HY5V62CF 4 Banks x 512K x 32Bit Synchronous DRAM DESCRIPTION The Hynix HY5V62C is a 67,108,864-bit CMOS Synchronous DRAM, ideally suited for the memory applications which require wide data I/O and high bandwidth. HY5V62C is organized as 4banks of 524,288x32. HY5V62C is offering fully synchronous operation referenced to a positive edge of the clock. All inputs and outputs are synchronized with the rising edge of the clock input. The data paths are internally pipelined to achieve very high bandwidth. All input and output voltage levels are compatible with LVTTL. Programmable options include the length of pipeline (Read latency of 2 or 3), the number of consecutive read or write cycles initiated by a single control command (Burst length of 1,2,4,8 or full page), and the burst count sequence(sequential or interleave). A burst of read or write cycles in progress can be terminated by a burst terminate command or can be interrupted and replaced by a new burst read or write command on any cycle. (This pipelined design is not restricted by a `2N` rule.) FEATURES • JEDEC standard 3.3V power supply • Auto refresh and self refresh • All device pins are compatible with LVTTL interface • 4096 refresh cycles / 64ms • 90Ball FBGA with 0.8mm of pin pitch • Programmable Burst Length and Burst Type • All inputs and outputs referenced to positive edge of system clock • Data mask function by DQM0,1,2 and 3 • Internal four banks operation - 1, 2, 4, 8 or full page for Sequential Burst - 1, 2, 4 or 8 for Interleave Burst • Programmable CAS Latency ; 2, 3 Clocks • Burst Read Single Write operation ORDERING INFORMATION Part No. Clock Frequency HY5V62CF-7 143MHz HY5V62CF-S 100MHz Power Organization Interface Package Normal 4Banks x 512Kbits x32 LVTTL 90Ball FBGA This document is a general product description and is subject to change without notice. Hynix Semiconductor Inc. does not assume any responsibility for use of circuits described. No patent licenses are implied. Rev. 0.4/Nov. 01 HY5V62CF PIN CONFIGURATION 1 2 3 D Q 26 D Q 24 D Q 28 4 5 6 7 8 9 VSS VDD D Q 23 D Q 21 VDDQ VSSQ VDDQ VSSQ D Q 19 VSSQ D Q 27 D Q 25 D Q 22 D Q 20 VDDQ VSSQ D Q 29 D Q 30 D Q 17 D Q 18 VDDQ VDDQ D Q 31 NC NC D Q 16 VSSQ VSS DQM3 A3 A2 DQM2 VDD A4 A5 A6 A 10 A0 A1 NC BA1 NC A B C D E F G Top View H (11m m x13m m ) A7 A8 NC C LK CKE A9 BA0 CS# RAS# DQM1 NC NC CAS# W E# DQM0 VDDQ DQ8 VSS VDD DQ7 VSSQ VSSQ D Q 10 DQ9 DQ6 DQ5 VDDQ VSSQ D Q 12 D Q 14 DQ1 DQ3 VDDQ D Q 11 VDDQ VSSQ VDDQ VSSQ DQ4 D Q 13 D Q 15 VSS VDD DQ0 J K L M N P R DQ2 PIN DESCRIPTION PIN PIN NAME DESCRIPTION CLK Clock The system clock input. All other inputs are registered to the SDRAM on the rising edge of CLK. CKE Clock Enable Controls internal clock signal and when deactivated, the SDRAM will be one of the states among power down, suspend or self refresh CS Chip Select Enables