HANBit HSD4M64D4B Synchronous DRAM Module 32Mbyte (4Mx64-Bit), DIMM, 4Banks, 4K Ref., 3.3V Part No. HSD4M64D4B GENERAL DESCRIPTION The HSD4M64D4B is a 4M x 64 bit Synchronous Dynamic RAM high density memory module. The module consists of four CMOS 1M x 16 bit with 4banks Synchronous DRAMs in TSOP-II 400mil packages on a 168-pin glass-epoxy substrate. Two 0.1uF decoupling capacitors are mounted on the printed circuit board in parallel for each SDRAM. The HSD4M64D4B is a DIMM(Dual in line Memory Module) and is intended for mounting into 168-pin edge connector sockets. Synchronous design allows precise cycle control with the use of system clock. I/O transactions are possible on every clock cycle. Range of operating frequencies, programmable latencies allows the same device to be useful for a variety of high bandwidth, high performance memory system applications All module components may be powered from a single 3.3V DC power supply and all inputs and outputs are LVTTL-compatible. FEATURES • Part Identification HSD4M64D4B-10 : 100MHz ( CL=2) HSD4M64D4B-10L : 100MHz ( CL=3) HSD4M64D4B- 8 : 125MHz ( CL=3) • Burst mode operation • Auto & self refresh capability (4096 Cycles/64ms) • LVTTL compatible inputs and outputs • Single 3.3V ±0.3V power supply • MRS cycle with address key programs - Latency (Access from column address) - Burst length (1, 2, 4, 8 & Full page) - Data scramble (Sequential & Interleave) • JEDEC standard • All inputs are sampled at the positive going edge of the system clock • The used device is 1Mx16Bitx4Banks SDRAM URL:www.hbe.co.kr REV.1.0 (August.2002) -1- HANBit Electronics Co.,Ltd HANBit HSD4M64D4B PIN ASSIGNMENT PIN Symbol PIN Symbol PIN Symbol PIN Symbol PIN Symbol PIN Symbol 1 Vss 29 DQM1 57 DQ18 2 DQ0 30 /CS0 58 DQ19 85 Vss 113 DQM5 141 DQ50 86 DQ32 114 NC 142 DQ51 3 DQ1 31 DU 59 Vcc 87 DQ33 115 /RAS 143 Vcc 4 DQ2 32 Vss 5 DQ3 33 A0 60 DQ20 88 DQ34 116 Vss 144 DQ52 61 NC 89 DQ35 117 A1 145 NC 6 Vcc 34 A2 7 DQ4 35 A4 62 NC 90 Vcc 118 A3 146 NC 63 CKE1 91 DQ36 119 A5 147 NC 8 DQ5 36 A6 64 Vss 92 DQ37 120 A7 148 Vss 9 DQ6 37 A8 65 DQ21 93 DQ38 121 A9 149 DQ53 10 DQ7 38 A10 66 DQ22 94 DQ39 122 BA0 150 DQ54 11 DQ8 39 BA1 67 DQ23 95 DQ40 123 A11 151 DQ55 12 Vss 40 Vcc 68 Vss 96 Vss 124 Vcc 152 Vss 13 DQ9 41 Vcc 69 DQ24 97 DQ41 125 CLK1 153 DQ56 14 DQ10 42 CLK0 70 DQ25 98 DQ42 126 NC 154 DQ57 15 DQ11 43 Vss 71 DQ26 99 DQ43 127 Vss 155 DQ58 16 DQ12 44 NC 72 DQ27 100 DQ44 128 CKE0 156 DQ59 17 DQ13 45 /CS2 73 Vcc 101 DQ45 129 NC 157 Vcc 18 Vcc 46 DQM2 74 DQ28 102 Vcc 130 DQM6 158 DQ60 19 DQ14 47 DQM3 75 DQ29 103 DQ46 131 DQM7 159 DQ61 20 DQ15 48 NC 76 DQ30 104 DQ47 132 NC 160 DQ62 21 NC 49 Vcc 77 DQ31 105 NC 133 Vcc 161 DQ63 22 NC 50 NC 78 Vss 106 NC 134 NC 162 Vss 23 Vss 51 NC 79 CLK2 107 Vss 135 NC 163 CLK3 24 NC 52 NC 80 NC 108 NC 136 NC 164 NC 25 NC 53 NC 81 WP 109 NC 137 NC 165 SA0 26 Vcc 54 Vss 82 SDA 110 Vcc 138 Vss 166 SA1 27 /WE 55 DQ16 83 SCL 111 /CAS 139 DQ48 167 SA2 28 DQM0 56 DQ17 84 Vcc 112 DQM4 140 DQ49 168 Vcc PIN NAMES Pin Name Function Pin Name Function A0 ~ A11 Address input (Multiplexed) BA0 ~ BA1 Select bank DQ0 ~ DQ63 Data input/output CLK0 ~ CLK3 Clock input CKE0 ~ CKE1 Clock enable input CS0 Chip select input /RAS Row address strobe /CAS Column address strobe /WE Write enable DQM0 ~ 7 DQM Vcc Power supply (3.3V) Vss Ground SDA Serial data I/O SCL Serial clock DU Do□ ¢ t use NC No connection URL:www.hbe.co.kr REV.1.0 (August.2002) -2- HANBit Electronics Co.,Ltd HANBit