SURFACE MOUNT DEVICE LED Part No. : 0805KRCT REV:A / 0 PACKAGE OUTLINE DIMENSIONS BACK VIEW TOP VIEW 1.05 1.25 SIDE VIEW MOLDING BODY (LENS) P.C BOARD R0.10 0.45 POLARITY LED DICE SOLDERING TERMINAL CATHODE 2.00 + 1.50 REF. 0.95 0.45 5.00° 0.80 0.28 ~ 0.30 0.35 Notes: 1. All dimensions are in millimeters. 2. Tolerance is ± 0.1mm (.004") unless otherwise noted. Features Top view, wide view angle, single color Chip LED. Package in 8mm tape on 7" diameter reels. Compatible with automatic Pick & Place equipment. Compatible with Infrared and Wave soldering reflow solder processes. EIA STD package. I.C. compatible. DRAWING NO. : DS-72-03-0008 DATE : 2003-12-12 PAGE 1 SURFACE MOUNT DEVICE LED Part No. : 0805KRCT REV:A / 0 Chip Materials Dice Material : AlInGaP Light Color : Super Red Lens Color : Water Clear Absolute Maximum Ratings(Ta=25℃) Symbol Parameter Rating Unit PD Power Dissipation 75 mW IPF Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) 80 mA IF Continuous Forward Current 30 mA - De-rating Linear From 25℃ 0.25 mA/℃ 5 V 2000 V VR Reverse Voltage Note A ESD Electrostatic Discharge Threshold(HBM) Topr Operating Temperature Range -40 ~ +85 ℃ Tstg Storage Temperature Range -40 ~ +85 ℃ - Wave Soldering Condition (Two times Max.) 260 (for 5 seconds) ℃ - Infrared Soldering Condition (Two times MAX.) 240 (for 5 seconds) ℃ Note A : HBM : Human Body Model. Seller gives no other assurances regarding the ability of to withstand ESD. Electro-Optical Characteristics(Ta=25℃) Parameter Luminous Intensity Symbol Min. Typ. Max. Unit Test Condition IV 16.0 40.0 80.0 mcd IF=20mA Viewing Angle 2θ1/2 130 deg Note 2 Peak Emission Wavelength λp 639 nm Measurement @Peak Dominant Wavelength λd 631 nm IF=20mA Spectral Line Half-Width Δλ 17 nm Forward Voltage VF 2.0 Reverse Current IR DRAWING NO. : DS-72-03-0008 2.4 V IF =20mA 100 μA VR = 5V DATE : 2003-12-12 PAGE 2 SURFACE MOUNT DEVICE LED Part No. : 0805KRCT REV:A / 0 Notes: 1. Luminous intensity is measured with a light sensor and filter combination that proximities the CIE eye-response curve. 2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 3. The dominant wavelength λd is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. 4. Caution in ESD : Static Electricity and surge damages the LED. It is recommend use a wrist band or anti-electrostatic glove when handling the LED. All devices, equipment and machinery must be properly grounded. 5. Major standard testing equipment by “Instrument System” Model : CAS140B Compact Array Spectrometer and “KEITHLEY” Source Meter Model : 2400. Typical Electro-Optical Characteristics Curves Fig.1 Relative Intensity vs. Wavelength DRAWING NO. : DS-72-03-0008 DATE : 2003-12-12 PAGE 3 SURFACE MOUNT DEVICE LED Part No. : 0805KRCT REV:A / 0 Typical Electro-Optical Characteristics Curves Luminous lntensity(mcd) (25℃ Ambient Temperature Unless Otherwise Noted) Fig.2 Forward Current vs.Forward Voltage Fig.3 Luminous Intensity vs.Forward Current Relative luminous intensity(%) Relative Luminous lntensity Normalized of 20mA 1000 100 10 1 -60 -40 -20 -0 20 40 60 80 100 Ambient Temperature Ta(℃) Fig.4 Relative Luminous Intensity vs.Forward Current Fig.5 Luminous Intensity VS Ambient Temperature 0° Forward Current IF(mA) 50 10° 20° 30° 40 30 25 20 1.0 40° 0.9 50° 0.8 60° 70° 80° 90° 10 0.7 1 0 20 40 60 80 100 0.5 0.3 0.1 0.2 0.4 0.6 Ambient Temperature Ta(℃) Fig.6 Forward Current Derating Curve DRAWING NO. : DS-72-03-0008 Fig.7 Forward Current Derating Curve DATE : 2003-12-12 PAGE 4 SURFACE MOUNT DEVICE LED Part No. : 0805KRCT REV:A / 0 Label Explanation BATCH: L1 B9 AC L1: Luminous Intensity Code B9: Forward Voltage Code AC: Dom Wavelength Code Reel Dimensions Notes: 1. Taping Quantity : 3000PCS 2. The tolerances unless mentioned is±0.1mm, Angle±0.5°, Unit : mm. DRAWING NO. : DS-72-03-0008 DATE : 2003-12-12 PAGE 5 SURFACE MOUNT DEVICE LED Part No. : 0805KRCT REV:A / 0 Package Dimensions Of Tape And Reel Progressive direction Polarity Notes:All dimensions are in millimeters. Moisture Resistant Packaging Label Reel Label Desiccant Aluminum moistue-proof bag 240 145 210 255 Label Box 435 Carton Notes : One reel in a bag, one bag in a inner box, ten inner boxes in a carton. DRAWING NO. : DS-72-03-0008 DATE : 2003-12-12 