Technical Data Sheet Reverse Package Infrared LED SIR23-21C/TR8 Features ․Small double-end package ․Low forward voltage ․Good spectral matching to Si photo detector ․Package in 8mm tape on 7” diameter reel ․Pb free ․The product itself will remain within RoHS complaint version Descriptions SIR23-21C/TR8 is an infrared emitting diode in miniature SMD package molded in a water clear plastic with flat top View lens The device is spectrally matched with silicon photodiode and phototransistor. Applications ․Household Appliances ․Electric Appliances ․Smoke detector ․Floppy disk drive Device Selection Guide LED Part No. Chip Material Lens Color SIR GaAlAs Water clear Everlight Electronics Co., Ltd. Device No：SZDTS-023-001 http:\\www.everlight.com Prepared date：30-Aug-2005 Rev 1 Page: 1 of 10 Prepared by：bian changyou SIR23-21C/TR8 Package Dimensions + Polarity Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions ±0.1mm Everlight Electronics Co., Ltd. Device No：SZDTS-023-001 http:\\www.everlight.com Prepared date：30-Aug-2005 Rev 1 Page: 2 of 10 Prepared by：bian changyou SIR23-21C/TR8 Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Continuous Forward Current IF 65 Units mA Reverse Voltage VR 5 V Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +85 ℃ Power Dissipation at(or below) 25℃Free Air Temperature Pd 110 mW Soldering Temperature Tsol Reflow Soldering : 260 ℃ for 10 sec. Hand Soldering : 350 ℃ for 3 sec. Notes: *1. Soldering time≦5 seconds. Electro-Optical Characteristics (Ta=25℃) Parameter Radiant Intensity Peak Wavelength Spectral Bandwidth Forward Voltage Symbol Ee λp Condition IF=20mA Min. Typ. Max. 0.20 0.80 IF=20mA -- 875 --- 80 -- Δλ IF=20mA VF View Angle IR 2θ1/2 Everlight Electronics Co., Ltd. Device No：SZDTS-023-001 nm IF=20mA -- 1.3 1.6 IF=100mA -- 1.4 1.8 VR=5V -- -- 10 IF=20mA -- 160 -- Pulse Width≦100μs ,Duty≦1% Reverse Current -- http:\\www.everlight.com Prepared date：30-Aug-2005 Units mW /sr nm Rev 1 V μA deg Page: 3 of 10 Prepared by：bian changyou SIR23-21C/TR8 Typical Electro-Optical Characteristics Curves Fig.1 Forward Current vs. Ambient Temperature Fig.2 Spectral Distribution 140 100 IF=20mA Ta=25° C 120 80 100 60 80 60 40 40 20 20 0 -40 -20 0 20 40 60 80 Fig.3 Peak Emission Wavelength Ambient Temperature 100 0 810 835 855 875 905 925 945 965 985 Fig.4 Forward Current vs. Forward Voltage 4 10 920 900 3 10 875 2 10 860 840 -25 1 10 0 25 Everlight Electronics Co., Ltd. Device No：SZDTS-023-001 50 75 100 0 http:\\www.everlight.com Prepared date：30-Aug-2005 1 2 Rev 1 3 4 Page: 4 of 10 Prepared by：bian changyou SIR23-21C/TR8 Typical Electro-Optical Characteristics Curves Fig.5 Relative Intensity vs. Fig.6 Relative Radiant Intensity vs. Forward Current Angular Displacement -20 Ie-Radiant Intensity(mW/sr) 100 -10 0 10 20 30 10 1 0 10 0 10 1 2 10 10 3 1.0 40 0.9 50 0.8 0.7 60 70 80 10 4 0.6 0.4 0.2 0 0.2 0.4 0.6 IF-Forward Current (mA) Fig.7 Relative Intensity vs. Fig.8 Forward Voltage vs. Ambient Temperature(°C) Ambient Temperature(°C) 1.4 1.0 0.8 1.3 IF=20mA 0.6 IF=20mA 1.2 0.4 25 50 75 Everlight Electronics Co., Ltd. Device No：SZDTS-023-001 100 120 1.1 25 http:\\www.everlight.com Prepared date：30-Aug-2005 50 75 Rev 1 100 120 Page: 5 of 10 Prepared by：bian changyou SIR23-21C/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 60%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. Device No：SZDTS-023-001 http:\\www.everlight.com Prepared date：30-Aug-2005 Rev 1 Page: 6 of 10 Prepared by：bian changyou SIR23-21C/TR8 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. Everlight Electronics Co., Ltd. Device No：SZDTS-023-001 http:\\www.everlight.com Prepared date：30-Aug-2005 Rev 1 Page: 7 of 10 Prepared by：bian changyou SIR23-21C/TR8 Reliability Test Item And Condition The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% NO. Item Test Conditions Test Hours/ Sample Cycles Sizes 1 REFLOW Soldering TEMP.：260℃±5℃ 6Mins 5secs 15mins 50Cycles 2 Temperature Cycle H : +100℃ 5mins L : -40℃ 15mins 3 Thermal Shock H :+100℃ 4 High Temperature Storage TEMP.：+100℃ 5 Low Temperature Storage TEMP.：-40℃ 6 DC Operating Life IF=20mA 7 High Temperature/ 85℃ / 85% R.H Ac/Re 22pcs 0/1 22pcs IR≧U×2 Ee≦L×0.8 VF≧U×1.2 0/1 22pcs U：Upper 0/1 22pcs Specification Limit L：Lower 0/1 1000hrs 22pcs Specification Limit 0/1 1000hrs 22pcs 0/1 1000hrs 22pcs 0/1 5mins 50Cycles 10secs 5mins L :-10℃ Failure Judgement Criteria 1000hrs High Humidity Everlight Electronics Co., Ltd. Device No：SZDTS-023-001 http:\\www.everlight.com Prepared date：30-Aug-2005 Rev 1 Page: 8 of 10 Prepared by：bian changyou SIR23-21C/TR8 Package Dimensions Taping Dimensions Note: The tolerances unless mentioned is ±0.1mm, Unit = mm Everlight Electronics Co., Ltd. Device No：SZDTS-023-001 http:\\www.everlight.com Prepared date：30-Aug-2005 Rev 1 Page: 9 of 10 Prepared by：bian changyou SIR23-21C/TR8 Packing Quantity Specification 1.2000Pcs/1Volume，1Volume/1Bag 2.10Boxes/1Carton Label Form Specification CPN: Customer’s Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks HUE: Peak Wavelength REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place xxxxxx xxxxxx RoHS xxxxxxxxxxxx xxxx xxxxxxxx Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s consent. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Everlight Electronics Co., Ltd. Device No：SZDTS-023-001 Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http:\\www.everlight.com http:\\www.everlight.com Prepared date：30-Aug-2005 Rev 1 Page: 10 of 10 Prepared by：bian changyou