or disables all inputs except CLK, CKE and DQM BA0, BA1 Bank Address Selects bank to be activated during RAS activity Selects bank to be read/written during CAS activity A0 ~ A10 Address Row Address : RA0 ~ RA10, Column Address : CA0 ~ CA7 Auto-precharge flag : A10 RAS, CAS, WE Row Address Strobe, Column Address Strobe, Write Enable RAS, CAS and WE define the operation Refer function truth table for details DQM0~3 Data Input/Output Mask Controls output buffers in read mode and masks input data in write mode DQ0 ~ DQ31 Data Input/Output Multiplexed data input / output pin VDD/VSS Power Supply/Ground Power supply for internal circuits and input buffers VDDQ/VSSQ Data Output Power/Ground Power supply for output buffers NC No Connection No connection Rev. 0.4/Nov. 01 3 HY5V62CF FUNCTIONAL BLOCK DIAGRAM 512Kbit x 4banks x 32 I/O Synchronous DRAM Self Refresh Logic & Timer Refresh Counter 512Kx32 Bank 3 CLK Row Active Y decoder A0 A1 DQ1 DQ30 DQ31 Column Add Counter Address Register Address buffers Rev. 0.4/Nov. 01 DQ0 I/O Buffer & Logic Column Pre Decoder Bank Select A10 BA0 BA1 Memory Cell Array Sense AMP & I/O Gate Column Active X decoder WE DQM0 DQM1 DQM2 DQM3 512Kx32 Bank 0 X decoder CAS 512Kx32 Bank 1 X decoder RAS 512Kx32 Bank 2 State Machine CS Row Pre Decoder X decoder CKE Burst Counter Mode Register CAS Latency Data Out Control Pipe Line Control 4 HY5V62CF ABSOLUTE MAXIMUM RATINGS Parameter Symbol Rating Unit Ambient Temperature TA 0 ~ 70 °C Storage Temperature TSTG -55 ~ 125 °C Voltage on Any Pin relative to VSS VIN, VOUT -1.0 ~ 4.6 V Voltage on VDD relative to VSS VDD, VDDQ -1.0 ~ 4.6 V Short Circuit Output Current IOS 50 mA Power Dissipation PD 1 W Soldering Temperature ⋅ Time TSOLDER 260 ⋅ 10 °C ⋅ Sec Note : Operation at above absolute maximum rating can adversely affect device reliability DC OPERATING CONDITION (TA=0 to 70°C) Parameter Symbol Min Typ. Max Unit Note Power Supply Voltage VDD, VDDQ 3.0 3.3 3.6 V 1,2 Input high voltage VIH 2.0 3.0 VDDQ + 0.3 V 1,3 Input low voltage VIL VSSQ - 0.3 0 0.8 V 1,4 Note Note : 1.All voltages are referenced to VSS = 0V 2.VDD/VDDQ(min) is 3.15V for HY5V62CF-7/S 3.VIH (max) is acceptable 5.6V AC pulse width with ≤3ns of duration with no input clamp diodes 4.VIL (min) is acceptable -2.0V AC pulse width with ≤3ns of duration with no input clamp diodes AC OPERATING CONDITION (TA=0 to 70°C, 3.0V ≤VDD ≤3.6V, VSS=0V - Note1) Parameter Symbol Value Unit VIH / VIL 2.4/0.4 V Vtrip 1.4 V Input rise / fall time tR / tF 1 ns Output timing measurement reference level Voutref 1.4 V CL 30 pF AC input high / low level voltage Input timing measurement reference level voltage Output load capacitance for access time measurement 2 Note : 1.3.15V ≤VDD ≤3.6V is applied for HY5V62CF-7/S 2.Output load to measure access times is equivalent to two TTL gates and one capacitor (30pF) For