Page: 4 of 10 Prepared by: Jay Chou EVERLIGHT ELECTRONICS CO.,LTD. 23-215A/BHC-DN2P2E/5A Typical Electro-Optical Characteristics Curves Everlight Electronics Co., Ltd. Device No. : DSE-235-002 http://www.everlight.com Prepared date: 6-Mar-2007 Rev. 2 Page: 5 of 10 Prepared by: Jay Chou EVERLIGHT ELECTRONICS CO.,LTD. 23-215A/BHC-DN2P2E/5A Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank REF: Forward Voltage Rank MSL-2 Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No. : DSE-235-002 http://www.everlight.com Prepared date: 6-Mar-2007 Rev. 2 Page: 6 of 10 Prepared by: Jay Chou EVERLIGHT ELECTRONICS CO.,LTD. 23-215A/BHC-DN2P2E/5A Carrier Tape Dimensions: Loaded quantity 5000 PCS per reel Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moisture-proof bag Everlight Electronics Co., Ltd. Device No. : DSE-235-002 Desiccant http://www.everlight.com Prepared date: 6-Mar-2007 Label Rev. 2 Page: 7 of 10 Prepared by: Jay Chou EVERLIGHT ELECTRONICS CO.,LTD. 23-215A/BHC-DN2P2E/5A Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% No. Items 1 Reflow Soldering 2 Temperature Cycle 3 Thermal Shock 4 5 6 7 High Temperature Storage Low Temperature Storage DC Operating Life High Temperature / High Humidity Everlight Electronics Co., Ltd. Device No. : DSE-235-002 Test Condition Temp. : 260℃±5℃ Min. 5sec. H : +100℃ 15min ∫ 5 min L : -40℃ 15min H : +100℃ 5min ∫ 10 sec L : -10℃ 5min Temp. : 100℃ Temp. : -40℃ Test Sample Hours/Cycles Size Ac/Re 6 Min. 22 PCS. 0/1 300 Cycles 22 PCS. 0/1 300 Cycles 22 PCS. 0/1 22 PCS. 0/1 22 PCS. 0/1 1000 Hrs. 1000 Hrs. IF = 20 mA 1000 Hrs. 22 PCS. 0/1 85℃/ 85%RH 1000 Hrs. 22 PCS. 0/1 http://www.everlight.com Prepared date: 6-Mar-2007 Rev. 2 Page: 8 of 10 Prepared by: Jay Chou EVERLIGHT ELECTRONICS CO.,LTD. 23-215A/BHC-DN2P2E/5A Precautions For Use 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less. If unused LEDs remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 1~5 °C / Sec. 260°C. Max. 10 Sec. Max. 1~5 °C / Sec. Pre-heating 180~200°C 60 Sec. Max. Above 220°C 120 Sec. Max. 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. Device No. : DSE-235-002 http://www.everlight.com Prepared date: 6-Mar-2007 Rev. 2 Page: 9 of 10 Prepared by: Jay Chou EVERLIGHT ELECTRONICS CO.,LTD. 23-215A/BHC-DN2P2E/5A 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Everlight Electronics Co., Ltd. Device No. : DSE-235-002 Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com http://www.everlight.com Prepared date: 6-Mar-2007 Rev. 2 Page: 10 of 10 Prepared by: Jay Chou