EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet Infrared Remote-Control Receiver Module IRM-26xx-DIP-A SERIES Features : ‧High protection ability against EMI . ‧Circular lens to improve the receive characteristic. ‧Line-up for various center carrier frequencies. ‧Low voltage and low power consumption. ‧Side-Received DIP Type. ‧High immunity against ambient light. ‧Photodiode with integrated circuit. ‧TTL and CMOS compatibility. ‧Long reception distance. ‧High sensitivity. ‧Suitable burst length ≧10 pulses/burst. ‧The product itself will remain within RoHS compliant version. ‧Pb free Descriptions The IRM-26xx-DIP-A SERIES are miniaturized receivers for infrared remote control systems. PIN diode and preamplifier are assembled on lead frame, the epoxy package is designed as IR filter. The demodulated output signal can directly be decoded by a microprocessor. IRM-26xx-DIP-A SERIES is the standard IR remote control receiver series, supporting all major transmission codes. Applications 1. Light detecting portion of remote control ․AV instruments such as Audio, TV, VCR, CD, MD, etc. ․Home appliances such as Air-conditioner, Fan , etc. ․The other equipments with wireless remote control. ․CATV set top boxes ․Multi-media Equipment PART MATERIAL COLOR Chip Silicon --- Compound Epoxy Black Everlight Electronics Co., Ltd. http:\\www.everlight.com Device No：DMO-026-392 Prepared date：10-22-2005 Rev 1 Prepared by： Page: 1 of 9 Cindy Lin EVERLIGHT ELECTRONICS CO.,LTD. IRM-26xx-DIP-A SERIES Package Dimensions OUT GND Vcc Notes: 1.All dimensions are in millimeters. 2.Tolerances unless dimensions ±0.3mm. Available Types For Different Carrier Frequencies Type Carrier Frequencies (Typ) IRM-2633-DIP-A 33 kHz IRM-2638-DIP-A 38 kHz IRM-2640-DIP-A 40 kHz IRM-2656-DIP-A 56 kHz PCB Layout for Electrical Circuit Everlight Electronics Co., Ltd. http:\\www.everlight.com Device No：DMO-026-392 Prepared date：10-22-2005 Rev 1 Prepared by： Page: 2 of 9 Cindy Lin EVERLIGHT ELECTRONICS CO.,LTD. IRM-26xx-DIP-A SERIES Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Supply Voltage Vcc 0~6 V Operating Temperature Topr -25 ~ +80 ℃ Storage Temperature Tstg -40 ~ +85 ℃ Soldering Temperature Tsol 260 ℃ Notice 4mm from mold body less than 10 seconds Recommended Operating Condition Supply Voltage Rating: Vcc =4.5V to 5.5V Electro-Optical Characteristics (Ta=25℃, and Vcc=5 V) Parameter Symbol MIN. TYP. MAX. Unit Condition Consumption Current Icc --- 1.2 --- mA No signal input Peak Wavelength λp --- 940 --- nm L0 14 --- --- L45 6 --- --- Half Angle(Horizontal) Θh --- 45 --- deg Half Angle(Vertical) Θv --- 45 --- deg High Level Pulse Width TH 400 --- 800 μs Low Level Pulse Width TL 400 --- 800 μs High Level Output Voltage VH 4.5 --- --- V Low Level Output Voltage VL --- 0.2 0.5 V Reception Distance m At the ray axis *1 At the ray axis *2 *1:The ray receiving surface at a vertex and relation to the ray axis in the range of θ= 0° and θ=45°. *2:A range from 30cm to the arrival distance. Average value of 50 pulses. Everlight Electronics Co., Ltd. http:\\www.everlight.com Device No：DMO-026-392 Prepared date：10-22-2005 Rev 1 Prepared by： Page: 3 of 9 Cindy Lin EVERLIGHT ELECTRONICS CO.,LTD. IRM-26xx-DIP-A SERIES The Notice of Application: Transmission remote control signal consist of four parts: Encode Part, IR Transmitter Source, IRM device, Decode Part 1. When IRM-26xx code select frequency, it need to well understand the center system of encode part. 2. Strong or weak light of IR Transmitter can affect distance of transmission. 3. Minimum Burst Length Tburst (number of pulses per burst) : 10 cycles 4. It needs to ensure the translation range of decode part if it is applied to the pulse-width range. If the above items hardly assure of its application, it’ll cause NG(no good) message from the edge of signal. Test Method： The specified electro-optical characteristics is satisfied under the following Conditions at the controllable distance. cMeasurement place A place that is nothing of extreme light reflected in the room. dExternal light Project the light of ordinary white fluorescent lamps which are not high Frequency lamps and must be less then 10 Lux at the module surface. (Ee≦10Lux) eStandard transmitter A transmitter whose output is so adjusted as to Vo=400mVp-p and the output Wave form shown in Fig.