HSD4M64D4B FUNCTIONAL BLOCK DIAGRAM DQ0-63 CKE0 /CAS CKE CAS /RAS RAS /CS0 CE U1 WE CKE CAS A0-A11 BA0-1 CE CKE CAS A0-A11 BA0-1 DQM0 DQM1 WE CKE CAS A0-A11 DQM2 DQM3 DQM3 CLKC CLK DQ32-47 U3 RAS BA0-1 DQM4 DQM4 DQM5 DQM5 CLK DQ48-63 U4 RAS CE DQM0 DQM1 DQM2 WE CE CLKA CLK DQ16-31 U2 RAS /CS2 CLK DQ0-15 DQM6 WE A0-A11 BA0-1 DQM6 DQM7 DQM7 /WE A0 – A11 BA0-1 Vcc Two 0.1uF Capacitors per each SDRAM Vss PIN FUNCTION DESCRIPTION Pin Name CLK System clock /CE Chip enable Input Function Active on the positive going edge to sample all inputs. Disables or enables device operation by masking or enabling all inputs except CLK, CKE and DQM Masks system clock to freeze operation from the next clock cycle. CKE should be enabled at least one cycle prior to new command. CKE Clock enable Disable input buffers for power down in standby. CKE should be enabled 1CLK+tSS prior to valid command. URL:www.hbe.co.kr REV.1.0 (August.2002) -3- HANBit Electronics Co.,Ltd HANBit HSD4M64D4B Row/column addresses are multiplexed on the same pins. A0 ~ A11 Address Row address : RA0 ~ RA11, Column address : CA0 ~ CA8 Selects bank to be activated during row address latch time. BA0 ~ BA1 Bank select address Selects bank for read/write during column address latch time. Latches row addresses on the positive going edge of the CLK with RAS low. /RAS Row address strobe Enables row access & precharge. Column address Latches column addresses on the positive going edge of the CLK with CAS low. /CAS strobe Enables column access. Enables write operation and row precharge. /WE Write enable Latches data in starting from CAS, WE active. Data input/output Makes data output Hi-Z, tSHZ after the clock and masks the output. DQM0 ~ 7 mask DQ0 ~ 63 Blocks data input when DQM active. (Byte masking) Data input/output Power Data inputs/outputs are multiplexed on the same pins. Power and ground for the input buffers and the core logic. Vcc/Vss supply/ground ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL RATING VIN ,OUT -1V to 4.6V Voltage on Vcc Supply Relative to Vss Vcc -1V to 4.6V Power Dissipation PD 4W TSTG -55oC to 150oC Voltage on Any Pin Relative to Vss Storage Temperature Short Circuit Output Current IOS 50mA Notes: Permanent device damage may occur if " Absolute Maximum Ratings" are exceeded. Functional operation should be restricted to the conditions as detailed in the operational sections of this data sheet. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. DC OPERATING CONDITIONS (Recommended operating conditions (Voltage referenced to VSS = 0V, TA = 0 to 70°C) ) PARAMETER SYMBOL MIN TYP. MAX UNIT Supply Voltage Vcc 3.0 3.3 3.6 V Input High Voltage VIH 2.0 3.0 Vcc+0.3 V 1 Input Low Voltage VIL -0.3 0 0.8 V 2 Output High Voltage VOH 2.4 - - V IOH = -2mA Output Low Voltage VOL -4 - 4 V IOL = 2mA Input leakage current I IL -1.5 - 1.5 uA 3 URL:www.hbe.co.kr REV.1.0 (August.2002) -4- NOTE HANBit Electronics Co.,Ltd HANBit HSD4M64D4B Notes : 1. VIH (max) = 5.6V AC. The overshoot voltage duration is ≤ 3ns. 2. VIL (min) = -2.0V AC. The undershoot voltage duration is ≤ 3ns. 3. Any input 0V ≤ VIN ≤ VDDQ. Input leakage currents include Hi-Z output leakage for all bi-directional buffers with Tri-State outputs. CAPACITANCE (VCC = 3.3V, TA = 23°C, f = 1MHz, VREF =1.4V ± 200 mV) DESCRIPTION SYMBOL MIN MAX UNITS CCLK 15 25 pF CIN 30 40 pF Address CADD 30 40 pF DQ (DQ0 ~ DQ15) COUT 5 15 pF Clock /RAS, /CAS,/WE,/CS, CKE, L(U)DQM DC CHARACTERISTICS (Recommended operating condition unless otherwise noted, TA = 0 to 70°C) TEST PARAMETER VERSION SYMBOL CONDITION 80 10 10L 300 280 280 UNIT NOTE mA 1 Burst length = 1 Operating current ICC1 (One bank active) tRC ≥ tRC(min) IO = 0mA Precharge standby current in ICC2P power-down mode ICC2PS CKE ≤ VIL(max) 4 mA 4 mA tCC=10ns CKE & CLK ≤ VIL(max) tCC=∞ CKE ≥ VIH(min) ICC2N CS* ≥ VIH(min), tCC=10ns 48 Input signals are changed Precharge standby current in one time during 20ns non power-down mode mA CKE ≥ VIH(min) ICC2NS CLK ≤ VIL(max), tCC=∞ 24 Input signals are stable Active standby current power-down mode URL:www.hbe.co.kr REV.1.0 (August.2002) in ICC3P ICC3PS CKE ≤ VIL(max), tCC=10ns CKE&CLK ≤ VIL(max) 8 mA 8 tCC=∞ -5- HANBit Electronics Co.,Ltd HANBit HSD4M64D4B CKE≥VIH(min), ICC3N Active standby current in CS*≥VIH(min), tCC=10ns non power-down mode one time during 20ns (One bank active) CKE≥VIH(min) ICC3NS 80 Input signals are changed CLK ≤VIL(max), mA tCC=∞ 40 Input signals are stable IO = 0 mA Operating current Page burst ICC4 (Burst mode) 380 300 300 mA 1 500 mA 2 4 mA 4Banks Activated tCCD = 2CLKs Refresh current ICC5 Self refresh current ICC6 tRC ≥ tRC(min) CKE ≤ 0.2V Notes : 1. Measured with outputs open. 2. Refresh period is 64ms. AC OPERATING TEST CONDITIONS (vcc = 3.3V ± 0.3V, TA = 0 to 70°C) PARAMETER Value UNIT 2.4/0.4 V 1.4 V tr/tf = 1/1 ns 1.4 V AC Input levels (Vih/Vil) Input timing measurement reference level Input rise and fall time Output timing measurement reference level Output load condition See Fig. 2 +3.3V Vtt=1.4V 1200Ω 50Ω DOUT 870Ω DOUT 50pF* Z0=50Ω 50pF VOH (DC) = 2.4V, IOH = -2mA VOL (DC) = 0.4V, IOL = 2mA (Fig. 2) AC output load circuit (Fig. 1) DC output load circuit URL:www.hbe.co.kr REV.1.0 (August.2002) -6- HANBit Electronics Co.,Ltd HANBit HSD4M64D4B OPERATING AC PARAMETER (AC operating conditions unless otherwise noted) VERSION PARAMETER SYMBOL -80 -10 -10L UNIT NOTE Row active to row active delay tRRD(min) 16 20 20 ns 1 RAS to CAS delay tRP(min) 20 20 20 ns 1 Row precharge time tRP(min) 20 20 20 ns 1 tRAS(min) 48 50 50 ns 1 Row active time tRAS(max) Row cycle time 100 tRC(min) 68 ns 70 70 ns 1 Last data in to row precharge tRDL(min) 1 CLK 2 Last data in to new col. address delay tCDL(min) 1 CLK 2 Last data in to burst stop tBDL(min) 1 CLK 2 Col. address to col. address delay tCCD(min) 1 CLK 3 ea 4 CAS latency=3 2 CAS latency=2 1 Number of valid output data Notes : 1. The minimum number of clock cycles is determined by dividing the minimum time required with clock cycle time and then rounding off to the next higher integer. 2. Minimum delay is required to complete write. 3. All parts allow every cycle column address change. 4. In case of row precharge interrupt, auto precharge and read burst stop. . AC CHARACTERISTICS (AC operating conditions unless otherwise noted) SYMBO -80 -10 -10L PARAMETER L CLK cycle time MIN MAX MIN MAX MIN UNIT NOTE ns 1 ns 1,2 ns 2 ns 3 MAX CAS 8 10 10 latency=3 tCC 1000 1000 1000 CAS 10 10 12 latency=2 CLK to valid CAS output delay latency=3 6 6 6 tSAC CAS 6 6 7 latency=2 Output data CAS hold time latency=3 3 3 3 tOH CAS 3 3 3 3 3 3 latency=2 CLK high pulse width URL:www.hbe.co.kr REV.1.0 (August.2002) tCH -7- HANBit Electronics Co.,Ltd HANBit HSD4M64D4B CLK low pulse width tCL 3 3 3 ns 3 Input setup time tSS 2 2 2 ns 3 Input hold time tSH 1 1 1 ns 3 CLK to output in Low-Z tSLZ 1 1 1 ns 3 2 CLK to output CAS in Hi-Z latency=3 6 6 6 ns 6 6 7 ns tSHZ CAS latency=2 Notes : 1. Parameters depend on programmed CAS latency. 