PAGE 6 SURFACE MOUNT DEVICE LED Part No. : 0805KRCT REV:A / 0 Cleaning If cleaning is required , use the following solutions for less than 1 minute and less than 40℃. Appropriate chemicals: Ethyl alcohol and isopropyl alcohol. Effect of ultrasonic cleaning on the LED resin body differs depending on such factors as the oscillator output, size of PCB and LED mounting method. The use of ultrasonic cleaning should be enforced at proper output after confirming there is no problem. Suggest Soldering Pad Dimensions Direction of PWB camber and go to reflow furnace Suggest IR Reflow Soldering Profile Condition: 240 Temperature(℃) Rising +5℃/sec Cooling -5℃/sec 150 120 Time DRAWING NO. : DS-72-03-0008 DATE : 2003-12-12 PAGE 7 SURFACE MOUNT DEVICE LED Part No. : 0805KRCT REV:A / 0 Bin Code List Luminous Intensity(IV), Unit:mcd@20mA Bin Code Min Max M 16.0 32.0 N 25.0 50.0 P 40.0 80.0 Including test tolerance CAUTIONS 1.Application Limitation : The LED’s described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household application).Consult HB’s sales in advance for information on application in which exceptional quality and reliability are required, particularly when the failure or malfunction of the LED’s may directly jeopardize life or health (such as airplanes, automobiles, traffic control equipment, life support system and safety devices). 2.Storage : Before opening the package : The LEDs should be kept at 30°C or less and 85%RH or less. The LEDs should be used within a year. After opening the package : The LEDs should be kept at 30°C or less and 70%RH or less. The LEDs should be soldered within 168 hours(7 days) after opening the package. Please avoid rapid transitions in ambient temperature in high humidity environments where condensation may occur. 3.Soldering Do not apply any stress to the lead frame during soldering while the LED is at high temperature. Recommended soldering condition. Reflow Soldering : Pre-heat 120~150°C, 120sec. MAX., Peak temperature : 240°C Max. Soldering time : 10 sec Max. Soldering Iron : (Not recommended) Temperature 300°C Max., Soldering time : 3 sec. Max.(one time only), power dissipation of iron : 20W Max. use SN60 solder of solder with silver content and don’t to touch LED lens when soldering. Wave soldering : Pre-heat 100°C Max, Pre-heat time 60 sec. Max, Solder wave 260°C Max, Soldering time 5 sec. Max. preformed consecutively cooling process is required between 1st and 2nd soldering processes. DRAWING NO. : DS-72-03-0008 DATE : 2003-12-12 PAGE 8 SURFACE MOUNT DEVICE LED Part No. : 0805KRCT REV:A / 0 4. Drive Method Circuit model A Circuit model B (A)Recommended circuit. (B)The difference of brightness between LED`s could be found due to the Vf-If characteristics of LED. 5.Reliability Test Classification Test Item Test Condition Reference Standard Ta= Under Room Temperature As Per Data Sheet Maximum Rating *Test Time= 1000HRS (-24HRS,+72HRS)*@20mA. MIL-STD-750D:1026 (1995) MIL-STD-883D:1005 (1991) JIS C 7021:B-1 (1982) IR-Reflow In-Board, 2 Times Ta= 65±5℃,RH= 90～95% *Test Time= 1000HRS±2HRS MIL-STD-202F:103B(1980) JIS C 7021:B-11(1982) Ta= 105±5℃ Test Time= 1000HRS (-24HRS,72HRS) MIL-STD-883D:1008 (1991) JIS C 7021:B-10 (1982) Ta= -55±5℃ *Test Time=1000HRS (-24HRS,72H RS) JIS C 7021:B-12 (1982) Temperature Cycling 105±5℃ 10mins MIL-STD-202F:107D (1980) MIL-STD-750D:1051(1995) MIL-STD-883D:1010 (1991) JIS C 7021:A-4(1982) Thermal Shock IR-Reflow In-Board, 2 Times 105±5℃ -55℃±5℃ 10mins 10mins 100 Cycles MIL-STD-202F:107D(1980) MIL-STD-750D:1051(1995) MIL-STD-883D:1011 (1991) Tsol= 260 ± 5℃ Dwell Time= 10 ± 1sec MIL-STD-202F:210A(1980) MIL-STD-750D:2031(1995) JIS C 7021:A-1(1982) Tsol= 235 ± 5℃ Immersion time 2±0.5 sec Immersion rate 25±2.5 mm/sec Coverage ≧95% of the dipped surface MIL-STD-202F:208D(1980) MIL-STD-750D:2026(1995) MIL-STD-883D:2003(1991) IEC 68 Part 2-20 JIS C 7021:A-2(1982) Operation Life High Temperature Endurance Test High Humidity Storage High Temperature Storage Low Temperature Storage Environmental Test Solder Resistance Solder ability -55±5℃ 10mins 100 Cycles 6.Others: The appearance and specifications of the product may be modified for improvement without notice. DRAWING NO. : DS-72-03-0008 DATE : 2003-12-12 PAGE 9