details, refer to AC/DC output load circuit Rev. 0.4/Nov. 01 5 HY5V62CF CAPACITANCE (TA=25°C, f=1MHz, VDD=3.3V) Parameter Pin Input capacitance Data input / output capacitance Symbol Min Max Unit CLK CI1 2.5 3.5 pF A0 ~ A10, BA0, BA1, CKE, CS, RAS, CAS, WE, DQM0~3 CI2 2.5 3.8 pF DQ0 ~ DQ31 CI/O 4 6.5 pF OUTPUT LOAD CIRCUIT Vtt=1.4V Vtt=1.4V RT=500 Ω Output RT=50 Ω Z0 = 50Ω Output 30pF 30pF DC Output Load Circuit AC Output Load Circuit DC CHARACTERISTICS I (DC operating conditions unless otherwise noted) Parameter Symbol Min. Max Unit Note Input leakage current ILI -1 1 uA 1 Output leakage current ILO -1 1 uA 2 Output high voltage VOH 2.4 - V IOH = -2mA Output low voltage VOL - 0.4 V IOL = +2mA Note : 1.VIN = 0 to 3.6V, All other pins are not under test = 0V 2.DOUT is disabled, VOUT=0 to 3.6V Rev. 0.4/Nov. 01 6 HY5V62CF DC CHARACTERISTICS II (DC operating conditions unless otherwise noted) Speed Parameter Symbol Test Condition -7 -S 120 115 IDD1 Burst Length=1, One bank active tRAS ≥ tRAS(min), tRP ≥ tRP(min), IOL=0mA IDD2P CKE ≤ VIL(max), tCK = 15ns 2 IDD2PS CKE ≤ VIL(max), tCK = ∞ 2 IDD2N CKE ≥ VIH(min), CS ≥ VIH(min), tCK = 15ns Input signals are changed one time during 2clks. All other pins ≥ VDD-0.2V or ≤ 0.2V 15 IDD2NS CKE ≥ VIH(min), tCK = ∞ Input signals are stable. 10 IDD3P CKE ≤ VIL(max), tCK = 15ns 3 IDD3PS CKE ≤ VIL(max), tCK = ∞ 3 IDD3N CKE ≥ VIH(min), CS ≥ VIH(min), tCK = 15ns Input signals are changed one time during 2clks. All other pins ≥ VDD-0.2V or ≤ 0.2V 40 IDD3NS CKE ≥ VIH(min), tCK = ∞ Input signals are stable 25 Burst Mode Operating Current IDD4 tCK ≥ tCK(min), tRAS ≥ tRAS(min), IOL=0mA All banks active Auto Refresh Current IDD5 tRRC ≥ tRRC(min), 2 banks active Self Refresh Current IDD6 CKE ≤ 0.2V Operating Current Precharge Standby Current in power down mode Precharge Standby Current in non power down mode Active Standby Current in power down mode Active Standby Current in non power down mode Unit Note mA 1 mA mA mA mA CL=3 210 180 CL=2 - 160 210 190 2 mA 1 mA 2 mA Note : 1.IDD1 and IDD4 depend on output loading and cycle rates. Specified values are measured with the output open 2.Min. of tRRC (Refresh RAS cycle time) is shown at AC CHARACTERISTICS I Rev. 0.4/Nov. 01 7 HY5V62CF AC CHARACTERISTICS I (AC operating conditions unless otherwise noted) -7 Parameter Unit Min System clock cycle time CAS Latency = 3 -S Symbol tCK3 Max 7 Min 10 1000 CAS Latency = 2 Note Max ns 1000 tCK2 10 12 ns Clock high pulse width tCHW 2.5 - 3 - ns 1 Clock low pulse width tCLW 2.5 - 3 - ns 1 CAS Latency = 3 tAC3 - 5.4 - 6 ns CAS Latency = 2 tAC2 - 6 - 8 ns Data-out hold time tOH 2.7 - 3 - ns 3 Data-Input setup time tDS 1.5 - 2 - ns 1 Data-Input hold time tDH 0.8 - 1 - ns 1 Address setup time tAS 1.5 - 2 - ns 1 Address hold time tAH 0.8 - 1 - ns 1 CKE setup time tCKS 1.5 - 2 - ns 1 CKE hold time