2. If clock rising time is longer than 1ns, (tr/2-0.5)ns should be added to the parameter. 3. Assumed input rise and fall time (tr & tf) = 1ns. If tr & tf is longer than 1ns, transient time compensation should be considered, ie., [(tr + tf)/2-1]ns should be added to the parameter. SIMPLIFIED TRUTH TABLE CKE n-1 COMMAND Register Mode register set Auto refresh Refresh Self refresh Entry Exit Bank active & row addr. Read & column address Write & column address Auto H /C S /R A S /C A S /W E D Q M X L L L L X OP code L L L H X X L H H H X X H L BA 0,1 L H H X X X H X L L H H X V H X L H L H X V precharge disable Auto H CKE N precharge Auto H X L H L L X Precharge precharge Clock suspend or active power down Precharge X L L H L X H X L L H L X Entry H L Exit L H All banks power down mode Entry Exit DQM No operation command 3 3 3 3 Column H (A0 ~ A7) L Address 4 4,5 H L L H H X X X L V V V X X X X H X X X L H H H H X X X L V V V H H X X H X X X L H H H X 4 (A0 ~ A7) H H Bank selection 1,2 Address V disable Burst Stop NOTE Column precharge disable A11 A9~A0 Row address L disable Auto A10/ AP 4,5 X V L X H 6 X X X X X X V X X X (V=Valid, X=Don't care, H=Logic high, L=Logic low) URL:www.hbe.co.kr REV.1.0 (August.2002) -8- HANBit Electronics Co.,Ltd 7 HANBit HSD4M64D4B Notes : 1. OP Code : Operand code A0 ~ A11 & BA0 ~ BA1 : Program keys. (@ MRS) 2. MRS can be issued only at all banks precharge state. A new command can be issued after 2 CLK cycles of MRS. 3. Auto refresh functions are as same as CBR refresh of DRAM. The automatical precharge without row precharge command is meant by "Auto". Auto/self refresh can be issued only at all banks precharge state. 4. BA0 ~ BA1 : Bank select addresses. If both BA0 and BA1 are "Low" at read, write, row active and precharge, bank A is selected. If both BA0 is "Low" and BA1 is "High" at read, write, row active and precharge, bank B is selected. If both BA0 is "High" and BA1 is "Low" at read, write, row active and precharge, bank C is selected. If both BA0 and BA1 are "High" at read, write, row active and precharge, bank D is selected. If A10/AP is "High" at row precharge, BA0 and BA1 is ignored and all banks are selected. 5. During burst read or write with auto precharge, new read/write command can not be issued. Another bank read/write command can be issued after the end of burst. New row active of the associated bank can be issued at tRP after the end of burst. 6. Burst stop command is valid at every burst length. 7. DQM sampled at positive going edge of a CLK and masks the data-in at the very CLK (Write DQM latency is 0), but makes Hi-Z state the data-out of 2 CLK cycles after. (Read DQM latency is 2) TIMING DIAGRAMS Please refer to attached timing diagram chart (II) PACKAGING INFORMATION Unit : mm 2.54 mm MIN 0.25 mm MAX 1.27 ± 0.08 mm (Solder & Gold Plating) 1.27 Gold: 1.04± 0.10 mm 28.25±0.15mm URL:www.hbe.co.kr REV.1.0 (August.2002) Solder: 0.914± 0.10 mm -9- HANBit Electronics Co.,Ltd HANBit HSD4M64D4B ORDERING INFORMATION Part Number Density Org. HSD4M64D4B-10 32Byte x 64 HSD4M64D4B-10L 32Byte x 64 HSD4M64D4B-12 32Byte x 64 HSD4M64D4B-13 URL:www.hbe.co.kr REV.1.0 (August.2002) 32Byte x 64 Package 168 Pin DIMM 168 Pin DIMM 168 Pin DIMM 168 Pin DIMM - 10 - Ref. Vcc 4K 3.3V 4K 3.3V 4K 3.3V 4K 3.3V MAX.frq 100MHz (CL=2) 100MHz (CL=3) 125MHz (CL=3) 133MHz (CL=3) HANBit Electronics Co.,Ltd