-1.According to the measurement method shown in Fig.-2 the standard transmitter is specified. However , the infrared photodiode to be used for the transmitter should be λp=940nm,Δλ=50nm. Also, photodiode is used of PD438B(Vr=5V). (Standard light / Light source temperature 2856°K). fMeasuring system According to the measuring system shown in Fig.-3 Fig.-1 Transmitter Wave Form D.U.T output Pulse Carrier frequency is adjusted to center frequency of each product. IR TANSMITTER OUTPUT WAVE FORM OUTPUT PULSE OF DEVICE Duty=0.5 Everlight Electronics Co., Ltd. http:\\www.everlight.com Device No：DMO-026-392 Prepared date：10-22-2005 Rev 1 Prepared by： Page: 4 of 9 Cindy Lin EVERLIGHT ELECTRONICS CO.,LTD. IRM-26xx-DIP-A SERIES Fig.-2 Measuring Method Fig.-3 Measuring System 20cm 10k +5.0± 0.1V L: Transmission Distance Vcc OUT θ θ 10uF D.U.T Standard Transmitter Vout Standard Transmitter Vout 100k GND θ: Angle Of Horizontal & Vertical Direction Oscilloscope Block Diagram： VCC Noise Det.& Gain Ctrl. IN I-V Converter &Input Bias Control Pre Amp AGC Amp Voltage Reference Circuit Band-pass Fiter Limit Amp Integrator &Wave Shaping Comparator Output Stage Fset Bias Circuit Frequency Setting Frequency Trimming Threshold Control Circuit GND Application Circuit： RC Filter should be connected closely between Vcc pin and GND pin. Everlight Electronics Co., Ltd. http:\\www.everlight.com Device No：DMO-026-392 Prepared date：10-22-2005 Rev 1 Prepared by： Page: 5 of 9 Cindy Lin OUT EVERLIGHT ELECTRONICS CO.,LTD. IRM-26xx-DIP-A SERIES Typical Electro-Optical Characteristics Curves Fig.-4 Relative Spectral Sensitivity vs. Wavelength Fig.-5 Relative Transmission Distance vs. Direction θ Fig.-7 Arrival Distance vs. Supply Voltage 17.5 17.0 14.0 14.0 Transmission Distance Lc (m) Transmission Distance Lc (m) Fig.-6 Arrival Distance vs. Ambient Temperature 10.5 7.0 3.5 10.5 7.0 3.5 Supply Voltage Vcc (V) Ambient Temperature Ta (°C) Everlight Electronics Co., Ltd. http:\\www.everlight.com Device No：DMO-026-392 Prepared date：10-22-2005 Rev 1 Prepared by： Page: 6 of 9 Cindy Lin EVERLIGHT ELECTRONICS CO.,LTD. IRM-26xx-DIP-A SERIES Typical Electro-Optical Characteristics Curves Relative Transmission Distance (%) Relative Transmission Distance (%) Fig.-8 Relative Transmission Distance vs. Center Carrier Frequency IRM-2633 IRM-2638 Center Carrier Frequency (kHz) Center Carrier Frequency (kHz) Relative Transmission Distance (%) Relative Transmission Distance (%) Fig.-8 Relative Transmission Distance vs. Center Carrier Frequency IRM-2640 IRM-2656 Center Carrier Frequency (kHz) Center Carrier Frequency (kHz) Output Pulse Width (μsec) Fig.-9 Relative Transmission Distance vs. Center Carrier Frequency Transmission Distance Lc (m) Everlight Electronics Co., Ltd. http:\\www.everlight.com Device No：DMO-026-392 Prepared date：10-22-2005 Rev 1 Prepared by： Page: 7 of 9 Cindy Lin EVERLIGHT ELECTRONICS CO.,LTD. IRM-26xx-DIP-A SERIES █ Reliability Test Item And Condition The reliability of products shall be satisfied with items listed below. Confidence level: 90% LTPD: 10% Test Items Test Conditions Failure Judgement Criteria Samples(n) Defective(c) 1 cycle Temperature cycle -40℃ +25℃ +85℃ (30min)(5min)(30min) 300 cycle test Temp: +85℃ High temperature test Vcc:5V 1000hrs Low temperature storage n=22,c=0 n=22,c=0 L0≦ L×0.8 L45≦ L×0.8 Temp: -40℃ 1000hrs n=22,c=0 High temperature High humidity Ta: 85℃,RH: 85% 1000hrs Solder heat Temp: 260±5℃ 10sec 4mm From the bottom of the package. Everlight Electronics Co., Ltd. http:\\www.everlight.com Device No：DMO-026-392 Prepared date：10-22-2005 L: Lower specification limit n=22,c=0 n=22,c=0 Rev 1 Prepared by： Page: 8 of 9 Cindy Lin EVERLIGHT ELECTRONICS CO.,LTD. IRM-26xx-DIP-A SERIES Packing Quantity Specification 1. 160PCS/1Box 2. 10Boxes/1Carton Label Form Specification CPN: Customer’s Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks HUE: None REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place IRM-26xx-DIP-A Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s consent. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http:\\www.everlight.com Everlight Electronics Co., Ltd. http:\\www.everlight.com Device No：DMO-026-392 Prepared date：10-22-2005 Rev 1 Prepared by： Page: 9 of 9 Cindy Lin