tCKH 0.8 - 1 - ns 1 Command setup time tCS 1.5 - 2 - ns 1 Command hold time tCH 0.8 - 1 - ns 1 CLK to data output in low Z-time tOLZ 1.5 - 2 - ns Access time from clock CLK to data output in high Z-time 2 CAS Latency = 3 tOHZ3 ns 5.4 CAS Latency = 2 tOHZ2 6 ns Note : 1.Assume tR / tF (input rise and fall time ) is 1ns 2.Access times to be measured with input signals of 1v/ns edge rate, 0.8v to 2.0v 3.Data-out hold time to be measured under 30pF load condition, without Vt termination Rev. 0.4/Nov. 01 8 HY5V62CF AC CHARACTERISTICS II (AC operating conditions unless otherwise noted) -7 Parameter -S Symbol Unit Min Max Min Max Operation tRC 62 - 70 - ns Auto Refresh tRRC 62 - 70 - ns RAS to CAS delay tRCD 20 - 20 - ns RAS active time tRAS 42 120K 50 120K ns RAS precharge time tRP 20 - 20 - ns RAS to RAS bank active delay tRRD 14 - 20 - CLK CAS to CAS delay tCCD 1 - 1 - CLK Write command to data-in delay tWTL 0 - 0 - CLK Data-in to precharge command tDPL 1 - 1 - CLK Data-in to active command tDAL 4 - 3 - CLK DQM to data-out Hi-Z tDQZ 2 - 2 - CLK DQM to data-in mask tDQM 0 - 0 - CLK MRS to new command tMRD 1 - 1 - CLK CAS Latency = 3 tPROZ3 3 - 3 - CLK CAS Latency = 2 tPROZ2 2 - 2 - CLK Power down exit time tPDE 1 - 1 - CLK Self refresh exit time tSRE 1 - 1 - CLK Refresh Time tREF - 64 - 64 ms Note RAS cycle time Precharge to data output Hi-Z 1 Note : 1. A new command can be given tRRC after self refresh exit Rev. 0.4/Nov. 01 9 HY5V62CF DEVICE OPERATING OPTION TABLE HY5V62CF-7 CAS Latency tRCD tRAS tRC tRP tAC tOH 143MHz(7ns) 3CLKs 3CLKs 6CLKs 9CLKs 3CLKs 5.4ns 2.7ns 133MHz(7.5ns) 3CLKs 3CLKs 6CLKs 9CLKs 3CLKs 5.4ns 2.7ns 100MHz(10ns) 2CLKs 2CLKs 5CLKs 7CLKs 2CLKs 6ns 3ns HY5V62CF-S CAS Latency tRCD tRAS tRC tRP tAC tOH 100MHz(10ns) 2CLKs 2CLKs 5CLKs 7CLKs 2CLKs 6ns 3ns 83MHz(12ns) 2CLKs 2CLKs 5CLKs 7CLKs 2CLKs 6ns 3ns 66MHz(15ns) 2CLKs 2CLKs 4CLKs 6CLKs 2CLKs 6ns 3ns Rev. 0.4/Nov. 01 10 HY5V62CF COMMAND TRUTH TABLE Command A10/ AP CKEn-1 CKEn CS RAS CAS WE DQM Mode Register Set H X L L L L X OP code H X X X No Operation H X X X L H H H Bank Active H X L L H H X H X L H L H X ADDR RA Read L V H Write L H X L H L L X CA Write with Autoprecharge H X L L H L X Burst Stop H DQM H Auto Refresh H H L L L Entry H L L L H X Exit L H H X L H H L X L V X X V X H X X L H X X X X X X L H H H H X X X L H H H H X X X L H H H H X X X L V V V L Precharge power down H X Precharge selected Bank Entry V H Precharge All Banks X X Exit Clock Suspend Note V CA Read with Autoprecharge Self Refresh1 BA Entry Exit L H L H X L H X X X X Note : 1. Exiting Self Refresh occurs by asynchronously bringing CKE from low to high 2. X = Don′t care, H = Logic High, L = Logic Low. BA =Bank Address, RA = Row Address, CA = Column Address, Opcode = Operand Code, NOP = No Operation Rev. 0.4/Nov. 01 11 HY5V62CF PACKAGE INFORMATION Rev. 0.4/Nov. 01 12